GE Monogram ZIK30GNZAII User manual

Design Guide with
Installation
Instructions
30" Built-In
Bottom-Freezer, 2-Dr(]wer
Refrigerator
monogram.com

SafetyInformation
BEFORE YOU BEGIN
Read these instructions completely and carefully.
.IMPORTANT- Savetheseinstructions
for local inspector's use. Observe all governing codes
and ordinances.
. Note to Installer - Be sure to leave these
instructions with the Consumer.
. Note to Consumer - Keep these instructions
with your Owner's Manual for future reference.
.Skill Level - Installation of this refrigerator requires
basic mechanical, carpentry and plumbing skills. Proper
installation is the responsibility of the installer. Product
failure due to improper installation is not covered under
the GEAppliance Warranty. See the Owner's Manual for
warranty information.
For Monogram local service in gour area, call
1.800.444.1845.
For Monogram Parts and Accessories, call
1.800.626.2002.
www.monogrom.com
WARNING:
This appliance must be properly grounded.
See "Grounding the Refrigerator," page 5.
If you received a damaged refrigerator, you should
immediately contact your dealer or builder.
A CAUTION:
Due totheweightand sizeofthisrefrigerator,and to
reducetheriskofpersonalinjuryordamage tothe
product-TWO PEOPLE ARE REQUIRED FOR PROPER
INSTALLATION.
AWARNING:
. Theserefrigeratorsoretop-heavyand must
be securedtopreventthepossibilityoftipping
forward.Anti-tipprotectionisrequired.See page 14
for details.
. Use this appliance only for its intended purpose.
. Immediately repair or replace electric service cords
that become frayed or damaged.
. Turn off the circuit breaker to disconnect power
before cleaning or making repairs.
. Repairs should be mode by a qualified service
technician.
AWARNING-R6ooa Refrigerant
Warning: This appliance contains isobutane refrigerant,
R6OOa,a natural gas with high environmental
compatibilitg. However it isalso combustible. Please
adhere to the warnings below:
i} When handling, installing and operating the appliance,
care should betaken to avoid
damage to the refrigerant tubing.
21Servicing shallbe performed by factory-authorized service
personneland component parts shall be replaced with
manufacturer-authorized replacement components.
:3)Refrigeration products contain refrigerants, which
under federal law must be removed prior
to product disposal.
41Keepventilation openings inthe appliance enclosuresor
in the built-in structure clearof obstruction.
51Donot usemechanical devicesor other means
to accelerate the defrosting process.
61Donot damage refrigerant circuit.
71Donot useelectrical appliances insidethe
food storage compartment of the appliance.
CONTENTS
Design Guide
Cabinet Enclosure Dimensions ............3
Refrigerator Dimensions..........................4
The Installation Space..............................5 Step
Grounding the Refrigerator ....................5 Step
Dimensions and Clearances..................3 Step
Integrated Handles Step
!15 ° Door Swing ........................................6 Step
Integrated Handles Step
90° Door Swing............................................7 Step
Professional Handles Step
!!5 ° Door Swing ........................................8 Step
Professional Handles Step
90° Door Swing............................................9 Step
SSPanel Accessory & Dimension ....!0
3/4" Custom Panel Dimensions ........!!
Installation Instructions
Tools, Hardware, Materials ..................12
Step 1, Remove Packaging ..................13
2, Install Anti-tip Bracket............14
3, Connect Water Line ................1/4
4, Connect Power ..........................1/4
5,Slide Unit into Enclosure ......15
6, Remove Toekick and Vent....15
7, Level Refrigerator ....................16
8, Install Toekick and Vent ........16
9, Reverse Door Swing ........17, 18
10,Adjust Door Swing ................18
11,Attach Hinge Guard ..............18
12, Install Door and Drawer
Panels..........................................19
Step 13, Start Icemaker ........................20
Badge Templates ....................................2]
Notes ......................................................22, 23

