GE PEB2060SMSS - Countertop Microwave Oven User manual

PART QUANTITY
❒ Trim Frame 1
❒ Bottom Duct 1
❒ Side Duct 1
❒ 4 mm x 12 mm 23
Round-Head Screws (21 required
for installation)
❒ 4 mm x 14 mm 6
Flat-Head Screws (4 required for
installation)
❒ Anti-Tip Brace 1
❒ Anti-Tip Bracket 1
❒ Upper Duct 1
❒ Top Bracket 1
❒ Bottom Bracket 1
❒ Templates 2
PARTS INCLUDED
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Installation Built-In Trim Kits
Instructions JX2027 and JX2030
Read these instructions completely and carefully.
•IMPORTANT – Save these instructions for local
inspector’s use.
•IMPORTANT – Observe all governing codes and
ordinances.
•Note to Installer – Be sure to leave these instructions with the
Consumer.
•Note to Consumer – Keep these instructions for future reference.
•For easier installation and personal safety, we recommend that two people
install this microwave oven.
WARNING —This oven must be plugged into a properly
grounded 3-hole, 120V receptacle as required by the National Electrical Code.
❒ BEFORE YOU BEGIN
• Do not alter or modify any part of this kit or the oven.
• Unplug the microwave oven before attempting installation of this kit.
• Skill level – Installation of this appliance requires basic mechanical and
electrical skills.
• Completion time – 1-3 hours
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered under the Warranty.
• This kit is UL listed for installation alone or over any GE/GE Profile
single electric wall oven. Not for use adjacent to (within 2 feet of) any gas
or electric range, cooktop or oven.
• This kit is for use on models: PEB2060DMBB, PEB2060DMWW,
PEB2060DMCC, PEB2060SMSS, JEB1860DMBB, JEB1860DMWW,
JEB1860DMCC and JEB1860SMSS.
TOOLS YOU WILL NEED
❒ Phillips screwdriver
❒ Pencil
❒ Tape measure
❒ Awl or punch
❒ Drill with 7⁄64″bit or #35
FOR YOUR SAFETY:
WARNING – Before beginning the
installation, switch power off at service panel and lock
the service disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the
service panel.
❒ Level
❒ Scissors (optional)
1
NOTE: This kit has extra screws to prevent the technician from spending extra
time locating a replacement screw in case they lose one during installation.

❒ CUTOUT DIMENSIONS
1
2
* Min. depth with receptacle outside cabinet 191⁄2″
Min. depth with receptacle inside cabinet 22″
120 volt-60 Hertz grounded power receptacle
Installation Instructions
Models 27″30″
Height 163⁄4″163⁄4″
Width 251⁄2″251⁄2″
Depth (min.)* 191⁄2″or 22″191⁄2″or 22″
WARNING — This trim kit uses air
flow from the top, bottom and sides of the trim
frame. Blocking the air flow can cause the microwave
to function improperly and may cause damage to
the microwave.
Allow a 1″clearance beyond the edge of the trim
frame to provide proper air flow.
On 27″models, allow 11⁄8″at the top, 11⁄16″on the
sides and 11⁄4″at the bottom for overlap of the Trim
Frame over the edges of the cutout.
On 30″models, allow 11⁄8″at the top, 21⁄16″on the
sides and 11⁄4″at the bottom for overlap of the Trim
Frame over the edges of the cutout.
FOR INSTALLATION ABOVE A
BUILT-IN OVEN:
Microwave oven should be installed on a 3/8″
plywood base and supported by 2x4 or 1x2 equivalent
runners on all sides. Base must be capable of
supporting a minimum of 100 lbs.
Draw a line on the cutout floor at the center of
the cutout, and extend the line 1/2″down the
face of the cabinet.
Draw a line on the top front face of the cabinet
at the center of the cutout. The line should extend
1/2″up the face of the cabinet. This center line will
be used for mounting the top bracket (see step 7).
Fold or cut the front edge of the template, along
the front guide line. Place the template flush
along the front edge of the cutout floor, aligning
the center line of the template with the center line
of the cutout floor. Mark the center positions with
an awl or center punch for the anti-tip brace
location as shown.
Drill two holes for the anti-tip brace.
Install the anti-tip brace onto the cutout floor
using two round-head screws.
B
C
D
E
D
D
Round-head screws (2)
Anti-Tip Brace
❒ INSTALL THE ANTI-TIP BRACE
2
Depth
Height
11⁄4″Overlap
Width
11⁄8″Overlap
1″Clearance beyond
trim frame
(on all sides)
3″Min.
27″Models: 11⁄16″overlap
30″Models: 21⁄16″overlap
A
DIMENSIONS:
A = 11⁄2″
B = 3″
C = 183⁄16″
D = 1/2″
Bottom of trim kit
must be minimum
of 36″from floor

