GE ZIPP360NZA User manual

Pub. No, 49-60700
Part No. 224D3560P001
12-13 GE
monogram.com
Design Guide with
Installation
Instructions
36” Built-In French Door,
Bottom-Freezer Refrigerators

Safety Information
BEFORE YOU BEGIN
Read these instructions completely and carefully.
e IM PO RTANT — Save these instructions
for local inspector's use. Observe all governing codes
and ordinances.
« Note to Installer — Be sure to leave these
instructions with the Consumer.
e Note to Consumer — Keep these instructions
with your Owner's Manual for future reference.
WARNING:
This appliance must be properly grounded. See
“Grounding the Refrigerator,” page 9.
AVERTISSEMENT
Cet appareil doit 6tre correctement mis a Ia terre.
Consulter « Mise a la terre du réfrigérateur », page 9.
If you received a damaged refrigerator, you should
immediately contact your dealer or builder.
CAUTION:
Due to the weight and size of this refrigerator, and to
reduce the risk of personal injury or carnage to the
product—THREE PEOPLE ARE REQUIRED FOR PROPER
INSTALLATION.
PRUDENCE
A cause du poids et de la taille de ce réfrigérator et
pour réduire le risque de blessure et de dommages, IL
FAUT TROIS PERSONNES POUR FAIRE L'INSTALLATION
CORRECTEMENT.
Skill Level — Installation of this refrigerator requires
basic mechanical, carpentry and plumbing skills.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the GE Appliance Warranty. See the
Owner’s Manual for warranty information.
WARNING:
* These refrigerators are top-heavy and must
be secured to prevent the possibility of tipping
forward. Anti-Tip protection is required. See page 11
for details.
« Use this appliance only for its intended purpose.
« Immediately repair or replace electric service cords
that become frayed or damaged.
¢ Unplug the refrigerator before cleaning or making
repairs.
¢ Repairs should be made by a qualified service
technician.
AVERTISSEMENT
* Ces réfrigérateurs sont lourds en haut et il faut
les arrimer pour éviter leur basculement. II faut avoir
un systeme de protection contre le renversement.
Voir les détails page 11.
¢ || ne faut utiliser cet appareil que pour l'utilisation
appropriée.
* Réparer ou remplacer immédiatement tout cordon
électrique effiloché ou endommagé.
@ || faut débrancher le réfrigérateur avant le nettoyage
ou toute intervention.
* Les réparations doivent étre faites par un technicien
qualifié.
For Monogram local service in your area, call
1.800.444.1845.
For Monogram service in Canada, call
1.800.561.3344
For Monogram Parts and Accessories, call
1.800.626.2002.
www. monogram.com
CONTENTS
Planning Guide
installation Instructions
The
Installation
Space...
3
Tools,
Hardware,
Materials...
Step
8,
Adjust
Door
Swing
Dimensions
Gnd
ClEGrance
cececceccccsce: 3
Grounding
the
Refrigerator
Step
9,
Install
Grille
Panel.
130°
DOOF
SWING
veesesesssssssssssssesssesssscsseesetsee
4
Step
1,
Remove
Packaging...
Step
10,
Install
Framed
Panels.........
14
90°
DOOP
SWING.
oeccsccccccsccssececeeesssssssssesssesee
5
Step
2,
Install
Water
Line...
Step
10A,
Install
Overlay
Panels.......15
CUSTOMIZATION
BASICS
voces
6
Step
2A,
RO
Water
Line............
Step
11,
Connect
Water
Supply
.......
16
Panel
DIMENSIONS
..occccccecccceeccssseccesssesssseees
7
Step
3,
Install
Side
Panels
Step
12,
Connect
POWEP
ccs
16
Side
POMELS
cocccccccccccccccssesesccseeccssseessseseseeeeeeee
8
Step
4,
Install
Anti-Tip
Brackets........
11
Step
13,
Start
ICEMOKEP
ee
16
Step
5,
Level
Refrigerator
12
Step
14,
Install
Toekick
oe.
17
Step 6, Alternate Anti-Tip Procedure... 12
Step 7, Secure Refrigerator to
Cabinetry

