Generac Power Systems 0065791 User manual

Owner’s Manual
For
Stationary Industrial Generators
Standalone Gas
This manual should remain with the unit.
This manual must be used in conjunction
with the appropriate installation manual.
*ONLY QUALIFIED ELECTRICIANS OR
CONTRACTORS SHOULD ATTEMPT
INSTALLATION!
*DEADLY EXHAUST FUMES!
Models: 0065791, 0065771
Cover237 Rev. B 07/18 Manual Part No. 0K4775B

ii Owner’s Manual for Stationary Industrial Generators
(000393a)
WARNING
CANCER AND REPRODUCTIVE HARM
www.P65Warnings.ca.gov.

Table of Contents
Owner’s Manual for Stationary Industrial Generators iii
Section 1 Safety
1.1 Introduction .......................................................................................................................... 1
1.1.1 Installation, Operation, and Maintenance ..................................................................................... 1
1.1.2 How to Obtain Service ..................................................................................................................1
1.2 Safety Rules .......................................................................................................................... 2
1.3 General Hazards ................................................................................................................... 3
1.4 Electrical Hazards ................................................................................................................ 3
1.5 Fire Hazards .......................................................................................................................... 4
1.6 Explosion Hazards ............................................................................................................... 4
Section 2 General Information
2.1 Unit Identification ................................................................................................................. 5
2.1.1 Data Label ....................................................................................................................................5
2.1.2 Model Identification Code .............................................................................................................5
2.1.3 Voltage Code ................................................................................................................................6
2.2 Equipment Description ........................................................................................................ 6
2.2.1 Standard Generator Features ....................................................................................................... 6
2.2.2 Generator and Load Compatibility ................................................................................................ 6
2.2.3 Single-Phase “A” or “M” Code Units .............................................................................................7
2.2.4 Three-Phase Load Imbalance Limits ............................................................................................7
2.2.5 Ambient Condition Derate .............................................................................................................7
2.3 Engine/Generator Protective Devices ................................................................................ 7
2.3.1 Coolant Temperature Sensor ....................................................................................................... 7
2.3.2 Low Coolant Level Sensor ............................................................................................................7
2.3.3 Oil Pressure Sensor ......................................................................................................................7
2.3.4 Overspeed Shutdown ................................................................................................................... 7
2.3.5 Overcrank Shutdown ....................................................................................................................8
2.3.6 RPM Sensor Loss Shutdown ........................................................................................................8
2.3.7 Low Fuel Pressure Warning .........................................................................................................8
2.4 DC Fuses ............................................................................................................................... 8
2.5 Fuel System .......................................................................................................................... 8
2.5.1 Diesel Fuel System ....................................................................................................................... 8
2.5.2 Natural Gas Fuel System ..............................................................................................................8
2.5.3 LP Fuel System ............................................................................................................................8
2.5.3.1 LP Vapor Withdrawal Fuel System ....................................................................................... 9
2.5.3.2 LP Liquid Withdrawal Fuel System ....................................................................................... 9
2.5.3.3 Dual Fuel: NG/LP Fuel System............................................................................................. 9
Table of Contents

Table of Contents
iv Owner’s Manual for Stationary Industrial Generators
2.6 Specifications .......................................................................................................................9
2.6.1 Generator ..................................................................................................................................... 9
2.6.2 Engine Oil Recommendations ...................................................................................................... 9
2.6.3 Coolant ......................................................................................................................................... 9
2.6.4 Gearbox Lubrication (If Equipped) .............................................................................................. 10
2.7 Starting Aids (If Equipped) ................................................................................................10
2.7.1 Engine Coolant Heater ............................................................................................................... 10
2.7.2 Engine Oil Sump Heater ............................................................................................................. 10
2.7.3 Battery Warmer .......................................................................................................................... 10
Section 3 Operation
3.1 Generator Control and Operation .....................................................................................11
3.1.1 Grounding the Generator ............................................................................................................ 11
3.1.2 Generator AC Neutral Connections ............................................................................................ 11
3.1.3 Initial Startup ............................................................................................................................... 11
3.2 H-100 Panel Interface .........................................................................................................12
3.2.1 Emergency Stop Button .............................................................................................................. 12
3.2.2 Common Alarm Horn .................................................................................................................. 12
3.2.3 Key Switch .................................................................................................................................. 12
3.2.4 Left Display Window ................................................................................................................... 12
3.2.5 Right Display Window ................................................................................................................. 13
3.2.6 Arrow Keys Pad .......................................................................................................................... 13
3.2.7 Fuse Block .................................................................................................................................. 13
3.3 Additional Components .....................................................................................................14
3.3.1 Main Line Circuit Breaker ........................................................................................................... 14
3.3.2 Automatic Transfer Switch .......................................................................................................... 14
3.3.3 Automatic Battery Charger ......................................................................................................... 14
3.3.4 Engine Coolant Heater (If Equipped) .......................................................................................... 14
3.3.5 Engine Oil Sump Heater (If Equipped) ....................................................................................... 14
3.3.6 Battery Warmer (If Equipped) ..................................................................................................... 14
3.4 Alarm Response Procedures ............................................................................................15
3.4.1 Alarm Types ............................................................................................................................... 15
3.4.1.1 Warnings............................................................................................................................. 15
3.4.1.2 Non-Shutdown Alarms........................................................................................................ 15
3.4.1.3 Shutdown Alarms................................................................................................................ 15
3.4.2 Alarm Display Window ................................................................................................................ 15
3.4.3 General Fault Response Procedure ........................................................................................... 16
3.5 Operating the Unit with an Automatic Transfer Switch ..................................................16
3.6 Operating the Unit with a Manual Transfer Switch ..........................................................16
3.6.1 Manual Engine Startup and Transfer .......................................................................................... 17
3.6.2 Re-Transfer and Shutdown ........................................................................................................ 17

