GE RHM 15 Operating instructions

wvvw.GEAppliances.com
Safety Instructions
Adapter Plugs ................ 6
Connecting Electricity ......... 4
Extension Cords .............. 5
Proper Disposal .............. 2
Safety Precautions ............ 3
Operating Instructions
Automatic Icemaker .......... 11
Care and Cleaning ........ 12, 15
Shelves .................... 8, 9
Storage Drawers ............ 9, 10
Temperature Controls .......... 7
Installation Instructions
Preparing to Install
the Reli'igerator ............. 14
Reversing the Door Swing .. 19-24
Water Line Installation ..... 15-19
Troubleshooting Tips
Before You Call For Service . .26, 27
Normal Operating Sounds ..... 25
Customer Service
Consumer Support .... Back Cover
Product Registration ....... 29, 30
Warranty for
Canadian Custome_ ......... 28
Warranty fbr U.S. Customers ... 31
Models
15, 16, 17, 18
Write the model and serial
numbers here:
Model #
Serial #
You can find them on a label on
the upper left side of the fi'esh food
compartment.
162D3905P010 49-60213 07-02JR

ADANGER!RISKOFCHILDENTRAPMENT
PROPERDISPOSALOFTHEREFRIGERATOR
Child enn'apment and suffocation are not
problems of the past. Junked or abandoned
refrigerators are still dangerous...even if they
will sit for '_ust a few days." lfyou are getting
rid of your old refiigerato_; please follow the
instructions below to help prevent accidents.
Before You Throw Away Your Old
Refrigerator or Freezer:
@ Take off the doors.
gNLeave the shelves in place so that children
may not easily climb inside.
Refrigerants
All refrigeration products contain refi'igerants,
which under federal law must be removed prior
to product disposal. If you are getting rid of an
old refl'igeration product, check with the
company handling the disposal about what
to do.
ADANGER!RISQUESPOURLESENFANTS
COMMENTVOUSDEBARRASSER
CONVENABLEMENTDEVOTREANCIENRE-FRIGE-RATEUR
Les enfants pris au pi&ge ou morts d'asphyxie
sont tot_ours d'acmalit_. Les rdfrig&'ateurs
abandonn& sont toujours aussi dangereux,
m&me si on n'attend que _<quelques.jours,,
pour s'en d_barrassm: Si vous ne gardez pas
votre ancien rdfrig_ratem; veuillez suiwe les
directives ci<tessous afin de pr&,enir les accidents.
Avant de volesd_barrasserde votreancien
r_frig_rateuroucong#lateur :
@ D_montez les portes.
@ Laissez les clayettes en place afin d'emp&her
les enfants de grimper _t l'int&ieun
R#frig#rants
Tousles appareils de r_fl'ig_ration contiennent
des rdfrigg_rants qui, confbrmg_ment aux lois
fdddrales, doivent _tre enlev& avant route
dlimination de l'appareil. Si vous vous
ddbarrassez de vieux appareils de rdfrigg_ration,
v&ifiez, aupr_s de la soci_td qui s'occupe de
leur dlimination, ce que vous devez faire.
2

IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING. www.GEAppliances.com
WARNING!
Use this appliance only for its intended purpose as described in this Owner's Manual.
SAFETYPRECAUflONS
When using electrical appliances, basic safety precautions should be followed, including the following:
@This refrigerator must be properly installed
and located in accordance with tile Installation
Instructions before it is used.
gNDonot allow children to climb, stand or hang
on the shelves in tile refrigerator. They could
damage the refrigerator and seriously injure
themselves.
@Do not touch tile cold surfaces in tile freezer
compartment when hands are damp or wet.
Skin may stick to these extremely cold surfaces.
@Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
@Keep fingers out of tile "pinch point" areas;
clearances between the doors and between
the doors and cabinet are necessarily small.
Be careful closing doors when children are
in the area.
@In refrigerators with automatic icemakers,
avoid contact Mth the moving parts of the
ejector mechanism, or wi@ the heating element
that releases the cubes. Do not place fingers or
hands on the automatic icemaking mechanism
while the refrigerator is plugged in.
@Unplug the refi'igerator before cleaning and
making repairs.
NOTE:Westronglyrecommendthatanyservicingbe
performedbyaquafifiedindividual.
@Turning the control to the 0pos@on does
not remove power to the light circuit.
@Do not refreeze frozen foods which have
thawed completely.
f f
MESURESDESECURITEIMPORTANTES.
LISEZD'ABORDTOUTESLESDIRECTIVES.
AVERTISSEMENT!
N'utilisez cot _lectrom#nage r que pour !'usage auque! il est destinfi, comme expliqu6 dans !e
pr#sent manuel
MESURESDESECURIT¢L
Lorsque vous utilisez un appareil Olectrique, observez @ujours les mesures de sOcurit# de base,
y compris les suivan@s.
gNInstallez le r4frig4rateur conform4ment aux
directives d'installation a-cant de l'ufiliser.
gNNe laissez pas les enfants grimpm; s'asseoiJ;
se tenir debout ni se pendre aux clayettes du
rdfrig_rateur, lls pourraient endommager le
rdfrig_rateur et se blesser gravement.
gNN'entreposez et n'udlisez pas @essence ou
autres vapeurs et liquides inflammables it
proximi@ de cet appareil ou de tout autre
appareil 41ectrom4nageE
g_l_loignez les doigts des parties du rdfrig_rateur
o6 l'on peut t:acilement se pincer : les espaces
entre les portes et entre les portes et les placards
sont toujours 4troits. Soyez prudent lorsque
vous @rmez les portes de l'appareil en pr@ence
des enfants.
gNSi votre @frigdrateur est do@ d'une machine 'a
glaqons automatique dvitez le contact avec les
pi&ces mobiles du m&anisme _jectem; ou avec
l'_l_ment chaui_ant qui lib_re les glaqons.
Ne posez pas les doigts ou les mains sur le
m&anisme de la machine it glagons pendant
que le r@i'ig&ateur est branch4.
@Ne touchez pas les surfaces froides du cong41ateur
si vous avez les mains humides ou mouill4es :la
peau risque d'adh4rer 'aces surfaces tr@ froides.
N D4branchez votre r4frig4rateur avant de le
nettoyer ou de le rdparer.
REMARQUE: Nousvousrecommandonsvivementde
co@iertouter#paration_untechnicienqualifi#.
@Lorsque vous r4glez la commande sur 0(@eint),
l'alimentafion 41ectrique de l'ampoule n'est pas
coup4e.
@ Ne recongelez pas les aliments surgel& qui ont
compl@ement ddgel4. 3

IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING.
AWARNING'!
HOWTOCONNECTELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet
m minimize the possibility of"elecnic shock hazard
from this appliance.
Have the w-alloudet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
Where a standard 2-prong w_dloutlet is
encountered, it is your personal responsibility and
obligation m have it replaced with a properly
grounded 3-prong wall oudet.
The refrigerator should always be plugged into its
own individual electrical outlet which has a voltage
rating that matches tile rating plate.
This provides the hest performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
Never unplug your refrigerator by pulling on the
power cord. Alwaysgrip plug firmly and pull
straight out from the outlet.
Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.
When moving the refrigerator av_-ayfrom the
w_dl,be carefltl not to roll over or damage the
power cord.
f f
MESURESDESECURITEIMPORTANTES.
LISEZD'ABORDTOUTESLESDIRECTIVES.
4
AAVERTISSEMENTI
RACCORDEMENTELECTRIOUE
Ne coupez ni retirez en aucun cas la troisifime broche (mise _la terre) de la fiche du cordon
d'alimentation. Pour votre sOcurit6, cet appareil doit Otre correctement mis _la terre.
Le cordon d'alimentation de cet appareil est
muni d'une fiche 'a3 broches (mise 'a la terre)
qui se branche clans une prise murale ordinaire
'a3 alv_oles (mise 5_la terre) pour r_duire au
minimum les risques de chocs _lectriques.
Faites examiner la prise de courant et le circuit
par tin dlecnicien qualiil_ pour vous assurer que
la prise est correctement mise 'ala terre.
Si la prise murale est du type standard _ 2 alvdoles,
il vous incombe de la taire remplacer par une
prise 5_3 alvdoles correctement mise 5_la terre.
Le rdfrig_rateur doit toujours _tre brancbe dans
sa propre prise de courant, dont la tension
nominale est identique 'acelle indiqu_e sur la
plaque signal_tique.
Cette precaution est recommandde pour g_randr
tin rendement optimum et _viter une surcharge des
circuits dlecniques de la rdsidence, ce qui pourrait
crder un risque d'incendie par surchauf{i? des ills.
Ne d_branchez,jamais le rdfiig_rateur en tirant
stir le cordon d'alimentation. Saisissez fermement
la fiche du cordon et tirez droit pour la retirer
de la prise.
Rg_parezou remplacez immg_diatement tout cordon
eitilochd ou endommag_. N t tilisez past n cordon
fizndill_ ou pr&enrant des signes d'usure.
Lorsque vous dg_placezvotre r_frig_rateur du mm;
daites attention de ne pas le fhire rouler sur le cordon
d"Aimentation afin de ne pas l'endommage_:

IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING. ,_GEAt,t,,a.cosco.,
USEOFEXTENSIONCORDS
Because of potential safety hazards under certain conditions, we strongly recommend
againstthe use of an extension cord.
Howevm; ifyou must use an extension cord, it is absolutely necessary that it be a UL-listed (in tile United
States) or a CNA certified (in Canada), B-wire grounding type appliance extension cord having a grounding
type plug and outlet and that the elecnical rating of the cord be 15 amperes (minimum) and 120 volts.
CORDONSPROLONGATEURS
Nous vous recommandons fortement de ne pas utiliser de cordons prolongateurs _cause des risques
potentiels qu'ils pr6sentent dans certaines conditions.
Toutefois sivous d_cidez d'utiliser tout de m{:me un cordon prolongatem; il est absolument n_cesmire
clu'il s'agisse d'un cordon 'a3 ills avec mise 5.la terre pour appareils dlectromdnagers homologud UL (aux
Etats-Unis) ou certifi_ CSA (au Canada), pourvu d'une fiche et d'une prise mises _tla terre de 15 amp&res
(minimum) et de 120 volts.
5

IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING.
USEOFADAPTERPLUGS(Adapter plugs not permitted in Canada)
Because of potential safety hazards under certain conditions, we strongly recommend against
the use of an adapter plug.
Howevm; ifyou must use an adapter, where local
codes permit, a temporaryconnectionmay be made
to a properly grounded 2-prong wall outlet by use
ofa UL-listed adapter available at most local
hardware stores.
The larger slot in tile adapter must be aligned with
the larger slot in the wall oudet to proxdde proper
polarity in the connection of the power cord.
When disconnecting tile power cord from tile
adapter, always hold tile adapter in place with one
hand while pulling tile power cord plug with the
other hand. If this is not done, tile adapter ground
terminal is very likely to break with repeated use.
If the adapter ground terminal breaks, DO NOTUSE
the refrigerator until a proper ground has been
established.
Attachingtheadaptergroundterminaltoa walloutletcover
screwdoesnotgroundtheapplianceunlessthecoverscrew
ismetal,andnotinsulated,andthewaftoutletisgrounded
throughthehousewiring.Youshouldhavethecircuitchecked
bya qualifiedelectriciantomakesuretheoutletisproperly
grounded.
READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.
SAVETHESEINSTRUCTIONS
f f
MESURESDESECURITEIMPORTANTES.
LISEZD'ABORDTOUTESLESDIRECTIVES.
6
FICHED'ADAPTATION(Fichesd'_daptatiannonperm&esau Canada)
Nous vous recommandons fortement de no pas utiliser une fiche d'adaptation _cause des risques
potentiels qu'elle pr6sente clans certaines circonstances.
Toutefois, si vous d&idez d'utiliser tout de m&me
une fiche d'adaptation, vous pouvez effecmer un
raccordement ternpotaire, si les codes locaux le
permettent, dans une prise de courant 'a2 alv4oles
ad4quatement mise _tla terre en utilisant une fiche
d'adaptation homologu4e UL, en vente dans la
plupart des quincailleries.
La fente la plus longue de la fiche deft &trealign_e
avec la fente la plus longue de la prise murale afin
d'assurer la polarit_ appropri_e pour le
branchement du cordon d'alimentation.
Si la borne de mise 'a la terre de la fiche casse,
N'UTILISEZPASI'appareil tant qu'une mise _t la terre
addquate n'aura pas _td rdtablie.
Lefaitde fixerla bornederaise_la terredelafiche
d`adaptation#laplaquedelaprisedecourantn'assurepas
automatiquementlaraise# la terredel'appareil,flfautquela
vissoftenm#tal,nonisolCe,etquelaprisedecourantsoft
raise_ laterreparfentremiseduc#blagedelarfisidence.
Faitesv#rifierlecircuitparun#lectricienqualifi#pourvous
assurercluelapriseestad#quatementraise_ laterre.
Lorsque vous ddbranchez le cordon d'alimentation
de la fiche d'adaptation, saisissez tot_ours la fiche
d'une main pendant que vous tirez sur la fiche
du cordon d'alimentation de l'autre. Sinon,
la borne de mise _t la terre de la fiche d'adaptation
risque de casser avec le temps.
/ /
VEUILLEZLIREETSUIVREATTENTIVEMENTCESMESURESDESECURITE.
CONSERVEZCESDIRECTIVES

Aboutthetemperaturecontroldial ww_.GEAppliances.com
Turning the dial to 0stops cooling in both compartments-fresh food and freezer. It does not shut off power to the
refrigerator.
ControlSettings
Temperature ControlDial
The temperature control dial has nine settings plus 0. 1 is the warmest. 9is the coldest.
At first, set the dial at 5.
After using the refi'igeratol, adjust the dial if necessal T.
Insert a coin into the slot in the middle of the dial and you can turn the dial to the setting
that's best suited to your needs.
Allow 24 hours for the refi'igerator to get cold.

