Genee World G-Touch User manual

G
e
n
e
e
W
o
r
l
d
Touch
User Manual
Please retain this manual properly for future reference

Contents
Installation requirements 1
Notes 2 - 3
Introduction and Features 3 - 4
Basic Operations 4
Software Installation and Calibration 5 - 9
OSD Menu Introduction/ Passageway Selection 10
Screen Menu 11 - 25
Remote Control Functions 26
Control Panel 27
Interface Panel 28
PC Mode (VGA Input) specications / USB Mode 29
Trouble-shooting 30 - 32
Serial Control 33

01
The Load-bearing of the mounting rack:
Please choose the rack or sliding saddle specied by the manufacturer. Make
sure that the home-made rack’s bearing capacity and also the bearing capacity of
the support platform, is 4 times more than the actual weight capacity. Keep the LED
Interactive Multi-touch Display stable at all times.
The load-bearing of the mounting surface:
The bearing capacity of the mounting surface needs to be 4 times more than the
actual weight capacity. Make sure that the material of the mounting surface is
stable enough and consists of a strong material.
Heat Dissipation
Cooling Requirements The distance from the mounting surface (cm)
Nominal Power Left/ right side Top Bottom Back
Above 100W 10 20 20 10
Tips: Keep the air owing and make sure that the vent hole area of the top, left/right side
and bottom are no less than 50% of the sealing area, if the LED interactive multi-touch
display will be installed into a wall or box.
Installation Requirements

02
• All electronic components should be installed or placed out of children's reach
• Do not use other power cords except for what is provided with the screen
• Do not attempt to repair anything, without consulting a qualied technician
• Make sure the line voltage corresponds to the power of the receiving host
before use. Unplug the receiving host when unused for long periods of time
• Must use the three-phase power socket and make sure there is a ground
contact
• Do not install or place the device near any heat sources, such as a furnace, heat
transfer tube, power amplier, etc. Do not expose this device to direct sunlight,
dust and moisture. Do not install the device in any place which may have
mechanical vibrations or could lead to a vulnerable strike. For better
performance, it should be placed far away from high voltage transmission grid,
large metal objects and so-on
• Disconnect the power immediately and unplug when there is abnormal sound
or smell in the device. Do not use the device and call the qualied service
personnel for maintenance
• There should not be any liquid or other metals in the device. If any, power o
and disconnect the power and call the qualied service personnel
• Do not use any chemical reagent for the device’s body cleaning as it may result
in deterioration or damage to the paint. For any dust or dirt, use a warm cloth
and clean it after power disconnected. The IR Touch LED Display should be
gently wiped down with a clean soft cloth, when dirty
• Do not turn on and o the device frequently as it will shorten the service life of
the device. Turn on the device three minutes later after a normal power o
• Do not set the brightness and contrast ratio to maximum in long term so as to
lengthen the service life of the device
• Do not place the device on an unstable stand bracket or desk, or else the
device might tip over and get damaged
• Take extra care when moving the device to avoid any damage to the screen
• Should follow the operation manual of the manufacturer and install this device
and should only use the accessories for installation recommended by the
manufacturer
• The wall mounting of the device is only applicable on a cemented wall, solid
masonry wall and a wood siding wall that could bear more than three times
the weight of the device and should also be good for ventilation. For other
walls such as a Steel structure wall or one with a hollow structure or a glass or
marble wall. The walls ability to bear the device should be analysed to make
sure that there will be reduced risks.
Key Notes:
Notes

03
Introduction
The LED interactive multi-touch display is a multi- function teaching device with
functions of interactive teaching *digital demo *multi-media presentation *touch
control operation and handwriting input. From design and production, it is feature rich and
produced with a focus on the education industry . This device has
the advantages of convenience for observing and operating, all-digital intelligent
control, writing *modifying and deleting freely on the screen with ngers or
light-proof objects. This interactive screen is the perfect device for modernized
interactive education & presenting.
Features:
• Design specically for both educational and business interactive presentations
• High brightness and contract ratio display and clearly visible in bright light or
indoor and outdoor environment
• One key power saving mode (the backlight brightness was lowered and power
saved) when there is a need for low brightness during operation
• With advanced IR scanning sensor technology and HID drive free, plug
and play
• The graphic processing is based on vector graphics with high compression
and no distortion etc
• Multiple pen types, line widths and colours
• Strong edit function and supports real-time editing
• Multiple backgrounds and supports custom backgrounds, free insert of
gures and images
• Intelligent recognition of geometric gures. With features of variety gures
recognition, high discrimination and multi- pen recognition etc
• Ink-brush simulation with vigorous and forceful calligraphy
• Written documents can be saved as formats in PDF, GIF, PNG, TIFF and BMP etc.
• Simulate mouse operation
• Dual-point touch and multi- nger roaming
• User management with functions of user adding and deleting, user switch over
and user customization etc. This enables the software conguration close to
user’s operation habits
• Support other apps
• Handwriting English, numbers and special characters recognition
Introduction & Basic Features