Table of Contents
Owner’s Manual for Stationary Industrial Generators v
Section 4 Maintenance
4.1 Maintenance Schedule ...................................................................................................... 19
4.1.1 Service Maintenance Intervals ....................................................................................................19
4.1.2 Maintenance Schedule ............................................................................................................... 20
4.1.3 Notes and Maintenance Item Explanations ................................................................................ 20
4.2 Extended Run-Time Maintenance Checks ....................................................................... 21
4.3 Maintenance Level 1A ........................................................................................................ 22
4.4 Maintenance Level 1 - Monthly ......................................................................................... 23
4.5 Maintenance Level 2 - Semi-Annual ................................................................................. 24
4.6 Maintenance Level 3 - Annual ........................................................................................... 25
4.7 Maintenance Level 4 - Bi-Annual ...................................................................................... 26
4.8 Disabling a Generator for Maintenance ........................................................................... 27
4.8.1 To Disable the Generator From Starting .....................................................................................27
4.8.2 Shutdown and Restart an Operating Generator .........................................................................27
4.9 Maintenance Tasks ............................................................................................................ 28
4.9.1 Visually Inspect Unit ...................................................................................................................28
4.9.2 Check Engine Fluids ...................................................................................................................28
4.9.2.1 Check Engine Oil Level....................................................................................................... 28
4.9.2.2 Check Coolant Level........................................................................................................... 29
4.9.2.3 Check/Change Gearbox Oil (If Equipped) .......................................................................... 29
4.9.3 Battery Inspection .......................................................................................................................30
4.9.4 Battery Installation and Replacement .........................................................................................31
4.9.5 Other Maintenance Checks ........................................................................................................ 33
4.10 Maintenance and Repair Parts ........................................................................................ 33

Table of Contents
vi Owner’s Manual for Stationary Industrial Generators
This page intentionally left blank.

Owner’s Manual for Stationary Industrial Generators 1
Section 1 Safety
1.1 — Introduction
Every effort was expended to ensure that the information and instructions in this manual were both accurate and cur-
rent at the time it was released. However, the manufacturer reserves the right to change, alter, or otherwise improve
this product at any time without prior notice.
Read this manual thoroughly. If any portion is not understood, contact the nearest Authorized Service Dealer for
starting, operating, and servicing procedures. The operator is responsible for proper and safe use of the equipment.
The manufacturer strongly recommends that the operator read this Owner’s Manual and thoroughly understand all
instructions before using this equipment. The manufacturer also strongly recommends having an Authorized Service
Dealer provide instruction to any designated operators in the safe inspection, starting, operating, and stopping of this
unit.
1.1.1— Installation, Operation, and Maintenance
Installation and initial startup of this equipment is not a “do-it-yourself”
project. This generator set must be installed by an Authorized Service
Dealer or other competent, qualified contractor. The initial startup must
be performed and documented by a factory Authorized Service Dealer. A
factory Authorized Service Dealer can also provide the necessary train-
ing for authorized operators. It is the operator’s responsibility to perform
all safety checks, to make sure that all maintenance for safe operation is
performed promptly, and to have the equipment checked periodically by
an Authorized Service Dealer. Normal maintenance service and replace-
ment of parts are the responsibility of the owner/operator and, as such,
are not considered defects in materials or workmanship within the terms
of the warranty. Individual operating habits and usage contribute to the
need for maintenance service.
Proper maintenance and care of the generator will ensure a minimum
number of problems and keep operating expenses at a minimum. See
an Authorized Service Dealer for service aids and accessories.
1.1.2— How to Obtain Service
NOTE: Use this page to record important information about the
generator set.
Each generator set has a DATA LABEL containing important information
about the unit.
When contacting an Authorized Service Dealer about parts and/or ser-
vice, always supply the complete model number and serial number of
the unit as given on the data label. For quick and easy reference, copy
the information printed on the Data Label located on the generator onto
the sample label printed here. See Figure 1-1.
Figure 1-1. Data Label (Sample)

