GE AF-600 FP Series User manual

GE Consumer & Industrial
Electrical Distribution
AF-600 FP & AF-650 GPTM
OPCGPIO General Purpose I/O
Option Module
The instructions do not purport to cover all details or variations in equipment nor to provide for every possible
contingency to be met in connection with installation, operation or maintenance. Should further information be
desired or should particular problems arise which are not covered sufficiently for the purchaser’s purposes, the
matter should be referred to the GE company.
AF-600 FP and AF-650 GP are trademarks of the General Electric Company.
GE Consumer & Industrial
41 Woodford Avenue
Plainville, CT 06062
www.geelectrical.com/drives
130R0140 MI33K102 *MI33K102* DET-632

1.1.1 Introduction
This instruction describes the General Purpose I/O option OPCGPIO for use in the AF-600 FP and AF-650 GP series, expanding the number of input/output in the
frequency converter.
The OPCGPIO option includes 3 digital inputs, 2 analog inputs, 2 digital outputs and 1 analog output.
SW firmware version to be installed in the drive control card must be version 3.00 or later versions for AF-650 GP series, and version X.XX for AF-600 FP series.
Check par. ID-43 Software Version for firmware version.
1.1.2 Product Number: OPCGPIO
Illustration 1.1:
AF-650 GP and AF-600 FP OPCGPIO General Purpose I/O Option Module
1
1

1.2.1 Galvanic Isolation in the OPCGPIO
Digital/analog inputs are galvanically isolated from other inputs/outputs on the OPCGPIO and in the control card of the frequency converter. Digital/analogue
outputs in the OPCGPIO are galvanically isolated from other inputs/outputs on the OPCGPIO, but not from these on the control card of the drive.
If the digital inputs 7, 8 or 9 are to be switched by use of the internal 24 V power supply (terminal 9) the connection between terminal 1 and 5 which is illustrated
in the drawing has to be established.
Illustration 1.2: Principle Diagram
AF-650 GP and AF-600 FP OPCGPIO General Purpose I/O Option Module
2
1

1.2.2 Digital inputs - Terminal X30/1-4
Parameters for set-up: E-53, E-54 and E-55
Number of digital
inputs
Voltage level Voltage levels Tolerance Max. Input impedance
30-24 V DC PNP type:
Common = 0 V
Logic “0”: Input < 5 V DC
Logic “0”: Input > 10 V DC
NPN type:
Common = 24 V
Logic “0”: Input > 19 V DC
Logic “0”: Input < 14 V DC
± 28 V continuous
± 37 V in minimum 10 sec.
Approx. 5 k ohm
1.2.3 Analog voltage inputs - Terminal X30/10-12
Parameters for set-up: AN-3#, AN-4# and DR-76
Number of analog voltage inputs Standardized input signal Tolerance Resolution Max. Input impedance
20-10 V DC ± 20 V continuously 10 bits Approx. 5 K ohm
1.2.4 Digital outputs - Terminal X30/5-7
Parameters for set-up: E-56 and E-57
Number of digital outputs Output level Tolerance Max.impedance
20 or 24 V DC ± 4 V ≥600 ohm
1.2.5 Analog outputs - Terminal X30/5-8
Parameters for set-up: AN-6# and DR-77
Number of analog outputs Output signal level Tolerance Max.impedance
10/4 - 20 mA ± 0.1 mA < 500 ohm
AF-650 GP and AF-600 FP OPCGPIO General Purpose I/O Option Module
3
1

1.3.1 Mounting of Option Modules in Slot B
The power to the frequency converter must be disconnected.
For Unit Sizes 12, 13 and 23:
• Remove the Keypad, the terminal cover, and the Keypad frame from the frequency converter.
• Fit the OPCGPIO option card into slot B.
• Connect the control cables and relieve the cable by the enclosed cable strips.
Remove the knock out in the extended Keypad frame delivered in the option set, so that the option will fit under the extended Keypad frame.
• Fit the extended Keypad frame and terminal cover.
• Fit the Keypad or blind cover in the extended Keypad frame.
• Connect power to the frequency converter.
• Set up the input/output functions in the corresponding parameters, as mentioned in this document.
For Unit Sizes 15, 21, 22, 24, 31, 32, 33, 34, 4X, 5X and 6X:
• Remove the Keypad and the Keypad cradle
• Fit the OPCGPIO option card into slot B
• Connect the control cables and relieve the cable by the enclosed cable strips
• Fit the cradle
•FittheKeypad
Unit Sizes 12, 13 and 23 Unit Sizes 15, 21, 22, 24, 31, 32, 33, 34, 4X, 5X and 6X
AF-650 GP and AF-600 FP OPCGPIO General Purpose I/O Option Module
4
1

1.3.2 Mounting Guidelines - Step By Step
These step-by-step instructions describe how to mount the control cables:
• The power to the frequency converter must be disconnected.
• Remove the Keypad, the terminal cover, and the Keypad frame from the frequency converter.
• Fit the OPCGPIO option card into slot B.
• Connect the control cables and relieve the cable by the enclosed cable strips.
• Remove the knock out in the extended Keypad frame, so that the option will fit under the extended Keypad frame.
• Fit the extended Keypad frame and terminal cover.
• Fit the Keypad or blind cover in the extended Keypad frame.
• Connect power to the frequency converter.
• Set up the input/output functions in the corresponding parameters, as mentioned in the Programming Guide.
1.3.3 How To Mount Cables
The graphic below illustrates how to mount the cables.
AF-650 GP and AF-600 FP OPCGPIO General Purpose I/O Option Module
5
1

GE Consumer & Industrial
Electrical Distribution
AF-600 FP & AF-650 GPTM
OPCGPIO General Purpose I/O
Option Module
The instructions do not purport to cover all details or variations in equipment nor to provide for every possible
contingency to be met in connection with installation, operation or maintenance. Should further information be
desired or should particular problems arise which are not covered sufficiently for the purchaser’s purposes, the
matter should be referred to the GE company.
AF-600 FP and AF-650 GP are trademarks of the General Electric Company.
GE Consumer & Industrial
41 Woodford Avenue
Plainville, CT 06062
www.geelectrical.com/drives
130R0140 MI33K102 *MI33K102* DET-632