04
Basic Operations
Power On
• Power the Touch LED Display with 100~240V 50/60Hz AC
• Turn on the ship form switch on the bottom of the Touch LED Display (beside
the power interface) to power on (the indicator light is red)
• Press “Power” on the Touch LED Display or “Standby” on the remote control
to switch on the Touch LED Display (the indicator light is green now). Press
“Computer” to turn on the computer (only applicable to the model with built in
PC.
Basic Operating
Power O
• If you want to turn o the touch LED display temporary, press “Power” on
the touch LED display. Press“Computer” on the panel to turn o the
computer when it is in the ON status (only applicable to the model with
built in PC)
• If you want to turn o the touch LED display completely, turn o the ship
form switch on the bottom of the touch LED display (beside the power
interface) or unplug the power cord
• For the model with built in PC, turn o the PC and disconnect the power

05
Software Installation
Recommend system conguration:
CPU: Inter(R) Core i3 2.27GHz or AMD CPU with same performance
RAM: 1GB
Hard disk: 1GB free space
Video card: Support DirectX 9 or higher
Software Installation
• The touch LED display with built-in computer has installed the latest version of
the writing software by factory default and can skip the following steps
• HID free drive function is only applicable to Vista, Windows 7 or a higher
version (realize the functions of multi-touch etc.). The touch LED display with
Windows XP version should install/run the software for normal use
• Insert the ocial USB cable into the USB ports of the computer and touch
LED display
• Insert the ocial software installation disk into the computer.
• Select the inserted software, follow the instructions and complete the
installation of the touch LED display software
• The computer needs to then be restarted in order to activate the software after
the installation is completed. Then Save all the les in the computer and restart
Software Uninstallation
If you are sure to delete the touch LED display software from your computer, click
“Add or Remove Programs”in “Control Panel”. Choose “WPad” and click “Uninstall”
to uninstall.
Software Installation

06 Software Calibration
To function properly, the handwriting of the projected image on the touch LED
display should coincide with the actual one, aiding it to calibrate accurately. The
following situations need calibration.
• The touch LED display is used for the rst time.
• The drive has been reinstalled.
• The computer connected to the touch LED display has been changed
• The touch LED display is with nine-point calibration. Steps for calibration are as
follow:
1. Connect all devices necessary and run the touch LED display drive.
2. Click the drive icon of the touch LED display at the right bottom of the screen and
you can see the following:
3. Choose “9 Points” and click “calibrate”as shown below.

07
4. Vertically touch the centre of the ashing “+” with the touch LED display pen tip
until the ashing “+” moves to the next calibration point . Thus one point is
calibrated. Follow the instructions in the calibration interface and complete the
calibration of the other points. The software will return to the desktop automatically
at once. Calibration completed.
Calibration for Windows 7 version:
1. Connect the PC and writing screen touch USB port with the ocial USB cable.
2. Choose “Tablet PC Settings”in “Control Panel”.
Software Calibration

08
Table PC Set
Choose in Tablet PC Set window.
Table PC Set
Software Calibration

09
Vertically touch the centre of the ashing “+” with the writing screen pen tip
until the ashing “+” moves to the next calibration point and thus one point is
calibrated. Follow the instructions in the calibration interface and complete the
calibration of the other points.
Calibration Interface
Notes:
• For good writing accuracy, you should use the ocial pen to calibrate. Do not
calibrate with your nger
• Wrong calibration may lead to the abnormal function of the touch screen and
this requires re calibration
• Pressing “ESC” during calibration can cancel the current calibration operation
• There are minor dierences between the calibration interfaces of dierent
version software. Follow the instructions in actual interface and calibrate
Calibration Completed
Click “Yes”to complete calibration.
Software Calibration

OSD Menu Introduction
Passageway Selection:
Automatic detection of signal resource: turn on or no signal, our equipment will
automatically detect the signal resource and switch signal resource, the signal list
and the order are as bellow:
VGA 1, VGA2, VGA3, HDMI1, HDMI2, HDMI3.
1. Press “Signal Source”in the remote control to get the signal source list
2. Press to choose the desired signal passageway
3. Press “Conrm” to enter the passageway
10

Screen Menu 11
Picture
• Press / to choose picture menu, the options will be dierent based on the
kind of the signal resource
• Press / to choose
• Press “conrm”to adjust the option’s value
• Press “conrm”to get into submenu
• Press “menu” to return to previous menu
• Press “exit” to escape the menu
Press“menu”to display the menu. Press to choose a submenu.
Picture menu Sound menu Time menu Option menu
In the picture menu, we could choose picture mode, colour temperature, aspect
ratio, noise reduction, PC set. Press to choose the corresponding option.