Aboutthefreshfoodcompartmentshelves.
Shelf supports at various levels allow you to custom-space your shelves. Not all features are on all models.
Half-Width Shelves
One end of the shelf rests on a molded
side-wall support; a bracket on the other
end hooks into a track on the rear
cabinet wall.
TOremove, liR the shelf up at front, then
off the support and out of the track.
NOTE:Theshelf to therightof the trackis
oeslgnedtohookintothe@t-hand slot,
rneshelf tothe left is designedtohook
intotheleft-handslot.
TOreplace, select desired shelf height.
With shelf front raised slightly, hook the
bracket's top lug into the track, then
lower the shelf onto the support.
Full-Width Shelves
Some models have a steel wire sliding
shelf, a stationa_ T tempered glass shelf or
two steel wire stationary shelves. These
shelves can be moved to another place
in the fi'esh food compartment.
The full-width sliding shelf has stop-locks.
When placed correctly on the shelf
supports, the shelf will stop before coming
completely out of the refrigerator and will
not tilt when you place food on it or
remove food from it.
Toremovethe full-width shelves, lift the
rear of the shelf and pull forward.
Toremove a full-width shelf when the fresh
food compartment door cannot be opened
fully, lift the rear of" the shelf, pull
forward and down, tilt the shelf and
take it out.
8

About the freezer compartment shelves, ww .GEAppliances.com
Some models have an ice-tray shelf and some have a full-width step shelf.
Ice-Tray Sheff
!_i_i(i_!ii(i_i_)_i!_!_i_i_i_!_!_!_i_!_!i_i_!_!_!;_i_i_i_!__i_i_ii_i_I_i_iiii!_i_)_)i__ _i_!_i_i_ii_ii_i_i_i_i_i_i_i_!i_!i?)i!i!_i_
TOremovetheice-tray shelf,lift the ]eft
side of the shelf off its supports, then
pull the shelf to the left to free it of the
.................. plug supports. Pull the shelf to tile right
to fl'ee the pins from the holes in the
cabinet wall.
Step Shelf
TOremovethestepshelf:
[]Lift left side of shelf slightly.
[]Move shelf to tile left to free its right
ends from holes in the cabinet wall.
[]Lower right side of shelf; move shelf to
tile right and take it out.
TOreplace thestepshelf:
[With shelf tilted as shown, fit left ends
of shelf into holes in cabinet wall.
Lift left side of shelf slightly, swing shelf
up, fit right ends of shelf into holes in
cabinet wall, and lower shelf into place.
About the storage drawers.
Not all features are on all models.
Fruit and Vegetable Drawers
Excess water that may accumulate in the
bottom of the drawers should be emptied
and the drawers wiped dry.
Snacks Drawer
The snacks drawer can be moved to the
nlost usef_fl location for your fhmily's
needs.
9

About storage drawer and cover removal.
Not all features are on all models.
Drawer and Cover Removal
Drawers can be removed easily by grasping
tile sides and lifting up slightly while
pulling drawers past tile stop location.
Full-Width Drawer with Plastic Cover
Toremovethecover,lift it of?["its supports,
pull it forward, tilt it and take it out.
Twin Drawers with Glass Cover
Toremove:
[]Remove the drawers.
[]Reach in, push the front of glass
cover up, and at the same time,
pull it forward as far as it will come.
Tilt it and take it out. Avoid cleaning the
cold glass cover with hot w-ater because
the extreme temperature difference may
cause it to break.
[]Remove the drawer frame. (Always
remove the glass cover before you
take out the drawer frame.)
Lift the frame off the supports at each
side and back, pull it forw-ard, tilt it and
take it out.
Toreplace:
[]Lower the frame until it rests on the
supports at each side and back.
[]Replace the glass corm; pushing its
rear edge firmly into the rear frame
channel and gently lowering tile front
into place.
[]Replace the drawers.
10

