Winmate W10IB3S-PCH2LB User manual

Please read these instructions carefully before using this product, and save this manual for future use.
7”/ 10.4”/ 15”
S Series HMI
Intel® Celeron® Bay Trail-M N2930, 1.83 GHz
Model No. W07IB3S-PCO1-POE
W07IB3S-PCO1AC-POE
W10IB3S-PCH2-POE
W10IB3S-PCH2AC-POE
W10IB3S-PCH2LB
R15IB3S-PCC3-POE
Quick Start Guide
Document Version 1.3
Document Part No. 9152111I1140

2
7~15" S Series HMI Quick Start Guide
Contents
Preface.....................................................................................................................................3
Chapter 1: Introduction ..........................................................................................................7
1.1 Introduction .......................................................................................................... 8
1.2 Product Features.................................................................................................. 8
1.3 Package Contents................................................................................................ 9
1.4 Mechanical Dimensions ..................................................................................... 10
1.5 Physical Buttons and LED Indicators ................................................................. 13
1.6 Connector Description........................................................................................ 14
Chapter 2: Getting Started ................................................................................................... 15
2.1 Powering On ...................................................................................................... 16
2.2 Connector Description........................................................................................ 16
2.3 Turning On and Off the Device........................................................................... 18
Chapter 3: Mounting............................................................................................................. 19
3.1 Panel Mount....................................................................................................... 20
3.2 VESA Mount....................................................................................................... 21
3.3 Front Side Wall Mount........................................................................................ 25
3.4 Glass Wall Mount............................................................................................... 26
Chapter 4: Operating the Device ......................................................................................... 27
4.1 Hot Tab Menu .................................................................................................... 28
4.2 Using HF RFID Reader...................................................................................... 30
4.3 Using Front Camera........................................................................................... 33
4.4 How to Enable Watchdog................................................................................... 37
Appendix................................................................................................................................ 38
Appendix A: Product Specifications.......................................................................... 38
Appendix B: HF RFID Reader Specifications........................................................... 39

3
Preface
Preface
Copyright Notice
No part of this document may be reproduced, copied, translated, or transmitted in any form or
by any means, electronic or mechanical, for any purpose, without the prior written permission
of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective owners.
Disclaimer
We reserve the right to make changes, without notice, to any product, including circuits and/or
software described or contained in this manual in order to improve design and/or performance.
We assume no responsibility or liability for the use of the described product(s) conveys no
license or title under any patent, copyright, or masks work rights to these products, and make
no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described in this
manual are for illustration purposes only. We make no representation or guarantee that such
application will be suitable for the specified use without further testing or modification.
Warranty
Our warranty guarantees that each of its products will be free from material and workmanship
defects for a period of one year from the invoice date. If the customer discovers a defect, we
will, at his/her option, repair or replace the defective product at no charge to the customer,
provide it is returned during the warranty period of one year, with transportation charges
prepaid. The returned product must be properly packaged in its original packaging to obtain
warranty service. If the serial number and the product shipping data differ by over 30 days, the
in-warranty service will be made according to the shipping date. In the serial numbers the third
and fourth two digits give the year of manufacture, and the fifth digit means the month (e. g.,
with A for October, B for November and C for December).
For example, the serial number 1W18Axxxxxxxx means October of year 2018.
Customer Service
We provide a service guide for any problem by the following steps: First, visit the website of
our distributor to find the update information about the product. Second, contact with your
distributor, sales representative, or our customer service center for technical support if you
need additional assistance.
You may need the following information ready before you call:
Product serial number
Software (OS, version, application software, etc.)
Description of complete problem
The exact wording of any error messages
In addition, free technical support is available from our engineers every business day. We are
always ready to give advice on application requirements or specific information on the
installation and operation of any of our products.

