Elo Touch Solutions 1517L User manual

USER MANUAL
Elo Touch Solutions
1517L and 1717L Touchmonitors
SW601708 Rev E

User Manual: 1517L, 1717L
SW601708 Rev E, Page 2 of 25
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or by any means,
including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise
without prior written permission of Elo Touch Solutions, Inc.
Disclaimer
The information in this document is subject to change without notice. Elo Touch Solutions, Inc.
and its Affiliates (collectively "Elo") makes no representations or warranties with respect to the
contents herein, and specifically disclaims any implied warranties of merchantability or fitness
for a particular purpose. Elo reserves the right to revise this publication and to make changes
from time to time in the content hereof without obligation of Elo to notify any person of such
revisions or changes.
Trademark Acknowledgments
AccuTouch, CarrollTouch, Elo, Elo (logo), Elo Touch, Elo Touch Solutions, Elo TouchSystems,
IntelliTouch, iTouch, SecureTouch, TouchTools and VuPoint are trademarks of Elo and its
Affiliates. Windows is a trademark of Microsoft Corporation.

User Manual: 1517L, 1717L
SW601708 Rev E, Page 3 of 25
Table of Contents
Chapter 1: Introduction ............................................................................4
Chapter 2: Installation ..............................................................................5
Chapter 3: Mounting.................................................................................7
Chapter 4: Operation..............................................................................12
Chapter 5: Technical Support ................................................................16
Chapter 6: Safety & Maintenance ..........................................................18
Chapter 7: Regulatory Information........................................................20

User Manual: 1517L, 1717L
SW601708 Rev E, Page 4 of 25
Chapter 1: Introduction
Product Description
Your new touchmonitor combines the reliable performance of Elo Touch Solutions touch
products with the latest developments in touch technology and display design. This combination
of features creates a natural flow of information between the user and the touchmonitor.
This touchmonitor incorporates a 16.2M color, active matrix thin-film-transistor LCD panel to
provide high quality display performance. Its LED backlight significantly reduces power
consumption and eliminates mercury (compared to CCFL-backlit panels). Other features that
enhance this LCD monitor’s performance are Plug & Play compatibility, on-screen display
(OSD) controls, and an optional magnetic stripe reader (MSR).
Precautions
Follow all warnings, precautions and maintenance as recommended in this user manual to
maximize the life of your unit, to ensure user safety, and to prevent risks. See the Safety &
Maintenance chapter for more information.
This manual contains information that is important for the proper setup and maintenance of the
unit. Before setting up and powering on your new touchmonitor, read through this manual,
especially the Installation, Mounting, and Operation chapters.

User Manual: 1517L, 1717L
SW601708 Rev E, Page 5 of 25
Chapter 2: Installation
Unpacking the Touchmonitor
Open the carton and verify that the following items are present:
•Touchmonitor with protective sheet over touchscreen
•User Manuals CD
•Japanese language regulatory information pamphlet
•Quick Install Guide
•VGA cable
•USB cable
•North American power cable
•European power cable

User Manual: 1517L, 1717L
SW601708 Rev E, Page 6 of 25
Connector Panel & Interfaces
Touchmonitor Connections
1. Connect the VGA video cables between the monitor’s VGA input connectors and your VGA
video source, respectively. Tighten the video cable’s screws for best performance.
2. Connect the USB/serial touch cable between the monitor’s USB/serial connector and your
PC’s USB/serial port.
3. Select the correct power cable for your region. Connect the power cable between the AC
power source and the monitor’sAC input power jack.
4. Alternatively, if you have purchased an optional power adapter and elected to use it, connect
the cable between the AC power source and the optional power adapter’s input connector.
Connect the power adapter’s DC output connector to the monitor’s DC input power jack.
5. The touchmonitor ships in an OFF state. Press the power button to turn it on.

User Manual: 1517L, 1717L
SW601708 Rev E, Page 7 of 25
Installing the Touch Technology Software Drivers
Some software installation is required for your touchmonitor to work with your computer. No
additional drivers are required for your projected-capacitive touchmonitor, it uses Windows HID
drivers.
To download latest touch drivers
1.
Visit elotouch website.
2.Select the operating system from “Operating System” dropdown menu.
3.Select the technology from “Technologies” dropdown menu.
4.Click on the driver version required for your touchmonitor.
5.Click “Accept” once you are directed to the “Driver License Agreement” page.
6.Enter you email address, Click on “Next Step”. Your driver download will start automatically.
7.If you are a new user, fill in the required information and Click on “Register”. Your driver
download will start automatically.

