GE Monogram ZIC360NHLH User manual

SECTION 1
Product Specification Created 7/14
ZIC360NHLHGE Monogram®36" Built-In Bottom-freezer Refrigerator
SECTION 2
1/4" FRAMED PANELS 3/4" OVERLAY PANELS
FLUSH INSET INSTALLATION
STANDARD INSTALLATION

OVERALL DIMENSIONS
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.
† Dimensions include 3/4" custom cabinet panel
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply
is required. An inidividual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
FLUSH INSET INSTALLATION
Product Specification Created 7/14
ZIC360NHLHGE Monogram®36" Built-In Bottom-freezer Refrigerator
SPECIFICATIONS
Overall Width 38" (96.5 cm)†
Overall Height 83 1/2" (212.1 cm)†
Overall Depth 25 7/8" (65.7 cm)†
Door Clearance 38 3/4" (98.4 cm)
Cutout Width 39" (99.1 cm)
Cutout Height 84 1/2" (214.6 cm)
Cutout Depth 26 3/16" (66.5 cm)
Plumbing Requirements 1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight 640 lb (290.3 kg)
38" (96.5)
9 5/8"
(24.4)
20 5/8" (52.4)
25 7/8" (65.7)
* 83 1/2"
(212.1)
*73 1/4"
(186.1)
*26"
(66.0)
*3 3/8"
(8.6)
*3 3/8"
(8.6) SIDE VIEWFRONT VIEW
* 83 1/2"
(212.1)
35" (89.0)
Case width
38 3/4"
(98.4)
TOP VIEW
ZIC360NHLH
** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.
** Allow 17" (43.2) min
clearance for 115˚
door swing
* Shipping height. Use leveling legs and wheels for maximum 1" height
adjustment from shipping height. Nominal installation height is 84”

AMounting the junction
box in this location will
also allow for front
accessability through
access panel.
BWater supply area.
WARNING:
The refrigerator is top
heavy and must be secured
to prevent the possibility of
tipping forward. Failure to
do so may result in death
or serious injury.
The information below is
for cabinet design only.
When installing the anti-
tip system you must use
the product installation
instructions.
The information below
applies to all installation
constructions:
• A wall bracket, bolts and
toggles will be supplied
with the unit.
• The bolts will be used to
attach bracket to wall in
4 locations. Two of the
locations must penetrate
the center of the wall
studs.
• The toggles are used for
stability in drywall and
when metal studs are
encountered. Lag bolts
are used in wood studs.
• In installation opening,
measure 81 ½” from
floor and draw a
horizontal line.
• Locate and mark the wall
studs on horizontal line.
Verify at least two studs
have their centerlines
within the center 32.5”
of installation opening to
ensure 2 wall studs are
penetrated.
• The bracket will be
centered left to right in
opening with bottom of
bracket on the horizontal
line.
• When unit is placed in
opening, the bracket tabs
will align with openings
in back of the unit. The
unit will be secured to the
bracket using supplied
“L” bolts.
See Installation
Instructions for detailed
instructions.
FLUSH INSTALLATION
ZIC360NHLH_RH
39" (99.1) Flush inset width
37 1/2" (95.3)
Width between cleats
3/4" (1.9)
Width of side cleats
5 1/4" (13.3)
1/2" (1.3)
26 3/16" (66.5)
Flush inset depth
20 15/16" (53.2)
Depth to cleat
FRONT VIEWSIDE VIEW
TOP VIEW
3 1/2"
(8.9)
W
Finished cleats
Finished cleats
Case Trim
3/4" Panel
Case
Door
6"
(15.2)
24 3/4"
(62.9)
7"
(17.8)
7"
(17.8)
10"
(25.4)
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
ELEC.
84"
(214)
height
to cleat
84 1/2"
(214.6)
WATER
3 1/2"
(9.0)
NOTES
FLUSH INSET INSTALLATION 3/4" PANELS FLUSH INSET INSTALLATION
Product Specification Created 7/14
ZIC360NHLHGE Monogram®36" Built-In Bottom-freezer Refrigerator
A
B
ANTI-TIP BRACKET
24" (61.0)
1 1/2"
(3.8)
3"
(7.6)
7/16" (1.1)
Trim overlap
35 1/2" (90.2)
2 5/16"
(5.9)
SIDE VIEWFRONT VIEW
ZIC360NXRH
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
ELEC. 6"
(15.2)
10"
(25.4)
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
81 1/2"
(207.0)
WATER
5"
(12.7)
5"
(12.7)
3 1/2"
(9.0)
WATER
10" (25.4)
Use two
additional hole
locations at end
of brackets
Wall
Studs
Bracket
mounted
into vertical
wall studs
centered
within the
cutout
C
Ensure holes
selected are
centered on
the studs
L
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET

NOTES
Trimmed refrigerators are designed to be
customized with decorative panels. Field-
installed custom door and grille panels
are required.
Adjustment brackets allow 1/8” ne
adjustment of panel position in 3
dimensions.
Use templates provided to locate mounting
brackets on the door and grille panels.
Maximum total panel weight:
• Fresh food door panels – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 11 lbs
Door Handles
Door handles not included. Custom handles
supplied by your cabinet maker may be used.
ZKHPSS1: Professional tubular stainless steel
handle designed to fit 3/4” panels. Kit includes
one handle – 30 1/2” long. Order 2 kits from
your Monogram supplier.
ZKHCSS2: European tubular handle designed
to fit 3/4” panels. Kit includes 2 handles.
Door handle is 44 3/16” and drawer handle
is 33 3/16".
Order ZUGF2H: Unified grille kit for dual
installation. Maximum total panel
weight - 25 lbs.
FLUSH INSET INSTALLATION
Product Specification Created 7/14
ZIC360NHLHGE Monogram®36" Built-In Bottom-freezer Refrigerator
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
B
C
D
X
ROUTER 1/4" DEEP
HINGE CLEARANCES
Y
Z
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
Fresh
Food
Panel
Freezer Drawer Panel
E
B
C
D
A B C D
38" 9 5/8" 46 1/2" 22 5/16"
X Y Z
1 1/4" 1" 1/2"
PANEL DIMENSIONS
A B C D E
74 1/2" 9 5/8" 46 1/2" 22 5/16" 37"
PANEL DIMENSIONS
HINGE CLEARANCE
X Y Z
1 1/4" 1" 1/2"
HINGE CLEARANCE
PANEL ASSEMBLY CROSS SECTION
PANEL ASSEMBLY CROSS SECTION
FLUSH INSET 3/4" PANEL DIMENSIONS SINGLE INSTALLATION
1/4" Router Cut Depth
for Hinge Clearance
Door
3/4" Flush Inset Panel
PANEL ASSEMBLY CROSS SECTION
Finished Side of Panel
1/4" Router Cut Depth
for Hinge Clearance
Door
3/4" Flush Inset Panel
PANEL ASSEMBLY CROSS SECTION
Finished Side of Panel
X
ROUTER 1/4" DEEP
HINGE CLEARANCES
Y
Z
FLUSH INSET 3/4" PANEL DIMENSIONS DUAL INSTALLATION