Design Guide
Cabinet Enclosure Dimensions For Fullg Integrated Instructions
25" min. depth _ YO"Finished Width
Height options
80" or *84"
The cutout depth must be 25"for
flush installations.
, Thefront face of the refrigerator fits
flush with 25"depth adjacent
cabinets.
, The refrigerator can fit into a 79-1/2"
minimum,
84-1/2" maximum high enclosure.
Although the refrigerator itself can
only be raised to 80 3/8",
, Thefresh food door pGnel can be
constructed to fill additional height;
see page 10.
Design Tip: We recommend finishing the inside surface of the enclosure clmin. of 4" from the front face.
'0L Design Tip: If using 84" enclosure, consider Gdding Gfinished vGlence Gbove the refrigerGtor cGse.
Design Tip: It is possible to align your refrigerator drawer with adjacent cabinetry for clcompletely integrated
look.
3

Design Guide
Refrigerator Dimensions with 3/4" Panels
Case
Door
Jk
Height adjustable
from
79-3/8" to 80-3/8" *
_Top with Panels
II •
<-_ 29 1/2" _
Front with Panels
23 37'4'(Case and Door only)
Panel
Side with Panels
Clearance
11
* The Refrigerator can be adjusted to fit into a cabinet space that is 83-3/8" to 84-
3/8" with the appropriate door panel kit.
install Clearances
Top Each Side Rear
1/8"/3mm 1/4"/6mm 1/2"/12mm
4

Design Guide
THE INSTALLATION SPACE
Water and Electrical Locations
Electrical and water supply should be located in shaded area only as shown.
PREPARINGINSTALLWATERLINE
,A cold water supply is required
for automatic icemaker operation. The water pressure must be
between 40 and 120 p.s.i.
, Route 1/4" OD copper or GESmartConnect T"plastic tubing between
the house cold water line and the water connection location.
,Tubing should be long enough to extend to the front of the
encloasure.
,Water line can enter an opening through the floor or back wall.
,Install a shut-off valve between the icemaker water valve and cold
water supply in the home.
NOTE:
. It is recommended that the water shut-off valve be placed in a
location that is easily accessible. We do not advise placing it behind
the unit because of access difficulties. If it is necessary to install the
valve behind the unit, it must be located in the shaded area.
, Saddletype shut-off valves are included in many water supply kits,but are
not recommended for this application.
,The only GE-approved plastic tubing is supplied in the GE
Anti-Tip location. Do
not obstruct this area. _'\ \\\
l m
80"
77"
+
Front view
Install Space
Water and Electrical
Tube Outlet _/
SmartConnecf" Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under
pressure at all times. Other types of plastic may crack or rupture with age and cause water damage to your home. GE
SmartConnecf" Refrigerator Tubing Kits are available in the following lengths:
6'(1.8m) W×08×10006, 15'(4.6m) WXO8XIO01S & 25'(7.6m) WXO8X10025
,Commonwealth of Hassuchusetts PlumbingCodes 248CHRshall be adhered to. Saddlevalvesare illegaland use is not
permitted in Massachusetts.Consultwith your licensed plumber.
Electrical Specifications
, A Z]_5-volt,60-Hz., Z5- or 20-amp power supply isrequired. An individual properly grounded branch circuit or circuit
breaker is recommended.
, Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear
wall as shown.
NOTE:GFI(ground fault interrupter)is not recommended.
GROUNDING THE REFRIGERATOR
IMPORTANT--(Please read carefullg)
FOR PERSONAL SAFETY,THIS APPLIANCE MUST BE
PROPERLYGROUNDED.
The power cord of this appliance is equipped with
a :3-prong (grounding) plug which mates with a
standard three-prong (grounding) wall receptacle
to minimize the possibility of electric shock hazard
from this appliance.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
Where a standard 2-prong wall outlet is encountered, it
isyour personal responsibility and obligation to have it
replaced with a properly grounded :3-prong wall outlet.
DO NOT,UNDERANY _I_ m]
CIRCUMSTANCES,CUT
OR REMOVETHETHIRD
(GROUND)PRONGFROM
THE POWERCORD.
DO NOT USEAN ADAPTER PLUG TO CONNECT THE
REFRIGERATORTO A 2-PRONG OUTLET.
DO NOT USEAN EXTENSION CORD WITH THIS
APPLIANCE.
5

