GE FRU-57QL Series User manual

Pub No. DWWR1053E
GC*200YAWC** GC*200YHWC**
GC*200NGWC** GC*200NHWC**
All manuals and user guides at all-guides.com
all-guides.com

1. Features
730.5
1790
106
x AC 220V / 10W
555
201
354
903
x
x AC 220V / 5W
AC 220V / 5W
Fan Cooling System
Molecular Sieve xH-9
ID0.7 x T0.55 x L2200
AC 220V / 192W
Total
R-134a
190g
Fin Type
Weight (kg)
Gross Vol.
(ISO 15502)
Storage Vol.
(ISO 15502)
Diemension
Height (mm)
Depth (mm)
SPECIFICATIONS
Factory No.
Buyer No. GC*200YAWC** GC*200NGWC** GC*200NHWC**
FRU-54QG..
GC*200YHWC**
FRU-57QJ
Freezer Fan Motor
Cooling Cycle
Refrigerant Type
Refrigerant Charge
Evaporator Type
Condenser Type
Dryer
Capillary Tube
Electronic Part
Refrigerator Lamp
Condenser Fan Motor
Freezer Lamp
Refrigerator Fan Motor
Heater
Sensor
Refrigerator Sensor
Freezer Sensor
Defrost Sensor
Defrost Heater
Dispenser Heater
Fuse Temp. (Defrost)
PBN-43
PT-38
Water Pipe Heater
Home Bar Heater
Main Duct Heater AC 220V / 7W
AC 220V / 10Wx
Width (mm)
Refrigerator
104
1790
730.5
903
Freezer
Total
Freezer
354
201
555
Refrigerator 377
241
618
FRU-57QI..
520
FRU-54QE..
604
227
377
618
241
377
177
343
903
604
227
377
520
177
343
903
730.5
1790
117
730.5
1790
115
25W x 2EA
PBN-43
AC 250V, 10A, 77C
DC 13V, 2050rpm
DC 13V, 1850rpm
DC 13V, 1100rpm
25W x 1EA
1
All manuals and user guides at all-guides.com

2. External Size
* Features are model dependent. All model has same size.
SPECIFICATIONS
2
All manuals and user guides at all-guides.com

3. Interior Parts
3-1...200YA..
1) Freezer Pocket (5ea)
2) Cover Feezer Fan
3) Freezer Lamp (25Wx1ea)
4) Ice Tray
5) Freezer Shelf
6) Freezer Case (2ea)
7) Rfrigerator Lamp (25Wx2ea)
8) Rfrigerator Shelf
9) Chilled Case
10) Egg Case
11) Refrigerator Case ( 2ea )
12) Dairy Pocket
13) Refrigator Pocket
3-2. ..200YH..
SPECIFICATIONS
2
3
4
5
6
7
8
9
11
10
12
13
1
1) Freezer Pocket (5ea)
2) Cover Feezer Fan
3) Freezer Lamp (25Wx1ea)
4) Ice Tray
5) Freezer Shelf
6) Freezer Case (2ea)
7) Rfrigerator Lamp (25Wx2ea)
8) Rfrigerator Shelf
9) Chilled Case
10) Egg Case
11) Refrigerator Case ( 2ea )
12) Dairy Pocket
13) Refrigator Pocket
14) Refreshment Pocket
2
3
4
5
6
7
8
9
11
10
1
3
12
13
14
All manuals and user guides at all-guides.com

3-3. ..200NG..
SPECIFICATIONS
4

3-4. ..200NH..
1) Freezer Top Pocket (1ea)
2) The mouth of the ice
3) Freezer Pocket (3ea)
4) Case Ice Crusher
5) Freezer Lamp (25Wx1ea)
6) Freezer Shelf
7) Freezer Case (2ea)
8) Refrigerator Lamp (25Wx2ea)
9) Refrigerator Shelf
10) Wine Rack (*Option)
11) Egg Case
12) Refrigerator Case (3ea)
13) Magic Cool Zone
14) Dairy Pocket
15) Refrigerator Pocket (3 ea)
16) Refrehsment Pocket
3
4
5
6
7
8
9
10
12
11
1
2
14
15
16
13

