GE Monogram ZISS480DXBSS User manual

Installation
Instructions
Side by Side Refrigerators
Design Guide
With Installation Instructions
31-46514-1 4
224D1889P01
01-13 GE
monogram,corn

Safety information
BEFOREYOU BEGIN
Read these instructions completely and carefully.
, IMPORTANT- Savetheseinstructionsfor
local inspector's use. Observe all governing codes and
ordinances.
, Note to Installer - Be sure to leave these
instructions with the Consumer.
• Note to Consumer - Keep these instructions with
your Owner's Manual for future reference.
WARNING:
This appliance must be properly grounded. See
"Grounding the Refrigerator," page 10.
AVERTISSEMENT
Cet appareil dolt _tre correctement mis 6 la terre.
Consultez <<Mise 6 la terre clu r6frig@ateur >>,page 10.
If you received a damaged refrigerator, you should
immediately contact your dealer or builder.
CAUTION:
Due to the weight and size of this refrigerator,
and to reduce the risk of personal injury or damage
to the product- THREE PEOPLE ARE REQUIRED
FOR PROPER INSTALLATION OF A 36" WIDE UNIT.
FOUR PEOPLEARE REQUIRED FOR INSTALLATION
OF A 42" OR 48" WIDE MODEL.
PRUDENCE
i cause du poids et de la taille de ce r6frig@ator
et pour r6duire le risque de blessure et de dommages,
IL FAUT TROIS PERSONNES POUR INSTALLER
CORRECTEMENT D'UN APPAREIL DE 91 cm (36 po)
DE LARGE. IL FAUT QUATRE PERSONNES POUR
L'INSTALLATION D'UN HODELE DE 107 OU 122 cm
(42 OU 48 po) DE LARGE.
Skill Level -Installation of this refrigerator requires
basic mechanical, carpentry and plumbing skills.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the GE Appliance Warranty.
See the Owner's Manual for warranty information.
WARNING:
o These refrigerators are top-heavy and must be
secured to prevent the possibility of tipping forward.
Anti-Tip protection is required. See page 12 for
details.
o Use this appliance only for its intended purpose.
Immediately repair or replace electric service cords
that become frayed or damaged.
, Unplug the refrigerator before cleaning or making
repairs.
, Repairs should be made by a qualified service
technician.
AVERTiSSEMENT
Ces r6frig@ateurs sont Iourds en haut et il faut les
arrimer pour 6viter leur basculement II faut avoir
un systeme de protection contre le renversement.
Voir les d6tails page 12.
II ne faut utiliser cet appareil que pour I'utilisation
appropri6e.
R6parer ou remplacer imm6diatement tout cordon
61ectrique effiloch6 ou endommag&
IIfaut d6brancher le r6frig@ateur avant le nettoyage
ou toute intervention.
Les r6parations cloivent _tre faites par un technicien
qualifi&
For Monogram local service in your area,
call 1.800.444.1845.
For Monogram service in Canada,
call 1.800.561.3344
For Monogram Parts and Accessories,
call 1.800.626.2002.
www,monogram,com
CONTENTS
Planning Guide
The Installation Space.......................................3
Dimensions and Clearances ..........................3
130 ° Door Swing ..................................................4
90° Door Swing.....................................................5
Customization Basics........................................6
1/4" Framed Panel Dimensions ....................7
3/4" Overlay Panel Dimensions ....................8
Raised Overlay Panel Design .........................9
Side Panels ..........................................................10
Installation Instructions
Tools, Hardware, Materials .........................10
Grounding the Refrigerator ........................10
Step 1,Remove Packaging .........................11
Step 2, Move Refrigerator into House ,,,11
Step 3, Install Water Line ......................11-1 2
Step/4, Household Water Filtration ........12
Step 5, Install Side Panels ...........................12
Step 6, Install Anti-Tip Brackets ................12
Step 7, Level Refrigerator ............................13
Step 8, Alternate Anti-Tip Procedure .....13
Step 9, Secure Refrigerator to Cabinetry, 14
Step 10, Adjust Door Swing ........................14
Step 11, Install Grille Panel .........................14
Step 12, Install Framed Panels .................15
Step 12A, Install Overlay Panels ........16-17
Step 13, Install Dispenser Trim...................18
Step 14, Connect Water Supply ...............18
Step 15, Connect Power ..............................19
Step 16, Start Icemaker ................................19
Step 17, tnstoll Toekick .................................19
ZKHSS2Tubular Handle Kit
Step 1,Remove Door Handles ..................20
Step 2, Install Handles onto Panels ........21
Step 3, Install Assembled Handles ..........22
Step/4, tnstoll Dispenser Trim ....................22