3
Disconnect the microwave oven before proceeding with the
installation.
Fasten the anti-tip bracket to the bottom duct by using four
round-head screws.
Remove any loose items
inside the microwave oven,
including the turntable
and turntable support.
Carefully turn the
microwave upside down.
Install bottom duct with
four round-head screws
as shown.
A
C
B
D
Front
Rear
Round-Head Screws (4)
Installation Instructions
Set the microwave upright, being careful not to bend the
front flange. Remove the one existing screw from the left
side of the microwave oven.
As indicated on the supplied template (publication
#31-41003), fold or cut along the “cut lines” and place the
template on top of the microwave oven. By aligning the
template with the outside edges of the oven, you will see
exactly where to place the upper duct assembly. Peel off the
backing from the double-sided tape. Carefully position the
side duct and upper duct assembly on the microwave
cabinet, aligning with the bottom screw hole. Press down
firmly on the ducts. Fasten the duct assembly to the left
side of the cabinet with the screw removed above.
B
C
Existing Screw (1)
Round-Head Screws
Microwave Oven Upside Down
❒ INSTALL ANTI-TIP BRACKET
AND BOTTOM DUCT
3
❒ INSTALL SIDE DUCT AND
UPPER DUCT (cont.)
4
Slide the microwave oven part way into the cabinet opening.
Plug in the microwave oven.
The anti-tip bracket must be flat to the cutout floor to engage
correctly with the anti-tip brace as shown. Carefully slide the
microwave back, making sure the power cord is not mashed or cut.
Center the microwave oven within the cutout opening and
slide the microwave oven in place, engaging the anti-tip brace.
Ensure the microwave oven is accurately centered .
A
B
C
Anti-Tip Assembly
Bottom Duct
Round-Head
Screw
Anti-Tip Bracket
Anti-Tip
Brace
D
E
❒ INSTALL MICROWAVE OVEN
INTO CABINET
5
Connect the side duct to the upper duct as shown.
1. Insert projecting tabs of the upper duct into the holes
of the side duct.
2. Bend the tabs up with caution as shown.
NOTE: Remove any oil or dirt on the surface of the
microwave oven before the ducts are attached.
A
(2)
(1)
Upper Duct
Side Duct
3 Tabs
3 Holes
❒ INSTALL SIDE DUCT AND
UPPER DUCT
4

Installation Instructions
Place the trim frame over the microwave oven with the
curved edge at the top.
Press the trim frame into the opening until all sides snap
into place.
Open the microwave oven door. Secure the trim frame
using four flat-head screws (two on the inside top and two
on the inside bottom).
A
B
C
Your trim kit is now fully installed. Replace the turntable
and turntable support that were removed from the inside
of the microwave oven.
Keep these installation instructions and extra screws for
future reference and need. Do not place them in the
microwave oven.
Replace house fuse or close circuit breaker.
A
B
❒ REPLACE ANY LOOSE ITEMS
10
MFL38268401
49-40552
07-07 JR Printed in China
C
❒ INSTALL THE TRIM FRAME
9
Check the leveling by placing a
level at the front and sides of the
microwave. It may be necessary to
add wood shims under the bottom
duct to level the microwave
front-to-back or side-to-side.
❒ CHECK LEVELING
6
Flat-Head
Screws
Flat-Head Screws
❒ INSTALL THE TOP BRACKET
7
Ensure that
Top Bracket
is Level
Align Center
Lines on
Cabinet and
Top Bracket
Mark Screw
Hole Locations
(also on left
side of bracket)
Place the top bracket flange on top of the upper duct with
the opening of the top bracket lined up with the opening
on the upper duct.
Align the center line marking on the top bracket with the
center line drawn on the top front face of the cabinet at the
center of the cutout.
Ensure the top bracket is level and mark screw hole
locations on the cabinet face.
Drill pilot holes through the side holes in the top bracket.
Secure the top bracket to the cabinet using four round-head
screws (see illustration in step 8).
A
B
C
D
❒ INSTALL THE BOTTOM BRACKET
AND SECURE THE TOP BRACKET
8
Round-Head
Screws
Cutout
Opening
Positioning
Flange
Drill pilot holes through the three holes on the front flange
of the bottom duct assembly.
Hold the bottom bracket against the front flange of the
bottom duct assembly, lining up the three holes in the
bottom bracket with the three holes in the bottom duct.
Screw in three round-head screws. Drill pilot holes through
the four holes in the tabs on the sides of the bottom bracket.
Screw in four round-head screws.
A
B