Safety
2Owner’s Manual for Stationary Industrial Generators
1.2 — Safety Rules
Throughout this publication, and on tags and decals affixed to the generator, DANGER, WARNING, CAUTION, and
NOTE boxes are used to alert personnel to special instructions about a particular operation that may be hazardous if per-
formed incorrectly or carelessly. Observe them carefully. They indicate:
INDICATES A HAZARDOUS SITUATION OR ACTION WHICH, IF NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.
Indicates a hazardous situation or action which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTE: Notes provide additional information important to an operation or procedure.
Four commonly used safety symbols accompany the DANGER, WARNING and CAUTION blocks. The type of informa-
tion each indicates is as follows:
This symbol points out important Safety Information that, if not followed, could endanger personal safety and/or
property.
This symbol points out a potential Explosion Hazard.
This symbol points out a potential Fire Hazard.
This symbol points out a potential Electrical Shock Hazard.
SAVE THESE INSTRUCTIONS. This manual contains important instructions that should be followed
during operation and maintenance of the generator and batteries. The manufacturer suggests that these
rules for safe operation be copied and posted in potential hazard areas. Safety should be stressed to all
operators, potential operators, and service and repair technicians for this equipment.
Study these Safety Rules carefully before operating or servicing this equipment. Become familiar with this Owner’s Man-
ual and with the unit. The generator can operate safely, efficiently, and reliably only if it is properly installed, operated, and
maintained. Many accidents are caused by failing to follow simple and fundamental rules or precautions.
The manufacturer cannot anticipate every possible circumstance that might involve a hazard. The warnings in this man-
ual, and on tags and decals affixed to the unit are, therefore, not all-inclusive. If using a procedure, work method, or oper-
ating technique the manufacturer does not specifically recommend, ensure that it is safe for others. Also make sure the
procedure, work method, or operating technique utilized does not render the generator unsafe.
•Despite the safe design of this generator, operating the equipment imprudently, neglecting its maintenance, or
being careless can cause possible injury or death. Permit only responsible and capable persons to install, operate,
and maintain this equipment.
•Parts of the generator are rotating and/or hot during operation. Exercise care near running generators.
•The installation must always comply with applicable codes, standards, laws and regulations.
*
$
!
+
*

Safety
Owner’s Manual for Stationary Industrial Generators 3
•If the generator is used to power electrical load circuits normally powered by a utility power source, installation of
a transfer switch is required. The transfer switch must effectively isolate the electrical system from the utility dis-
tribution system when the generator is operating. Failure to isolate an electrical system by such means will result
in damage to the generator and also may result in injury or death to utility power workers due to backfeed of elec-
trical energy.
•Potentially lethal voltages are generated by this equipment. Ensure all steps are taken to make the unit safe
before attempting any work on the generator.
1.3 — General Hazards
•For safety reasons, the manufacturer recommends that this equipment be installed, serviced, and repaired by an
Authorized Service Dealer or other competent, qualified electrician or installation technician who is familiar with
applicable codes, standards, and regulations. The operator also must comply with all such codes, standards, and
regulations.
•Installation, operation, servicing, and repair of this (and related) equipment must comply with all applicable
codes, standards, laws, and regulatory requirements. Also, ensure that the generator is installed, operated, and
serviced in accordance with the manufacturer’s instructions and recommendations. Following installation, do
nothing that might render the unit unsafe or in noncompliance with the aforementioned codes, standards, laws,
and regulations.
•The engine exhaust fumes contain carbon monoxide, which can be DEADLY. This dangerous gas, if breathed in
sufficient concentrations, can cause unconsciousness or even death. For this reason, adequate ventilation must
be provided. Exhaust gases must be piped safely away from any building or enclosure that houses the generator
to an area where people, animals, etc. will not be harmed. This exhaust system must be installed properly, in
strict compliance with applicable codes and standards.
•Keep hands, feet, clothing, etc. away from drive belts, fans, and other moving or hot parts. Never remove any
drive belt or fan guard while the unit is operating. Ensure that all guards, covers, and protective devices removed
during maintenance or service are reinstalled.
•Adequate, unobstructed flow of cooling and ventilating air is critical in any room or building housing the generator
to prevent buildup of explosive gases and to ensure correct generator operation. Do not alter the installation or
permit even partial blockage of ventilation provisions, as this can seriously affect safe operation of the generator.
•Keep the area around the generator clean and uncluttered. Remove any materials that could become hazardous.
•When working on this equipment, remain alert at all times. Never work on the equipment when physically or men-
tally fatigued.
•Inspect the generator regularly, and promptly repair or replace any worn, damaged, or defective parts using only
factory approved parts.
•Before performing any maintenance on the generator, disconnect the battery cables to prevent accidental
startup. Disconnect the cable from the battery post indicated by a NEGATIVE, NEG, or (–) first, then remove the
POSITIVE, POS, or (+) cable. When reconnecting the cables, connect the POSITIVE cable first, the NEGATIVE
cable last.
•Never use the generator or any of its parts as a step. Stepping on the unit can stress and break parts, and may
result in dangerous operating conditions from leaking exhaust gases, fuel leakage, oil leakage, etc.
1.4 — Electrical Hazards
•All generators covered by this manual produce dangerous electrical voltages and can cause fatal electrical
shock. Utility power delivers extremely high and dangerous voltages to the transfer switch as well as the station-
ary emergency generator when it is in operation. Avoid contact with bare wires, terminals, connections, etc. on
the generator as well as the transfer switch, if applicable. Ensure all appropriate covers, guards, and barriers are
in place, secured and/or locked before operating the generator. If work must be done around an operating unit,
stand on an insulated, dry surface to reduce potential shock hazard.
•Do not handle any kind of electrical device while standing in water, while barefoot, or while hands or feet are wet.
DANGEROUS ELECTRICAL SHOCK MAY RESULT.