Design Guide
Product Clearances
These refrigerators are equipped with a 2-position door
stop. Thefactory-set 115°door swing can be adjusted to
90° if clearance to adjacent cabinets or walls is restricted.
For90° Door swing see page 7.
Refrigerator
Allow 15"minimumclearance
for a full 115° doorswing.
ffff1" 3/4"
1-1/4"
1-1/2"
3/4"
I "
1-1/4"
1-1/2"
SS European or Custom Panels
Top View
115 ° DOOR SWING Not to scale
(factor settin )

Design Guide
Refrigerator ....................For a 90 ° door
swing allow 5" min.
clearance to a wall,
for stainless steel
models.
1/8"
2-I/4" 1-1/2" 1-1/4"
3/4"
I"
©1-1/2"
SS European or Custom Panels
Top View
90 ° DOOR SWING
Ioptional setting} Not to scale

Design Guide
Product Clearances
These refrigerators are equipped with a 2-position door
stop. Thefactory-set 115° door swing can be adjusted to
90° if clearance to adjacent cabinets or walls is restricted.
For90° Door swing see page 9.
Refrigerator
Allow 15"minimumclearance
fora full 115°doorswing.
©
Not to scale
SS Professional Panels
Top View
115 ° DOOR SWING
(factory setting)
8

Design Guide
Refrigerator
For a 90° door
swing allow 5" min.
clearance to a wall,
for stainless steel
models.
2-9/16"
SS Professional Panels
Top View
90 ° DOOR SWING
(optional setting}
Not to scale

Design Guide
SS PANEL ACCESSORY &DIMENSIONS
3/4"-Thick Solid Door Panel Options
For 80" High Installation
. Integrated - Panel Model ZKST3OON LH & RHcapable
. Professional - Panel Model ZKSP3OONLH& RH capable
For 84" High Installation (Thedoor panel is not
reversible for the 84" Installations. A left or right-hand
door panel accessory must be purchased.)
. LH Integrated - Model ZKST304NLH
. RH Integrated - Model ZKST304NRH
. LH Professional- Model ZKSP304NLH
. RH Professional - Model ZKSP304NRH
NOTE:Each kit also contains matching freezer and
customizable drawer panels, handles and toekick.
3/4"-Thick Frame for Glass Door Options
For 80" High Installation
. Integrated - Model ZKGT3OON LH& RH capable
. Professional- Model ZKGP3OON LH& RH capable
For 84" High Installation (Thedoor panel is not
reversible for the 84" Installations. Aleft or right-hand
door panel accessory must be purchased.
. LH Integrated - Model ZKGT304NLH
. RH Integrated - Model ZKGT304NRH
. LH Professional - Model ZKGP304NLH
. RH Professional - Model ZKGP30/4NRH
NOTE:Each option also contains matching freezer and
Convertible drawer panels, handles and toekick.
Cabinets
4"
I_ 29-3/4" _
Fresh
Food
IceDrawer
Freezer/
Convertible
Drawer
45-3/8" for 80" Installation
49-3/8" for 84" Installation
7-1/2"
t
22-3/4"
1/8" Min._
_Theremustbea minimum1/8"gapbetweenpanelsand
surroundingcabinetry.
29-3/4"_1
23"_
GlassPanel
for FreshFood Install Install.i
4s-318"
49-3/8"
_Pr0stylewindow isslightlysmaller..
Optional Accessorg Kits #:
. Side-by-Side Installation Kit - ZUG30
. European handle kit - (3 handles) - WR12X10988
(can be purchased through GE Parts)
10