User Manual: 1517L, 1717L
SW601708 Rev E, Page 8 of 25
Chapter 3: Mounting
Rear VESA Mount
For the 15 inch touchmonitor, a four-hole 75x75mm mounting pattern for M4 screws is provided on
the rear of the monitor. Remove the stand using a Phillips screwdriver to access this mounting
interface. The VESA FDMI-compliant counting is coded: VESA MIS-B, 75, C.
An optional filler plate is available for purchase separately to use with the VESA mount:
E000404 (Black)
E000420 (White)

User Manual: 1517L, 1717L
SW601708 Rev E, Page 9 of 25
For the 17 inch touchmonitor, a four-hole 75x75mm mounting pattern for M4 screws is provided
on the rear of the monitor. Remove the stand using a Phillips screwdriver to access this
mounting interface. The VESA FDMI-compliant counting is coded: VESA MIS-B, 75, C.
An optional filler plate is available for purchase separately to use with the VESA mount:
E000405 (Black)
E000421 (White)

User Manual: 1517L, 1717L
SW601708 Rev E, Page 10 of 25
Base Mount
For the 15 inch touchmonitor, a threaded three-hole mounting pattern for M4 screws is provided
on the bottom of stand base for mounting or securing. An additional two-hole pattern is available
under small caps on the top of the base. See page 15 for instructions on how to access holes.
For the 17 inch touchmonitor, a threaded three-hole mounting pattern for M4 screws is provided
on the bottom of stand base for mounting or securing. An additional two-hole pattern is available
under small caps on the top of the base. See page 15 for instructions on how to access holes.

User Manual: 1517L, 1717L
SW601708 Rev E, Page 11 of 25
Both the 15” and 17” touchmonitors have covered mounting holes for securing the stand to a
flat surface using M4 flathead screws. To utilize these mounting holes, unsnap the access
covers from the outside, install the screws into the holes and then snap the cover back into
place.

User Manual: 1517L, 1717L
SW601708 Rev E, Page 12 of 25
Chapter 4: Operation
Power
To turn the touchmonitor on or off, press the touchmonitor power button once.
The Power Status LED on the bottom of the touchmonitor functions according to the following
table:
Touchmonitor
status
LED status
OFF OFF
SLEEP PULSING
ON ON
The system consumes low power when in SLEEP and OFF modes.
Touching the screen will bring the attached host PC out of SLEEP mode (similar to moving the
mouse or pressing a keyboard key).
To improve reliability and reduce wasteful power consumption, disconnect the power adapter
when long periods of disuse are planned.
Touch
Your touchmonitor is factory-calibrated and should not need manual calibration (unless the
input video is not fully scaled to the native resolution, or the touch experience needs to be
calibrated to a specific user).

User Manual: 1517L, 1717L
SW601708 Rev E, Page 13 of 25
Video
A display’s native resolution is its width and height measured in number of pixels. Generally, for
best performance, an image displayed on this monitor will look best when your computer’s
output resolution matches this monitor’s native resolution, which is 1024 x 768 for the 15 inch,
or 1280 x 1024 for the 17 inch.
For computer output resolutions at non-native resolutions, the monitor will scale the video to its
panel’s native resolution. This involves stretching or compressing the input image as needed in
the X- and Y-dimensions to fit the display’s native resolution. An unavoidable byproduct of the
scaling algorithms is a loss of fidelity when the computer’s output video image is scaled by the
monitor to fit the display. This loss of fidelity is most apparent when viewing feature-rich images
at close distances (for example images containing small-font text).
Your touchmonitor will likely not require video adjustments. However, for analog VGA video,
variations in video graphic card outputs may require user adjustments through the OSD to
optimize the quality of the touchmonitor’s displayed image. These adjustments are
“remembered” by the touchmonitor. Also, to reduce the need for adjustments for different video
mode timings, the monitor correctly scales and displays some of the video industry’s most
common video timing modes.
On-Screen Display (OSD)
Four OSD buttons are on the bottom of the monitor. These can be used to adjust various
display parameters.
The buttons and their functionality are:
Button Function when OSD is not displayed: Function when OSD is displayed:
Menu Display OSD main menu Return to previous OSD menu
Display OSD Brightness submenu Decrease value of selected parameter /
select previous menu item
Display OSD Contrast submenu Increase value of selected parameter /
select next menu item
Select Auto Adjust Select parameter for adjustment /
select submenu to enter