Safety
4Owner’s Manual for Stationary Industrial Generators
•If people must stand on metal or concrete while installing, operating, servicing, adjusting, or repairing this equip-
ment, place insulative mats over a dry wooden platform. Work on the equipment only while standing on such
insulative mats.
•The generator must be grounded in accordance with all code and regulatory requirements.
•Wire gauge sizes of electrical wiring, cables, and cord sets must be adequate to handle the maximum electrical
current (ampacity) to which they will be subjected.
•Before installing or servicing this (and related) equipment, make sure that all power voltage supplies are posi-
tively turned off at their sources. Failure to do so will result in hazardous and possibly fatal electrical shock.
•Connecting this unit to an electrical system normally supplied by an electric utility shall be by means of a transfer
switch so as to isolate the generator electric system from the electric utility distribution system when the genera-
tor is operating. Failure to isolate the two electric system power sources from each other by such means will
result in damage to the generator and may also result in injury or death to utility power workers due to backfeed
of electrical energy.
•Generators installed with an automatic transfer switch will crank and start automatically when NORMAL (UTIL-
ITY) source voltage is removed or is below an acceptable preset level. To prevent such automatic startup and
possible injury to personnel, disable the generator’s automatic start circuit (battery cables, etc.) before working
on or around the unit. Then place a “DO NOT OPERATE” tag on the generator control panel and on the transfer
switch.
•In case of accident caused by electric shock, immediately shut down the source of electrical power. If this is not
possible, attempt to free the victim from the live conductor. AVOID DIRECT CONTACT WITH THE VICTIM. Use
a nonconducting implement, such as a dry rope or board, to free the victim from the live conductor. If the victim is
unconscious, apply first aid and get immediate medical help.
•Never wear jewelry when working on this equipment. Jewelry can conduct electricity resulting in electric shock,
or may get caught in moving components resulting in injury.
1.5 — Fire Hazards
•Keep a fire extinguisher near the generator at all times. DO NOT use any carbon tetra-chloride type extinguisher.
Its fumes are toxic, and the liquid can deteriorate wiring insulation. Keep the extinguisher properly charged and
be familiar with its use. If there are any questions pertaining to fire extinguishers, consult the local fire depart-
ment.
•All fuel types are potentially FLAMMABLE and/or EXPLOSIVE and should be handled with care.
1.6 — Explosion Hazards
•Properly ventilate any room or building housing the generator to prevent buildup of explosive gas.
•Do not smoke around the generator. Wipe up any fuel or oil spills immediately. Ensure that no combustible mate-
rials are left in the generator compartment, or on or near the generator, as FIRE or EXPLOSION may result.
Keep the area surrounding the generator clean and free from debris.
•All fuel types are potentially FLAMMABLE and/or EXPLOSIVE and should be handled with care. Comply with all
laws regulating the storage and handling of fuels. Inspect the unit’s fuel system frequently and correct any leaks
immediately. Fuel supply lines must be properly installed, purged, and leak tested according to applicable fuel-
gas codes before placing this equipment into service.