Design Guide
THE INSTALLATION SPACE
35-1/2"
It—Finished Width —*
The finished 25/16" Wall View
cutout width oy
must be ee: .
35-1/2”
O°
\\
Electrical
1 Area
85" "F-24" Cutout Depth 75" From
Finished Floor to Bottom
Opening Water Supply of Electrical Area
f/o\
pty
.
Water And Electrical Locations
Electrical and water supply must be located
The cutout depth must be 24”
as shown.
The refrigerator will project forward, slightly beyond
adjacent cabinetry, depending on your installation.
Allow minirnum 1/8" air gap between case back & wall.
Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot exceed
the 24” installation depth shown. The top case trim
overlaps the bottom of the soffit.
Additional Specifications
A115 volt 60Hz., 15 or 20 amp power supply is required.
An individual properly grounded branch circuit or circuit
breaker is recommended. Install
a properly grounded 3-prong electrical receptacle
recessed into the back wall. Electrical must be located
on rear wall as shown.
Note: GFI (ground fault interrupter} is not recommended.
* Water line can enter the opening through the floor
or back wall. Route GE SrnartConnect™ kit or 1/4” 0.D.
copper tubing between the cold water line and the
water connection location. The tubing should be
long enough to extend to the front of the refrigerator.
Installation of an easily accessible shut-off valve in the
water line is required.
DIMENSIONS AND CLEARANCES
35" 25-3/8" Framed Models
Case Width 25-3/4" Stainless Steel Models
r— Case Depth
>|
* Shipping height. The
refrigerator can be
adjusted to fit into a
*84" From cutout that is 83-1/2”
oer ome min. to 84-1/2" max.
height. Note that the top
case trim at the front is
1/2” higher and will
overlap upper cabinetry
or soffit. Use leveling
-t. 36" Frame to legs and wheels for a
i - + . a .
Frame Width = maximum 1” height
Depth including Handles: adjustment.
27" Framed Models
27-13/16" Stainless Steel Models
28-5/8" Professional Style Models
Product Clearances
These refrigerators are equipped with a 2-position coor
stop. The factory set 130° door swing can be adjusted to
90° if clearance to adjacent cabinets or walls is restricted.
12-1/8" 12-1/8"
Min. to Min. to
Wall Wall
z
|
23-7/8"
Behind
Frame
ft +
—— I af
fo? ee LS I a I » Stainless &
va
7
PN
Sy
90°
By
90°
18-1/8
Pro
Madeis)
a wd van | ee yen
“130 Bo NS | UN, | |18-3/16" (frames
* ; mh Lhd
*4" Stainless and AA
Framed Models. «min. Distance
5” Pro Series to Wall
Allow 12-1/8” minimum clearance for a full 130° door
swing.
For a 90° door swing, allow 4” min. clearance to a wall,
for framed and stainless steel rnodels. Allow 5” min.
clearance for professional style models. If the 90° door
stop position is used, pan access is maintained, but pan
removal is restricted.
See illustrations pages 4 and 5 to determine door swing
interaction with adjacent cabinets or countertops.

