GE Advantium PSB9100DF User manual

Installation
Istructi n
Advantium ®120V
Built-In SpeedCook
Ovens
PSB9100DF
PSB9100SF
49-40689-1
[vlFL59060910
07-15 GE
Espaflol
For a Spanish version of this manual, visit
our Website at GEAppliances.com.
Para consultar una version en espaflol de
este manual de instrucciones, visite nuestro
sitio de internet GEAppliances.com.

Safet Information
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT- Sove these instructionsfor
locolinspector'suse.
IM PO RTANT -Observeollgoverning
codes ond ordinonces.
• Note to Installer - Be sure to leave these
instructions with the Consumer.
• Note to Consumer - Keep these instructions
with your Owner's Manual for future reference.
• Skill Level- Installation of this appliance
requires basic mechanical and electrical skills.
• Completion Time- 1 Hour.
• Proper installation is the responsibility of the
installer.
Product failure due to improper installation is
not covered under the warranty. See Owner's
Manual for warranty information.
IMPORTANT- Use thisoven onlyforits
intendedpurpose.Never use the oven forworming
or heotingo room. Prolongeduse ofthe oven
withoutproperventilotioncon be hozordous.
CAUTION:
For personolsofety,remove house fuseoroven
circuitbreokerbeforebeginninginstollotion
toovoid severeorfotolshock injury.
ACAUTION:
For personolsofety,the mounting surfocemust
be copoble ofsupportingthe cobinetlood,in
odditiontothe odded weight ofthe 80-pound
oven ond 50-pound drower,plusodditionoloven
loodsof up to 50 pounds oro totolweight ofup
to 160 pounds.
ACAUTION:
For personal safety this product cannot be
installed in cabinet arrangements such as on
island, o peninsula or below o countertop.
CONTENTS
Design Information
Models Available ....................................................................2
Product Dimensions and Clearances ..........................4
Tools Required .......................................................................4
Ports Supplied ........................................................................4
Advance Planning ................................................................4
Installation Preparation
Electrical Requirements ....................................................5
Prepare the Opening .....................................................6, 7
Remove the Packaging .......................................................7
Installation Instructions
Step 1, Slide the Oven into the Cutout ........................8
Step 2, Install Bottom Trim ................................................8
Step 3, Install Mounting Screws .....................................8
Step 4, Finalize Installation ...............................................8
MODELS AVAILABLE
Profile Models:
PSB9100DFWW - White
PSB9100DFBB - Block
PSB9100SFSS - Stainless Steel

Informaci6n de seguridad
ANTES DE COMENZAR
Lea estas instrucdones par completo y con
detenimiento.
IMPORTANTE - Guardeestasinstrucciones
para el usa de inspectores locales.
IMPORTANTE -Cumplacontodoslos
c6digos yordenanzas vigentes.
• Nota al instalador- AsegOrese de dejar estas
instrucciones con el Consumidor.
,, Nota al consumidor- Mantenga estas
instrucciones con el Manual del Propietario para
referencia futura.
• Nivel de capacidad - Lainstalaci6n de este
aparato requiere capacidades mecanicas yel6ctricas
b_sicas.
• Tiempo de finaJizaci6n - 1 hora.
La instalaci6n adecuada es responsabilidad
del instalador.
,, La garantia no cubre fallas producidas
par la instalaci6n inadecuada del producto.
Consulte el Manual del propietario para
obtener informaci6n sabre la garantia.
IMPORTANTE - Utiliceestehomo s61ocon
elobjetivopara elque fue creado.Nunca use el
horno para entibiaro colentaruna habitaci6n.
Eluso prolongado delhomo sinuna ventilaci6n
adecuada puede resultarpeligroso.
APRECAUCI6N:
Para seguridadpersonal,quiteelfusibleo el
interruptor de circuitos de la vivienda antes de
comenzar la instalaci6n a fin de evitar una lesi6n
grave o fatal.
APRECAUCI6N:
Para seguridad personal, la superficie de montaje
debe poder soportar la carga del gabinete,
adem6s de las 80 libras del homo y las BO libras
del caj6n, rods las cargas adicionales del homo de
hasta 50 libras o un peso total de hasta 160 libras.
APRECAUCI6N:
Para su seguridad personal, este producto no
puede set instalado en arreglos de alacena,
coma par ejemplo, islas, peninsulas o debajo de
superficies de trabajo.