Design Guide
THE INSTALLATION SPACE
36" Models !.
42" Models !;
48" Models 2q
5" From FIo
to Bottom
of Electric(]
Are(]
*The finished cutout width must be;
35- 7/2" for 35" models
47- 7/2" for 42" models
47-1/2" for 48" models
Water And Electrical Locations
The opening must be prepared with the electrical
and the cold water supply located as shown.
The cutout depth must be 24"
The refrigerator will project forward, slightly beyond
adjacent cabinetry, depending on your installation.
Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot
exceed the 24" installation depth shown. The top case
trim overlaps the bottom of the soffit.
Additional Specifications
, A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install
a properly grounded 3-prong electrical receptacle
recessed into the back wall. Electrical must be
located on the Fear wall as shown.
NOTE: GFI (ground fault interrupter)is not
recommended.
, The water line can enter the opening through
the floor or back wall. The water line should be 1/4"
O.D. copper tubing or GE SmartConnect TM kit between
the cold water line and water connection location,
long enough to extend to the front of the refrigerator.
Installation of an easily accessible shut-off valve
in the water line is required.
DIMENSIONS AND CLEARANCES
"83-1/
at
Rea
25-3/8"FramedModels
35",41" or47" 25-3/4"StainlessSteel Models
VVidth
...................I Shippingheight,
i
Therefriger_Ror can
be adjusted to fit
into acutout that
is-83-1/2" min. to
_84"From 8q- 7/2" max. height.
Floorto
TopFrame Note that the top
case trim at the
f?ont is-7/2" higher
and will overk_p
upper cabinetry or
soffit. Use leveling
legs and wheels
for amaximum 7"
42"or48" height adjustmenL
Frameto Frame
DepthIncludingHandles:
26-7/8"FramedModels
27-3/4"StainlessSteelModels
28-11/16"ProfessionalModels
Product Clearances
These refrigerators are equipped with a 2-position door
stop. The factory-set 130 ° door swing can be adjusted
to 90 ° if clearance to adjacent cabinets or walls
is restricted.
730_"Door Swing gO_"Door Swing
%/
T
23-7/8"
Behind
Frame
C
Models A B C *Min. Distance
toWall
36" 73" 75" 20-5/8"
42" 73" 72" 26-5/8" _4"Stainless and
48" 75" 20" 28-5/8" #rimmed Models.
5" Pro Series
Allow minimum clearances for the freezer door
(Dimension A) and fresh food door (Dimension B)
for a full 130 ° door swing and to allow for pan removal.
For a 90° door swing, allow 4" min. clearance to a wall,
for framed and stainless steel models. Allow 5" min.
clearance for professional series models. If the 90° door
stop position is used, pan access is maintained, but pan
removal is restricted.
See the illustrations on pages 4 and 5 to determine door
swing interaction with adjacent cabinets or countertops.

Design Guide
Refrigerator 23-7/8"From
Rearof
Refrigerator
Case
Trim 3/4"
,_ 1/2" i
u
u
1/4" 'u
u
u
u
u
u
u
.In
m
Frameless Cabinets: The case trim overlaps
cabinets at the top and sides. Therefore,
frameless cabinets may require filler strips
to prevent interfeence with cabinet door
swing. The opening must allow for filler strips.
3/4" Overlay
Panel
(NominalSize)
Top View
130 ° DOOR SWING
(factory setting)
Scale 1:1
Door
i-1/4"
IMPORTANT NOTE -
FOR DISPENSER MODELS:
Dispenser models are supplied with two
dispenser trims, one to fit framed panels
and one for overlay panels. Dispenser trim
fit to the custom panel depends on correct
panel thickness. Framed panels must be
1/4" nominal. Overlay panels should be
constructed as shown to accomplish a total
1.100" thickness. See pages 7 and 8 for details.

Design Guide
Refrigerator
Top View
90 ° DOOR SWING
(optional setting)
Scale 1:1
IMPORTANT NOTE -
FOR DISPENSER MODELS:
Dispenser models are supplied
with two dispenser trims, one to fit
framed panels and one for overlay
panels. Dispenser trim fit to the
custom panel depends on correct
panel thickness. Framed panels
must be 1/4" nominal. Overlay
panels should be constructed as
shown to accomplish (_total 1.100"
thickness. See pGges 7 Gnd 8 for
details.
Door
_Case _im
Frameless Cabinets:
The case trim overlaps
cabinets at the top
Gnd sides. Therefore,
frameless cabinets may
require filler strips to
prevent interference
with cabinet door swing.
The opening must GIIow
for filler strips.
23-7/8"
FromRearof
Refrkerator
i u u
i u u
u i i
u
i u
,.---, .... _---, ..... 1/2"
u
i u u
i i
' 3/4"
1-1/2"
3/4"Overlay
Panel
(NominalSize)
1-1/4"

