Genelec 8010A User manual

English 1
8010A
Active Monitoring System
General description
The bi-amplied Genelec 8010A is an extremely
compact two-way active monitoring loudspeaker
designed for professional applications. It con-
tains drivers, power ampliers, active crossover
lters and protection circuitry. The MDE™ (Mini-
mum Diffraction Enclosure™) enclosure is made
of die-cast aluminium and shaped to reduce edge
diffraction. Combined with the advanced Direc-
tivity Control WaveguideTM (DCWTM), this design
provides excellent frequency balance in difcult
acoustic environments. If necessary, the bass re-
sponse of 8010A can be extended with a Genelec
subwoofer.
Packing contents
Each 8010A is supplied with a mains cable and
this operating manual.
Mounting considerations
Align the monitors correctly
Always place monitors so that their acoustic
axes converge at ear height at the listening posi-
tion (see Figures 1 and 2). Vertical orientation of
monitors is preferred, as it minimises acoustical
cancellation problems around the crossover fre-
quency.
Maintain symmetry
Check that the monitors are placed symmetrically
and at equal distance from the listening position.
If possible, place the monitors so that the listen-
ing position is on the centerline of the room and
the monitors are at an equal distance from the
room centerline.
Minimise reections
Acoustic reections from objects close to the
monitors, like desks, cabinets, computer moni-
tors etc. can cause unwanted colouration and
blurring of the sound image. These reections
can be minimised by placing the monitor away
from such surfaces.
Minimum clearances
If the monitor is installed in a restricted space
such as a cabinet or integrated into a wall struc-
ture, sufcient cooling for the amplier and func-
tioning of the reex port must be ensured.
A minimum clearance of 2.5 centimeters (1 in)
behind, above and on sides of the monitor must
be found. The space adjacent to the amplier
must either be ventilated or sufciently large to
dissipate heat so that the ambient temperature
does not rise above 35 degrees Celsius (95°F)
Connections
Connect the mains cables only after you have
completed connecting audio signal cabling.
The 8010A has a balanced XLR 7 kOhm audio
input connector. It can also be connected to an
unbalanced RCA line level audio source with a
suitable adapter cable your Genelec dealer can
provide. As the 8010A contains ampliers, no
power amplier is needed. Never connect 8010A
to the loudspeaker outputs of a power amplier,
integrated amplier, or receiver.
Operating Manual

2 English
Figure 1. Location of the acoustic axis
Figure 3. Control and connector layout on the rear panel of a 8010A.
Figure 2. Correct alignment of the monitors in a
5-channel system.
TO WATER OR MOISTURE. NO USER SERVICEABLE PARTS
ELECTRIC SHOCK HAZARD. DO NOT OPEN. DO NOT SUBJECT
L'INTÉRIEUR REMPLAÇABLE PARL'UTILISATEUR. ADRESSER
RISQUE DE CHOC ÉLECTRIQUE.NEPASOUVRIR. NE PA S
EXPOSER ÀL'EAU OU L'HUMIDITÉ. AUCUN COMPOSANTÀ
AVERTISSEMENT
WARNING
INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
TOUTE RÉPARATION ÀUN PERSONNEL QUALIFIÉ.
292-6010W
BASS TILT -4 dB
BASS TILT -2 dB
ISSDISABLE
SENSITIVITY -10dB
DESKTOP CONTROL
292-8010S
ON
8010A BI-AMPLIFIED
MONITORING SYSTEM
MAINS INPUT
50 /60Hz30W
100 - 240 V~
MADE IN FINLAND www.genelec.com
292-8010T
+-GND
2
3
IN 1
ISS DISABLE,
SENSITIVITY -10
dB,
BASS TILT
AND DESKTOP
CONTROLS
XLR SIGNAL
INPUT CONNECT
OR
MAINS
CONNECTOR
MAINS
SWITCH