NOTES
FLUSH INSET INSTALLATION
Product Specification Created 7/14
ZIC360NHLHGE Monogram®36" Built-In Bottom-freezer Refrigerator
AA separate 115V, 60Hz, 15- or 20-amp
power supply is recommended for each
product.
BIn a side-by-side installation of a left-and-
right-hand door swing product, 1 1/2”
clearance between the units is required.
Order ZUGF2H custom panel unified grille
kit for this installation.
DUAL PRODUCT CLEARANCES
DUAL INSTALLATIONS
ZIC360NHLH_ZIC360NHRH
75 1/2" (191.8)
Finished Width
26 3/16" (66.5)
Min. Cutout Depth
25 3/4" (65.4)
3 7/8"
(9.8)
5 1/2"
(13.9)
9"
(22.9)
84 1/2"
(214.6)
Finished
Opening
3 1/2"
(8.9)
W
FRONT VIEW
ELEC. 5 1/2"
(13.9)
9"
(22.9)
3 1/2"
(8.9)
25" (63.5) min
To wall 25" (63.5) min
To wall
1 1/2"
(3.8)
130˚
Door swing 130˚ Door swing
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
ELEC.
SIDE VIEW
7"
(17.8) 7" (17.8)
WATER
3 1/2"
(9.0)
WATER
3 1/2"
(9.0)
5 3/4"
(14.6) 5 3/4" (14.6)
ZIC360NHLH_ZIC360NHRH
75 1/2" (191.8)
Finished Width
26 3/16" (66.5)
Min. Cutout Depth
25 3/4" (65.4)
3 7/8"
(9.8)
5 1/2"
(13.9)
9"
(22.9)
84 1/2"
(214.6)
Finished
Opening
3 1/2"
(8.9)
W
FRONT VIEW
ELEC. 5 1/2"
(13.9)
9"
(22.9)
3 1/2"
(8.9)
25" (63.5) min
To wall 25" (63.5) min
To wall
1 1/2"
(3.8)
130˚
Door swing 130˚ Door swing
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
ELEC.
SIDE VIEW
7"
(17.8) 7" (17.8)
WATER
3 1/2"
(9.0)
WATER
3 1/2"
(9.0)
5 3/4"
(14.6) 5 3/4" (14.6)
A
B

OVERALL DIMENSIONS STANDARD INSTALLATION
Product Specification Created 7/14
ZIC360NHLHGE Monogram®36" Built-In Bottom-freezer Refrigerator
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply
is required. An inidividual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
SPECIFICATIONS
Overall Width 36" (91.4 cm)
Overall Height 84" (213.4 cm)
Overall Depth 25 3/8" (64.5 cm)
Door Clearance 36 3/4" (93.4 cm)
Cutout Width 35 1/2" (90.2 cm)
Cutout Height 83 1/2" - 84 1/2"
(212.1 - 214.6 cm)
Cutout Depth 24" (61 cm)
Plumbing Requirements 1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight 640 lb (290.3 kg)
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimension may vary due to manufacturing tolerances.
36" (91.5)
9 7/8"
(25.1)
25 1/4" (64.1)
23 7/8" (60.7)
1 7/8"
(4.8)
* 84"
(213.4)
46 1/4"
(117.5)
*73 1/4"
(186.1)
*26"
(66.0)
*26 1/2"
(16.5)
*24 1/8"
(61.3)
*3 5/8"
(9.2) SIDE VIEWFRONT VIEW
* 83 1/2"
(212.1)
35" (89.0)
Case width
36 3/4"
(93.4)
TOP VIEW
ZIC360NXLH
* Shipping height. Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.
** Allow 25" (63.5) min
clearance for 130˚
door swing
36" (91.5)
9 7/8"
(25.1)
25 1/4" (64.1)
23 7/8" (60.7)
1 7/8"
(4.8)
* 84"
(213.4)
46 1/4"
(117.5)
*73 1/4"
(186.1)
*26"
(66.0)
*26 1/2"
(16.5)
*24 1/8"
(61.3)
*3 5/8"
(9.2) SIDE VIEWFRONT VIEW
* 83 1/2"
(212.1)
35" (89.0)
Case width
36 3/4"
(93.4)
TOP VIEW
ZIC360NXLH
* Shipping height. Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.
** Allow 25" (63.5) min
clearance for 130˚
door swing