1) Freezer Top Pocket (1ea)
2) The mouth of the ice
3) Freezer Pocket (3ea)
4) Case Ice Crusher
5) Freezer Lamp (25Wx1ea)
6) Freezer Shelf
7) Freezer Case (2ea)
8) Refrigerator Lamp (25Wx2ea)
9) Refrigerator Shelf
10) Wine Rack (*Option)
11) Egg Case
12) Refrigerator Case (3ea)
13) Magic Cool Zone
14) Dairy Pocket
15) Refrigerator Pocket (4 ea)
3
4
5
6
7
8
9
10
12
11
1
2
14
15
13
All manuals and user guides at all-guides.com

1. Display ( Basic Model )
a Temperature adjustment button for freezer compratment
b Temperature adjustment button for refrigerator compratment
2. Display Control
3. FRZ. SET button
1) Temperature control of freezer compartment
2) Initial power plug in : Medium ( 3 )
- Every time you press the FRZ. SET button, the setting temperature changes below order.
4. REF. SET button
1) Temperature control of refrigerator compartment
2) Initial power plug in : Medium ( 3 )
- Every time you press the REF. SET button, the setting temperature changes below order.
FUNCTIONS ( DISPLAY_Basic Model )
FCP Cotrol
Temp. Display (Set Temp.) Initial Mode : Freezer / Refrigerator set medium ( 3 / 3 )
a
b
5
All manuals and user guides at all-guides.com
all-guides.com

1. Display ( Dispenser Type )
a Temperature adjustment button for freezer compratment
b Super(Quick) freezer compartment button
c Dispenser selction button. ( Water / Crushed ice / Cubed ice )
Ice maker lock button
Reset water filter button after exchanging the filter
d Temperature adjustment button for refrigerator compratment
e Super(Quick) refrigerator compartment button
f Children lock button ( Hold 3 sceconds )
2. Display Control
3. FRZ. SET button
1) Temperature control of freezer compartment
2) Initial power plug in : Medium ( -19C )
- Every time you press the FRZ. SET button, the setting temperature changes below order.
4. SUPER FRZ. Button
When this button press, the QUICK and Speed icon is flicker 6 times and keep ON.
( By pressing the SUPER FRZ. Button again you can stop this function. )
Initial Mode : Freezer / Refrigerator set medium ( -19C / 4C)
Button
Button
Button
FUNCTIONS ( DISPLAY_Dispenser Model )
FCP Cotrol
Temp. Display (Set Temp.)
SUPER FRZ, SUPER REF. Icon
WATER / CUBED ICE / CRUSHED ICE
KEY LOCK ICON
FILTER CHANEGE LED AFTER 6 Month, LED ON
a
b
cf
e
d
6
All manuals and user guides at all-guides.com

5. REF. SET button
1) Temperature control of refrigerator compartment
2) Initial power plug in : Medium ( 4C )
- Every time you press the REF. SET button, the setting temperature changes below order.
6. SUPER REF. Button
When this button press, the QUICK and Speed icon is flicker 6 times and keep ON.
( By pressing the SUPER REF. Button again you can stop this function. )
7. RESET WATER FILTER
After 6 month of first power input, 'Change Filter Icon' is on. When the time comes to change follow the steps.
1) Push the Lock button.
2) Push the 'Filter Reset' button for 3 seconds. Then 'Change Filter'icon is off.
8. WATER/ICE select
1) WATER / CRUSHED ICE / CUBED ICE mode available.
2) Every the button press, the order is WATER - CRUSHED ICE - CUBED ICE.
3) The initial mode is WATER.
9. ICE MAKER LOCK
1) Press the 'Dispenser' button continue. ( Press again, the mode is OFF. )
2) When cleaning the ice storage case or when not use for a long period of time.
9. LOCK button
1) When lock the other buttons, press this button and LOCK icon is active.
( In this mode other button is unable except LOCK button.)
2) To unlock, push the button again.
< REFERENCE >
: Please wait for 2 ~ 3 seconds in order to take final ice or drops of water when taking out cup from the pressing
switches after taking ice or water.
: The actual inner temperature varies depending on the frood status, as the indicated setting temperature is a target
temperature, not actual temperautre within refrigerator.
FUNCTIONS ( DISPLAY_Dispenser Model )
7
All manuals and user guides at all-guides.com