Design Guide
3/4" CUSTOM PANEL DIMENSIONS: 80" High Fullg Integrated Installation
If you choose to install custom panels, they must be cut to
the dimensions shown. The panels will attach to the door
and drawers using a hook and bracket system.
EXTREMELYIMPORTANT: Custom wood panels must be at
least 3/4" thick where hooks and bracket hardware are
attached. Refer to Templates for hook and bracket location.
PANELSFORSOLIDDOORANDDRAWERS
29-3/@
A
45-3/8"
22-3/4"
NOTE:
PANELSFORGLASSDOOR
29-3/4"
This product is designed to handle 3A"panels that
ore made of wood.
33-3/8" x 23" isthe maximum opening for a glass
window. The opening may be smaller if desired.
IMPORTANTNOTE:Maximumpanelweight:
A FreshFoodDoorPanel:33 Ibs.
B FreezerDrawerPanel:9 Ibs.
I1ConvertibeDrawerPanel:19Ibs.
33-3/8"
6"
.. 3.3/8" _Stylesmustbea min 3-3/8"to coveraluminum
doorframe.
Design Tip:Someamountof eachpanelwill bevisibleontheinteriorside
ofthe unit.It is recommendedthat bothsidesof eachpanelbefinished.
Design Tip: If usingcustompanels,a cutomtoe kickshouldbeconsidered.
TheBottomof caseiswhite.
3/4" CUSTOM PANEL DIMENSIONS: 84" High Fullg Integrated Installation
If you choose to install custom panels, they must be cut to
the dimensions shown. The panels will attach to the door
and drawers using a hook and bracket system.
EXTREMELYIMPORTANT: Custom wood panels must be at least
3/4" thick where hooks and bracket hardware are attached.
Refer to Templates for hook and bracket location.
NOTE: this product is designed to handle 3A"panels that
ore made of wood.
33-:S/8"x 23" is the maximum opening for a glass
window. The opening may be smaller if desired.
PANELSFORSOLIDDOORAND DRAWERS
I_ 29-3/4"
49-3/8" A
7-i/2"
22-3/4"
4_,
PANELSFORGLASSDOOR
I._29-3/4"_ I
49-3/8"
3-3/8"_1
33-3/8"
_3-3/8'
IMPORTANTNOTE:Maximumpanelweight:
A FreshFoodDoorPanel:33 Ibs.
B FreezerDrawerPanel:9 Ibs.
I1ConvertibleDrawerPanel:19Ibs.
_Stylesmustbe a min3-3/8" to cover
aluminumdoorframe.
Design Tip: Someamountof eachpanelwill bevisibleonthe interiorsideof
theunit. It is recommendedthat bothsidesofeachpanelbefinished.
Design Tip: If usingcustompanels,a cutomtoeI<ickshouldbe considered.The
Bottomofcaseiswhite.
11

Installation instructions
TOOLS REQUIRED
.5/:32" Allen wrench
Utility knife
. Stepladder
. Bucket
. Level
. Appliance hand truck
. Tubing cutter
.7/16" open-end wrench
.1-5/16" open-end wrench
. #2 Phillips screwdriver
. Drill and bit set
.5/16" socket
. Safety glasses
. Pliers
.5/8" ratchet
.Torx T-20, T-Z0 wrench
HARDWARE SUPPLIED
. Anti-tip bracket & screws
. Panel mounting brackets
. Door panel templates- Pub # 31-46543
. Water filter - Part # GSWF
. Drywall Anchors and screws
MATERIALS REQUIRED
.1/4" copper water line tubing or GESmartConnect TM
Refrigerator Tubing kits
. Water shut-off valve
. Custom panels for fresh food door, freezer drawer
and Convertible drawer
. Velcro w/adhesive if using custom toekick.
FLOORING
For proper installation, this refrigerator must be
placed on a level surface of hard material that is at
the same height as the rest of the flooring. This
surface should be strong enough to support (] fully
loaded refrigerator, or approximately 1,200 Ibs.
NOTE:Protect the finish of the flooring. Cut u large
section of the cardboard carton and place under
the refrigerator where you are working.
12