English 3
Table 1: Suggested tone control settings for various acoustical environments
When all audio connections are completed,
connect the monitors to mains with the supplied
mains cables. They will switch on automatically.
ISSTM Autostart function
The signal sensing Autostart function of the
8010A powers it up when playback begins. Au-
tomatic powering down to standby mode hap-
pens after the playback has ended. The power
consumption in standby mode is less than 0.5
watts. The monitor will automatically and rapidly
start up once an input signal is detected.
There is a slight delay in the automatic
powering up. If this is undesirable, the ISSTM
function can be disabled by setting the “ISS
DISABLE” switch on the back panel to “ON”
position. In this mode, the monitor is powered
on and off using the power switch on the back
panel.
Sensitivity adjustment
The input sensitivity (playback level) of the
8010A has two alternative settings, normal and
-10 dB. The normal setting is factory default
and the lower, -10 dB setting can be selected by
turning the “SENSITIVITY -10 dB” switch on the
back panel to “ON”. The output levels are 100 dB
@ -6dBu and 90 dB @ -6 dBu respectively. Choose
the setting that gives the desired playback level
and good resolution of the volume control.
Tone controls
The frequency response of the Genelec 8010A
can be adjusted to match the acoustic envi-
ronment by setting the tone control switches
on the rear panel. The controls are “Bass Tilt”
and “Desktop”. Table 1 shows some examples
of typical settings in various situations. Figure 4
shows the effect of the controls on the anechoic
response.
Start adjustment by setting all switches to
“OFF” position. Measure or listen systematically
through the different combinations of settings to
nd the best frequency balance.
Bass Tilt
The Bass Tilt control offers three attenuation lev-
els for the bass response of the monitor, usually
necessary when the monitors are placed near a
wall or other room boundaries. The attenuation
levels are -2 dB (switch 1 “ON”), -4 dB (switch 2
“ON”) and -6 dB (both switches “ON”).
Monitor Mounting Environment Desktop Bass Tilt
Flat anechoic response OFF OFF
Free standing in a damped room OFF OFF
Free standing in a reverberant room OFF -2 dB
Near to a wall OFF -4 dB
Near eld on a reective surface ON (-4 dB @ 200 Hz) -2 dB
In a corner or a cabinet OFF -6 dB

4 English
Desktop Control
The “Desktop” low frequency control (switch
3) attenuates the bass frequencies by 4 dB at
200 Hz. This feature is designed to compensate
for the boost often occurring when the monitor is
placed on a table or similar horizontal surface.
Mounting options
The 8010A offers several mounting options:
Iso-Pod™ (Isolation Positioner/Decoupler™) vi-
bration insulating table stand allows tilting the
monitor towards the listener. On the rear, there
are three pairs of threaded holes compatible
with Omnimount®, VESA, and Sanus brackets.
For a full list of available options, please consult
Genelec’s accessories catalogue at www.genel-
ec.com or contact your Genelec dealer.
Maintenance
No user serviceable parts are to be found inside
the unit. Any maintenance or repair of the 8010A
should only be done by qualied service person-
nel.
Safety considerations
Although the 8010A has been designed in accord-
ance with international safety standards, the fol-
lowing warnings should be observed to ensure
safe operation and to maintain the monitor in safe
operating conditions:
• Servicing and adjustment must only be
performed by qualified service personnel. The
monitor must not be opened.
• Do not expose the monitor to water or
moisture. Do not place any objects filled with
liquid, such as vases, on the monitor or
near it.
• This monitor is capable of producing sound
pressure levels in excess of 85 dB, which may
cause permanent hearing damage.
• Free flow of air behind the monitor is
necessary to maintain sufficient cooling. Do not
obstruct airflow around the monitor.
• The amplifier is not completely
disconnected from the AC mains service unless
the mains power cord is removed from the
amplifier or the mains outlet.
Guarantee
This product is guaranteed for a period of two
years against faults in materials or workman-
ship. Refer to supplier for full sales and guarantee
terms.
Compliance to FCC rules
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
This device may not cause harmful interference, and
this device must accept
any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful interference in a residen-
tial installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guar-
antee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
Modications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment under FCC rules.

English 5
70
75
80
85
d
B
r
A
40 20k
70 100 200 500 1k 2k 5k 10k Hz
Genelec Oy 8010 (dBr) vs freq (Hz) 10 Jan 13
65
70
75
80
65
BASS TILT
DESKTOP
Figure 4. The curves
show the effect of the
“Bass Tilt” and “Desk-
top” controls on the
free field response of
the 8010A
70
75
80
85
d
B
r
A
40 20k
70 100 200 500 1k 2k 5k 10k Hz
Genelec Oy 8010 (dBr) vs freq (Hz) 10 Jan 13
65
15°
45°
0°
30°
60°
Figure 5. The upper
curve group shows the
horizontal directivity
characteristics of the
8010A measured at
1 m. The lower curve
shows the system's
power response.