1. Freezer Compartment Control
1) Adjust by the pushing the FRZ.SET button.
2) Compressor & Freezer Fan controlled by each mode ON/OFF point.
3) Freezer Compartment ON/OFF Difference : 2C
- MEDIUM OFF point : -19C
- When Room Temperature (RT) is below 13C, Freezer sensor OFF point 2C up ( so, MEDIUM OFF : -17C )
4) Control Temperature Point in Each Mode
2. Refrigerator Compartment Control
1) Adjust by the pushing the REF.SET button.
2) Refrigerator Fan controlled by each mode ON/OFF point.
3) Freezer Compartment ON/OFF Difference : 0.5C
- MEDIUM OFF point : 4.2C
- When Room Temperature (RT) is below 13C, Refrigerator sensor OFF point 2C up ( so, MEDIUM OFF : 6.2C )
4) Control Temperature Point in Each Mode
FUNCTIONS ( TEMPERATURE CONTROL_Basic Model )
Initially On 1st Press 2nd Press 3rd Press 4th Press
Sensor On -14.0 -15.0 -17.0 -11.0 -13.0
Sensor Off -16.0 -17.0 -19.0 -13.0 -15.0
Sensor On -12.0 -13.0 -15.0 -9.0 -11.0
Sensor Off -14.0 -15.0 -17.0 -11.0 -13.0
Normal
RT <= 13C
Min Medium
Min
Control
512Display
Medium
Max Max
Division
34
Temperature Medium
Initially On 1st Press 2nd Press 3rd Press 4th Press
Sensor On 4.7 3.7 2.7 6.7 5.7
Sensor Off 4.2 3.2 2.2 6.2 5.2
Sensor On 6.7 5.7 4.7 8.7 7.7
Sensor Off 6.2 5.2 4.2 8.2 7.2
Sensor On 11.2 10.2 9.2 13.2 12.2
Sensor Off 4.2 3.2 2.2 6.2 5.2
Sensor On 13.2 12.2 11.2 15.2 14.2
Sensor Off 6.2 5.2 4.2 8.2 7.2
Normal
RT <= 13C
Weak refrigeration
Weak refrigeration
& RT <= 13C
2
Temperature Medium Medium
Max Max Min Medium Min
3451
Division
Display
8
All manuals and user guides at all-guides.com

1. Freezer Compartment Control
1) Adjust by the pushing the FRZ.SET button.
2) Compressor & Freezer Fan controlled by each mode ON/OFF point.
3) Freezer Compartment ON/OFF Difference : 2C
- MEDIUM OFF point : -19C
- When Room Temperature (RT) is below 13C, Freezer sensor OFF point 2C up ( so, MEDIUM OFF : -17C )
4) Control Temperature Point in Each Mode
6) SUPER FRZ. (QUICK) Mode
- In this mode, Compressor & Freezer Fan motor is on unconditionally for 150min. ( free of freezer sensor )
FUNCTIONS ( TEMPERATURE CONTROL_Dispenser Model )
Initially On 1st Press 2nd Press 3rd Press 4th Press 5th Press 6th Press
Sensor On -14.8 -15.8 -16.8 -17.8 -11.8 -12.8 -13.8
Sensor Off -16.8 -17.8 -18.8 -19.8 -13.8 -14.8 -15.8
Sensor On -12.8 -13.8 -14.8 -15.8 -9.8 -10.8 -11.8
Sensor Off -14.8 -15.8 -16.8 -17.8 -11.8 -12.8 -13.8
-18-21 -22
Min
-16 -17
Medium Max Max Medium Min
-19 -20
Division
Control
Temperature
Normal
RT <= 13C
Medium
Display
Freezer
Sensor
Freezer
Fan On/Off
SUPER FRZ. Start
( SUPER FRZ. MODE ) NORMAL MODE Start
150MIN
9
All manuals and user guides at all-guides.com