Owner’s Manual for Stationary Industrial Generators 5
Section 2 General Information
2.1 — Unit Identification
2.1.1— Data Label
Each generator set has a DATA LABEL containing important information about the generator. The data label lists the
unit serial number, rated voltage, amps, wattage capacity, etc.
NOTE: The figure below is a generic representation only. For actual information on your particular model, refer
to the data label(s) affixed to your unit.
2.1.2— Model Identification Code
The model identification code gives important information about the generator set. For example, if the code is:
SG 0100 A G03 6.8 N 23 H B Y Y 3
Then the generator would have the attributes shown in bold below:
SG Stationary gaseous generator.
SD Stationary diesel generator.
0100 Rated output is 100,000 watts (100kW).
A Voltage code (see Subsection 2.1.3).
G03 Indicates engine MFG (for manufacturer’s use).
6.8 Engine is 6.8 liter.
NNatural Gas fuel system.
L LP Liquid Withdrawal fuel system.
V LP Vapor Withdrawal fuel system.
R Dual fuel system with LP liquid as secondary.
P Dual fuel system with LP Vapor as secondary.
D Diesel fuel system.
23
2,300 Engine rpm rating (15 = 1500 rpm, 18 = 1,800 rpm, etc.)
NOTE: Engines operating above 1,500 or 1,800 rpm use a gearbox
to reduce the engine rpm to the desired alternator rotor rpm of 1,500
rpm (50 Hz operation) or 1,800 rpm (60 Hz operation).
HUnit has optional “H” control panel.
BBrushless excitation.
P Permanent magnet excitation.
YStandard enclosure equipped.
N No enclosure — suitable for indoor installation.
S Level 1 sound attenuation.
L Level 2 sound attenuation.
YExhaust muffler mounted.
N Exhaust muffler not provided.
L Exhaust muffler shipped loose with unit.
3Emission designation (for factory use).
SG0100AG036.8N23HBYY3
Sample

General Information
6Owner’s Manual for Stationary Industrial Generators
2.1.3— Voltage Code
The letter following the kilowatt rating in the model identification code is the voltage code. The voltage code indicates
the following:
2.2 — Equipment Description
This equipment is a revolving field, alternating current type generator set. The generator is designed to supply electrical
power for the operation of compatible electrical loads when the utility power supply is not available or has dropped to
an unacceptable level.
The generator’s revolving field is directly connected to and driven by an engine by means of flexible discs or a gearbox.
Generators with a four-pole rotor are driven at a rated speed of 1,800 rpm to supply a frequency of 60 Hertz. Four-pole
rotors operating at 50 Hertz are driven at 1,500 rpm.
Refer to the data label affixed to the unit for rated AC voltage, wattage, amperage, number of phases, etc. See Subsec-
tion 2.1.2 for an explanation of how to identify the unit’s features.
2.2.1— Standard Generator Features
The generator incorporates the following features:
•The rotor insulation system is Class “H” rated, and the stator insulation is Class “H” rated as defined by NEMA
MG1-22.4 and NEMA MG1-1.65.
•The generator is self-ventilated and drip-proof constructed.
•The voltage waveform deviation, total harmonic content of the AC waveform and “telephone influence factor”
have been evaluated and are acceptable according to NEMA MG1-22.
•All prototype tested models have passed three-phase symmetrical short circuit test to ensure system protection
and reliability.
2.2.2— Generator and Load Compatibility
The generator must be fully compatible with the rated voltage, phase, and frequency of the connected electrical loads.
The generator, connected electrical devices, or both, can be damaged if voltage, phase, and frequency are not compat-
ible.
Code Description
A 120/240 volts, single-phase, four-lead, 60 Hz
D 120/240 volts, single- and three-phase, 12-lead, 60 Hz
G 120/208 volts, three-phase, 12-lead, 60 Hz Broad Range
H 231/400 volts, three-phase, 12-lead, 60 Hz Broad Range
J 120/240 volts, three-phase, 12-lead, 60 Hz Broad Range
K 277/480 volts, three-phase, 12-lead, 60 Hz Broad Range
L 346/600 volts, three-phase, six-lead, 60 Hz
M 110/220 volts, single-phase, four-lead, 50 hz
N 115/200 volts, three-phase, 12-lead, 50 Hz Broad Range
P 100/200 volts, three-phase, 12-lead, 50 Hz Broad Range
R 231/400 volts, three-phase, 12-lead, 50 Hz Broad Range
S 277/480 volts, three-phase, six-lead, 50 Hz