6 English
SYSTEM SPECIFICATIONS
Lower cut-off frequency, –6 dB: < 67 Hz
Upper cut-off frequency, –6 dB: >25 kHz
Free eld frequency response (± 2.5
dB):
74 Hz–20 kHz
Max. short term sine wave acoustic
output on axis in half space, averaged
from
100 Hz to 3 kHz
at 1 m distance
at 0.5 distance
>96 dB SPL
>102 dB SPL
Maximum long term RMS acoustic
output in same conditions with IEC
weighted noise (limited by driver unit
protection circuit) @ 1 m:
>91 dB SPL
Maximum peak acoustic output per pair
on top of console, @ 1 m distance with
music material:
>105 dB
Self generated noise level in free eld @
1 m on axis (A-weighted):
<5 dB
Harmonic distortion at 80 dB SPL @
1 m on axis
Freq: 70…400 Hz
>400 Hz
< 3 %
< 0.5 %
Drivers:
Bass
Treble
76 mm (3 in)
cone
19 mm (3/4 in)
metal dome
Weight: 1.5 kg (3.3 lb)
Dimensions:
Height including Iso-Pod™ table
stand
Height without Iso-Pod™ table
stand
Width
Depth
195 mm (711/16 in)
181 mm (71/8 in)
121 mm (43/4 in)
115 mm (41/4 in)
CROSSOVER SECTION
Input connector: XLR female 7 kOhm: pin 1 gnd,
pin 2 +
pin 3 -
Input level for 100 dB SPL output at 1 m: -6 dBu
(Sensitivity
-10 dB off)
Level control range relative to max output: -10 dB
(Sensitivity
-10 dB on)
Desktop control operating range: 0 to –4 dB @
200 Hz
Crossover frequency, Bass/Treble: 3.0 kHz
Bass Tilt control operating range in –2
dB steps:
0 to –6 dB @
100 Hz
The ‘CAL’ position is with all tone controls and Sensitivity
-10 dB function set to ‘off’
AMPLIFIER SECTION
Bass amplier power with an 8 Ohm load: 25 W
Treble amplier power with an 8 Ohm load: 25 W
Long term output power is limited by
overload protection circuitry
Amplier system distortion at nominal
output THD+N:
<0.08 %
Mains voltage: 100 - 240
V AC
Voltage operating range: ±10 %
Power consumption
Standby
Idle
Full output
<0.5 W
5 W
30 W

中文 7
8010A
有源监听系统
使用说明书
概述
Genelec 8010A是为专业应用设计的超紧凑型两分
频、双功放有源监听音箱。它包含驱动单元、功放、
有源分频滤波器以及保护电路。MDE™(Minimum
Diffraction Enclosure™)最低衍射箱体采用压铸铝
材质,音箱外型可减少箱体边缘的衍射。8010A采用
了先进的DCW™声波指向性控制技术(Directivity
Control Waveguide™),这一设计确保音箱即使处
于不佳的声学环境中也能具有优秀的频率平衡表现。
如果需要,可以配合使用合适的真力低音音箱来扩展
8010A的低频响应。
包装
每只8010A配有一条电源线和这本使用说明书。
安装注意事项
正确摆放音箱
请正确摆放音箱,让所有音箱的声轴都瞄准听音位置
的耳朵高度。垂直放置音箱是最佳选择,因为它能够
最大程度减轻分频点附近的声学抵消问题。
保持对称
请检查音箱放置是否对称,以及到达监听位置的距离
是否相等。如果可能,将监听位置放在房间的中线上,
且使音箱到中线距离相等。
最大限度减少反射
音箱附近的物体会产生声学反射,例如桌面、柜子、
电脑显示屏等,这些会引起不必要声染色和的声像
模糊。将音箱远离这些平面物体,可以尽量减少反射。
最小间距
如果音箱被安装在一个有限的空间内,例如放在柜子
内或嵌入墙体中,一定要确保功放充分冷却以及倒相
口工作正常。
音箱必须和四周,包括后方,上方和两侧保持至少2.5
厘 米( 1英寸)的间距。功放周围的空间必须通风或具
有足够大的散热空间,以确保环境温度不超过35摄氏
度( 95华氏度)。
连接
在完成音频信号线连接后方可连接电源线。
8010A包含一个阻抗10kOhm的平衡XLR输入接口。
也可以通过合适的转接器连接非平衡RCA线路电平
音频信号,详询真力经销商。由于8010A包含功放,因
此不需要额外的功放。切勿将8010A连接到功放、合
并功放或影音接收机的扬声器输出端口。
当音频连接完成后,使用附送的电源线将音箱接通电
源。音箱会自动启动。