2. Refrigerator Compartment Control
1) Adjust by the pushing the REF.SET button.
LOW - MEDIUM LOW - MEDIUM - MEDIUM MAX - MAX
2) Refrigerator Fan controlled by each mode ON/OFF point.
3) Refrigerator Compartment ON/OFF Difference : 0.5C
- MEDIUM OFF point : 5.2C
- When Room Temperature (RT) is below 13C, Refrigerator sensor OFF point 2C up ( so, MEDIUM OFF : 7.2C )
4) Weak Cooling Prevention Function
- This funtion is free of Freezer sensor.
- When refrigerator compartment reaches the Fan OFF point, the Fan is OFF.
and then Compressor controlled by Freezer sensor.
- Weak cooling temperautre is + 7C in each sensor OFF temperature.
- Weak cooling terminate temperautre is same as each sensor OFF temperature.
6) Control Temperature Point in Each Mode
7) SUPER REF. (QUICK) Mode : This mode runs for 40 minutes.
- Until the sensor reaches the Excess Refrigeration OFF point ( -7C), Refrigerator Fan and compressor is ON.
- Until the QUICK Mode ends, the appliance runs with MAX dial mode.
- After QUICK Mode ( about 40 mins ) the normal mode start.
FUNCTIONS ( TEMPERATURE CONTROL_Dispenser Model )
Freezer
Sensor
Excess
Refrigeration
OFF point
ON/OFF
MAX MODE
NORMAL MODE
Start
QUICK MODE (40MIN )
Initially On 1st Press 2nd Press 3rd Press 4th Press 5th Press 6th Press
Sensor On 5.7 4.7 3.7 9.7 8.7 7.7 6.7
Sensor Off 5.2 4.2 3.2 9.2 8.2 7.2 6.2
Sensor On 7.7 6.7 5.7 11.7 10.7 9.7 8.7
Sensor Off 7.2 6.2 5.2 11.2 10.2 9.2 8.2
Sensor On 12.2 11.2 10.2 16.2 15.2 14.2 13.2
Sensor Off 5.2 4.2 3.2 9.2 8.2 7.2 6.2
Sensor On 14.2 13.2 12.2 18.2 17.2 16.2 15.2
Sensor Off 7.2 6.2 5.2 11.2 10.2 9.2 8.2
Medium Min
7658
Medium Max Max Min
Normal
Weak refrigeration
RT <= 13C
Weak refrigeration
& RT <= 13C
Division
Display
Temperature
4
Medium
32
10
All manuals and user guides at all-guides.com
all-guides.com

1. When Defrost Mode start?
; When total Compressor runnig time becomes at 6, 8, 10, …, 24hours.
- The compressor runing rate is over 85% every 2 hours.
- Door opening time is over 2 minutes ( Each Freezer / Refrigerator door )
- Total compressor running time ( on time + off time ) is 60hours.
- Any error happens. ( R1, F1, D1, F3, RT-Sensor, C1, Door switch etc. )
( But, F3 error happens then defrost mode start without Pre-cool )
FUNCTIONS ( Defrost Mode )
Compressor runing
time is over 2hours
Start
Total appiance runing
time is over 60hours
Yes
No
Compressor runing
time is over 24hours
Compressor runing
time is over 6hours
Any error happens
Room temperature is
over 35C
Compressor runing rate is
over 85% every 2 hours
Door open ( each door )
is over 2 minutes
End
No
Yes
No
No
No
No
Yes
No
No
Defrost mode start
Yes
Yes
Yes
Yes
Yes
11
All manuals and user guides at all-guides.com

2. Normal Defrost Mode
3. Forced Defrost Mode
1) How to start
( Basic Models Only )
; Press the REF. SET button 5 times while pushing the FRZ. SET button.
( Dispenser Models Only )
- Press the LOCK button.
- Press the Refrigerator Set button 5 times while pushing the Freezer Set button.
2) Except PRECOOL, steps are same as above 2. Normal Defrost Mode.
FUNCTIONS ( Defrost Mode )
PRECOOL
HEATER
DEFROTING
PAUSE
FAN DELAY
1) PRECOOL
- Compressor runs ( to cool down the freezer compartment prior to heater switch on )
for 50minutes or until Freezer sensor temperature reaches -27C
2) HEATER DEFROSTING
- Defrost heater is switch on until Defrost Sensor temperature reaches 13C.
- Heater operation time
; 30 seconds - Heater is ON free of Defrost Sensor.
; 30 minutes - When Defrost Sensor is malfunction. ( D1 error )
; 80 minutes - Heater maximum operation time. ( F3 error )
3) PAUSE
- After Defrost Heater switch OFF, Compressor dosen't run within 7 minutes.
4) FAN DELAY
- Freezer & Refrigerator fan switch on after 5miunuts' cmopressor running.
30min ( D1 error )
80min ( F3 error)
ON OFF
Off ON
OFF
7min 5min
OFF OFF
OFFOFF
OFF
Control OFF
FAN DELAY
ON OFF OFF ON
PAUSEHEATER DEFROSTPRECOOL
Defrsot Heater
Time
Division
Compressor
Freezer Fan
Refrigerator Fan
50min
Normal Mode
12
All manuals and user guides at all-guides.com