4
7~15" S Series HMI Quick Start Guide
Advisory Conventions
Four types of advisories are used throughout the user manual to provide helpful information or to
alert you to the potential for hardware damage or personal injury. These are Notes, Important,
Cautions, and Warnings. The following is an example of each type of advisory.
Note:
A note is used to emphasize helpful information
Important:
An important note indicates information that is important for you to know.
Caution A Caution alert indicates potential damage to hardware and explains how
to avoid the potential problem.
Attention Une alerte d’attention indique un dommage possible à l’équipement et
explique comment éviter le problème potentiel.
Warning! An Electrical Shock Warning indicates the potential harm from electrical
hazards and how to avoid the potential problem.
Avertissement! Un Avertissement de Choc Électrique indique le potentiel de
chocs sur des emplacements électriques et comment éviter ces problèmes.
Safety Information
Warning! Always completely disconnect the power cord from your chassis
whenever you work with the hardware. Do not make connections while the power is
on. Sensitive electronic components can be damaged by sudden power surges.
Only experienced electronics personnel should open the PC chassis.
Avertissement! Toujours débrancher le cordon d’alimentation du chassis
lorsque vous travaillez sur celui-ci. Ne pas brancher de connections lorsque
l’alimentation est présente. Des composantes électroniques sensibles peuvent être
endommagées par des sauts d’alimentation. Seulement du personnel expérimenté
devrait ouvrir ces chassis.
Caution Always ground yourself to remove any static charge before touching the
CPU card. Modern electronic devices are very sensitive to static electric charges.
As a safety precaution, use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded bag when they are not
in the chassis.
Attention Toujours verifier votre mise à la terre afin d’éliminer toute charge
statique avant de toucher la carte CPU. Les équipements électroniques moderns
sont très sensibles aux décharges d’électricité statique. Toujours utiliser un
bracelet de mise à la terre comme précaution. Placer toutes les composantes
électroniques sur une surface conçue pour dissiper les charge, ou dans un sac
anti-statique lorsqu’elles ne sont pas dans le chassis.
For your safety carefully read all the safety instructions before using the device. Keep this user
manual for future reference.
Always disconnect this equipment from any AC outlet before cleaning. Do not use liquid or
spray detergents for cleaning. Use a damp cloth.
For pluggable equipment, the power outlet must be installed near the equipment and must
be easily accessible.
Alternating Current The Protective Conductor Terminal (Earth Ground)
symbol indicates the potential risk of serious electrical shock due to improper
grounding.
Mise à le terre !Le symbole de Mise à Terre indique le risqué potential de choc
électrique grave à la terre incorrecte.

5
Preface
Keep this equipment away from humidity.
Put this equipment on a reliable surface during installation. Dropping it or letting it fall
could cause damage.
The openings on the enclosure are for air convection and to protect the equipment from
overheating.
Do not cover the openings.
Before connecting the equipment to the power outlet make sure the voltage of the power
source is correct.
Position the power cord so that people cannot step on it. Do not place anything over the
power cord.
If the equipment is not used for a long time, disconnect it from the power source to avoid
damage by transient over-voltage.
Never pour any liquid into an opening. This could cause fire or electrical shock.
Never open the equipment. For safety reasons, only qualified service personnel should
open the equipment.
All cautions and warnings on the equipment should be noted.
Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -20°C (-4°F) or above 60°C (140°F). It may damage the
equipment.
Caution Use the recommended mounting apparatus to avoid risk of injury.
Attention Utiliser l’appareil de fixation recommandé pour éliminer le risque
de blessure.
Warning! Only use the connection cords that come with the product. When in
doubt, please contact the manufacturer.
Avertissement!Utiliser seulement les cordons d’alimentation fournis avec
le produit. Si vous doutez de leur provenance, contactez le manufacturier.
Warning! Always ground yourself against electrostatic damage to the device.
Avertissement! Toujours vérifier votre mise à la terre afin que
l’équipement ne se décharge pas sur vous.
Cover workstations with approved anti-static material. Use a wrist strap connected to a
work surface and properly grounded tools and equipment.
Use anti-static mats, heel straps, or air ionizer for added protection.
Avoid contact with pins, leads, or circuitry.
Turn off power and input signals before connecting test equipment.
Keep the work area free of non-conductive materials, such as ordinary plastic assembly
aids and Styrofoam.
Use filed service tools, such as cutters, screwdrivers that are conductive.
Always put drivers and PCB’s component side on anti-static foam.
General Guideline
It is recommended to reboot the device when some functions are defect or inactive. If it
still can't solve the problems please contact your dealer or agent.
Replaceable Batteries
If am equipment is provided with a replaceable battery and if replacement by an incorrect type
could result in an explosion (For example with some lithium batteries), the following applies:
The battery is placed in an OPERATOR ACCESS AREA, there shall be a marking close to
the battery or a statement in both the operating and the servicing instructions;
If the battery is placed elsewhere in equipment, there shall be a marking close to the battery