About the automatic icemaker, www.GEAppliances.com
A newly-installed refrigerator may take 12to 24 hours to begin making ice.
Automatic Icemaker (onsomemodels)
Powerswitch model
Feelerarmmodel
The icemaker will produce seven cubes
per cycle-approximately 100-130 cubes
in a 24-hour period, depending on
freezer comparrment temperature,
room temperature, number of door
openings and other use conditions.
There are two vypes of icemakers: power
switch models and feeler arm models.
If the refrigerator is operated before
the w-ater connection is made to tile
icemakm; set the power switch to 0(0if)
or move tile feeler arm to the STOP(up)
position.
When the refrigerator has been
connected to the water supply, set tile
power svdtch to tile/(on)position or move
the feeler arm m the ON (down) position.
On power switch models, tile green light
will come on.
You will hear a buzzing sound each time
the icemaker fills with water.
The icemaker will fill with water when
it cools to 15°E A neMy-installed
refrigerator may take 12 to 24 hours
to begin making ice cubes.
Throw away the first few batches of ice
to allow the w-ater line to clear.
Be sure nothing interferes with the
sweep of the feeler arm.
When the bin fills to the level of the
fizeler arm, the icemaker will stop
producing ice.
It is normal for several cubes to be joined
together.
If ice is not used frequently, old ice cubes
will become cloudy, taste stale and shrink.
On power switch models, the green power
light will blink if ice cubes get stuck in the
icemaker. To correct this, set the power
switch to O(off)and remove the cubes. Set
the power switch to I(on) to restm't the
icemakm: After the icemaker has been
turned on again, there will be a delay of
about 45 minutes before the icemaker
resumes operation.
NOTE:Inhomeswith lower-than-averagewater
pressure,youmayheartheicemakercycle
multiple timeswhenmakingonehatchof ice.
Icemaker Accessory Kit
If your refrigerator did not already come
equipped with an automatic icemaker,
an icemaker accessory kit is available at
extra cost.
Check the back of the refrigerator for
the specific icemaker kit needed for your
model.
11

Care and cleaning of the refrigerator.
Cleaningthe condenser coils.
Cleaning the Outside
The door handles and trim (on some
models). Clean witb a cloth dampened
with soapy w_ateE Dry with a soft cloth.
Keep the outside clean. Wipe with a clean
cloth lightly dampened with kitchen
appliance w_ax or mild liquid dish
detergent. Dry and polish with a clean,
soft cloth.
Donot wipetherefrigeratorwith a soileddish
clothor wet towel. Thesemayleavea residue
thatcanerodethepaint. Donotusescouring
pads,powderedcleaners,bleachor cleaners
containingbleachbecausetheseproductscan
scratchandweakenthepaint finish.
Cleaning the Inside
TOhelp prevent odors, leave an open box
of baking soda in the fresh food and
fl'eezer compartments.
Unplugthe refrigeratorbeforecleaning.
If"tiffs is not practical, wring excess
moisture out of sponge or cloth when
cleaning around swiwhes, lights or
controls.
Use w_arm ,actter and baking soda solution-
about a tablespoon (15 ml) of baking soda
to a quart (1 liter) ofw_ateE This both
cleans and neutralizes odors. Rinse and
wipe d W.
After cleaning the door gaskets, apply a
thin layer of petroleum jelly to the door
gaskets at the hinge side. This helps keep
the gaskets from sticking and bending
out of shape.
Avoidcleaningcoldglass shelves (onsome
models)with hotwaterbecausetheextreme
temperaturedifferencemaycausethemto
break.HandleglassshelvescarefuflgBumping
temperedglasscancauseit toshatte_
Eviterdenettoyerlestablettesen verrefroides
(surcertainsmodbles)_ I'eauchaudeparceque
l'#cartdetempfiratureextr#merisquede les
craque_Manipulerlestablettesen verreavec
pr#caution.Le verretremp#soumis_unchoc
risquede sefracasser
Donot washanyplasticrefrigeratorparts in
thedishwashe_
Condenser
There is no need for routine condenser
cleaning in normal home operating
environments. Howevm; in environments
that may be particularly dusty or greasy,
the condenser should be cleaned
periodically fbr efticient refrigerator
operation.
To clean the condensm, turn tbe
temperature control dial to O.Sweep
a_a_ayor vacuum up dust.
For best results, use a brush specially
designed for tl_is purpose. It is available
at most appliance parts stores.
12

ww_.GEAppliances.com
Behind the Refrigerator
Be careflll when moving the refrigerator
a_a_ayfrom the wall. All types of floor
coverings can be damaged, particularly
cushioned coverings and those with
embossed surfhces.
Turn the leveling legs at each front corner
of the refrigerator counterclockwdse until
the rollers support the refrigeraton Pull the
refrigerator straight out and return it to
position by pushing it straight in. Moving
the refrigerator in a side direction may
result in damage to the floor covering or
refrigerator.
Whenpushingtherefrigeratorback,makesure
youdon'troll overthepowercordoricemaker
supplyline (onsomemodels).
Enpoussantle rfifrig#rateurenplace,veiller#ne
pasle fairaraulersurle cordond'alimentationou
lacanalisationd'eaude la machine,)glawns
(surcertainsmodOles).
After rolling the refrigerator back into
place, turn the legs clockwise until the
legs again bear the weight of the
refrigeraton
Light Bulb Replacement
To replace a burned-out bulb, unplug
the refrigerator from its electrical outlet,
unscrew the bulb when cool and replace
it with an appliance bulb of the same or
lower wattage.
Turningthecontrolto theOpositiondoesnot
removepowerto thelightcircuit.
Preparing for Vacation
For long vacations or absences, remove
food and unplug the refYigeratol: Move
the temperature control dial to the 0
position, and clean the interior with a
baking soda solution of one tablespoon
(15 ml) of baking soda to one quart
(1 liter) ofwatm: Leave the doors open.
Set the icemaker power s,Mtch to the
0(off) position or move the feeler arm to
the STOP (up) position (depending on
model) and shut off the water supply to
the refrigerator:
If the temperature can drop below
freezing, have a qualified servicer drain
the water supply system (on some
models) to prevent serious property
damage due to flooding.
Preparing to Move
Secure all loose items such as grille,
shelves and drawers by taping them
securely in place to prevent damage.
Besuretherefrigeratorstaysin an upright
positionduringmoving.
13