1. How to enter this check mode
; Press the FRZ. SET button 5 times while pushing the REF. SET button.
2. The Front LED displays the current error code ( if happens ).
3. How to exit this mode
1) Press the FRZ.SET button
2) After 4 minutes automatically exit.
4. Error Code
No
1
2
3
4
5
6
7
8
; All Error Code reset, when the relative parts turn into normal.
Abnormal return after defrosting
Freezer Door switch is defective.
Abnormal or defective cycle
Defrost sensor disconnection or short
Refrigerator Door switch is defective.
Refrigerator sensor disconnection or short
Room temperature sensor disconnection or short
FUNCTIONS ( Error Display_Basic Model )
Display (LED flicker) Remark
Freezer sensor disconnection or short
13
All manuals and user guides at all-guides.com

5. Troubleshooting when error happens
( If the relative parts is normal, Error code display will be reset. )
1) Freezer sensor error
- Cause : Freezer sensor disconnection or short.
- Check point : Measure the resistance between both terminals after separating CN9 of the Main PCB.
If sensor is disconnected or short, change that in the freezer compartment.
2) Refrigerator sensoer error
- Cause : Refrigerator sensor disconnection or short.
- Check point : Measure the resistance between both terminals after separating CN8 of the Main PCB.
If sensor is disconnected or short, change that in the refrigerator compartment.
3) Room temperature sensor error
- Cause : Room temperature sensor disconnection or short.
- Check point : Measure the voltage of sensor part on the Main PCB.
If voltage is 0.5~4.5V, normal. If voltage is 0V (short) or 5V (disconnect), change new one.
4) Defrost sensor error
- Cause : Defrost sensor disconnection or short.
- Check point : Measure the resistance between both terminals after separating CN9 of the Main PCB.
If sensor is disconnected or short, change that on the evaporator.
5) Refrigerator door switch error
- Cause : When it senses the door open for more than 1 hour.
- Check point : Check the each door switch and exchange.
6) Freezer door switch error
- Cause : When it senses the door open for more than 1 hour.
- Check point : Check the each door switch and exchange.
7) Cycle error
- Cause : When compressor works for over 3 hours although Defrost sensor is over -5C.
- Check point : Refrigerant leakage.
8) Abnormal defrosting end error
- Cause : in case defrosting mode ends after 80 minutes.
- Check point : Measure the resistance between both terminals of the defrost heater.
If the resistance is infinity (disconnection) or 0 ohm (short).
FUNCTIONS ( Error Display_Basic Model )
14
All manuals and user guides at all-guides.com

1. How to enter this check mode
1) Press the LOCK button.
2) Press the Super Freezer button 5 times while pushing the Freezer Set button.
2. The Front LED displays the current error code ( if happens ).
; Every time you press the Freezer Set button, the following value display.
1) The appliance running time. ( From the plug in. )
2) Freezer sensor temperature.
3) Defrost sensor temperature.
4) Refrigerator sensor temperature.
5) Room temperature.
6) P Factor display.
7) Filter remaing time until exchange. ( Filter runing time is about 4,320Hr )
3. How to exit this mode
1) Press the LOCK button
2) After 4 minutes automatically exit.
4. Error Code
No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
; All Error Code reset, when the relative parts turn into normal.
FUNCTIONS ( Error Display_Dispenser Models )
Display (Error Code) Remark
F1 Freezer sensor disconnection or short
r1 Refrigerator sensor disconnection or short
rt Room temperature sensor disconnection or short
d1 Defrost sensor disconnection or short
dr Refrigerator Door switch is defective.
dF Freezer Door switch is defective.
dH Home Bar Door switch is defective.
El Ice sensor disconnection or short
EF Flow sensor is defective.
Et Horizontal switch error
Eg Water supply error
EA Drop the ice while Et
Eu Full ice switch error
C1 Abnormal or defective cycle
F3 Return after defrosting : abnormal or defective
Co Pull-Down mode display (No error)
d2 Forced Defrost mode display (No error)
15
All manuals and user guides at all-guides.com
all-guides.com