6
7~15" S Series HMI Quick Start Guide
or a statement in the servicing instructions.
These marking or statement shall include the following or similar text:
Caution Risk of explosion if battery is replaced by an incorrect type. Dispose of
used batteries according to the instructions.
Attention Risque d'explosion si la batterie est remplacée par un type incorrect.
Jetez les piles usagées conformément aux instructions.
Important Information
Federal Communications Commission Radio Frequency Interface Statement
This device complies with part 15 FCC rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class "B" digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at him own expense.
EC Declaration of Conformity
This equipment is in conformity with the requirement of the
following EU legislations and harmonized standards. Product also
complies with the Council directions.
Electromagnetic Compatibility Directive (2014/30/EU)
EN55024: 2010 EN 55022: 2010 Class B
oIEC61000-4-2: 2009
oIEC61000-4-3: 2006+A1: 2007+A2: 2010
oIEC61000-4-4: 2012
oIEC61000-4-5: 2014
oIEC61000-4-6: 2013
oIEC61000-4-8: 2010
oIEC61000-4-11: 2004
EN55022: 2010/AC:2011
EN61000-3-2:2014
EN61000-3-3:2013
Low Voltage Directive (2014/35/EU)
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/ A2:2013

7
Chapter 1: Introduction
Chapter 1: Introduction
This chapter gives you product overview, describes features and hardware
specification. You will find all accessories that come with the HMI in the
packing list. Mechanical dimensions and drawings included in this chapter.

8
7~15" S Series HMI Quick Start Guide
1.1 Introduction
Congratulations on purchasing Winmate® S Series HMI. Winmate multi-touch S Series HMI is
suitable for home automation and room management systems. Flat surface is easy-to-clean
and delivers aesthetically pleasing look for any interior. The device provides real time update
for booking status and available schedule, or performs as a synchronous display in meetings.
S Series HMI run on Intel® Celeron® N2930 processor and support Windows 10 IoT,
Windows Embedded 8.1 Industry Pro, Windows Embedded 8Standard, Windows 7 Pro for
Embedded Systems, and Windows Embedded Standard 7–WS7P. For easy, quick and cost
effective network installations both models support PoE. These models sealed with front IP 65
dust and water proof, and IP22 on the back side. Optional HF RFID 13.56 MHz is especially
useful in access control applications.
S Series HMI support an exceptional feature - LED light bar. With the help of red, green, blue
and orange LED indicators you can see the status of the machine or processes afar. It
significantly reduces power consumption by keeping the display turned off.
The S Series HMI is suitable for home automation and room management systems. Flat
surface is easy-to-clean and delivers aesthetically pleasing look for any interior. By connecting
to centralized database, it can provide real time update for booking status and available
schedule, or perform as a synchronous display in meetings. Optional RFID reader is
especially useful in access control applications.
1.2 Product Features
Winmate® S Series HMI features:
7/ 10.1/ 15-inch TFT LCD
Projected capacitive multitouch screen
Intel® Celeron® Bay Trail-M N2930, 1.83 GHz
1 x USB 3.0, 1 x USB 2.0, 1 x RS-232/422/485
1 x RJ45 - 10/100/1000 Mbps (LAN), 1 x RJ45 - 10/100/1000 Mbps (LAN/ PoE)
PoE IEEE 802.3at (25 W), IEEE 802.3af (15 W)
Fanless cooling system and ultra-low power consumption
Front IP65 water and dust proof, rear IP22
Light design for machine automation, smart factory and IoT applications

9
Chapter 1: Introduction
1.3 Package Contents
Carefully remove the box and unpack your HMI device. Please check if all the items listed below
are inside your package. If any of these items are missing or damaged contact us immediately.
Standard factory shipment list:
HMI Device
Quick Start Guide
(Hardcopy)
Driver CD & User
Manual
AC Adapter (12V/
50W)
Varies by product
specifications
Part No. 9152111I1140
Part No. 9171111I101Y
Part No. 922D050W12VA
Power Cord
3 pin Terminal
Block to DC Jack
VESA Screws
Varies by country
Part No. 94J602G030K0
Part No. 82111E240400
Package may include optional accessories based on your order:
VESA Desk Stand
PCVS-V1
VESA Desk Stand
LA-100
VESA Wall Mount
Bracket LA-106
Front Side Wall
Mount PCFW-V1
Part No. 99KK00A0000E
Part No. 9B0000000128
Part No. 9B0000000412
Part No. 99KK00A0000C
Glass Wall Mount
Kit
Right: PCGM-V2R
Left: PCGM-V2L
External USB
Cable
Part No. 99KN00A00010
(Right)
Part No. 99KN00A00011
(Left)
Part No. 948018102100

