Gefen HDMI 1000HD User manual

HDMI • 1000HD
USER MANUAL
www.gefen.com

Technical Support:
Telephone [phone]
[phone]
Fax [phone]
Technical Support Hours:
9:00 AM to 5:00 PM Monday through Friday.
Write To:
Gefen Inc.
C/O Customer Service
6265 Variel Ave.
Woodland Hills, CA91367-9897
Notice
Gefen Inc. reserves the right to make changes in the hardware, packaging and any
accompanying documentation without prior written notice.
The HDMI 1000 is a trademark of Gefen Inc.
© 2006 Gefen Inc., All Rights Reserved
ASKING FOR ASSISTANCE

TABLE OF CONTENTS
Introduction
Front Panel Descriptions
Back Panel Descriptions
How To Connect The HDMI 1000
How To Connect The HDMI 1000 (w/o DDC)
HDMI 1000 Wiring Diagram
Specifications
Warranty
1
2
3
4
5
6
7
8

READ THESE NOTES BEFORE INSTALLING
OR OPERATING THE HDMI 1000
• The fiber optics cable must be treated carefully when connectors are exposed. They
are susceptible to dust which can contribute to loss of pixels.
• The HDMI 1000 works for all HDMI displays and supports resolutions up to
1920x1200 or 1080p
• The HDMI 1000 is housed in a metal box for better RF shielding.
• Fully HDMI 1.2 compliant
• Uses CAT-5 cable for HDCP/DDC and control signals.
OPERATION NOTES

INTRODUCTION
Thank you for purchasing Gefen’ s ex•tend•it HDMI 1000. The HDMI 1000 allows exten-
sion of HDMI up to 1640 feet without losing any quality.
CONTENTS
The HDMI 1000 consists of:
--- (1) HDMI 1000S
--- (1) HDMI 1000R
--- (1) HDMI cable (6FT)
--- (1) 12VDC Power Supply
--- (1) User's Manual
1

HDCP & DDC Signals
HDMI 1000 Sender (Front View Only)
Blue
Green
Red Clock
Status LED indicates a link
between the sender and receiver
HDCP & DDC Signals
Blue
GreenRed Clock
Status LED indicates a link
between the sender and receiver
FRONT PANELS DESCRIPTIONS
Power LED indicates the unit is powered
HDMI 1000 Receiver (Front View Only)
Power LED indicates the unit is powered
2

12 VDC Input
HDMI 1000 Sender (Rear View Only)
HDMI Input
BACK PANELS DESCRIPTIONS
HDMI 1000 Receiver (Rear View Only)
3
12 VDC Input
HDMI Output

Connect the HDMI 1000 sender unit to the HDMI source using the supplied cables.
Connect the HDMI 1000 receiver unit to your HDMI display.
Connect the four fiber optics and one CAT5 cable between the sender and receiver.
Plug the 12VDC power supplies into the HDMI 1000 receiver.
You should see a beautiful picture.
* Cable Requirement - 50 or 62.5 micron multimode fiber optics cable
HOW TO CONNECT THE HDMI 1000
1
2
3
4
5
4

Connect the HDMI 1000 sender unit to the HDMI source using the supplied cables.
Connect the HDMI 1000 receiver unit to your HDMI display.
Connect the four fiber optics between the sender and receiver.
Plug the 12VDC power supplies into the HDMI 1000 sender.
Plug the 12VDC power supplies into the HDMI 1000 receiver.
If using a HDMI Detective attatch it inbetween the computer and the sender
You should see a beautiful picture.
* Cable Requirement - 50 or 62.5 micron multimode fiber optics cable
HOW TO CONNECT THE HDMI 1000 (w/o DDC)
1
2
3
4
5
6
7
The HDMI 1000HD can be hooked up without using the CAT5 if DDC is not needed. A
second power supply will be required to power the reciever unit in this setup.
For computer extensions where EDID is needed, a HDMI Detective can be purchased
to store the EDID of the display.
5

HDMI 1000 WIRING DIAGRAM
6