Inst aIlati on Refrigerater
'ns-r -" nsz zuczzo Models 15,16,17,18
Questions?Call SOO.GE.CARES(800.432.2737)OrvisiiOurwebsiteat:www.GEAppliances.com [
Canada,call L800.361.3400orVi_itourWebsitea: www.geappliances.ca [
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•IMPORTANT - Savedlese
instructions for local inspector's use.
• IMPORTANT - Obso_,,oall
governing codes and ordinances.
• Note to Installer - Besure to leave these
instructions with the Consumes:
• Note to Consumer - Keepthese instructions
for future reference.
•Skill level - Installation of this appliance requires
basic mechanical skills.
•Completion time - Refrigerator Installation
15 minutes
Reversing the Door Swing
1 hour
• Proper installation is tim responsibility of the
installer.
• Product failure due to improper installation is not
covered under the Warranty.
WATER SUPPLY TO THE ICEMAKER
800.626.2002 (in Canada 1.888.261.3055).
REFRIGERATOR LOCATION
•Do not install tile refrigerator where the temperature
will go below 60°F (16°C) because it will not run often
enoug h to maintain proper temperatures.
• Install it on a floor strong enough to support it fully
loaded.
CLEARANCES
Mlow the following clearances for ease of installation,
proper air circulation and plumbing and electrical
connections.
• Sides 3/4" (19 mm)
• Top 1" (25 mm)
• Back 1" (25 mm)
ROLLERS AND LEVELING LEGS
Leveling legs near each front corner of the refrigerato r
are adjustable. They firmly position the refrigerator
and prevent it from moving when the doors are
opened. Leveling legs should be set so the front of the
refrigerator is raised just enough that the doors close
easily whe n opened about half,ray.
Turn the leveling legs clockwise to raise the
refrigeratm; counterclockwise to lower iL
Rollers next to the leveling legs allow you to move the
refrigerator away from the wall for cleaning.
Turn the legs counterclockwise until the weight of the
refrigerator is transferred from them to the rollers,
After rolling the refrigerator back into place, turn the
legs clockwise until the legs again bear the weight of
the refrigerator.
14

Installation Instructions
HINSTALLING THE WATER LINE (ON SOME MODELS)
BEFORE YOU BEGIN
Recommended copper water supply kits are WX8X2,
WX8X3 or WX8X4, depending on the amount of
tubing you need. Approved plastic v_-ater supply lines
are GE SmartConnec( "_Refrigerator Tubing
(WX08X10002, WX08X10006, WX08X10015 and
WX08X10025).
When connecting your refrigerator to a GE Reverse
Osmosis Water System, the only approved installation
is with a GE RVKit. For other reverse osmosis water
systems, follow the manufacturer's recommendations.
This w-ater line installation is not ,a-arranted by the
refi'igerator or icemaker manufacturer. Follow these
instructions carefully to minimize the risk of expensive
water damage.
Water hammer (water banging in the pipes) in house
plumbing can cause damage to refrigerator parts and
lead to water leakage or flooding. Call a qualified
plumber to correct v_-ater hammer befbre installing
the water supply line to the refi'igeraton
To prevent burns and product damage, do not hook
up the water line to the hot water line.
If you use your refrigerator before connecting the
water line, make sure the icemaker power switch is
in the 0(Off) position (on power switch models) or
the feeler arm is in the STOP(up) position (on feeler
arm models).
Do not install the icemaker tubing in areas where
temperatures fall below fi'eezing.
When using any electrical device (such as a power
drill) during installation, be sure the device is double
insulated or grounded in a manner to prevent the
hazard of electric shock, or is battel T powered.
All installations must be in accordance with local
plumbing code requirements.
WHAT YOU WILL NEED
• Copper or GE SmartConnect TM Refrigerator Tubing
kit, 1/4" outer diameter to connect the refi'igerator
to the water supply. If using coppel, be sure both
ends of the tubing are cut square.
To determine how much tubing you need: measure
the distance fi'om the water valve on the back of the
refi'igerator to the w-ater supply pipe. Then add 8"
(2.4 m). Be sure there is sufficient extra tubing
(about 8" [2.4 m] coiled into 3 turns of about 10"
[25 cm] diameter) to allow the refi'igerator to move
out from the wall after installation.
GE SmartConnecC' Refi'igerator Tubing Kits are
available in the following lengths:
2' (0.6 m) - WX08Xl0002
6' (1.8 m) - WX08X10006
15" (4.6 m) - WX08X100f5
25" (7.6 m) - WX08X10025
Be sure that the kit you select allows at least 8' (2.4 m)
as described above.
NOTE: The only GE approved plastic tubing is that
supplied in GE SmartConnect TM Refrigerator Tubing
kits. Do not use any other plastic water supply line
because the line is under pressure at all times. Certain
types of plastic will crack or rupture with age and
cause water damage to your home.
15