10
7~15" S Series HMI Quick Start Guide
1.4 Mechanical Dimensions
This section describes appearance, connectors’ layout and mechanical dimensions of S Series
HMI. Notice that this is a simplified drawing and some components are not marked in detail.
Please contact our sales representative if you need further product information.
7-inch, W07IB3S-PCO1-POE/ W07IB3S-PCO1AC-POE
Unit: mm
Dimensions:189.4 x 145.4 x 36.1
No.
Description
No.
Description
①
RJ-45 (LAN)
⑥
1 Watt Speaker
②
USB 3.0, USB 2.0
⑦
2MP Front Camera (Optional)
③
RS-232
⑧
RGB LED Light Bar
(W07IB3S-PCM1AC only)
④
3 Pin Terminal Block 12V DC
⑨
HF RFID Reader (Optional)
⑤
RJ-45 (LAN/ PoE)

11
Chapter 1: Introduction
10.1-inch, W10IB3S-PCH2-POE/ W10IB3S-PCH2AC-POE Unit: mm
Dimensions:263.48 x 172 x 35.7
Note 1 : Digital I/O is an optional connector and may not be present in your model.
Note 2 :Power Device (PD): IEEE 802.3at (25 W)
№
Description
№
Description
①
GPIO (Optional)*
⑥
RJ-45 (LAN/ PoE)**
②
RJ-45 (LAN)
⑦
2MP Front Camera (Optional)
③
USB 2.0, USB 3.0
⑧
HF RFID Reader (Optional)
④
RS-232/422/485
⑨
LED Status Light Bar
(W10IB3S-PCH2AC-PoE only)
⑤
3 Pin Terminal Block12V DC
(Phoenix Type)
⑩
1 Watt Speaker

12
7~15" S Series HMI Quick Start Guide
10.1-inch, W10IB3S-PCH2LB
Unit: mm
Dimensions:263.48 x 172 x 35.7
Note 1 :Power Device (PD): IEEE 802.3at (25 W)
№
Description
№
Description
①
RJ-45 (LAN)
⑤
RJ-45 (LAN/ PoE)**
②
USB 2.0, USB 3.0
⑥
All-Around LED Status Light Bar
③
RS-232/422/485
⑦
HF RFID Reader (Optional)
④
3 Pin Terminal Block12V DC
(Phoenix Type)
⑧
1 Watt Speaker

13
Chapter 1: Introduction
15-inch, R15IB3S-PCC3-POE
Unit: mm
Dimensions:363.4 x 277 x 86 x 44.5
№
Description
№
Description
①
RJ-45 (LAN)
⑥
Digital I/O (Optional)
②
USB 3.0 x 1 , USB 2.0 x 1
⑦
HF RFID Reader (Optional)
③
RS232/422/485
⑧
LED Status Light Bar (Optional)
④
12V DC Terminal Block 12V DC
⑨
1 Watt Speaker x 2
⑤
RJ-45 (LAN/ PoE)
1.5 Physical Buttons and LED Indicators
Physical buttons and LED indicators located on the rear side of the HMI (Only for 15”).

14
7~15" S Series HMI Quick Start Guide
Physical Buttons
Icon
Button
Description
Reset
Press to reset the system
Power On/ Off
Press to power on or power off the
device
LED Indicators
LED Type
Status
Description
On
Power is on
Off
Power is off
Blinking
Storage activity
(Data is being read or written)
Off
System is idle
1.6 Connector Description
Terminal interfaces are located on the bottom side of the HMI device.
Note:
Notice that input and output connectors vary by product size and
specifications.
Terminal interfaces description:
Item
Description
RJ45 –Connects HMI device to Ethernet network. Supports PoE for
power transmission in network equipment, via network UTP cable,
together with data.
Terminal Block 3 Pin –Provides power to the HMI device, accepts
12V DC.
Example: AC cord or DC power supply. If both are provided, choose
only one.
RS-232/422/485 –Connects external devices to HMI device.
Example: A barcode reader or scanner to HMI device.
USB 3.0, USB 2.0- Connects USB 3.0/ USB 2.0 compatible devices to
HMI device.
Example: A printer to HMI device.
GPIO - Connects the HMI device to specific GPIO pins to control it with
a software program.
Example: A door key lock system to HMI device.