General Information
Owner’s Manual for Stationary Industrial Generators 7
NOTE: This manual assumes that the generator set has been properly selected, installed and interconnected
by a competent, qualified electrician or installation contractor. Once the installation is complete, do nothing
that may result in non-compatibility between the generator and connected electrical loads.
2.2.3— Single-Phase “A” or “M” Code Units
The following statement applies to single-phase units with an “A” or “M” code alternator:
The generator is suitable for supplying typical residential loads, such as induction motors (sump pumps, refrigerators,
air conditioners, furnaces, etc.), electronic components (TV, computer, monitor, etc.), lighting loads, and microwaves.
2.2.4— Three-Phase Load Imbalance Limits
For three-phase units the maximum load imbalance between phases can not exceed 25% of rated load (current).
2.2.5— Ambient Condition Derate
The maximum ambient temperature for the generator is indicated on the unit data label. Derate values for ambient tem-
perature in excess of that indicated on the data label, as well as altitude, may apply depending on the engine and kW
rating of the unit. Consult an Authorized Service Dealer for any derate values applicable to this specific generator at its
installed location.
2.3 — Engine/Generator Protective Devices
The generator set may be required to operate for long periods of time without an operator on hand to monitor condi-
tions such as coolant temperature, oil pressure, voltage, frequency, etc. For this reason, the generator set has numer-
ous sensors to provide the control panel with the information it needs to protect both the engine and generator. The
control panel is designed to shut down the engine if potentially damaging conditions occur. These conditions can
include low oil pressure, high coolant temperature, low coolant level, engine overspeed, over or under voltage, over or
under frequency, etc. These settings are configured at the factory and can be changed/adjusted by an Authorized Ser-
vice Technician if required.
NOTE: Engine/generator protective devices are only mentioned here for the owner/operator’s general informa-
tion. For details, consult the applicable control panel technical manual. The list below is not all inclusive.
2.3.1— Coolant Temperature Sensor
The control panel automatically shuts down the engine if the engine coolant temperature rises above a safe level.
2.3.2— Low Coolant Level Sensor
Should the engine coolant level drop below the level of the low coolant temperature sensor, it is possible for the engine
to overheat without automatic shutdown. To prevent such overheating, the engine has a low coolant level sensor. If the
level of engine coolant drops below the level of the low coolant level sensor, the control panel will shut the engine
down.
2.3.3— Oil Pressure Sensor
This sensor monitors engine oil pressure. If oil pressure drops below a safe level, the control system automatically
shuts down the engine.
2.3.4— Overspeed Shutdown
A speed circuit controls engine cranking, startup, operation, and shutdown. Engine speed signals are delivered to the
control panel whenever the unit is running. Should the engine overspeed above a safe, preset value, the control panel
initiates an automatic engine shutdown.

General Information
8Owner’s Manual for Stationary Industrial Generators
2.3.5— Overcrank Shutdown
After a pre-specified duration of cranking, this function ends the cranking if the engine has failed to start. The default
settings are:
•The unit will attempt to start (crank) three times.
•Each crank cycle lasts either 10 or 15 seconds, followed by a five second rest (to cool the starter).
•After three starting attempts the unit will shutdown.
2.3.6— RPM Sensor Loss Shutdown
If the speed signal to the control panel is lost, engine shutdown will occur.
2.3.7— Low Fuel Pressure Warning
•Some gaseous units are equipped with a low fuel pressure warning switch which will trigger a Warning alarm if
the fuel pressure drops below a minimum setting.
•Diesel units with fuel tanks are equipped with High and Low fuel level warning alarms, as well as a low fuel level
shutdown alarm.
2.4 — DC Fuses
Located inside the front panel, the fuses protect the control panel wiring and components from damaging overload. For
fuse location and identification, see Figure 3-4.
2.5 — Fuel System
This generator set is equipped with one of the following fuel systems:
•Diesel fuel system
•Natural Gas (NG) fuel system
•LP gas vapor withdrawal fuel system (LPV)
•LP gas liquid withdrawal fuel system (LPL)
•Dual fuel system: Natural Gas (primary fuel source), LP gas vapor (secondary fuel source)
•Dual fuel system: Natural Gas (primary fuel source, LP gas liquid (secondary fuel source)
2.5.1— Diesel Fuel System
The manufacturer recommends the use of No. 2 diesel fuel when temperatures are above freezing, and No. 1 diesel
fuel when temperatures drop below freezing. Diesel fuel must meet the following requirements:
Beginning October 1, 2010, owners and operators that use diesel fuel must use diesel fuel that meets:
•Sulfur content of 15 parts per million (ppm) maximum.
•Cetane index or aromatic content as follows: A minimum cetane index of 40, or a maximum aromatic content of
35 volume percent.
2.5.2— Natural Gas Fuel System
Natural gas is supplied by a local utility in its vapor state through in ground piping.
2.5.3— LP Fuel System
LP is supplied as a liquid in pressurized tanks. It is usually made up of propane, butane, or a mixture of both gases.