Installation instructions
STEP 1 REMOVE PACKAGING
CAUTION: THE REFRIGERATOR IS
TOP-HEAVY. BE CAREFUL WHEN MOVING.
,Cut bands and tape on the top and bottom
of packaging with a utility knife.
, Unfold the cardboard seams and remove the top
of the packaging.
Slide the remainder of the box off of the appliance.
You can use a box cutter to cut the remaining
cardboard being VERYCAREFULnot to scratch
the appliance.
Remove the Styrofoam supports from around the unit.
. DO NOT remove door band or lower EPSbanded
part until unit is ready to go into enclosure.
,Cut EPSskid at the sides near the front from the back
of the unit.
, Push unit forward & remove rear portion of the EPS
skid.
, Carefully lower rear onto the floor.
, Lean unit back slightly & remove front portion of the
EPSskid.
, Discard all unused packaging materials appropriately.
, The unit can now be moved using an appliance hand
truck or rolled on a properly protected floor by 2
people.
, Leave any protective film on the refrigerator until
installation is complete.
13

Installation instructions
ISTEP 2 i INSTALL ANTI-TIP BRACKET
. InsideTop Faceof bracket should be installedat 80"
"Slot"in bracket should to be placed in center of install
Space(Typically!5")
. Mark (within slots, placement)stud and anchor positions
on brackets.
Slot
qI
• Securebracket usfng combination of studs & anchors.
.At least 1 stud must be engaged.However, pleaseengage
as many studs aspossiblewithin the enclosure.A mininum
of three fasteners should be usedfor proper installation.
[STEP 3 ICONNECT WATER LINE
. Position appliance in front of enclosure.
. Locate and bring tubing to the front of the cabinet.
. Turn the water on to flush debris from line. Runabout
a quart of water through tubing into a bucket; then
shut off water.
If needed cut the tubing to the proper length so it can
be attached to the water valve.
Copper Tubing:
. Slip a 1/4" nut and ferrule over both ends
of the copper tubing. Insert tube into the union fitting
on the unit and tighten nut to union.
. Turn on the water to check for leaks.
GESmartConnect TM Tubing:
. Insert the end of the tubing into the refrigerator
connection. Tighten the compression nut until it isjust
hand-tight.
. Tighten one additional turn with a wrench.
Overtightening can cause leaks!
. Turn on the water to check for leaks.
STEP 4 CONNECT POWER
e
e
Plug the power cord into the socket.
Check to make sure power to refrigerator ison by
opening the ice drawer (FFdoor will be banded shut)
to see if interior lights are on.
. The temperature controls are preset at 37°F for the
fresh food section and 0°F in both the freezer drawer
and customizable drawer.
. Allow 2/4hours to stabilize before making
adjustments.
14

Installation instructions
STEP 5 SLIDE UNIT INTO ENCLOSURE
Rollthe unit into the enclosure, being careful not to pinch
the water line or power cord.
, A long flat bar or yard stick may be needed to guide the
front edge of the anti-tip bracket over the unit.
, If space allows, you may also bend the front edge of the
bracket upward slightly, allowing it to clear the back of
the unit.
li
, Remove Top-Center trim cover from unit.
Secure the unit to the Anti-tip bracket using both
machine screws & washers to engage the threaded
inserts in the anti-tip bracket.
Hand start the screws until unit is in desired location
within the install space.
Finalize unit install by tighening the screws fully.
Reinstall Trim cover.
[STEP 6 I REMOVETOEKICKAND VENT
The toekick must be removed to access
the leveling leg system.
Remove band (]round EPSblock in front of toekick.
Remove and dispose of EPSblock.
Removethe solid portion of the toekick by pulling forward.
Placethe toekick,vent and screws out of the way soyou
will havethem for reinst(]ll(]tion.
Vent
Screws
(behind
t0ekick)_--_.
Screw/X
/Vent% ew
_L_ T0el<icl<
15