15
Chapter 2: Getting Started
Chapter 2: Getting Started
This chapter tells you important information on power supply, adapter
and precautions tips. Pay attention to power considerations.

16
7~15" S Series HMI Quick Start Guide
2.1 Powering On
Installation Instruction:
1. Connect a 3-pin terminal block to the HMI connector.
2. Connect the other side of the terminal block to the AC adapter.
3. Connect the AC adapter to the power cord.
4. Plug in the power cord to a working AC wall outlet. The device will boot automatically.
2.2 Connector Description
2.2.1 Power Input Connector
The DC power source input of the panel PC is a 3 pin terminal block connector that supports
12V DC power input.
Pin assignment and connector description of terminal block connector.
Note:
Based on the model, terminal block connector may be located either on the bottom
or on the rear side of the HMI device.
Note:
Power cords vary in appearance by region and country.
Voltage
Minimum Voltage 11.4V
Maximum Voltage 12.6V
Maximum Current 4.2A

17
Chapter 2: Getting Started
2.2.2 Ethernet Connector
The HMI device has one RJ45 10/100/1000 Mbps Ethernet interface (LAN)for connecting to the
internet and one RJ45 10/100/1000 Mbps Ethernet interface (LAN or PoE based on your order).
Pin assignment and connector description of RJ45 connector.
Important:
PoE Rating 48V 0,6A
Power Device (PD): IEEE 802.3at (25 Watt)
2.2.3 Serial Port Connector
The S Series HMI has one serial port connector to connect your HMI to external devices such as
mouse, modem or printer. You can configure serial port settings via jumpers located on the
motherboard.
Pin assignment and connector description of serial port connector.
*Default setting: RS-232
2.2.4 USB Connector
The HMI device has one USB 2.0 and
one USB 3.0 connectors. Use USB 2.0 and USB 3.0 connector to connect your HMI device to
other USB 2.0/ USB 3.0 compatible devices.
Pin assignment and connector description of USB connector.
Pin №
Signal Name
Pin №
Signal Name
1
TX1+
2
TX1-
3
TX2+
4
TX2-
5
TX3+
6
TX3-
7
TX4+
8
TX4-
Pin №
*RS-232
RS-422
RS-485
1
DCD
TxD-
D-
2
RXD
TxD+
D+
3
TXD
RxD+
NC
4
DTR
RxD-
NC
5
GND
GND
GND
6
DSR
NC
NC
7
RTS
NC
NC
8
CTS
NC
NC
9
RI
NC
NC
Pin №
Signal Name
Pin №
Signal Name
1
+5V
2
USB_D-
3
USB_D+
4
GND
5
STDA_SSRX-
6
STDA_SSRX+
7
GND_DRAIN
8
STDA_SSTX-
9
STDA_SSTX+
10
+5V
11
USB_D-
12
USB_D+
13
GND

18
7~15" S Series HMI Quick Start Guide
2.2.5 GPIO Connector
Notice that GPIO is an optional connector and may not be present in your model.
2.3 Turning On and Off the Device
The unit is configured to Power ON when is connected to the power source.
You can Turn OFF the HMI device with the Windows power settings.
To shut down the device:
1. Tap Start >Shut down.
2. Wait for your HMI device to completely turn off before disconnecting the power cord (if
necessary).
Pin №
Signal Name
Pin №
Signal Name
1
GND
2
DI0
3
DI1
4
DI2
5
DI3
6
DO0
7
DO1
8
DO2
9
DO3
10
VCC

19
Chapter 3: Mounting
Chapter 3: Mounting
This chapter provides mounting guide for all available mounting
options. Pay attention to cautions and warning to avoid any
damages.

20
7~15" S Series HMI Quick Start Guide
3.1 Panel Mount
Panel mount mounting solutions is suitable for many applications where HMI should be
embedded in the machine. With this mounting solution flat surface leave no bezel in the front.
Size
Wall Cutout
Screw
7”
249 x 157.6 mm
M3 x 4mm
10.1”
249 x 157.6 mm
M3x4 mm
15”
345.4 x 260 mm
M6x4 mm
Installation Instruction
1. Prepare a fixture for the specific dimensions of the device.
2. Cut a hole on a sub frame or panel according to the cutout dimensions.
3. Install the device properly onto the cutout area of the sub frame or panel with the sides of
the front bezel.
4. Fix the device to fixture with eight screws.
Note:
Make sure that the eight holes on gasket can fit in the mounting holes on the
device.