Design Guide
Refrigerator
$
8
om
.2
E
<
£5
a
eS
ib
oO
&
ke
~
¢€
o%
@
Vv
a
HA
oO
Y
VoOoe
oa
5
Oo
os
vo
we
=
—
OOo
€
OO
ss
epaksgt
No
<
2oonEe8
&
=
jo
oe
VV
a5
&
>
1
2
Boxysess.
boi
ag
oe
®5,wo
re)
s
CO
Senna
se
oee
eee
pasenanse
nd
a
3
¢
as
=
1
1
a
5
oe
GES
x
hoi
gt
Sox
Bo
GS
SE
Qype
SS
Y
OBE
Gao
“Nw
Ho}
El
HT
&
“og
wee
eoe
Sralaeiaaleneieneleieneienaien
lanai
bowen
eben
a
“og
oO
a
a
=
,
.
wi
vos
fe
™N
st
' 1
i
3
=
.
foe
ONE
SEO
G
>
eee
eed
Oe
me
Ook
KR
ott
rrr
|
“
fie
eopte
Le
™“
er
“fe
Eee
sto
.:
a
4
5
o>
5
>50
Alen
eeeeee
eee
enneeeee
tees
tatehenapend
mo
.
>
&
ec
=
: ' ;
ae
uw
OF
=
bt
ee
jreecle
eden
ad
“
“eo
ae
oe
So
—_
=
’
a
aS
x
(ot
ot
few
Ll
oe
ee
eee
|
“
.
1
~
y y
£7
exe
7
—
&
bog
—_
oT.
~
ioe
,
-
ae
ST
ott
ests
ma
ae
Loe
3
a
a
-
—
'
“
,
yo
—
FFE
1
oa
fo
-
ye
.
fe
,
=
aoe
7
STs
Poe
oy
é
L
oo
a
a
ee
eee eee
ee
eee
‘
J
LP
—~
x
oe
E&
5
st
oo
5,2
Se
vere
ee
ee
4
ae
res
~
NL
eee)
OCD
mr
ces
BE
ge
€
82]
4
4
st
¢
>
«4
et
7
“
€
7
-
4
4
&
PP
y
ae
4
o
foe
o
S
a
”
OO
7
-
”
.
Yo
a
+
a7
a7
4
“4
ost
a
oO oO
a
Top View
130° DOOR SWING
(factory setting)
Scale 1 1

Design Guide
8
.
w@
oOo”g
y
2
©
fs
BHESEYER
ES
oe
Arcs
Voag
e%@oMrgc
C=
a
0
ovVrev
oe
®sS5
5,93
£%
GSEBESBPoOFFS
Eee
oee
eo
YS
OREnL
LS
o9Uvy
Cu
2G
=f
=—
Oe
E
eo
os
ss
oo
v
ve oH
Oo
EVGWv7#oS
Pe Ce
svotogves
.
C
OD
Cf
£0
mFoHaoOE
Soe
Ee
=
wo ws wm
Oo
Refrigerator
—
a
oS
So
ke
coagf Tee
ror
mm
ets
=<
NES
ro
1-1/4"
3/4" Overlay
Panel
(Nomina! Size}
Door
90° DOOR SWING
(optional setting)
Top View
Scale 1:1

Design Guide
CUSTOMIZATION BASICS:
Framed Or Overlay Panels, Custom Handles and Accessory Kits
Professional Style Stainless Steel Refrigerators
Stainless steel wrapped refrigerators with beveled edges
and professional style handles. These models are shipped
ready for installation.
Stainless Steel Wrapped Refrigerators
Stainless steel wrapped refrigerators with beveled edges
and tubular stainless steel handles that coordinate with
other Monogram appliances. These models are shipped
ready for installation.
Trimmed Refrigerators
Trimmed refrigerators are designed to be customized with
decorative panels. Field installed custom door and grille
panels are required.
Framed panels
You may install 1/4” thick custom panels from your
cabinet manufacturer. The decorative panel slides into the
factory installed trirn.
Framed Panel
Standard Door Handles
Standard supplied handles shown in 1/4” panel position.
Overlay panels
You may also choose to install custom overlay panels from
your cabinet manufacturer. This design provides
a seamless appearance which integrates smoothly
with surrounding cabinetry.
a
3/4" Overlay Panel edhe
.10" Thick Spacer Panel SS
1/4" Thick Backer Panel ~
Standard Door Handles
Standard supplied handles shown in 3/4” overlay panel position.
Door and Drawer Handles
The standard supplied handles can be adjusted to
accommodate both framed or overlay panels. Custom
handles of your choice, supplied by your cabinet maker
can also be installed on overlay panels.
Side Panels
Side panels must be used whenever the sides of the
refrigerator will be exposed.
Optional Accessory Kit
¢ ZKHPSS1: Professional Tubular Stainless Steel Handle
designed to fit 3/4” overlay panels. Kit includes one
handle. Order 3 kits for bottorn-freezer refrigerators from
your Monogram supplier.