General Information
Owner’s Manual for Stationary Industrial Generators 9
2.5.3.1—LP Vapor Withdrawal Fuel System
Utilizes the vapors formed above the liquid fuel in the supply tank. Approximately 10 to 20 percent of the tank capacity
is needed for fuel expansion from the liquid to the vapor state.
2.5.3.2—LP Liquid Withdrawal Fuel System
LP in a liquid withdrawal system must be converted to its gaseous state before it is introduced into the engine carbure-
tor. A vaporizer converter is used to accomplish this. In such a converter, heated engine coolant is ported through the
converter to provide the necessary heat for conversion of the fuel from a liquid to a gaseous state.
NOTE: Units with LP gas liquid withdrawal systems incorporate a block heater as standard equipment. The
heater is powered by the utility power source during non-operating periods to provide heated coolant to aid in
the fuel vaporization process.
2.5.3.3—Dual Fuel: NG/LP Fuel System
Some applications require the use of a “dual-fuel” system. This type of fuel system allows the generator to run on either
natural gas (primary) or LP vapor or liquid (secondary). In the event that the primary source (utility supplied) becomes
unavailable, the unit automatically switches to the secondary source. It can do so while in operation or while not oper-
ating.
2.6 — Specifications
2.6.1— Generator
Refer to the data plate on the generator for rated watts, amperes, frequency, voltage, phase, and other important infor-
mation.
2.6.2— Engine Oil Recommendations
The engine has been filled with factory engine oil of a grade recommended by the engine supplier as follows:
•Gaseous Engines: 6.8L displacement or smaller - SAE 5W-20; Displacement larger than 6.8L - SAE 40.
•Diesel Engines: SAE 15W-40
The manufacturer recommends an initial oil and filter change after the first 50 hours (or first 3 months) of service oper-
ation. Use a high quality detergent oil with an appropriate classification and viscosity for the engine type and ambient
temperature conditions. Consult your Authorized Servicing Dealer for oil recommendations. Synthetic oils meeting the
same service category and viscosity requirements for the application may be used.
•Recommended API Service Category for gaseous engines: SJ, SL, SM, or SN.
•Recommended API Service Category for diesel engines: CH-4, CI-4, or CJ-4
2.6.3— Coolant
Use only deionized or distilled water and Ethylene glycol antifreeze (Propylene glycol can also be used but do not mix
with Ethylene glycol). When adding coolant, always add the recommended 50-50 mixture.

General Information
10 Owner’s Manual for Stationary Industrial Generators
●DO NOT remove the radiator pressure cap while the engine is hot. Serious burns from boiling liquid
or steam could result.
●Ethylene glycol base antifreeze is poisonous. Do not use mouth-to-siphon coolant from the radiator,
recovery bottle, or any container. Wash hands thoroughly after handling. Never store used antifreeze
in an open container because animals are attracted to the smell and the taste of antifreeze even
though it is poisonous.
Do not use any chromate base rust inhibitor with propylene glycol base antifreeze. Using any high sil-
icate antifreeze boosters or additives also will cause overheating. The manufacturer also recommends
that any soluble oil inhibitor is NOT USED for this equipment.
2.6.4— Gearbox Lubrication (If Equipped)
Use only SAE 90 gear oil with the correct proportion of Lucas Heavy Duty Oil Stabilizer. See the Maintenance section
for more information.
2.7 — Starting Aids (If Equipped)
One or more of the following starting aids may be provided to ensure quicker, easier starts under varying climactic con-
ditions.
•Engine coolant heater
•Engine oil heater
•Battery warmer
These aids are powered by a normal (utility) power source during non-operating periods.
2.7.1— Engine Coolant Heater
Heats the engine coolant when the unit is not operating. This action keeps the engine warm even in cold weather, help-
ing to ensure quicker starts. Powered by a circuit normally fed by the utility power supply.
2.7.2— Engine Oil Sump Heater
Keeps the oil in the sump heated to allow easier starting and faster engine warm-up. Powered by a circuit normally fed
by the utility power supply.
2.7.3— Battery Warmer
Keeps the battery warm so it can provide full cranking current when starting in cold conditions. Powered by a circuit
normally fed by the utility power supply.
*
*

Owner’s Manual for Stationary Industrial Generators 11
Section 3 Operation
3.1 — Generator Control and Operation
The operation of this generator set should only be performed by an “Authorized Operator,” that is, someone who has
been properly trained by an Authorized Service Dealer. Contact your local Authorized Service Dealer for assistance in
training Authorized Operators.
The following instructions assume that the generator has been properly installed, serviced, tested, adjusted, and other-
wise prepared for use by a competent, qualified installation contractor and Authorized Service Dealer. Carefully read
the Safety Rules and any other safety information before attempting to operate this (and related) equipment.
3.1.1— Grounding the Generator
Ground the generator set in accordance with all codes and regulatory requirements.
DO NOT connect the ground wire to any pipe that carries a flammable or explosive substance as FIRE
or EXPLOSION may result.
Figure 3-1. Grounding Electrode Terminal (Typical)
3.1.2— Generator AC Neutral Connections
Grounding is recommended only at one point in the system. Consult local building codes for proper neutral grounding
requirements.
3.1.3— Initial Startup
The initial startup of the generator set must be performed and documented by an Authorized Service Dealer.
$
Base Frame
Grounding Electrode
Terminal