12
Get into the picture mode menu, the
contrast, brightness, colour, sharpness
and tint will be displayed, you could press
/ to switch options if the mode is set to
“User”.
Picture mode
• Press / to choose the option
• Press / to adjust the option’s value
• Press “menu” to return to previous menu
• Press “exit” to escape the menu
Notice: The “tint” option will be active
only in the NTSC signal resource option.
Get into the “tint” menu; the three
options (red, green, blue) will be
displayed. Press / to switch options.
Colour Temperature:
• Press / to choose the option
• Press / to adjust the option’s value
• Press “menu” to return to previous menu
• Press “exit” to escape the menu
Screen Menu

13
When in the aspect ratio menu. 6 options will be displayed They are: auto, 4:3, 16:9,
zoom 1, zoom 2 and Just Scan. Press / to choose the option. The options may
be dierent based on the signal resource.
Aspect ratio mode
• Press / to choose the option
• Press / to adjust the option’s value
• Press “menu” to return to
previous menu
• Press “exit” to escape the menu
Get into the submenu of Noise Reduction, you could choose low, middle, high
option, press / to choose the option.
• Press / to choose the option
• Press / to adjust the option’s value
• Press “menu” to return to
previous menu
• Press “exit” to escape the menu
Screen Menu

14
When in the submenu of PC set. There will be ve options: auto adjust, horizontal
position, vertical position, size, phase. Press / to choose the option.
When in the sound menu, there will be six options: sound mode, balance, auto
volume, surround sound, SPDIF mode, EQ. Press / to switch options.
• Press / to choose the option
• Press / to adjust the option’s value
• Press conrm to adjust the window
automatically (The brighter the
edges are, the more accurate the
adjustment will be)
• Press “menu” to return to
previous menu
• Press “exit” to escape the menu
• Press / to choose sound mode
• Press / to choose the option
• Press / to adjust the option’s value
• Press enter to get into the submenu
• Press “menu” to return to previous menu
• Press “exit” to escape the menu
Sound
Screen Menu

15
Get into the sound mode submenu, the treble and base could be chosen after the
sound mode is changed to be “user”. Press / to switch options.
• Press / to choose the option
• Press / to adjust the option’s value
• Press “menu” to return to previous menu
• Press “exit” to escape the menu
Get into surround sound option; you could turn on/ o the surround. Press /
to switch options.
• Press / to choose the option
• Press / to adjust the option’s value
• Press “menu” to return to previous menu
• Press “exit” to escape the menu
Screen Menu

16
Get into EQ submenu, there are ve options: 20Hz, 500Hz, 1.5KHz, 5KHz, 10KHz.
Press / to switch options.
When in the time menu, the clock, o time, on time, sleep timer and OSD Duration
options will be displayed, press / to switch options.
• Press / to choose time menu
• Press / to choose the option
• Press enter to get into submenu
• Press / to adjust the option’s value
• Press “menu” to return to previous menu
• Press “exit” to escape the menu
Time
Balance
• Press / to choose the option
• Press / to adjust the option’s value
• Press “menu” to return to previous menu
• Press “exit” to escape the menu
Screen Menu

17
When in the clock submenu, there are ve options: date, month, year, hour, minute,
press / to switch options.
• Press / to choose the option
• Press / to adjust the option’s value
• Press “menu” to return to previous menu
• Press “exit” to escape the menu
Clock
Get into O Time submenu, hour and minute
options will be displayed, the O Time mode
could be set as once a day, Monday to Friday,
Monday to Sunday and Sunday. Press /
to switch options.
• Press / to choose the option
• Press / to adjust the option’s value
• Press “menu” to return to previous menu
• Press “exit” to escape the menu
O Time
Screen Menu

18
Get into On Time submenu, hour, minute, PC 1, volume options will be displayed.
The On Time mode could be set as once a day, Monday to Friday, Monday to Sunday
and Sunday. Press / to switch options.
• Press / to choose the option
• Press / to adjust the option’s value
• Press “menu” to return to previous menu
• Press “exit” to escape the menu
On Time
Get into sleep time submenu, there are nine
options: o, 10min, 20min, 30min, 60min, 90min,
120min, 180min, 240min. Press / to switch
options.
• Press / to choose the option
• Press / to adjust the option’s value
• Press “menu” to return to previous menu
• Press “exit” to escape the menu
Sleep Time
Screen Menu