Design Guide
1/4” FRAMED PANEL DIMENSIONS
ft osne
. *— Trim
If you choose to install framed panels, they must be cut Reveal
to the dirmensions shown. The panels will slide into the
frarne on the door, drawer and grille.
lf the custorn panelisless than 1/4" thickandifitfits te ae
loosely in the door frame, it can be backed up with a
piece of filler material or foam tape to irnprove the fit.
IMPORTANT NOTE: Maximum total
panel weight:
« Fresh food door panel - 30 Ibs.
« Freezer drawer panel - 28 lbs.
¢ Grille Panel - 11 Ibs.
| A | Framed Panel Dimensions
Grille Panel 8 A (Width) 8 (Grille Height) C (FF Height) D(FZ Height) —_& (FF Width)
4 1/4” Framed Panel 33-7/8" 8-7/8" 46-1/16” 21-7/8” 16-3/8”
<—E—* +E
Fresh || Fresh
Food || Food | ¢ Overlay Panel Dimensions
Panel || Panel A(Width) 8 (Grille Height) CIFF Height) =O (FZ Height) —€ (FF Width)
1/4” Backer Panel 33-7/8" 8-7/8" 46-1/16” 21-7/8” 16-3/8”
0.10” Spacer Panel 32-1/2” 7-5/8" 44-11/16” 20-1/2” 15°"
Freezer Drawer 3/4" Overlay Panel 34-1/8” 9” 46-5/16" 22" 16-5/8”
Panel
Wo
3/4” OVERLAY PANEL DIMENSIONS
For a more custom appearance, overlay panels may be
installed on trimmed models. The overlay panel must be
secured to a 1/4” thick backer panel which slides into the
trim. A spacer panel 0.10” thick must be placed between
the overlay and backer panel.
Assemble the panels with glue and screws.
* Center the spacer panel on the backer panel, left to
right and top to bottom. Secure the panels with glue.
* Center the spacer and backer panel on the overlay
panel and secure with glue and screws. Screws must
be countersunk into the backer panel.
IMPORTANT NOTE: Maximum
total weight for the assembled
panels:
« Fresh food door panel - 30 Ibs.
* Freezer drawer panel - 28 lbs.
¢ Grille Panel - 11 Ibs.
NOTE: Left-to-right offset is not always equal to
top-to-bottom offset.

Design Guide
SIDE PANELS .
* Depending on
Side panels must be used whenever the sides of the installation height.
refrigerator will be exposed. The 1/4” side panels will
slip into the side case trim. Secure the panels to the
refrigerator with stick-on hook and loop fastener strips.
Order the side panels from the cabinet manufacturer.
* Cut a notch in the top front corner as shown to allow
clearance for corner keys in the front side trim.
1
i
2-9/16"

Installation Instructions
TOOLS REQUIRED
¢ Tinsnips to cut banding
e Stepladder
* Bucket
* Level
¢ Appliance Hand Truck
¢ Tubing cutter
« 7/16” open-end wrench
e #2 Phillips screwdriver
¢ Drill and appropriate bits
« 5/16”, 7/16” socket
* Safety glasses
« 1-1/4” open end wrench
* Pliers
« 1/4” ratchet
HARDWARE SUPPLIED
e Water filter bypass plug
e Anti-Tip brackets
« 1/4” nut and ferrule
MATERIALS REQUIRED
¢ 35” long 2x4 for Anti-Tip support
« 1/4” copper water line tubing or GE SmartConnect™
Refrigerator Tubing kits
« Water shut-off valve
* Custom panels for fresh food door, freezer drawer
and grille panel
* Screws to secure refrigerator to cabinetry.
* Stick-on hook and loop fastener strips for
1/4” side panels
FLOORING
For proper installation, this refrigerator must be placed
on a level surface of hard material that is at the same
height as the rest of the flooring. This surface should
be strong enough to support a fully loaded refrigerator,
or approximately 1,200 Ibs.
NOTE: Protect the finish of the flooring. Cut a large
section of the cardboard carton and place under the
refrigerator where you are working.
GROUNDING THE REFRIGERATOR
IMPORTANT—(Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard three-prong (grounding) wall receptacle
to minimize the possibility of electric shock hazard
from this appliance.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
Where a standard 2-prong wall outlet is encountered, it
is your personal responsibility and obligation to have it
replaced with a properly grounded 3-prong wall outlet.
DO NOT, UNDER ANY
CIRCUMSTANCES, CUT
OR REMOVE THE THIRD
(GROUND) PRONG FROM
THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT THE
REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.