24" (61)
1 9/16"
(3.97)
3 1/8"
(7.93) 35 1/2" (90.2)
2 5/16"
(5.874)
7/16" (1.1)
Trim overlap
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
*84 1/2"
(214.6)
*Trim will overlap
additional 7/16"
6"
(15.24)
10"
(25.4)
ELEC.
SIDE VIEW FRONT VIEW
TOP VIEW
W
STANDARD INSTALLATION
ZIC360NHLH_RH
WATER
5"
(12.7)
5"
(12.7)
3 1/2"
(9.0) 3 1/2"
(8.9)
NOTES
STANDARD INSTALLATION
Product Specification Created 7/14
ZIC360NHLHGE Monogram®36" Built-In Bottom-freezer Refrigerator
AMounting the junction
box in this location will
also allow for front
accessability through
access panel.
BWater supply area.
WARNING:
The refrigerator is top
heavy and must be secured
to prevent the possibility of
tipping forward. Failure to
do so may result in death
or serious injury.
The information below is
for cabinet design only.
When installing the anti-
tip system you must use
the product installation
instructions.
The information below
applies to all installation
constructions:
• A wall bracket, bolts and
toggles will be supplied
with the unit.
• The bolts will be used to
attach bracket to wall in
4 locations. Two of the
locations must penetrate
the center of the wall
studs.
• The toggles are used for
stability in drywall and
when metal studs are
encountered. Lag bolts
are used in wood studs.
• In installation opening,
measure 81 ½” from
floor and draw a
horizontal line.
• Locate and mark the wall
studs on horizontal line.
Verify at least two studs
have their centerlines
within the center 32.5”
of installation opening to
ensure 2 wall studs are
penetrated.
• The bracket will be
centered left to right in
opening with bottom of
bracket on the horizontal
line.
• When unit is placed in
opening, the bracket tabs
will align with openings
in back of the unit. The
unit will be secured to the
bracket using supplied
“L” bolts.
See Installation
Instructions for detailed
instructions.
A
STANDARD INSTALLATION
ANTI-TIP BRACKET
24" (61.0)
1 1/2"
(3.8)
3"
(7.6)
7/16" (1.1)
Trim overlap
35 1/2" (90.2)
2 5/16"
(5.9)
SIDE VIEWFRONT VIEW
ZIC360NXRH
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
ELEC. 6"
(15.2)
10"
(25.4)
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
81 1/2"
(207.0)
WATER
5"
(12.7)
5"
(12.7)
3 1/2"
(9.0)
WATER
10" (25.4)
Use two
additional hole
locations at end
of brackets
Wall
Studs
Bracket
mounted
into vertical
wall studs
centered
within the
cutout
C
Ensure holes
selected are
centered on
the studs
L
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET

PANEL ASSEMBLY CROSS SECTION
PANEL ASSEMBLY CROSS SECTION
PANEL DIMENSIONS
PANEL DIMENSIONS
.25" + .10" + .75" = 1.10" Total Panel Thickness
NOTES
STANDARD 3/4" OVERLAY PANEL DIMENSIONS SINGLE INSTALLATION
STANDARD 1/4" FRAMED PANEL DIMENSIONS SINGLE INSTALLATION STANDARD INSTALLATION
Product Specification Created 7/14
ZIC360NHLHGE Monogram®36" Built-In Bottom-freezer Refrigerator
Trimmed refrigerators are designed to be
customized with decorative panels. Field-
installed custom door and grille panels are
required.
1/4” Framed Panels:
Order trim kit #ZTKBFHLH
for 1/4" thick custom panels ordered from
your cabinet maker. The decorative panels
slide into the trim.
Maximum total panel weight:
• Fresh food door panel – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 11 lbs.
A B C D
1/4" Framed Panel 33 7/8" 8 7/8" 46 1/16" 21 7/8"
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
B
C
D
Door
1/4" Framed Panel
Supplied Handles
Trim
A B C D
1/4" Backer Panel 33 7/8" 8 7/8" 46 1/16" 21 7/8"
.10" Spacer Panel 32 1/2" 7 5/8" 44 11/16" 20 1/2"
3/4" Overlay Panel 34 1/8" 9" 46 5/16" 22"
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
B
C
D
Door 1/4" Backer Panel
.10" Spacer Panel
Supplied Handles
Trim
3/4" Overlay Panel
3/4” Overlay Panels:
Order trim kit #ZTKBFHLH
for 3/4" thick custom panels ordered from
your cabinet maker. The decorative panels
slide into the trim. The overlay panel must be
secured to a 1/4"-thick backer panel which
slides into the trim. A spacer panel 0.10" thick
must be placed between the overlay and
backer panels.
Center each panel over the other. Assemble
the panels with glue and screws. Screws must
be countersunk into the backer panel.
NOTE: Left-to-right offset is not always equal
to top-to-bottom offset.
Maximum total panel weight:
• Fresh food door panel – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 11 lbs.
Door Handles:
The supplied handles can be adjusted to
accommodate both framed or overlay panels.
Custom handles of your choice, supplied by
your cabinet maker, can also be installed.
ZKHPSS1: Professional Tubular Stainless Steel
Handle designed to fit 3/4" overlay panels.
ZKHCSS2: European tubular handle designed
to fit 3/4” panels. Kit includes 2 handles.
Door handle is 44 3/16” and drawer handle
is 33 3/16".