User Manual: 1517L, 1717L
SW601708 Rev E, Page 14 of 25
The OSD buttons control an on-screen graphical user interface, which displays on top of your
input video. This allows for intuitive adjustment of the following display parameters:
Parameter
Available Adjustment
Brightness Increase/decrease monitor brightness
Default: Maximum
Contrast Increase/decrease monitor contrast
Default: Best gray-shade performance
Clock Allows fine adjustments of the panel’s pixel dot clock
Only applicable for VGA input video
Phase Allows fine adjustments of the panel’s pixel dot clock phase
Only applicable for VGA input video
Auto Adjust Automatically adjusts the system clock to the input analog VGA video
signal, affecting the H-position, V-position, Clock, and Phase menu items
Only applicable for VGA input video
H-position Moves the image horizontally on the display in single-pixel increments
Default: Centered
Only applicable for VGA input video
V-position Moves the image vertically on the display in single-pixel increments
Default: Centered
Only applicable for VGA input video
Aspect Ratio
Switches the scaling method between Full Screen and MaintainAspect
Ratio
Default: Full Screen
Full Screen – scales the X- and Y-dimensions of the input video (up or
down as needed) to the display’s native resolution.
Fill To Aspect Ratio – Assuming a landscape orientation and an input
video
with aspect ratio smaller than 1024 x 768 for the 15-
inch or 1280 x 1024 for
the 17-inch, scales the Y-dimension of the input video (up or down as
needed) to the display’s Y-resolution, and scales the X-dimension to
maintain the input video’s aspect ratio (and fills the rest of the display with
equal black bars on the left and right).
The touchscreen may need recalibration when switching between Aspect
Ratio options.
Sharpness Adjusts sharpness of the displayed images
Default: No sharpness adjustment
Only applicable at non-native input video resolutions
Color
Temperature
Selects the display’s color temperature. The available color temperatures
are 9300K, 7500K, 6500K, 5500K, and User Defined. If the User Defined
option is selected, the user can change the color temperature by changing
individual R, G, and B gains on a scale from 0 to 100.
Default: User Defined with R, G, and B all set to 100

User Manual: 1517L, 1717L
SW601708 Rev E, Page 15 of 25
OSD Timeout
Adjusts how long a period of OSD button inactivity the touchmonitor will
wait before closing the OSD. The adjustable range is between 5 and 60
seconds.
Default: 15 seconds
OSD Language
Selects which language the OSD information is displayed in. The available
languages are: English, French, Italian, German, Spanish, Simplified
Chinese, Traditional Chinese, and Japanese
Default: English
Recall Defaults Selecting “Recall Defaults” restores all factory default settings for
OSD-adjustable parameters (except OSD Language) and for Preset Video
Mode timings.
Video Source
The monitor continually scans for active video on the VGA and DVI
connectors. This adjustment selects which of those input ports should be
given priority to be displayed.
The options are: VGA Priority, DVI Priority
Default: DVI Priority
All touchmonitor adjustments made through the OSD are automatically memorized as soon as
they are entered. This feature saves you from having to reset your choices every time the
touchmonitor is unplugged or powered off and on. If there is a power failure, the touchmonitor
settings will not default to the factory specifications.
OSD and Power Lockouts
Press and hold the “Menu” and “Down” buttons for two seconds to enable/disable the OSD
Locking feature. When the OSD Locking is enabled, pressing any of the Menu, Up, Down, or
Select keys will have no effect on the system.
Press and hold the “Menu” and “Up” buttons for two seconds to enable/disable the Power
Locking feature. When the Power Locking is enabled, pressing the power switch will have no
effect on the system.

User Manual: 1517L, 1717L
SW601708 Rev E, Page 16 of 25
Chapter 5: Technical Support
If you are experiencing trouble with your touchmonitor, refer to the following suggestions.
If the problem persists, please contact your local dealer or contact Elo Touch Solutions
Customer Service.
Solutions to Common Problems
Problem Suggested Troubleshooting
The touchmonitor does not respond when
turning on the system
Check that the DC power adaptor is properly
connected
Verify the DC power adaptor is functioning
Monitor display is dim Use the OSD to increase the brightness
Use the OSD to increase the contrast
Monitor display is blank
If the Power Status LED is blinking, the monitor may
be in SLEEP mode.
Press any key / move the mouse
/ touch the Touchscreen to see if the image
reappears
Check that the signal source device is turned on
Check that that there are no loose cable connections
Monitor displays an “Out Of Range”
message
Adjust your computer’s resolution/timing mode to be
within the allowable timing ranges specified for your
touchmonitor (see website for specifications)
Monitor display image looks abnormal
Adjust your computer’s resolution/timing mode to be
within the allowable timing ranges specified for your
touchmonitor (see website for specifications)
Use the Auto Adjust function in the OSD
Touch functionality doesn’t work Verify your PC has the latest Elo drivers installed Perform the calibration routine provided with the
latest Elo drivers
The OSD buttons or power button does not
respond when pressed Check to see if the OSD lock or power lock functions are on