Design Information
PRODUCT DIMENSIONS AND CLEARANCES
\
1"
21-1/2"
\
\\
\\ \\
\\\
E
L_J
-,_ 13" _
1-4/5"
26-3/4" _"
I oo oo o_ moo ]
O0 O0 0 00 O0
NOTE: Appearance may vary slightly by model.
18-5/8"
TOOLS REQUIRED
• #2, Phillips screwdriver
• Hondheld drill
• High-speed drill bit, 1/8" diameter
,, 3/8", slot-head screwdriver
PARTSSUPPLIED
• 6 Brass screws (3 required, 3 extra)
• 5 Color-matched screws (4 required, 1 extra)
• Bottom trim
ADVANCE PLANNING
• These ovens may be installed directly into
a 27"-wide oven cabinet.
• The front surface of the oven will be nearly flush
with surrounding cabinetry doors.
• This oven con be installed over any GE single electric
built-in oven or a warming drawer or both.
IMPORTANT: This oven is not approved for use above
another built-in SpeedCook oven, o side-by-side
installation or below o countertop.
• For personal safety, this oven cannot be installed
in o cabinet arrangement such us on island or
peninsula.
• The oven must be installed atleast 36-3/4" above
the floor.
• Allow for clearance to adjacent corners, walls,
drawers, etc.
• Cabinets installed adjacent to wall ovens must hove
on adhesion spec of atleast 194°F temperature
rating.
The oven must be securely installed in a cabinet that
is firmly attached to the house structure. Weight on
the oven door could cause the oven to tip and result
in injury. Never allow anyone to climb, sit, stand or
hang on the oven door.
4

Installation Preparation
ELECTRICAL REQUIREMENTS
Single Advantium 120 Installation:
This product requires a 120-volt, 60 Hz, 1S-amp
circuit and draws 1.8 kilowatts. This product must be
connected to a supply circuit of the proper voltage
and frequency.
• Wire size must conform to the requirements of the
National Electrical Code or the prevailing local code
for this kilowatt rating.
• The power supply cord and plug should be brought
to a separate 15- or 20-ampere branch circuit single
grounded receptacle. The outlet box should be
located within reach of the 48" power cord.
ELECTRICAL LOCATION
--6" t
9"
Locate outlet box in the shaded area
Install a recessed electrical outlet in the back wall
of the opening within 6" of either side and at least
9" above the cutout floor.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of
on electrical short circuit, grounding reduces the
risk of electric shock by providing on escape wire
for electric current. This appliance is equipped with
a cord having a grounding wire with a grounding
plug. The plug must be plugged into an outlet that is
properly installed and grounded.
_WARNING: Improper use of the grounding
plug can result in a risk of electric shock.
AiADVERTENCIA!: El usa inadecuado del
enchufe de conexi6n a tierra puede provocar un
riesgo de descarga el_ctrica.
Important: IPlease read carefully}.
The power cord of this appliance is equipped with
athree-prong (grounding) plug that mutes with a
standard three-prong grounding wall receptacle to
minimize the possibility of electric shock. Consult a
qualified electrician or serviceman if the grounding
instructions are not completely understood, or if
doubt exists as to whether the appliance is properly
grounded.
• Where a standard two-prong wall receptacle is
encountered, it is the personal responsibility and
obligation of the consumer to have it replaced with a
properly grounded three-prong wall receptacle.
Do not, under any circumstances, cut or remove the
third (ground) prong from the power cord.
DO NOT USEAN EXTENSION CORD. If the power
supply cord is too short, have a qualified electrician or
serviceman install an outlet near the appliance.