Design Guide
CUSTOMIZATION BASICS:
Framed Or Overlay Panels, Custom Handles and Accessory Kits
Professional Style Stainless Steel Refrigerators
Stainless steel wrapped refrigerators have beveled edges
and professional-style handles. These models are shipped
ready for installation,
Stainless Steel Wrapped Refrigerators
Stainless Steel wrapped refrigerators have wrapped doors
and grille panel, beveled edges, and tubular stainless steel
handles that coordinate with other Monogram appliances.
These models are shipped ready for installation.
Trimmed Refrigerators
Trimmed refrigerators are designed to be customized
with decorative panels, Field installed custom door
and grille panels are required,
Framed panels
You may install 1/4" thick custom panels from
your cabinet manufacturer. The decorative panel slides
into the factory installed trim. Order black or stainless steel
accessory panels from your Monogram dealer.
Framed Panel
I
Standard Door Handles
Overlay panels
You may also choose to install custom overlay panels from
your cabinet manufacturer. This design )rovides
a seamless appearance which integrates smoothly with
surrounding cabinetry.
// ,,
LJ
3/4" Overlay P/onel/1 J
.!!/04[Thhii:kk SBPa:_:[ Pp:::l Standard Door Handles
StP_nd_rd sup/Dried hc_ndles shown in 3/4" overl_y /Dc_ne/position,
Door Handles
The standard supplied handles can be adjusted to
accommodate both framed or overlay panels. Custom
handles of your choice, supplied by your cabinet maker
can also be installed on 3/4" overlay panels. If desired,
you may order ZKHSS2Monogram stainless steel
tubular handle kit for 3/4" overlay panels.
Side Panels
Side panels must be used whenever the sides
of the refrigerator will be exposed,
St_nd_rd sup/Dried hc_ndles shown in 7/4"/Dcme/position,
Optional Accessory Kits
ZKHSS2:Monogram Tubular Stainless Steel handles
designed to fit 3/4" overlay panels.
Accessory Panels
Black and stainless steel accessory panels are available
from your Monogram dealer. Panels are cut to size and
ready to install,
ZISW480D ZPS480D
ZISa80N ZPBa80N ZPSa80N
ZISB420D ZPB420D ZPS420D
ZISW360D ZPS360D
ZIS360N ZPB360N ZPS360N

Design Guide
1/4" FRAMED PANEL DIMENSIONS
If you choose to install framed panels, they must
be cut to the dimensions shown. The panels will slide
into the frame on the door and grille,
Non-Dispenser Models
If the custom panel is less than 1/4" thick and it fits
loosely in the door frame it can be backed up with
a piece of filler material or foam tape to improve
the fit,
Door
"'!75!!6"
Reveal
..............1!4"
Panel
IMPORTANT NOTE: M_ximum tariff panel weight;
Fresh food door panel -75 Ibs,
tFreezer door panel - 53 Ibs,
tGrille P_nel -78 Ibs,
IMPORTANT NOTE- DISPENSERMODELS
The refrigerator is supplied with two dispenser trims,
one for framed panels and one for overlay panels.
, If the panel is less than 0.250" thick, a noticeable gap
may be created around the dispenser trim. Foam
tape may be applied on the door to improve the fit.
, If the panel is more than 0.250" thick, the dispenser
trim cannot be secured to the door.
See Dispenser Trim Fit Example, page 9.
Grille Panel
U
F
)ispen se L
Cutout
Freezer Fresh
Panel Food
Panel
_D -_ _E_
Dispenser Cutout
The #amed panel must be 7/4" nominal
thickness to fit the dispenser trim,
Side-by-Side (in inches) !
36" Models 33-7/8 9 68-3/8 14-9/16 18-9/16
42" Models 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16
48" Models 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16 ............

Design Guide
3/4" OVERLAY PANEL DIMENSIONS
For a more custom appearance, overlay panels may
be installed on trimmed models. The overlay panel must
be secured to a 1/4" thick backer panel which slides
into the trim. A spacer panel 0.10" thick must be placed
between the overlay and backer panel.
Assemble the panels with glue and screws:
, Center the spacer panel on the backer panel, left to
right and top to bottom. Secure the panels with glue.
, Center the spacer and bucker panel on the overlay
panel and secure with glue and screws. Screws must
be countersunk into the backer panel.
Door
L
Backer .
Panel.......................Spacer
OverlaL
£ackerPanel
NOTE: Left-to-right offset is-
not nlwz_ys equn/ to top-to-
bottom off#eL
,250" +,70" +,750" - 7,7OO" Tote# P_nel Thickness
IMPORTANTNOTE -DISPENSERMODELS
The refrigerator is supplied with two dispenser trims,
one for framed panels and one for overlay panels. The
overlay dispenser trim is designed to fit a total panel
thickness of 1.100".
, If the panel is less than !.100" a noticeable gap may
be created around the dispenser trim.
, If the panel is more than !.100" the dispenser trim
cannot be secured to the door.
See Dispenser Trim Fit Example, page 9.
, The overlay panel must be constructed according to
the specifications shown to achieve the correct total
thickness.
, Alternative panel construction methods such as
securing a 3/4" panel to a 1/4" backer panel cannot
be used. Another method, routing a 3/4" thick panel
on all sides, cannot be used. These methods will not
result in the required 1.100" panel thickness.
When a raised panel design is to be used, a custom
middle rail is required. See page 9 for details.
A
GrillePanel B
U
F
)ispen se L
Cutout
Freezer Fresh
Panel Food
Panel
-- m
_D_4 _E_
Dispenser Cutout *Cut the dispenser opening after the backer, spacer and overlay
panels have been assembled,
IMPORTANT NOTE: Maximum total weight for the assembled
panels:
, Fresh food door panel - 75 Ibs.
Freezer door panel - 53 Ibs.
e Grille Panel- 18 Ibs.
36"Side-by-Side(ininches)
1/4" BackerPanel 33-7/8 9 68-3/8 14-9/16 18-9/16
.10"SpacerPanel 33 8-3/8 67 13-1/4 17-1/4
3/4" OverlayPanel 34-1/8 9-1/4 68-5/8 14-13/16 18-13/16
42"Side-by-Side(ininches)
1/4" BackerPanel 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16
.10"SpacerPanel 39 8-5/8 67 13-1/4 23-1/4
3/4" OverlayPanel 40-1/8 9-3/4 68-5/8 14-13/16 24-13/16
48"Side-by-Side(ininches)
1/4" BackerPanel 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16
.10"SpacerPanel 45 8-5/8 67 17-1/4 25-1/4
3/4" OverlayPanel 46-1/8 9-3/4 68-5/8 18-13/16 26-13/16