Installation Instructions
B INSTALLING THE WATER LINE (CONT.)
WHAT YOU WILL NEED (CONT.)
•AGE water supply kit (conVaining tubing, shutoff
valve and fittings listed below) is available at extra
cost from your dealer or fi'om Parts and Accessories,
800.626.2002.
•A cold water supply. The water pressure must be
between 20 and 120 p.s.i. (1.4-8.1 bar).
•Power drill.
• 1/2" or adjustable wrench.
•Straight and Phillips blade screwdriver.
•Two 1/4 "outer diameter compression nuts and
2 ferrules (sleeves)--m connect the copper tubing
to the shutoff valve and the refrigerator ,_-ater valve.
OR
• If you are using a GE SmartConnec( _ Refi'igerator
Tubing kit, the necessa W fittings are preassembled
to tile tubing.
• If your existing copper ,a-ater line has a flared fitting
at the end, you will need an adapter (available at
plumbing supply stores) to connect the water line to
the refi'igerator OR you can cut off the flared fitting
with a tube cutter and then use a compression
fitting. Do not cut formed end from GE
SmartConnec( _ Refi'igerator tubing.
• Shutoff valve to connect to the cold water line.
The shutoffvalve should have a water inlet with a
minimum inside diameter of 5/32" at the point of
connection to the COLD WATER LINE. Saddle-type
shutoff valves are included in many ,a-ater supply kits.
Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes.
Install the shutoffvalve On the nearest frequendy used
drinking water line.
[] SHUT OFF THE MAIN WATER
SUPPLY
Turn on the nearest faucet long enough to clear
the line of,a-ater.
[] CHOOSE THE VALVE LOCATION
Choose a location for the valve that is easily
accessible. It is best to connect into the side of
a vertical water pipe. When it is necessm T to
connect into a horizontal water pipe, make the
connection to the top or side, rather than at the
bottom, to avoid drawing off any sediment from
the water pipe.
[] DRILL THE HOLE FOR THE VALVE
Drill a 1/4" hole in tile water pipe (even if using
a sell:piercing valve) using a sharp bit. Remove any
burrs resulting from drilling the hole in the pipe.
Take care not to allow water to drain into the drill.
Failure to drill a1/4" hole may resuh in reduced
ice production or smaller cubes.
16

Installation Instructions
[] FASTEN THE SHUTOFF VALVE
Fasten tile shutoffvalve to tile cold water pipe with
the pipe clamp.
PipeClamp_
Saddle-Type_4
ShutoffValve VerticalCold
WaterPipe
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered m. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumbm:
[] TIGHTEN THE PIPE CLAMP
Tighten the clamp screws until the sealing washer
begins to swell.
NOTE: Do not overtighten or you may crush the
tubing. Washer
PipeClamp-- _lnlet End
Clam[
[] ROUTE THE TUBING
Route the tubing between the cold water line and
the refrigerator.
Route tile tubing through a hole drilled in tile wall
or floor (behind the refrigerator or adjacent base
cabinet) as close to tile wall as possible.
NOTE: Be sure there is sufficient extra tubing
(about 8 feet [244 cm] coiled into 3 turns of about
10" [25 cm] diameter) to allow the refl'igerator to
move out from the wall after installation.
[] CONNECT THE TUBING
TO THE VALVE
Place the compression nut and ferrule (sleeve)
for copper tubing onto the end of the tubing and
connect it to the shutuff valve.
Make sure the tubing is fully inserted into the
valve. Tighten the compression nut securely.
For plastic tubing from a GE SmartConnect ''_
Refrigeratur Tubing kit, insert the molded end
of the tubing into the shutuff valve and tighten
compression nut until it is hand tight, then tighten
one additional turn with a wrench. Overtightening
may cause leaks.
Nut
Saddle-Type
ShutoffValve ,_ SmartConnect_
Tubing
PackingNut /
/
OutletValve_ Ferrule{sleeve)
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered tu. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumbm:
[] FLUSH OUT THE TUBING
Turn the main ,a-ater supply on and flush out the
tubing until the water is clea_:
Shut the water offat the water valve after about
one quart (1 liter) of water has been flushed
through the tubing.
17