Installation Instructions
STEP 7 LEVEL REFRIGERATOR
All models have 4-point leveling. The front is supported
by leveling legs; the rear is supported by adjustable
wheels. Both are accessible from the front of the
refrigerator.
, To level the back of the refrigerator, turn the 5/16" hex
nut located above the front wheels. Turn counter
clockwise to raise or clockwise to lower the
refrigerator.
, For front leveling, use a 1-5/16" open-end wrench.
Adjust height of refrigerator to match installation
cutout opening. The refrigerator should be level and
plumb with cabinetry.
up\
HexNut
AdjustsRear
Wheels
<
_q
LevelingLeg
CAUTION:
The rear leveling wheels and front leveling legs are
limited to a maximum height adjustment of 1". If the
installation requires more than 84-1/2" height, the
installer should elevate the refrigerator on a sheet
of plywood or runners. Cabinetry trim could also be
added across the top of the opening to shorten the
opening.
If gou attempt to raise the refrigerator more than i",
gou will damage the front leveling legs and the rear
leveling wheels.
STEP 8 INSTALL TOEKICK AND VENT
, Locate the toekick, vent and screws (removed earlier).
, A custom toekick can be installed to match or
complement the surrounding cabinetry. Use the
supplied toekick as a template.
, Reinstall the vent using the screws removed earlier.
, Reinstall the toekick. Toel<ickHoles
/
SuppliedT0ekicl<
16

Installation Instructions
STEP 9 IREVERSE DOOR SWING Ilfneeded}
Skip this step if door swing is satisfactorg.
1.Open the fresh food door.
A WARNING: THISNEXTSTEPIs
IMPORTANT FOR SAFE HANDLING OF AN
UNLOADED HINGE. DO NOT SKIP STEP 2.
2. Releosethe hinge springs by using o TorxT-20 wrench
to loosenthe Torx screw from I to 0 on both hinges.
Closethe door.
3. Using o5/32" Allen wrench, remove the 2 screws per
hinge thot secure the door to the refrigerator. Hove
someone hold the door while removing these screws
to keep the door from falling.
Screws
4. Open the hinges. Using o 5/32" Allen wrench, remove
the 2 screws per hinge that secure the hinge to the
refrigerator cabinet.
5. Removethe trim and hinge pocket from the top
ofthe refrigerator ond installon the opposite sides.
6. Removethe trim ond hinge pocket from the bottom
ofthe fresh food comportment. Removethe control panel
and gently place in the FZdrawer.
Control Ponel
7. Reinstallthe control panel.
17
STEP 9 REVERSE DOOR SWING Icont}.
8. The hinges will be reinstalled in opposite corners.
The hinge from the top will be turned over
and instolled at the bottom of the fresh food
comportment. The hinge from the bottom will be
turned over and installed at the top of the fresh food
comportment.
TopHinge BottomHinge
9. Install the screws on the fresh food comportment
cabinet in oil 4 places. Screw them in about halfway.
Screws Slotsfor
Tabs
10.To install the top hinge, turn the hinge in the proper
direction-the section of the bracket that will be
attached to the door should be ot the bottom of the
hinge. Slide the hinge over the screws and seat the
tabs into the hinge pocket. Tighten the screws.
Scr
11.To install the bottom hinge, turn the hinge in the
proper direction-the section of the bracket that will
attach to the door should be ot the top of the hinge.
Slide the hinge over the screws and seat the tabs
into the hinge pocket. Tighten the screws. Close
the hinge.
12.Removethe hinge brackets from the door and reinstall
them on the oppositeend,top and bottom.