Design Guide
DISPENSER MODELS:
RAISED OVERLAY PANEL DESIGN
When a raised panel design is to be used,
a custom wide middle rail is required to accept
the dispenser trim.
, The middle rail must be wide enough to allow
for the dispenser trim to overlap the opening.
, The middle rail must be !.!00" total thickness
to accept the dispenser trim.
16-3/4"
i0-5/8:'- "_1
1!4" Backer Pan_4
.10" Spacer
3/4" Overlay Par_
Wide
Hiddle
Rail is
Required
DISPENSERTRIM FIT EXAMPLES:
(NOT TO SCALE)
1/4" FRAMED PANEL
, The dispenser trim fits over the custom
panel and snaps into the freezer door.
, The clips will not engage the door
if the panel is more than 0.250" thick.
, If the panel is less than 0.250" thick,
a noticeable gap may be created
around the dispenser trim.
3/4" OVERLAYPANEL
, The dispenser trim fits over the custom
panel and snaps into the freezer door.
, The clips will not engage the door
if the panel is more than !.!00" thick.
, If the panel is less than !.!00" thick,
a noticeable gap may be created
around the dispenser trim.
1/4" FREEZERDOOR 0250"
Framed Thick
I14" Backer Panel
.I0" Spacer
114" Dispenser Trim
FREEZERDOOR 1.100"
Total Thickness
3/4" Overlay Dispenser Trim

Design Guide
SIDE PANELS
Side panels must be used
whenever the sides of the
refrigerator will be exposed.
The !/4" side panels will
slip into the side case trim.
Secure the panels to the
refrigerator with stick-on
hook and loop fastener
strips. Order the side
panels from the cabinet
manufacturer.
, Cut a notch in the top
front corner as shown
to allow clearance for
corner keys in the front
side trim.
_84"
]_'3" to 4"
2-9/16"
* Depending on installation heighL
TOOLS AND MATERIALS REQUIRED
, Tinsnips to cut banding
, Stepladder
, !" Bit extenion
, Tape measure
, Gloves
, !/4" Drywall screws
,5-Gal. Bucket with cover
,6" Spirit level
, Appliance hand truck
, Tubing cutter
,7/16" open-end wrench
, #2 Phillips screwdriver
, Drill and appropriate bits
,5/!6", 7/!6" socket
, Safety glasses
, !-!/8" open end wrench
, Pliers
,1/4", 5/16" Combo Rachet
,35" long 2x4 for Anti-Tip support
, !/4" copper water line tubing or GE SmartConnect TM
Refrigerator Tubing kits
, Water shut-off valve
, Custom panels for doors and grille panel
, Screws to secure refrigerator to cabinetry
, Stick-on hook and loop fastener strips for
1/4" side panels
HARDWARE SUPPLIED
, Water filter bypass plug
, Anti-Tip brackets
,1/4" nut and ferrule
, Dispenser trims for 1/4" and 3/4" overlay panels
(for use with Custom Panel models).
, Aluminum cover trim for 3/4" overlay panels
with custom handles. Includes 22 flat head screws
and 4 endcaps.
FLOORING
For proper installation, this refrigerator must be placed
on a level surface of hard material that is at the same
height as the rest of the flooring. This surface should
be strong enough to support a fully loaded refrigerator,
or approximately 1,500 Ibs.
NOTE: Protect the finish of the flooring. Cut a large
section of the cardboard carton and place under
the refrigerator where you are working.
GROUNDING THE REFRIGERATOR
IMPORTANT - (Please read carefully)
FOR PERSONAL SAFETY,THIS APPLIANCE MUST
BE PROPERLYGROUNDED.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard :S-prong (grounding) wall receptacle
to minimize the possibility of electric shock hazard
from this appliance,
Have the wall outlet and circuit checked by
a qualified electrician to make sure the outlet
is properly grounded.
Where a standard 2-prong wall outlet is encountered,
it is your personal responsibility and obligation
to have it replaced with a properly grounded
3-prong wall outlet.
DO NOT, UNDER
ANY CIRCUMSTANCES,
CUT OR REMOVE
THE THIRD (GROUND) PRONG
FROM THE POWER CORD.
DO NOT USEAN ADAPTER PLUG TO CONNECT
THE REFRIGERATORTO A 2-PRONG OUTLET.
DO NOT USEAN EXTENSION CORD WITH THIS
APPLIANCE.
10