Installation Instructions
B INSTALLING THE WATER LINE (CONT.)
[] CONNECT THE TUBING TO THE
REFRIGERATOR
NOTES:
• Before making the connection to the refrigerator,
be sure the refrigerator power cord is not plugged
into the wall outlet.
•We recommend installing a water filter if your
water supply has sand or particles that could clog
the screen of the refrigerator's water valve. Install
it in the water line near the refrigeratol: If using
GE SmartConnec¢ "_Refrigerator Tubing kit,
you will need an additional tube (WX08X10002)
to connect the filter. Do not cut plastic tube to
install filten
Remove the access coven
Remove the plastic flexible cap from the water
valve (refrigerator connection).
Place the compression nut and fi_rrule (sleeve)
onto the end of the tubing as shown. On GE
SmartConnec¢" Refrigerator Tubing kit,
tile nuts are already assembled to the tubing.
Insert tile end of the tubing into the water valve
connection as far as possible. While holding the
tubing, tighten the fitting.
For plastic tubing from a GE SmartConnec¢"
Refrigerator Tubing kit, insert the molded end
of the tubing into the shutoff valve and tighten
compression nut until it is hand tight, then
tighten one additional turn with a wrench.
Overtightening may cause leaks.
[] CONNECT THE TUBING TO THE
REFRIGERATOR (CONT.)
Fasten the tubing into the clamp provided to
hold it in a vertical position. You may need to
pry open tile clamp.
1/4"Copper
Tubing TubingClamp
Refrigerator
Connection
Reattach the access corm,
1/4"Compression
Nut
{sleeve)
Tubing
[]TURN THE WATER ON AT THE
SHUTOFF VALVE
Tighten any connections that leak.
Reattach the access covm:
18

Installation Instructions
[] PLUG IN THE REFRIGERATOR
Arrange the coil of tubing so that it does not vibrate
against the back of the refrigerator or against the
wall. Push the refrigerator back to the wall.
START THE ICEMAKER
On power switch models, set the icemaker power
switch to the ! (on) position. On feeler arm models,
move the feeler arm to the ON (down) position. The
icemaker will not begin to operate until it reaches
its operating temperature of 15°F (-9°C) or below.
It will then begin operation automatically.
Powerswitchmodel
STOP(up)position
FeelerArmin
theON(down}position
Feelerarmmodel
NOTE: In lower water pressure conditions, the
water valve may turn on up to 3 times to deliver
enough water to the icemaker.
[] REVERSING THE DOOR SWING
IMPORTANT NOTES
When reversing the door swing:
•Read the instructions all the way through befbre
starting.
• Handle parts carefully to avoid scratching paint.
- Set screws down by their related parts to avoid using
them in the wrong places.
"Provide a non-scratching work surface for
the doors.
IMPORTANT: Once you begin, do not move the
cabinet until door-swing reversal is completed.
These instructions are for changing the hinges from
the right side to the left side if you ever want to change
the hinges back to the right side. follow these same
instructions and revm*e all references to left and right.
TOOLS REQUIRED
Phillipsscrewdriver Maskingtape
5/t6'<hex-head
socketdriver T20or T25Torxdriver,
wNc.heveryourmodel
requires
Putty knife or thin-
blade screwdriver 5/t6" open:end wrench
19

Installation Instructions
[] REVERSING THE DOOR SWING (CONT.)
[]BEFORE YOU START
1.1 Unplug the refrigerator fi'0m its electrical
outlet.
2.2 With a 5f 16" hex-head socket drivm; remove the
screws that hold the top hinge to the cabinet.
1,2 Empty all door shelves, including the dairy
comparrmem.
CAUTION: Do not let either door drop to the
floo_: To do so could damage the door stop.
2.3 Lift the hinge (and the shim glued to it) straight
up to fi'ee the hinge pin from the socket in
the top of the door and set it aside, along with
its screws.
T°pHinge_ I
2.4 Remove the tape and tilt the door away fi'om the
cabinet. Lift it off the center hinge pin.
[] REMOVE THE FREEZER DOOR
2.1 Tape the door shut with masking tape.
2O
2.8 Set the door on a non-scratching surface with
the outside up.
2.6 Using a Torxdrivm; transfer the 2 screws from
the opposite side of the cabinet to the screw
holes vacated by the top hinge removal.