Product Specification Created 7/14
ZIC360NHLHGE Monogram®36" Built-In Bottom-freezer Refrigerator
NOTES
FSide panels must be
used whenever the sides
of the refrigerator will
be exposed. The 1/4”
side panels will slip
into the side case trim.
Secure the panels to
the refrigerator with
stick-on hook and loop
fastener strips. Order
the side panels from the
cabinet manufacturer.
CUSTOM SIDE PANELS
F
2 9/16"
(6.5)
*3" - 4"
(7.6 - 10.2)
*Depending
on installation
height
1 7/8"
(4.8)
24" (61.0)
3/16"
(.5)
*84”
(213.4)
*Depending
on installation
*84"
(213.4)
*Depending
on installation
height
ZIF360NXLH_ZIF360NXRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH
ZIR360NXLH_ZIR360NXRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH
STANDARD INSTALLATION

NOTES
STANDARD INSTALLATION
Product Specification Created 7/14
ZIC360NHLHGE Monogram®36" Built-In Bottom-freezer Refrigerator
STANDARD 3/4" OVERLAY PANEL DIMENSIONS DUAL INSTALLATION
STANDARD 1/4" FRAMED PANEL DIMENSIONS DUAL INSTALLATION
PANEL DIMENSIONS
1/4"
Framed
Panel
A69 7/8"
B8 7/8"
C46 1/16"
D21 7/8"
E33 7/8"
PANEL ASSEMBLY
CROSS SECTION Door
1/4" Framed Panel
Supplied Handles
Trim
PANEL ASSEMBLY
CROSS SECTION
PANEL DIMENSIONS
1/4"
Backer
Panel
.10"
Spacer
Panel
3/4"
Overlay
Panel
A69 7/8" 68 1/2" 70 1/8"
B8 7/8" 7 5/8" 9"
C46 1/16" 44 11/16" 46 5/16"
D21 7/8" 20 1/2" 22"
E33 7/8" 32 1/2" 34 1/8"
.25" + .10" + .75" =
1.10" Total Panel Thickness
Door 1/4" Backer Panel
.10" Spacer Panel
Supplied Handles
Trim
3/4" Overlay Panel
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
Fresh
Food
Panel
Freezer Drawer Panel
E
B
C
D
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
Fresh
Food
Panel
Freezer Drawer Panel
E
B
C
D
Trimmed refrigerators are designed to be
customized with decorative panels. Field-
installed custom door and grille panels are
required.
1/4” Framed Panels:
Order trim kit #ZTKBFHLH for 1/4" thick
custom panels ordered from your cabinet
maker. The decorative panels slide into
the trim.
Maximum total panel weight:
• Fresh food door panel – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 25 lbs.
Order ZUG2: Unified grille kit for dual
installation
3/4” Overlay Panels:
Order trim kit #ZTKBFHLH for 3/4" thick
custom panels ordered from your cabinet
maker. The decorative panels slide into
the trim. The overlay panel must be secured
to a 1/4"-thick backer panel which slides
into the trim. A spacer panel 0.10" thick must
be placed between the overlay and backer
panels.
Center each panel over the other. Assemble
the panels with glue and screws. Screws must
be countersunk into the backer panel.
NOTE: Left-to-right offset is not always equal
to top-to-bottom offset.
Maximum total panel weight:
• Fresh food door panel – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 25 lbs.
Order ZUG2: Unified grille kit for dual
installation
Door Handles:
The supplied handles can be adjusted to
accommodate both framed or overlay panels.
Custom handles of your choice, supplied by
your cabinet maker, can also be installed.
ZKHPSS1: Professional Tubular Stainless Steel
Handle designed to fit 3/4" overlay panels.
ZKHCSS2: European tubular handle designed
to fit 3/4” panels. Kit includes 2 handles.
Door handle is 44 3/16” and drawer handle
is 33 3/16".