Installation Instructions
ISTEP1 IREMOVEPACKAGING
CAUTION:The refrigerator is much heavier at
the top than at the bottom-be carefulwhen moving.
When using a hand truck, handle from the side only,
PRUDENCE:Le r#frig#rateur est beaucoup
plus lourd en haut qu'en bas. IIfaut #tre prudent lors
des d#placements. Si un diable est utilis#, il faut soulever
le r#frig#rateur sur le c6t# seulement.
, Carefully cut banding at the top and bottom,
remove the outer carton.
, Slide out the back corner posts (2).
, Slide the carton off the top of the cabinet.
NOTE: IT IS NOT NECESSARY TO LAY THE CABINET DOWN
IN ORDER TO REMOVE THE SKID!
, The unit is secured to the skid with 4 slotted
tie-down straps. Remove the six 7/16" bolts
from the base channels in the tie-downs.
Q
Q
, Remove the six 7/16"
bolts securing the straps
to the skid.
CAUTION: DoNOT
ATTEMPT TO ROLL UNIT
OFF SKID,
Remov,
oow,PRUDENCE: ILNE
FAUT PAS ESSAYERDE FAIRE
_¢ ROULER LE REFRIGERATEUR
POUR L'ENLEVER DE LAY
PALETTE.
The support blocks on the bottom of the refrigeration
case must be removed before the refrigerator is
taken off the skid or damage will occur. Carefully
tilt the refrigerator and slide the blocks out from
beneath.
Remove the toekick and set aside for final installation.
Lift the refrigerator off the skid with an appliance
dolly. Handle from the sides.
[STEP2 MOVE THE REFRIGERATORINTO THE HOUSE
, Re-use the corner posts from the packaging to protect stainless steel models. Runthe appliance dolly straps over
the posts and under the handles.
, Leave the protective film on the refrigerator until installation is complete.
IMPORTANT:Never lift the refrigerator by the handle or push against the grill panel; this could cause damage
or misalignment.
, Avoid laying the unit on its back or side to prevent sealed system restrictions.
ISTEP31 INSTALL WATER LINE
, A cold water supply is required for automatic
icemaker operation. The water pressure must
be between 40 and 120 p.s.i.
, Route 1/4" OD copper or GE SmartConnect TM
plastic tubing between house cold water line
and the water connection location.
, The tubing should be long enough to extend
to the front of the refrigerator. Allow enough tubing
to accommodate the bend leading into the water line
connection.
NOTE: The only GE approved plastic tubing is supplied
in the GE SmartConnecf MRefrigerator Tubing kits.
Do not use any other plastic water supply line because
the line is under pressure at all times. Other types
of plastic may crack or rupture with age and cause
water damage to your home.
GE SmartConnecf _ Refrigerator Tubing Kits are
available in the following lengths:
2' (.6 m) WXO8XIO002
6' (1.8 m) WXO8XIO006
15' (4.6 m) WXO8X10015
25' (7.6 m) WXO8X10025
_Cold WaterLine
11

Installation Instructions
[STEP 3] (continued)
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the line
of water.
, Install a shut-off valve between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be
easily accessible.
, Turn on the main water supply and flush debris.
Run about a quart of water through the tubing into a
bucket. Shut off the water supply at the shut-off valve.
NOTE: Saddle type shut-off valves are included in many
water supply kits. Before purchasing, make sure a saddle
type valve complies with your local plumbing codes.
NOTE:Commonwealth of Hassachusetts Plumbing
Codes 248CHR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts,
Consult with your licensed plumber.
[STEP4 1INSTALLATION WITH
HOUSEHOLD WATER
FILTRATION SYSTEM
Skip this step if you do not have a household water
filtration system
If the water supply to the refrigerator is from
any household water filtration system, the filter
cartridge should be removed. For better ice and water
performance, remove the filter and install the filter bypass
plug,
Rotate Clockwise To Filter Bypass
Remove Plug
[STEP 5 INSTALL SIDE PANELS
Skip this step when not using side panels.
If you are using 1/4" side panels, they should
be inserted into the case trim. Fasten the panels
to the refrigerator with stick-on hook and loop
fastener strips before setting the refrigerator in place.
12
ISTEP6 1INSTALLANTI-TIPBRACKETS
WARNING: ANTI-TIPPRECAUTIONS
The refrigerator is top-heavy and must be secured
to prevent the possibility of tipping forward.
ATTENTION: PRECAUTIONS CONTRE
LES BASCULEMENTS
Le r#frig#rateur est beaucoup plus Iourd en haut
et il faut le maintenir en place pour #viter la possibility
de son basculement vers I'avant.
, Cut a 2" x 4" block, 35" long and secure the block
to the mounting brackets provided using #12 or #14
wood screws,
2x4Cut
35" Length ', ,_ ,_
l,'i ,'!
Installation Mounting-
Height Bracket
From Floor
Screws Mounted into M
Vertical Wall Studs
, Secure the bracket with wood block to the buck wall
so that it is 84" (or your installation height) from
the finished floor. Use #12 or #14 wood screws.
See the illustration,
Brackets I
Required
Brackets
Not Required
Beneath a
Soffit
SideView
, The screws must penetrate at least one inch
into the vertical wall studs.
Connect power cord:
, Before pushing the refrigerator into the opening, plug
the power cord into the receptacle. Open the grille
panel and reach into the opening at the back to grasp
the power cord. Pull the power cord into the opening
as you push the refrigerator back.
, Gently push refrigerator into the opening with hands
against front corners.
IMPORTANT NOTE:When the refrigerator is installed under a soffit
or if there is not enough height for this method of security, brackets
cannot beused.Proceedtostep 7 to levelthe refrigeratorand then to
step 9 to secure refrigerator to cabinets. See step 8 if you have metal
wallstuds.Therefrigerator mustbe securedto preventtipping.