User Manual: 1517L, 1717L
SW601708 Rev E, Page 18 of 25
Chapter 6: Safety & Maintenance
Safety
To avoid risk of electric shock, follow all safety notices and do not disassemble the
touchmonitor. They are not user-serviceable.
Ensure that your installation is equipped to maintain the specified environmental conditions
listed in the Technical Specifications chapter.
Care and Handling
The following tips will help keep your touchmonitor functioning at an optimal level:
•Disconnect the AC power cable before cleaning.
•To clean the display unit cabinet, use a clean cloth lightly dampened with a mild detergent.
•It is important that your unit remains dry. Do not get liquids on or inside the unit. If liquid
does get inside, have a qualified service technician check it before you power it on again.
•Do not wipe the screen with a cloth or sponge that could scratch the surface.
•To clean the touchscreen, use window or glass cleaner applied to a clean cloth or sponge.
Never apply the cleaner directly to the touchscreen. Do not use alcohol (methyl, ethyl or
isopropyl), thinner, benzene, or other abrasive cleaners.

User Manual: 1517L, 1717L
SW601708 Rev E, Page 19 of 25
Waste Electrical & Electronic Equipment Directive (WEEE)
This product should not be disposed of with household waste. It should be
deposited at a facility that enables recovery and recycling. Ensure that product is
disposed at the end of its useful life according to local laws and regulation.
Elo has put in place recycling arrangements in certain parts of the world.

User Manual: 1517L, 1717L
SW601708 Rev E, Page 20 of 25
Chapter 7: Regulatory Information
I. Electrical Safety Information:
Compliance is required with respect to the voltage, frequency, and current requirements
indicated on the manufacturer’s label. Connection to a different power source than those
specified herein will likely result in improper operation, damage to the equipment or pose a fire
hazard if the limitations are not followed.
There are no operator serviceable parts inside this equipment. There are hazardous voltages
generated by this equipment which constitute a safety hazard. Service should be provided only
by a qualified service technician.
Contact a qualified electrician or the manufacturer if there are questions about the installation
prior to connecting the equipment to mains power.
II. Emissions and Immunity Information
Notice to Users in the United States: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
Notice to Users in Canada: This equipment complies with the Class B limits for radio noise
emissions from digital apparatus as established by the Radio Interference Regulations of
Industrial Canada.
Notice to Users in the European Union: Use only the provided power cords and
interconnecting cabling provided with the equipment. Substitution of provided cords and cabling
may compromise electrical safety or CE Mark Certification for emissions or immunity as
required by the following standards:
This Information Technology Equipment (ITE) is required to have a CE Mark on the
Manufacturer’s label which means that the equipment has been tested to the following
Directives and Standards: This equipment has been tested to the requirements for the CE Mark

User Manual: 1517L, 1717L
SW601708 Rev E, Page 21 of 25
as required by EMC Directive 2004/108/EC as indicated in European Standard EN 55022 Class
B and the Low Voltage Directive 2006/95/EC as indicated in European Standard EN 60950.
General Information to all Users: This equipment generates, uses and can radiate radio
frequency energy. If not installed and used according to this manual the equipment may cause
interference with radio and television communications. There is, however, no guarantee that
interference will not occur in any particular installation due to site-specific factors.
1) In order to meet emission and immunity requirements, the user must observe the following:
a) Use only the provided I/O cables to connect this digital device with any computer.
b) To ensure compliance, use only the provided manufacturer’s approved line cord.
c) The user is cautioned that changes or modifications to the equipment not expressly
approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
2) If this equipment appears to cause interference with radio or television reception, or any
other device:
a) Verify as an emission source by turning the equipment off and on.
If you determine that this equipment is causing the interference, try to correct the interference
by using one or more of the following measures:
i) Move the digital device away from the affected receiver.
ii) Reposition (turn) the digital device with respect to the affected receiver.
iii) Reorient the affected receiver’s antenna.
iv) Plug the digital device into a differentAC outlet so the digital device and the receiver are
on different branch circuits.
v) Disconnect and remove any I/O cables that the digital device does not use.(Unterminated
I/O cables are a potential source of high RF emission levels.)
vi) Plug the digital device into only a grounded outlet receptacle. Do not use AC adapter
plugs. (Removing or cutting the line cord ground may in crease RF emission levels and may
also present a lethal shock hazard to the user.)
If you need additional help, consult your dealer, manufacturer, or an experienced radio or
television technician.