Installation Preparation
PREPARE THE OPENING
The Advantium 120 can be installed in combination
with other GE appliances. Always follow each
product's Installation Instructions to complete
the installation.
Single Advantium 120 Installation:
Order a 27"-wide single oven cabinet or cut the
opening in a wall to the dimensions shown.
2_ _ 23-1/2"
n
3
Construct
Base
Hin. 3/8"
Plywood
Supported
by2x4
orlx2
Runners all
Four Sides
• Always maintain 36-3/4" minimum height from
the floor to the cutout in any single or combined
installation.
Allow 111/4 '' case trim overlap at the top and
7/8" overlap on the bottom and each side of the
opening.
Oven overlaps will conceal cut edges on all sides
of the opening.
When installed over a single oven or a warming
drawer, allow at least 2" between the two openings.
This separation will provide clearance for bottom
overlap of the Advantium 220 and the other
appliance overlaps.
Construct a solid oven floor of 3/8" min. thick
plywood supported by 2 x 4 runners on all sides.
The support must be level and rigidly mounted,
flush with the bottom edge of the cutout.
PREPARE THE OPENING (CONT.}
Installation over a GE Warming Drawer:
23-1/2"
17-1/2"
W
9-1/4"
36-3/4"
Hin.
4- 25_1/8''_"
Construct
Solid Bottom
Hin. 3/8"
Plywood
Supported
by2x4or
lx 2 Runners
all Four Sides
7_ 2" lVlin
]Jlnstall x or
2 4
2 x 2 Runners
or Solid
Bottom. Hust
Support 100
bs.
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven supports
above the Warming Drawer location do not obstruct
the required interior depth and height. See Warming
Drawer installation instructions for details.

Installation Preparation
PREPARE THE OPENING CCONT.I
Installation over a GE Oven:
17-1/2"
Construct Solid
Bottom Hin.
3/8" Plywood
Supported by
2x4orlx2
Runners oll
Four Sides
2" Min.
Per Oven
Requirement
*If you ore replacing u GE electric double oven
with the combined instollotion of on Advontium
120 undo single oven, use the dimensions shown.
The middle toil seporuting the two openings muy
need to be lurger thun the 2" minimum shown.
PREPARE THE OPENING ICONT.}
Installation over a GE Oven and Warming
Drawer: Construct
27"-- 23-1/2" Solid Bottom
Hin. 3/8"
Plywood
Supported by
2x4orlx2
Runners all
Four Sides
45-1/4"
- 2" Min.
Per Oven
Requirement
2" Min.
NOTE: Additionul cleurunces between the cutouts
muy be required. Check to be sure the oven
supports obove the Worming Drower locution do
not obstruct the required interior depth ond height.
See Worming Drawer installation instructions for
detuils.
CAUTION: Forpersonul sofety, the
mounting surfuce must be cupoble of supporting
the cabinet loud, in uddition to the udded weight
of the 75-pound product, plus udditionul oven
Ioods of up to 50 pounds or o totol weight of 125
pounds.
REMOVE THE PACKAGING
• Lift the oven out of the corton.
• Remove oil pocking moteriol und tope.
• Open the door und remove ports box.
• Locote ports pockoge contuining mounting screws.
7