Installation Instructions
ISTEP71LEVEL REFRIGERATOR
All models have 4-point leveling. The front is
supported by leveling legs, the rear is supported
by adjustable wheels. Both are accessible from
the front of the refrigerator.
, To level the back of the refrigerator, turn the 7/16"
hex nut located above the front wheels. Turn
clockwise to raise or counterclockwise to lower the
refrigerator.
, Forfront leveling, use a 1-1/4" open-end wrench.
Adjust height of refrigerator to match installation
cutout opening 85-1/2" to 84-1/2". The refrigerator
should be level and plumb with cabinetry.
Hex Nut Ad
Rear Wheels
CAUTION:
The rear leveling wheels and front leveling legs
are limited to a maximum height adjustment of 1".
If the installation requires more than 84-1/2" height,
the installer should elevate the refrigerator on a sheet
of plywood or runners. Cabinetry trim could also
be added across the top of the opening to shorten
the opening. If you attempt to raise the refrigerator
more than 1", you will damage the front leveling
legs and the rear leveling wheels. Make adjustments
in small increments.
PRUDENCE
Les roues de nivellement arri6re et les pattes de
nivellement avant permettent un r6glage maximal
de 25 mm (1 po).Si I'ouverture pour le r6frig6rateur
a une hauteur sup6rieure 6 2,15 m (8/4-!/2 po),
I'installateur dolt 61everle r6frig6rateur sur une feuille
de contre-plaqu6 ou des glissi6res. IIest 6galement
possible d'ajouter des baguettes de finition des
placards sur le haut de I'ouverture afin de la r6duire.
Lever le refrig6rateur de plus de 25 mm (1 po)
endommage les pattes de nivellement avant
et les roues de nivellement arriere.
ISTEP 8 ALTERNATE ANTI-TIP
PROCEDURE
The refrigerator must be secured to prevent tipping.
The anti-tip brackets cannot be used on metal
wall studs. Use this Alternate Procedure to secure
the refrigerator against tip-over whenever metal
wall studs are encountered and there is no soffit.
i'_SIde View /
Top Case Trim _T_OpCaseTjri_
/ /--\ -
__ "_.\ \ / /
_-I/2" DrywallScrews
Through Trimand Into Soffit
or 3/4" Min.Wood grace
, Raisethe grille panel to access case trim.
, Use a 3/16" bit to drill four evenly spaced clearance
holes through the metal top case trim.
Use a 1/16" bit to drill to pilot holes through the metal
clearance holes and into the wood soffit. The holes
should be centered in the soffit or a 3/4" min. wood
brace. The brace spanning the enclosure must
be securely fastened to cabinets on both sides.
Install four, 1-1/2" drywall screws into the pilot holes.
13

Installation Instructions
[STEP9] SECUREREFRIGERATOR
TO CABINETRY
Whenever possible, perform this step for anti-tip
security, or when anti-tip brackets cannot be used.
The refrigerator must be secured to prevent tipping.
. Raisethe grille panel to access the case trim.
. Drill a hole in the trim and drive a screw through
the trim into the adjacent cabinet,
. Follow the same procedure on the opposite side.
Through Case Trim Into
Adjacent Cabinets
[STEP101ADJUST DOOR SWING
NOTE: This refrigerator has a 2-position door stop.
When space does not allow the door to swing open
fully to 130 °,you may change the door swing to a 90 °
opening, Skip this step if door opening is satisfactory
for your installation situation.
Interior
130°
Door
/
/'
Hinge
. Open the door to view the bottom hinge.
Note the door stop pin locations. The pin is factory
installed in the 130° position,
. Close the door. From below, use pliers to unscrew
the door stop and reinstall into the 90° position,
ISTEP 111 INSTALL GRILLE PANEL
(for Custom Panel Models only)
To insert the framed or overlay panel into the grille:
. Raisethe grille panel to the stop position.
A=== j
Loosen Loosen
Side Side
Trim Trim
Screw Screw
AdjustNutBelow
SpringtoAccommodate
PanelWeight
Loosen the screws on the side trim behind the frame.
Remove the bottom trim.
CAUTION: The metal panel may be
slippery, Grip the metal panel firmly so the panel does
not slip out of the frame and cause personal injury or
damage to the frame,
PRUDENCE : LepanneauenmGtal
peut b#tre glissant. Tenir fermement le panneau en
mGtal,de mani#re 6 ce que le pannemu ne glisse pros
en dehors du cadre en provoquant des blessures
corporelles ou des dommages au cadre,
. Slide the panel over the metal backer panel and into
the trim,
. If necessary, top with a wood block until the panel
slips under the top trim piece,
. Reassemble the bottom trim. Tighten the screws.
. Adjust the hinge spring to accommodate the panel
weight, if necessary,
14