5. Troubleshooting when error happens
( If the relative parts is normal, Error code display will be reset. )
1) F1 error
- Cause : Freezer sensor disconnection or short.
- Check point : Measure the resistance between both terminals after separating CN15 of the Main PCB.
If sensor is disconnected or short, change that in the freezer compartment.
2) R1 error
- Cause : Refrigerator sensor disconnection or short.
- Check point : Measure the resistance between both terminals after separating CN14 of the Main PCB.
If sensor is disconnected or short, change that in the refrigerator compartment.
3) rt error
- Cause : Room temperature sensor disconnection or short.
- Check point : Measure the voltage of sensor part on the Main PCB.
If voltage is 0.5~4.5V, normal. If voltage is 0V (short) or 5V (disconnect), change new one.
4) d1 error
- Cause : Defrost sensor disconnection or short.
- Check point : Measure the resistance between both terminals after separating CN15 of the Main PCB.
If sensor is disconnected or short, change that on the evaporator.
5) Door switch error ( dr, dF, dH on display )
- Cause : When it senses the door open for more than 1 hour.
- Check point : Check the each door switch and exchange.
6) EI error
- Cause : Ice sensor is abnormal.
- Check point : Measure the resistance between both terminals after separating CN11 of the Main PCB.
If sensor is disconnected or short, change that in the automatic ice maker.
7) EF error
- Cause : When Flow-sensor abnormal. ( There is no pulse during some time. )
The number of pulse signal is below 10 by 1 second during water supply.
- Check point : Water supply line.
8) Et error
- Cause : Level switch abnormal. ( No pulse is sensed for some time. )
- Control : By time. ( Supply mode is skipped. )
FUNCTIONS ( Error Display_Dispenser Models )
16
All manuals and user guides at all-guides.com

9) Eg error
- Cause : When Ice sensor temperature ( 5 minutes after water supply ) doesn't go up.
- Check point : Ice sensor or water supply line.
10) EA error
- Cause : When sensing ice drop 3 times in level sensor switch error.
- Control : Stop ice maker
- After 1 time rotation EA error code disappear if level swtich is normal.
11) Eu error
- Cause : Sensor which senses if ice is full or not is abnormal.
- Control : When drops the ice, the motor rotates 90 degree.
12) C1 error
- Cause : When compressor works for over 3 hours although Defrost sensor is over -5C.
- Check point : Refrigerant leakage.
13) F3 error
- Cause : in case defrosting mode ends after 80 minutes.
- Check point : Measure the resistance between both terminals of the defrost heater.
If the resistance is infinity (disconnection) or 0 ohm (short).
FUNCTIONS ( Error Display_Dispenser Models )
17
All manuals and user guides at all-guides.com

1. Ice making flow
1) Press Test switch ( which is under the ice tray ) for more than 1 second and then test starts.
- Test mode starts from ice separating mode.
- In case test switch is abnormal, test is done only 1 time.
2) When the initial power input, ice tray turns to be horizontal.
3) Water supply hose heater control - defrost heater linkage operation
- Heater is always ON if Room temperature sensor is abnormal or room temperature is below 15 degree.
- Heater is ON for 60minutes (max limit time) if Flow sensor is abnormal.
4) Water supply stand by
- Condition : When ice is full
- Operation : Proceeds to ice making mode. ( stop ice separating and water supply mode )
5) Crusher function
- It stops operation when freezer door is open.
- It operates if door is close.
FUNCTIONS ( Ice Maker_ Dispenser Model)
Start
Making the Ice
Ice separating
Water supply
Water supply
check
End
- water freezing
water supply stand b
y
- Ice tray rotation to separate ice cubes
- water supply to ice tray
- check if water supply complete or not
18
All manuals and user guides at all-guides.com

2. Ice making mode
1) If Ice sensor temperature is below -12.5C after 130minutes, ice making completes.
2) If Ice sensor temperature keep below -9.5C for 15 minutes ice making complete, although the sensor is not below -12.5C
3) After 4.8hours ice making complete, when ice sensor is abnormal,
3. Ice separating(drop) mode
1) Time of each section is to verify level switch error.
2) It senses the rotation in each section.
3) When level switch is error, ice separation controlled by the time.
4) When rotation motor is error, the mode is pause.
FUNCTIONS ( Ice Maker_ Dispenser Model)
Start
130 minutes pass
Ice sensor is over
-12.5C
Ice separating
Ice sensor is below
-9.5C
15 minutes pass
NO NO
NO
YES
YES
YES
NO
YES
19
All manuals and user guides at all-guides.com