Installation Instructions
STEP 1} REMOVE PACKAGING
CAUTION: Refrigerator is much heavier at the
top than at the bottorm—be careful when moving. When
using a hand truck, handle from side only.
PRUDENCE: ie réfrigérateur est beaucoup
plus lourd en haut qu’en bas. Il faut étre prudent lors
des déplacements. Si un ciable est utilisé, il faut soulever
le réfrigérateur sur le cdté seulernent.
¢ Carefully cut banding at the top and bottom,
remove outer carton.
* Slide out back corner posts (2).
* Slide carton off top of cabinet.
NOTE: IT IS NOT NECESSARY TO LAY CABINET DOWN IN
ORDER TO REMOVE SKID!
e The unit is secured to the skid with 2 full-length
tie-down straps. Remove the ten 5/16” bolts from the
base channels in the tie-downs.
e Remove the four 7/16”
bolts securing the straps
to the skid.
CAUTION: vo not
ATTEMPT TO ROLL UNIT
OFF SKID.
PRUDENCE: i ne
FAUT PAS ESSAYER DE FAIRE
ROULER LE REFRIGERATEUR
POUR L’ENLEVER DE LAY
PALETTE.
Remove 5
, base channel!
bolts on each
side
Remove 2 strap
bolts on each side
¢ Support blocks on the bottorn of the refrigeration
case must be removed before the refrigerator is
taken off the skid or damage will occur. Carefully,
tilt refrigerator and slide blocks out frorn beneath.
* Remove toekick. Set aside for final installation.
* Lift the refrigerator off the skid with an appliance
dolly. Handle from the sides.
STEP 2| INSTALL WATER LINE
¢ A cold water supply is required for automatic
icemaker operation. The water pressure must be
between 40 and 120 p.si.
@ Route 1/4” OD copper or GE SmartConnect™ plastic
tubing between house cold water line and the water
connection location.
¢ Tubing should be long enough to extend to the front of
the refrigerator. Allow enough tubing to accommodate
bend leading into the water line connection.
NOTE: The only GE-approved plastic tubing is supplied
in the GE SmartConnect™ Refrigerator Tubing kits. Do not
use any other plastic water supply line because the line
is under pressure at all times. Other types of plastic may
crack or rupture with age and cause water damage to
your home.
GE SmartConnect™ Refrigerator Tubing Kits are available
in the following lengths:
276m) Wx08X10002
6 (1.8m) Wx08X10006
15 ft (4.6 m) WxX08X10015
25 ft (7.6 m) WX08X10025
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the line
of water.
« Install a shut-off valve between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be
easily accessible.
Floor
‘Waterline Tubing
¢ Turn on the main water supply and flush debris.
Run about a quart of water through the tubing into
a bucket. Shut off water supply at the shut-off valve.
NOTE: Saddle type shut-off valves are included in
many water supply kits, but are not recommended
for this application.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
10