Installation Instructions
[STEP121INSTALL 1/4" FRAMED PANELS Goto Step12AforOverlayPanels
g0
!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_i!_
!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]i!
!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]i!
!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]i!
_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_lil_l_l
I
Install door panels:
. Open the door to 90°. Remove the 6 Phillips head screws
from the door handle,
. Remove the handle. Retain all screws.
. Remove the 6 screws holding the trim, then lift off
the trim. Retain the screws.
. Slide the framed panel into the door trim.
Dispenser Models Only:
. The dispenser controls protrude beyond the face
of the freezer door. To avoid damage to the dispenser,
the trim at the top of the door should be removed,
. Remove the screws holding the top trim in place.
. Place the freezer panel into the bottom channel
and slide into the hinge side trim,
. Reinstall the top trim piece with screws.
. There are two sets of holes in the handle side trim.
Replace the handle side trim by installing the original
screws in the FRONTscrew holes.
. Secure the handle to the door using the REARscrew
holes,
. Follow the same procedures to install the opposite panel.
. Check to be sure the handles are evenly aligned with
each other at the top. To adjust, loosen the handle
screws and slide up or down. Tighten the screws.
NOTE:Aluminum cover trim is supplied for use with
custom handles on overlay panels, It is not intended for
use with 1/4" panels. Discard the cover trim when using
1/4" framed panels.
Handle
Trim
Suppfied
H_Jndle Shown
in 7/4" P_ne/
Position
Door Trim
Refrigerator
Door
I_\\\\ \\\\\\\\\\\\\\\\\'1
\
'\\\ // Use Front Hole to Secure Trim
Use Rear Holes
to Secure Handle
15

Installation Instructions
ISTEP12A IINSTALL OVERLAYPANELS
Install door panels:
. Open door to 90°. Remove the 6 Phillips head screws
from the door handle,
. Remove the handle. Retain all screws.
. Remove the 6 screws holding the trim, then lift off
the trim. Retain the screws.
. Slide the overlay panel into the door trim.
Dispenser Models Only:
. The dispenser controls protrude beyond the face
of the freezer door. To avoid damage to the dispenser,
the trim at the top of the door should be removed,
. Remove the screws holding the top trim in place.
. Place the assembled freezer panel into the bottom
channel and slide into the hinge side trim,
. Reinstall the top trim piece with the screws.
. There are two sets of holes in the handle side trim.
Replace handle side trim by installing the original screws
in the REARscrew holes,
. Secure the handle to the door using the FRONT
screw holes,
. Follow the same procedures to install the opposite panel.
. Check to be sure the handles are evenly aligned with
each other at the top. To adjust, loosen the handle
screws and slide up or down. Tighten the screws.
Handle
Trim
Move
Forward
For 3/4"
Panel
1
Door Trim
Refrigerator
Door
k\\\\\\\\\\\\\\\\\\\\\l
Supplied Handle
Shown in Overlay
Pane/Position
//
/
", _;/_Use Front Hole:
'_. _ to Secure Handl,
- -.......... use uear HOleS
to Secure Trim
16

Installation Instructions
ISTEP12AI(continued)
Custom Handles
, If you are using custom handles, the handle must
be properly secured to the overlay panel before sliding
the panel into the trim.
, The cabinet manufacturer will supply the custom
handle and hardware.
, Discard the supplied handle.
Re/nst_J#a# original screws,
, Reinstall the handle side trim, using all 12 supplied
flat-head screws, plus the 12 flat-head screws
originally installed in the handle trim,
, Install e supplied end cap onto the top of the door,
using a Phillips head screwdriver and the 2 screws
provided, Hand-tighten the screws into the end caps.
Do not overtighten; damage will occur.
, Clean the aluminum trim with rubbing alcohol-
do not use alcohols with oil or lanolin that will prevent
adhesion of double-sided tape.
, Slip the aluminum cover trim behind the top end cap
to check the fit. The aluminum cover trim has a recess
on each end which fits the end cap.
Cover Trim
Insert Aluminum
Trim/nto End
Cap. ff
Top End Cap
f-it,s-Over the
Aluminum Trim,
Secure Cap with
2Screw.s,
, Remove the trim. Peel away a few inches
of the adhesive backing.
IMPORTANT: The tape is very sticky and strong. Once
it adheres to a surface, it cannot be removed without
damaging both surfaces. Do not install the trim before
the final wood panels are in place, Be sure to align
the trim carefully before removing the paper backing.
ISTEP12A1(continued)
, Carefully place the aluminum cover trim into top
end cap so that the recess is aligned with the cap.
Use the top to bottom grooves along the handle side
to align the cover trim accurately. Pull the tape a few
inches at a time while pressing the trim against
the door. Press and hold approximately 10 seconds
before continuing along the length of the door.
, Install another end cap at the bottom of the door
to secure the cover trim. Use a stubby Phillips head
screwdriver and the 2 screws provided.
NOTE: Make sure there are no gaps in the installation.
, Follow the same procedure on the opposite door.
17

