3
www.geiger.de
EN
2.1 Learning a transmitter
The order sequence is specied: the rst input on a transmit button receives the function UP, the
second input the function DOWN.
1. Hold the transmitter to be learned directly to the receiving antenna and press a key about
3 seconds until an audible signal is emitted. The learning mode is activated.
2. Keep holding the transmitter to the receiving antenna and activate briey the key for the UP
command. The radio code is learned and an audible signal is emitted for acknowledgement.
The control returns to normal operating mode.
2.2 Deleting the learned transmitter
1. Hold any transmitter directly to the receiving antenna and actuate a key about 3 seconds until
an audible signal is emitted. The control has changed over to learning / deleting mode.
2. Hold the transmitter directly to the receiving antenna and actuate any key about 5 seconds
until a long tone is emitted. All stored radio codes - radio codes of the sensors as well – will be
deleted. Then the control returns to normal operating mode.
2.3 Interchanging of the relay assignment
1. Hold any transmitter directly to the receiving antenna and actuate a key about 3 seconds until
an audible signal is emitted. The control has changed over to the learning mode.
2. Hold the transmitter about one meter away from the receiving antenna and actuate a key once.
An audible signal is emitted.
3. Now hold the transmitter close to the antenna again and actuate a key. The relay assignment to
the directions UP and DOWN is changed and an audible signal is emitted. The setting is stored
and the control returns to normal operating mode again.
2.4 Learning of the motor running time and of the lamellae setting angle
1. Power off and on the mains voltage (available time: 30 minutes!)
2. Hold the hand-held transmitter close to the antenna and keep a button depressed for approx.
3 sec. till an audible signal resounds (long tone). In order to adjust directly the control, keep the
white button on the controller depressed for approx. 3 sec.
3. IMPORTANT! Keep the hand-held transmitter at least 2 meters away from the controller.
4. Keep the UP button (or ext. button In1) depressed in order to retract the blind completely.
5. Upon reaching the upper limit position actuate briey the DOWN button (or ext. button In2)
6. Then press the button DOWN (or ext. button In2) for about 2 seconds - the blind moves down
automatically.
7. Actuate shortly button UP when the lower end position or the desired end position is reached
8. After completion of the running time learning procedure, the control changes over all auto-
matically to the lamellae setting angle learning mode.
9. Briey actuate the UP / DOWN buttons (or ext. buttons IN1/IN2) to set the desired angle
10. Hold again the hand-held transmitter close to the antenna and keep a button depressed for
approx. 3 seconds (or keep the white button directly on the control depressed for approx.
3 seconds).
11. Motor running time and lamellae setting angle are now learned and stored.
2.5 Subsequent modication of the lamellae setting angle
1. Power off and on the mains voltage (available time: 30 minutes!)
2. Actuate button DOWN (or ext. button IN2) to move the blind down to the end position
3. Hold the hand-held transmitter close to the antenna and keep a button depressed for approx.
3 sec. till an audible signal resounds (long tone).
4. IMPORTANT! Keep the hand-held transmitter at least 2 meters away from the controller.
5. Briey actuate the UP / DOWN buttons (or ext. buttons IN1/IN2) to adjust the desired angle
6. Hold again the hand-held transmitter close to the antenna and keep a button depressed for
approx. 3 seconds (or keep the white button directly on the control depressed for approx.
3 seconds).
2.6 Funksensoren
The control is able to learn the radio codings of two different sensors. In the event a sensor
coding has been learned, the control responds, provided the related sensors have been coded
accordingly, to the reception of the following radio sensor commands: „sun“, „evening twilight“,
„wind“, „rain“ and „service“.
• Upon the reception of the sensor command “sun too bright” an extend command is triggered
provided that the sun automatic function is enabled. The „retract“ command will be issued upon
the reception of the sensor command “sun dark”.
• Upon the reception of the sensor commands „wind“ or „service“, a retract command is triggered
and a certain pre-programmed disable time starts running. No operation can take place during
the disable time, as both the sun and the twilight sensor are disabled.