8 中文
图1. 声轴位置
图3. 8010A背板上的控制和接口布局
图2. 5声道系统中正确的音箱的摆位方式

中文 9
表1:不同声学环境中建议的音色控制设置
音箱摆放环境 桌面控制 低频衰减
平直的消声室响应 关 关
吸声室内自由放置 关 关
混响室内自由放置 关 -2 dB
靠近墙 关 -4 dB
近场置于反射平面上 开( -4 dB @ 200Hz)-2 dB
放置在角落或箱子中 关 -6 dB
ISS™自动启动功能
8010A具备信号感应自动启动功能,播放开始时音
箱自动打开。当播放结束,电源会自动切换到待机
模式。待机模式的耗电不足0.5瓦。当检测到输入信
号,音箱电源会迅速自动启动。电源自动启动存在微
小的延时。如果不希望延时产生,将背板上的“禁用
ISS”开关调至“ON”,可以禁用ISS功能。这种情况
下,音箱通过背板上的电源开关来开启和关闭。
灵敏度调整
8010A的输入灵敏度(回放电平)有两个不同的设定:
正常和-10dB。正常设定为出厂设置,更低的-10dB
灵敏度可以通过将背板的“SENSITIVITY -10dB”
开关调至“ON”来开启。在这两个灵敏度下,输入电
平-6dBu时的输出声压级分别为100 dB和90 dB。请
选择合适的设置来得到所需的播放音量,同时确保前
级音量控制拥有良好的精度。
音色控制
通过设定音箱背面板的音色控制开关,调整真力
8010A的频率响应使之与声学环境相匹配。控制调整
参数包括“低频衰减”和“桌面控制”。表1列出了不同
环境中的几种典型设置。图4显示了在消声室内不同
音色控制的效果。
请确保在所有设定开关处于“OFF”位置时再开始系
统调整。通过测量或系统地聆听不同的设置组合来找
出最佳的频响平衡。
低音衰减
低音衰减(Bass Tilt)控制为低频响应提供了三个衰
减电平,通常在音箱放置于靠近房间边界位置时需要
开启。衰减电平包括-2dB(开关1“ON”),-4dB(开关
2“ON”)以 及 -6dB(两个开关均“ON”)。
桌面控制
2“ 桌 面( Desktop)”低频控制(开关3)在 200Hz处将低
频衰减4dB。这一功能用于补偿音箱置于桌面或类似
水平面之上所产生的低频增强。

10 中文
安装选件
8010A提供了多种安装选件:Iso-Pod™(Isolation
Positioner/Decoupler™)隔振底座可以使音箱倾斜
以指向听音者。音箱背面有三对螺纹孔,适配不同类
型的支架。如需要安装选件的完整列表,请查阅www.
genelec.com上的真力附件目录或联系您的真力经
销商。
维护
在音箱内没有需要用户维修的零部件。任何关于
8010A的维护或维修都应由具有维修服务资质的人
员来完成。
安全注意事项
尽管8010A已经按照国际安全标准设计,仍应注意以
下警告和注意事项,确保安全的操作以及安全的音箱
工作条件:
• 音箱维修和调整必须由具有维修资质的人员来
完成。不可打开音箱。
• 切勿将音箱靠近水或潮湿环境。切勿在音箱上
或其附近任何地方摆放充满液体的物品,例如
花瓶。
• 此音箱可以产生超过85dB的声压级,这可能会
引起永久性听力损伤。
• 确保音箱后方空气流动,使音箱能够充分冷却。
不要阻碍音箱周围的气流。
• 除非将电源线从功放上或电源插座上拔掉,否
则功放并未完全与交流电源断开连接。
质保
产品为材料和工艺上的瑕疵提供2年质保。请参考供
货商的销售和质保条款。
FCC符合性声明
该设备符合FCC规定的第15部分。操作必须符合以下两个条件:
(1)此设备不造成有害干扰
(2)设备必须接受所收到的干扰,包括可能导致意外操作的干扰
注意:该设备已经经过测试,符合B类数字设备的限制,且符合FCC
标准第15部分的要求。这些限制旨在提供合理的保护,防止在住宅
区安装时产生有害干扰。该设备会产生,使用和辐射射频能量,如果
未按照说明安装和使用,则可能对无线通信造成有害干扰。但是,我
们不保证在特定安装中不产生干扰。如果设备对无线电和电视的接
受产生有害的干扰,用户可通过开关该设备进行验证,我们建议用
户采用下述中一种或多种手段进行干扰消除:
• 重新调整天线的方向和位置
• 加大该设备与接收器之间的距离
• 将该设备和接收器分别连接到不同电路的插座上
• 向经销商或有经验的无线电/电视技术人员寻求帮助
任何未经厂方许可的改动都将让用户丧失在FCC规定下操作设备
的权力。