Installation
[] SLIDE THE OVEN INTO THE CUTOUT
CAUTION: Two people are required
to lift the oven into the opening. Grasp the bottom
at the front and rear. DO NOT USETHE HANDLE
TO LIFTTHE OVEN. DAMAGE WILL OCCUR!
PRECAUCI6N: Serequieren
dos personas para levantar el homo e introducirlo
en la abertura. Agarre la parte inferior par delante
y par detr6s. NO USE LA IANIJA PARA LEVANTAR
EL HORNO. iPUEDE DA--ARSE!
• Lift and hold the oven at the front of the opening.
Hold the oven at a 45° angle and plug in the
power cord.
• Carefully, slide the oven into the cabinet part
way. Leave the oven a few inches forward of the
cabinet frame.
• Check to be sure the power cord is not trapped
under the oven or along the sides of the oven.
[_] INSTALL BOTTOM TRIM
• Align bottom trim tabs to slots in the bottom
of the oven.
_L
_ / ¸
T _ T T
i
I I
Secure the bottom trim to the bottom of the oven
using 3 brass screws provided.
INSTALL MOUNTING SCREWS
" DID [] [][] ]
[][][][] [][] 0 _ O _ [][]
;:":_t)j
rM }_3
• Drill pilot holes through the side flanges, 2 on each
side.
Drive the color-matched screws into the side
flange.
141FINALIZE INSTALLATION
• Turn the power on at the source. The interior light
should come on when the door is opened.
Refer to the Owner's Manual for operating
instructions.
8Printed in Korea

®
Instrucc e
de instalaci6n
Hornos de cocci6n
r6pida empotrados
de 120V Advantium ®
PSB9100DF
PSB9100SF
49-40689-i
MFL59060910
07-13 GE

Informaci6n de seguridad
ANTES DE COMENZAR
Lea estas instrucdones par completo y con
detenimiento.
IMPORTANTE - Guardeestasinstrucciones
para el usa de inspectores locales.
IMPORTANTE -Cumplacontodoslos
c6digos yordenanzas vigentes.
• Nota al instalador- AsegGrese de dejar estas
instrucciones con el Consumidor.
• Nota al consumidor- Mantenga estas
instrucciones con el Manual del Propietario para
referencia futura.
• Nivel de capacidad - Lainstalaci6n de este
aparato requiere capacidades mecanicas yel6ctricas
b_sicas.
• Tiempo de finaJizaci6n - 1 hora.
• La instalaci6n adecuada es responsabilidad
del instalador.
• La garantia no cubre fallas producidas
par la instalaci6n inadecuada del producto.
Consulte el Manual del propietario para
obtener informaci6n sabre la garantia.
IMPORTANTE - Utiliceestehomo s61ocon
elobjetivopara elque fue creado.Nunca use el
horno para entibiaro colentaruna habitaci6n.
Eluso prolongado delhomo sinuna ventilaci6n
adecuada puede resultarpeligroso.
APRECAUCI6N:
Para seguridadpersonal,quiteelfusibleo el
interruptor de circuitos de la vivienda antes de
comenzar la instalaci6n a fin de evitar una lesi6n
grave o fatal.
APRECAUCI6N:
Para seguridad personal, la superficie de montaje
debe poder soportar la carga del gabinete,
adem6s de las 80 libras del homo y las B0 libras
del caj6n, rods las cargas adicionales del homo de
hasta 50 libras o un peso total de hasta 160 libras.
APRECAUCI6N:
Para su seguridad personal, este producto no
puede set instalado en arreglos de alacena,
coma par ejemplo, islas, peninsulas o debajo de
superficies de trabajo.
CONTENIDOS
Informaci6n sobre el dise_o
Modelos disponibles ........................................................2
Dimensiones del producto yespacio libre ............3
Herramientas necesarias ..............................................3
Partes incluidas ..................................................................B
Planificaci6n anticipada .................................................B
Preparaci6n para la instalaci6n
Requisitos el@ctricos ........................................................4
Prepare la abertura .....................................................5, 6
Retire el embalaje .............................................................6
Instalaci6n
Paso 1, deslice el horno dentro del carte .............7
Paso 2, instale el recorte inferior ...............................7
Paso 3, instale los tornillos de montaje ..................8
Paso 4, finalice la instalaci6n ......................................8
MODELOS DISPONIBLES
Modelos Profile:
PSB9100DFWW- Blanco
PSBg100DFBB- Negro
PSBg100SFSS- Acero inoxidable