Installation Instructions
STEP 2A) WATER LINE INSTALLATION WITH
A REVERSE OSMOSIS SYSTEM
Skip this step when not using an RO System
If the water supply to the refrigerator is frorn a Reverse
Osmosis Water System, use the refrigerators filter bypass
plug. Using the refrigerator’s water filtration cartridge with
the RO filter can result in hollow ice cubes.
Ll
Clit
| sweon
Filter Bypass Plug
STEP 3] INSTALL SIDE PANELS
Skip this step when not using side panels
if you are using 1/4” side panels, they should be inserted
into the case trim. Fasten the panels to the refrigerator
with stick-on hook and loop fastener strips before setting
refrigerator in place.
11
STEP 4| INSTALL ANTI-TIP BRACKETS
WAR N | NG: ANTI-TIP PRECAUTIONS
The refrigerator is top-heavy and must be secured to prevent the
possibility of tioping forward.
ATTENTION: precautions contre Les
BASCULEMENTS
Le réfrigércteur est beaucoup plus lourd en haut et il faut le
maintenir en place pour éviter la possibilité de son basculement
vers l'avant.
* Cut a 2” x 4” x 35” block and secure the block to the
mounting brackets provided using #12 or #14 wood screws.
2x4Cut a
35" Length it i i
Installation Mounting
Height Bracket
From Floor
Screws Mounted into~
Vertical Wall Studs
e Secure the bracket with wood block to the back wall so that it is
84” (or your installation height) from the finished floor. Use #12
or #14 wood screws. See illustration.
Brackets
Required
Brackets
Not Require
Beneath a
Soffit
Side View
e Screws must penetrate cit least one inch into vertical waill studs.
¢ Before pushing the refrigercitor into the opening, plug the power
cord into the receptacle. Open the grille panel and reach into
the opening at the back to grasp the power cord. Pull the power
cord into the opening as you push the refrigerator back.
e Gently push refrigercitor into the opening with hands against
front corners.
Important Note: When the refrigerator is installed under a soffit or if
there is not enough height for this method of security, brackets cannot
be used. Proceed to step 5 to level the refrigerator and then to step 6
to secure refrigerator to cabinets. The refrigerator must be secured to
prevent tipping.

Installation Instructions
STEP 5|LEVEL REFRIGERATOR
All models have 4-point leveling. The front is supported
by leveling legs, the rear is supported by adjustable
wheels. Both are accessible from the front of the
refrigerator.
@ To level the back of the refrigerator, turn the 7/16” hex
nut located above the front wheels. Turn clockwise to
raise or counterclockwise to lower the refrigerator.
« For front leveling, use a 1-1/4” open-end wrench.
* Adjust height of refrigerator to match installation
cutout opening 83-1/2 to 84-1/2”. The refrigerator
should be level and plumb with cabinetry.
—
Hex Nut Adjusts ~5,
Rear Wheels ba
SES) Tt
fo Leveling Leg
The rear leveling wheels and front leveling legs are
CAUTION:
lirnited to a maximum height adjustment of 1”. If the
installation requires more than 84-1/2” height, the
installer should elevate the refrigerator on a sheet
of plywood or runners. Cabinetry trim could also be
added across the top of the opening to shorten the
opening. If you attempt to raise the refrigerator more
than 1”, you will damage the front leveling legs and the
rear leveling wheels.
PRUDENCE
Les roues de nivellement arriére et les pattes de
nivellement avant permettent un réglage maximal
de 25 mm (1 po). Si l’ouverture pour le réfrigérateur
a une hauteur supérieure a 2,15 m (84-1/2 po),
Vinstallateur doit élever le réfrigérateur sur une feuille
de contre-plaqué ou des glissieres. Il est égalernent
possible d’ajouter des baguettes de finition des
placards sur le haut de l’ouverture afin de la réduire.
Lever le réfrigérateur de plus de 25 mm (1 po)
encommage les pattes de nivellement avant
et les roues de nivellement arriére.
12
STEP 6| ALTERNATE ANTI-TIP
PROCEDURE
The refrigerator must be secured to prevent tipping.
The anti-tip brackets cannot be used on metal wall
studs. Use this Alternate Procedure to secure the
refrigerator against tip-over whenever metal wall
studs are encountered and there is no soffit.
Aspe View
Top
Case
Trim
.
<P
a
S r
t
NN \ /
— \ / a
ae
Install Four
1-1/2" Drywall Screws
Through Trim and Into Soffit
or 3/4" Min. Wood Brace
¢ Raise the grille panel to access case trim.
« Use a 3/16” bit to drill four evenly spaced clearance
holes through the metal top case trim.
« Use a 1/16” bit to drill to pilot holes through the metal
clearance holes and into the wood soffit. The holes
should be centered in the soffit or a 3/4” min. wood
brace. The brace spanning the enclosure must be
securely fastened to cabinets on both sides.
« Install four, 1-1/2” drywall screws into the pilot holes.
STEP 7 |SECURE REFRIGERATOR
TO CABINETRY
Whenever possible, perform this step for anti-tip
security, or when anti-tip brackets cannot be used.
The refrigerator must be secured to prevent tipping.
* Raise the grille panel to access case trim.
® Drill hole in trim and drive screw through the trim into
adjacent cabinet.
¢ Follow the sarne procedure on the opposite side.
IL
Drive screws through case trim
and into adjacent cabinets.