中文 11
70
75
80
85
d
B
r
A
40 20k
70 100 200 500 1k 2k 5k 10k Hz
Genelec Oy 8010 (dBr) vs freq (Hz) 10 Jan 13
65
70
75
80
65
BASS TILT
DESKTOP
图4. 图上的曲线显示了
8010A的“ 低 音 衰 减 ”和“
桌面控制”在自由场响应
中的效果
70
75
80
85
d
B
r
A
40 20k
70 100 200 500 1k 2k 5k 10k Hz
Genelec Oy 8010 (dBr) vs freq (Hz) 10 Jan 13
65
15°
45°
0°
30°
60°
图5. 上方曲线组表示
8010A在1米处测得的水
平方向指向性特性。下方
曲线表示系统的声功率
响应。

12 中文
系统参数
低频截止频率, –6 dB: < 67 Hz
高频截止频率, –6 dB: >25 kHz
自由场频率响应(±2.5 dB):74 Hz–20 kHz
半开放空间内,轴上最大短时正弦波声
学输出,
100Hz~3kHz均值
@1m
@0.5m
>96 dB SPL
>102 dB SPL
在相同条件下,使用IEC计权噪声测试的
最大长期RMS声学输出(受驱动单元保护
电路限制):
>91 dB SPL
在调音台上方,使用音乐信号进行测试,在
距音箱1m处每对音箱最大峰值声学输出:
>105 dB
自由场内自身噪声电平 @1m 轴上: < 5 dB
总谐波失真 85dB SPL @1m,轴 上
频率: 70�400 Hz
>400 Hz
< 3 %
< 0.5 %
单元:
低音
高音
76 mm (3 in)
锥形
19 mm (3/4 in)
金属球顶
重量:1.5 kg (3.3 lb)
尺寸:
高 度( 含 Iso-Pod™ 底座)
高度(不含Iso-Pod™ 底座)
宽度
深度
195 mm (711/16 in)
181 mm (71/8 in)
121 mm (43/4 in)
115 mm (41/4 in)
分频部分
输入接口:XLR母座7kOhm: pin 1 gnd,
pin 2 + pin 3 -
获得1米处100dB SPL输出所需的输入电平:-6 dBu
(-10dB灵敏
度设置关闭)
相对最大输出的电平控制范围: -10 dB
(-10dB灵敏
度设置打开)
桌面控制操作范围: 0 to –4 dB @
200 Hz
分频点,低音/高音:3.0 kHz
低音衰减控制范围,-2dB步长: 0 to –6 dB @
100 Hz
“校准”位置是当所有音色控制以及输入灵敏度控制-10dB功能
设定在”off”的状态
功放部分
低音功放输出功率,8 Ohm负载::25 W
高音功放输出功率,8 Ohm负载:25 W
长期输出功率受驱动单元保护电路限制
在标称输出功率下功放系统THD+N: <0.08 %
电源电压: 100 - 240
交流电
电压工作范围:±10 %
功耗
待机
空闲
满输出
<0.5 W
5 W
30 W
Other manuals for 8010A
3
Table of contents
Popular Measuring Instrument manuals by other brands

otometrics
otometrics Aurical Hit Reference manual

Schaller
Schaller humimeter BLL operating manual

Michell Instruments
Michell Instruments OptiCal user manual

ScienTECH
ScienTECH AC2500 Setup and operating procedures

Vaisala
Vaisala K-PATENTS PR-43 instruction manual

Siemens
Siemens SITRANS TDL operating instructions