Installation Instructions
STEP 131 INSTALL DISPENSER TRIM
Skip this step is you are installing a stainless steel
wrapped or a non-dispenser refrigerator.
There are two dispenser trims shipped with your
refrigerator. Select the appropriate trim for your
application.
J
Framed
Panel
Trim
J
Overlag
Panel
Trim
Compare the dispenser trims. Note that
the inside depth of the frames are different.
Choose the trim with less depth for framed
panels, choose the deeper one for overlay
panels.
Dispenser trim fit over the custom panel depends on
correct panel thickness. See pages 7and 8 for panel
construction information.
. Pressand snap the dispenser trim into the dispenser
recess on the refrigerator door,
If an excessive gap exists around the dispenser trim
or if the panel fits loosely in the door frame, foam tape
may be applied to help improve the fit. Remove
the trim and panel and apply the foam tape
to the door around the dispenser and in the corners.
[STEP14 CONNECTWATER SUPPLY
L
.......,, Refrigerator House /'
_Water Supplg Water Supp!.gf
"_"--- _ ......................... -o°J"
. Locate and bring the tubing to the front
of the cabinet.
, Turn the water on to flush debris from the line.
Run about a quart of water through the tubing
into a bucket, then shut off the water.
Copper Tubing:
, Slip a 1/4" nut and ferrule (provided) over both ends of
the copper tubing. Insert the tube into the union fitting
on the unit and tighten the nut to the union.
, Turn on the water to check for leaks.
GESmartConnect _ Tubing:
, Insert the molded end of the tubing
into the refrigerator connection. Tighten
the compression nut until it isjust hand tight.
, Tighten one additional turn with a wrench.
Overtightening can cause leaks!
, Turn on the water to check for leaks.
NOTE: Make sure excess tubing length does not
interfere with the toekick installation.
18

Installation Instructions
ISTEP151CONNECT POWER, CLOSE
GRILLE PANEL
. Open the grill panel.
. Plug in the power cord (if necessary) by reaching
into the opening next to the water filter, If access is
too tight, remove the 2 screws holding the water filter
bracket and move aside, Plug in the power cord and
secure the bracket with the original screws,
\
Maste'iLight
Switches Electrical OutletAccess
. Check to make sure power to refrigerator is on
by opening refrigerator door to see if interior lights
are on,
. The temperature controls are preset at 37°F for
the fresh food section and 0°F for the freezer.
. Allow 24 hours to stabilize before making
adjustments,
ISTEP 161 START ICEMAKER
Power
Switch Fee/er Arm
/cernc_ker
/
. Slide the switch to ON. The icemaker will begin
operation automatically,
. Be sure nothing interferes with the sweep
of the feeler arm,
. Discard the first full bucket of ice cubes.
. To turn the icemaker off, slide the switch to OFF.
ISTEP171INSTALL TOEKICKS
. Locate the supplied toekicks (shipped taped to
the side of the refrigerator).
. First, attach the LARGERtoekick to the refigerator
using ONLYthe top center hole (1).
. Next, attach the toekick extension to the refrigerator
using the three lower slots (2).
ij_% o../1/ 1-- t
. A custom toekick can be installed to match or
complement the surrounding cabinetry. Usethe
supplied toekick as a template to cut the shape,
INSPECTFINAL INSTALLATION
Check door alignment
Stand back away from the refrigerator to inspect
the final installation,
. Check to be sure the handles are evenly aligned with
each other at the top. To adjust, loosen the handle
screws and slide up or down. Tighten the screws.
. Shipping or the addition of heavy door panels
may have caused the doors to move slightly out
of alignment,
IIh--_:_-€l
Door Out of
Alignment
z
/
_\\\\\\\
Bushing
/
/
5/16"Wrencl\\..Raise
. If necessary, the fresh food door may be adjusted up
or down to align with the freezer door.
. Use a 5/16" wrench to adjust the hinge pin as shown.
19

ZKHSS2 Tubular Stainless Steel Handles
This kit provides for the installation of Tubular Stainless Steel
handles on 3/4" overlay custom panels.
TOOLS AND MATERIALS REQUIRED
In addition to the custom door panels, you need:
• #2 Phillipsscrewdriver • Centerpunch
•Drill and 7/32 "bit
c_nd7/8" .s-pc_debit
• Safetyglasses
Hammer
•Pencil
PARTS LIST
s
8 N_ndle ste_ndofFs
70 Screws for hc_ndle
32x 7"pcln hee_d rnc_chine
screws (B required, 2 extn_)
3/32" Allen wrench for set screws
70 PIc_stic .spc_cersste_ndoffls /170-
(8 required, 2extra)
70 Set screw.s (8 required, 2 extrc_)
[STEP 1[ REMOVE DOOR HANDLES
, Open the refrigerator door to 90°. Remove
the 6 screws holding the handle to the door.
Remove the 6 screws holding the handle side trim.
Retain all screws and trim. Discard the handle.
, Follow the same procedure to remove the freezer
handle and trim,
2O