Installation Instructions
STEP 8 | ADJUST DOOR SWING
NOTE: This refrigerator has a 2-position door stop.
When space does not allow the door to swing open
fully to 130°, you may change the door swing to a 90°
opening. Skip this step if door opening is satisfactory
for your installation situation.
e Lift the grille panel to access the wire cover trim.
e Remove screws on both sides of the wire cover trim
and rotate off.
e Use pliers to unscrew door stop anc reinstall into the
90° position.
I
Ip
Remove wire cover
trim screws
Pin Location For
Pin Location
as Shipped
130 Door Swine
e Reinstall the wire cover trim.
13
STEP 9} INSTALL GRILLE PANEL
¢ Raise the grille panel to stop position.
SS <1
Ea od —l
Foy Bee eee sees eee ee)
es Ge Be ed Ge Ge Ge ee ed ee
Bee ee eee seem eee),
| ceca 2
Loosen Seems raters ae || LOOSE
Side Side
a Trim
| I / Screw
Adjust Nut Below Spring to
Accommodate Panel Weight
Trim
Screw
|
* Loose screws on side trim behind frame. Rernove
bottorn trim.
¢ Slide panel over the metal backer panel and into
the trim.
* |f necessary, tap with a wood block until panel slips
under the top trim piece.
e Reassermble bottorn trim. Tighten screws.
e Adjust the hinge spring to accommodate the panel
weight, if necessary.

Installation Instructions
STEP 10| INSTALL 1/4” FRAMED PANELS IF YOU ARE INSTALLING OVERLAY PANELS,
| Gm...
ee
Use
Rear
Holes
to Secure Handle
Install door and drawer panels:
~~! Use Front Holes
to Secure Trim
GO TO STEP 10A.
Handle
Trim _
sw
Door Trim
de
Refrigerator
Door
LAA AAAS
Standard supplied handle shown
in 1/4” panel position.
* Open door to 90°. Rernove the 4 Phillips head screws * There are two sets of holes in the handle side trim.
frorn the door handle.
e Remove handle. Retain all screws.
e Remove 4 screws holding trim, lift off trim.
Retain screws.
e Slide framed panel into the door trim.
Replace handle side trim by installing the original screws
in the FRONT screw holes.
* Secure the handle to the door using the REAR
screw holes.
* Follow the same procedures to install the second door
panel and the drawer panel.
14

Installation Instructions
STEP 10A| INSTALL OVERLAY PANELS
Handle
Trim
_
;
Move
Forwar
For
3/4
Pane
“fe
Use
Front
Holes
SL.
to
Secure
Handle
~~
“Use
Rear
Holes
to
Secure
Trim
Supp
Right hand models shown.
for left hand models.
ea Door Trim
Refrigerator
Door
LARA AA
lied handle shown in the
overlay panel position.
Install door and drawer panels:
* Open door to 90°. Rernove the 4 Phillips head screws
from the door handle.
* Remove handle. Retain all screws.
* Remove 4 screws holding trim, lift off trim.
Retain screws.
¢ Slide overlay panel into the door trim.
Use the same instructions
e There are two sets of holes in the handle side trim.
Replace handle side trim by installing the original screws
in the REAR screw holes.
* Secure the handle to the door using the FRONT
screw holes.
* Follow the same procedures to install the second door
panel and the drawer panel.
Custom handles
If you are using custom handles, the hancie must be
properly secured to the panel before sliding the panel
into the trim.
* The cabinet manufacturer will supply the custom
handle and hardware.
« Secure the door/drawer trim using both the FRONT
and REAR screw holes. Discard supplied handle.
15