Installation Instructions
jSTEP 9 REVERSE DOOR SWING (cont).
13.With another person holding the door in place,
align the holes in the door hinge bracket with the
holes in the hinge. Install the screws to the top
hinge first. __- Door
Screws
14.install screws on the bottom hinge next.
15. Using a Torx T-20 wrench, tighten the tension on
the hinge springs by turning the screws from 0 to I.
T-20Wrenc_
STEP 10 ADJUST DOOR SWING (if needed)
NOTE:This refrigerator has a 2-position door stop. When
space does not allow the door to swing to 1!5 °,you may
limit the door swing to a 90°
Skipthisstepifdoor openingis satisfactorgforgour
installation situation.
,Open the fresh food door to access the top and bottom
hinges.
. Loosen the bottom hinge screws that attached to the
unit
. Pull hinge forward slightly & insert hinge pin into the
hole nearest the unit.
,You may need to use a small hammer to fully seat
them in place.
, Retighten hinge screws.
, Repeat for top hinge.
iJ _ Install1 pin,
: .......... perhingefor
g0° doorstop.
Hingescrews
18
STEP 111 ATTACH HINGE GUARD
A WARNING:
This appliance must be installed & operated with the
hinge guard in place !
1.Attach hinge guard bysliding flat part between case
and adjacent cabinetry.
2. Fastenguard to door front using4 screws.
/ /

Installation instructions
[STEP 12 INSTALL DOOR AND DRAWER
PANELS
1. Removeall door and drawer hooks from the unit and
screw them to the custom panels, aligning them with the
lowest set of predrilled holesfor ivlonogram Panel Kitson
the FFdoor panel.
2.Attach top L-Bracketto FFpanel.
3. Ifyou had custom handles made and they (]re not
currently attached to your panels, do so now.
4.Open the fresh food door to attach the fresh food panel.
5.Slidethe hooks on the fresh food panel intothe slotsof the
door,and lower the hooks into place, ivlakesure the
bracket on the top of the panel slidesover the screw posts
on top of the door. Thebracketswill rest on top of the nuts.
Bracl(et _ -- ScrewPost
Hooks," --- Slots
Hooks on the Freezer
drawer panel face up.
]
F-
6. Adjust the screw posts up or down under the bracket
on top of the door to level the panel.
7. Lock the panel to the door by installing the nuts
provided onto the screw posts on top of the door.
Next, screw the L-bracket
the door and the panel. )rovided into the bottom of
ScrewPost
Hooks
Slots
Topof Brack_
FreshFood
PanelDoor
[STEP 12J INSTALL DOOR AND DRAWER
PANELS {cont).
7. Installthe Freezerdrawer panel bysliding the brackets
up into place (theopposite direction of the hooks on the
fresh food panel and Convertibledrawer)..
8. Oncethe drawer panel is placedfasten the panel to the
drawer byscrewing the bottom bracket into the panel
with the screws provided.
9. Repeatfor the second drawer by slidingthe hooks down
instead of up.
10. If usingcustom toekick attach the toekick panel by
placingVelcroon the buck of the panel,and on the fron
of the toekick.If using SStoekick it ismagnetic.
11.Adjust drawer alignment using lower brackets us
neededto create uniform gaps.
Freezer
Drawer
:i
Bracket
&A
Buck View of Panel Hooks and Bracket
Freezer
Drawer
Fresh
Food
Door Convertible
drawer
19
Thelowerbracketson theFreshFood& ConvertibleDrawer
shouldnotbe installeduntil afterthe panelis in place.

Installation instructions
[STEP 13 ISTART ICEMAKER
. Pressthe ZONE indicator on the control pad twice
to select the freezer drawer. Pressthe ICEicon on the
right side of the control. A line will oppear under ICEto
show that the icemoker is ON.
. Be sure nothing interferes with the sweep of the feeler
arm.
. Discord the first full bucket of ice cubes.
f_ nu, = +)
k_ u_
. To turn the icemoker off, press the ICE icon. The word
OFF appeors below ICEto show thot the icemoker
is OFF.
r_ (,- D.3_ I "_' iCEk,-u7 - +) ""_'"_
zo_
2O