NOTES
STANDARD INSTALLATION
Product Specification Created 7/14
ZIC360NHLHGE Monogram®36" Built-In Bottom-freezer Refrigerator
71 1/2" (181.6)
Finished Width
24" (60.9)
Min. Cutout Depth
24 3/16" (61.4)
2 5/16"
(5.9)
6"
(15.2)
10"
(25.4)
83 1/2" min
84 1/2" max
(212.1-214.6)
Finished Opening
ZIC360NXLH_ZIC360NXRH_ZICP360NXLH_ZICP360NXRH
ZICS360NXLH_ZICS360NXRH
FRONT VIEW
ELEC. 6"
(15.2)
10"
(25.4)
3 1/2"
(8.9)
25" min
(63.5)
To wall
25" min
(63.5)
To wall
1"
(2.5)
130˚
Door swing 130˚ Door swing
75"
(190.5 )
From floor
to bottom
of electrical
area
ELEC.
SIDE VIEW
5"
(12.7) 5" (12.7)
WATER
10" (25.4)
WATER
3 1/2"
(9.0)
WATER
3 1/2"
(9.0)
5 3/4"
(14.6) 5 3/4" (14.6)
AA separate 115V, 60Hz, 15- or 20-amp
power supply is recommended for each
product.
Additional cutout width may be required when
side panels are used.
BIn a side-by-side installation of a left-
and-right-hand door swing product, 1”
clearance between the units is required.
Order ZUG2: custom panel unified grille kit for
one continuous grille panel.
DUAL PRODUCT CLEARANCES
DUAL INSTALLATIONS
71 1/2" (181.6)
Finished Width
24" (60.9)
Min. Cutout Depth
24 3/16" (61.4)
2 5/16"
(5.9)
6"
(15.2)
10"
(25.4)
83 1/2" min
84 1/2" max
(212.1-214.6)
Finished Opening
ZIC360NXLH_ZIC360NXRH_ZICP360NXLH_ZICP360NXRH
ZICS360NXLH_ZICS360NXRH
FRONT VIEW
ELEC. 6"
(15.2)
10"
(25.4)
3 1/2"
(8.9)
25" min
(63.5)
To wall
25" min
(63.5)
To wall
1"
(2.5)
130˚
Door swing 130˚ Door swing
75"
(190.5 )
From floor
to bottom
of electrical
area
ELEC.
SIDE VIEW
5"
(12.7) 5" (12.7)
WATER
10" (25.4)
WATER
3 1/2"
(9.0)
WATER
3 1/2"
(9.0)
5 3/4"
(14.6) 5 3/4" (14.6)
A
B

FEATURES AND BENEFITS
Product Specification Created 7/14
ZIC360NHLHGE Monogram®36" Built-In Bottom-freezer Refrigerator
Custom Appearance - Allows personalization
with cabinet-compatible panels an custom
handles
Upfront Electronic Controls with Digital Readout
- Allows precise temperature settings and are
positioned for maximum ease of use
Humidity Controlled Vegetable Compartments
and Sealed Snack Pans - Help maintain freshness
and help preserve foods longer
Adjustable, Spill Proof Glass Shelves - Make it
easy to customize storage to handle foods and
containers of various sizes
2 Sealed Deli Pans with Full-Extension Slides
Six Adjustable Door Bins - Offer added storage
flexibility
GE Water™Filtration System - Delivers clean,
great tasting ice
R