Installation Instructions
STEP 11 |CONNECT WATER SUPPLY
\ House
Water Supply
Refrigerator /
Water Supply
* Locate and bring tubing to the front of the cabinet.
¢ Turn the water on to flush debris from line. Run about
a quart of water through tubing into a bucket, then
shut off water.
Copper Tubing:
Slip a 1/4” nut and ferrule (provided) over both ends
of the copper tubing. Insert tube into the union fitting
on the unit and tighten nut to union.
® Turn on the water to check for leaks.
GE SmartConnect™ Tubing:
* Insert the molded end of the tubing into the
refrigerator connection. Tighten the compression nut
until it is just hand tight.
¢ Tighten one additional turn with a wrench.
Overtightening can cause leaks!
* Turn on the water to check for leaks.
Note: Make sure excess tubing length does not
interfere with drawer closing or toekick installation.
16
STEP 12 |CONNECT POWER
* Check to be sure the power cord is plugged into the
receptacle.
Sb <l
{
a |S
o E
Lo 4:
|
Electrical |
Outlet Master
Light Switch
* Check to make sure power to refrigerator is on by
opening refrigerator door to see if interior lights are
on.
e The temperature controls are preset at 37°F
for the fresh food section and O°F for the freezer.
e Allow 24 hours to stabilize before making
adjustments.
STEP 13 |START ICEMAKER
e Flip the switch to | (ON). The icemaker will begin
operation automatically.
¢ Be sure nothing interferes with the sweep of
the feeler arm.
¢ Discard the first full bucket of ice cubes.
¢ To turn the icemaker off, set the switch to O (OFF).

Installation Instructions
STEP
14]
INSTALL
TOEKICK
INSPECT
FINAL
INSTALLATION
* Locate the supplied toekick (shipped taped to
the side of the refrigerator]. Install the toekick
assembly with the 3 screws provided, adjust to the
desired height and tighten the screws.
Check door alignment
Stand back away from the refrigerator to inspect the
final installation.
¢ Installation or the addition of heavy door panels
ray have caused the doors to move slightly out of
alignment. Check to be sure the top of the doors are
evenly aligned with each other. If necessary, the doors
may be adjusted up or down to align.
« Add or subtract shims as shown to adjust the right
door only. More shims are located under the hood on
the left side in the bag with the filter bypass plug and
rini manual.
* A custom toekick can be installed to match or
complement the surrounding cabinetry. Use the
supplied toekick as a template to cut the shape.
IMPORTANT: The gap between the bottom of the . .
refrigerator cabinet and the top of the toekick must To Raise Right Hand Door
remain unobstructed for proper air circulation. ° Lift the right hand door up so there is a gap below the
bottom hinge bushing.
e Snap a shim onto the hinge pin below the bushing.
¢ Lower the door and re-check the alignment.
e Repeat as necessary.
To Lower Right Hand Door
e Lift the right hand door up so there is a gap below the
bottom hinge bushing.
e Remove a shim by pushing shim off of the hinge pin.
¢ Lower the door and re-check the alignment.
e Repeat as necessary.
s~ Bag location
17

Notes
18

Notes
19

Pub. No. 49-60700
Part No. 224D3560P001
12-13 GE
NOTE: While performing installations described in this book,
safety glasses or goggles should be worn.
For Monogram® local service in your area, call
1.800.444.1845,
NOTE: Product improvement is a continuing endeavor
at General Electric. Therefore, materials, appearance and
specifications are subject to change without notice.
GE Consumer & Industrial
Appliances
General Electric Company
Louisville, KY 40225
GEAppliances.com