Operation
12 Owner’s Manual for Stationary Industrial Generators
3.2 — H-100 Panel Interface
The H-100 Panel Interface mounted on the generator allows the operator to monitor, and if necessary, manually start
the generator.
3.2.1— Emergency Stop Button
The red Emergency Stop Button is the top button on the right side of the panel. Pressing the button while the unit is run-
ning will immediately shut the generator down. To restart the unit, the Emergency Stop Button must be manually reset,
the Key Switch turned to the “OFF” position, and then turned to either the “AUTO” or “MAN” position, depending on the
desired mode of operation.
3.2.2— Common Alarm Horn
Directly below the Emergency Stop Button is a Common Alarm Horn. The “Common Alarm and Digital Output Function
#1” are activated whenever a fault condition is set for “Alarm” and if the fault is “Active.” The Common Alarm will not
activate on “Warnings” or “DTC” fault conditions. Pressing the “ENTER” button on the key pad will acknowledge the
alarm and silence the horn. The manufacturer recommends that the local service dealer be notified of any alarm condi-
tion in order for qualified service personnel to assess and correct the situation.
Figure 3-2. H-100 Control Panel Interface
3.2.3— Key Switch
A manual three-position Key Switch is located beneath the Common Alarm Horn. The positions are:
•AUTO: The generator will automatically start when a properly connected automatic transfer switch senses a loss
or reduction of available utility power.
•OFF: Immediately shuts down the generator and/or prevents it from starting automatically.
•MAN: Immediately starts the generator.
3.2.4— Left Display Window
The Left Display Window can be configured to display different menus. See the H-100 Operations Manual for more
information. Normally, the following information is displayed:
•Volts •Amps •Frequency
•Hertz •Kilowatts

Operation
Owner’s Manual for Stationary Industrial Generators 13
3.2.5— Right Display Window
The Right Display Window displays:
•Alarm information
•HOME menu: basic engine menu information, such as oil pressure, oil temperature, water temperature, battery
voltage
•MENU: main menu navigation screen
Figure 3-3. Right Display Window (Press MENU)
3.2.6— Arrow Keys Pad
The key pad contains four arrow keys, a HOME key, a MENU key, and an ENTER key. Two LEDs are also present, one
labeled NOT IN AUTO and the other ALARM.
Use the arrow keys to navigate through the menus displayed in the Display Windows. For example, when the HOME
key is pressed, the HOME menu is displayed in the Right Display Window. When a flashing cursor appears within a line
of the text, move the cursor up, down, left, or right by pressing the corresponding arrow key.
The NOT IN AUTO LED flashes once each second when the Key Switch is moved to the OFF or MAN positions.
During normal operation when no alarms are present, the ALARM LED flashes for one second every 30 seconds
(approximate) to indicate that the panel is operational. When an active alarm condition is detected, the ALARM LED
flashes once each second. The LED remains ON if the alarm condition is acknowledged, but still active.
3.2.7— Fuse Block
The fuse block is located inside the control panel at the back lower left corner. The 10 amp fuse in the F2 slot is the
control panel fuse.
Figure 3-4. Panel Fuse Block
NOTE: Some units will NOT have a fuse in the F4 slot.
Alarms Left Display
Engine Generator
Status Diagnostic
Service Exercise/HTS

Operation
14 Owner’s Manual for Stationary Industrial Generators
3.3 — Additional Components
3.3.1— Main Line Circuit Breaker
A Main Line Circuit Breaker (MLCB) is located on the face of the High Voltage Customer Connections panel, typically
situated to the right of the H-100 Control Panel. The MLCB serves as the means of disconnect at the generator, to dis-
connect it from the Transfer Switch.
3.3.2— Automatic Transfer Switch
A typical automatic transfer switch monitors utility voltage and when that voltage falls outside of specific parameters, it
will initiate the generator start command. As long as the generator control is in the AUTO position, it responds to the
automatic transfer switch start command.
For information about any connected automatic transfer switch, consult the applicable transfer switch owner’s manual.
Connecting this generator to an electrical system normally supplied by an electric utility shall be by
means of a transfer switch (either fully automatic or manual), so as to isolate the electric system from
the utility distribution system when the generator is operating. Failure to isolate the electric system by
these means will result in damage to the generator and may also result in injury or death to utility
workers due to backfeed of electrical energy.
3.3.3— Automatic Battery Charger
One of the following types of battery chargers may be provided:
•2.5-amp
•10-amp
The 2.5-amp charger is 12 VDC only. The 10-amp charger is available either as a 12 VDC or 24 VDC, as appropriate
for the engine’s DC system voltage.
Both chargers are fully automatic float types and are fully fuse protected (input and output). They have automatic cur-
rent limiting to reduce risk of overcharging, and have automatic maintenance of charge voltage. Therefore, they can be
connected to the batteries continuously.
The chargers require the connection of a charged battery in order to turn on. The battery provides boost voltage for the
charger, so a completely dead battery will not allow the charger to operate. The boost required is approximately 9 to 11
volts for a 12 VDC system, and 18 to 22 volts for a 24 VDC system. Replace the battery if it is below the boost voltage.
3.3.4— Engine Coolant Heater (If Equipped)
Heats the engine coolant when the unit is not operating. This action keeps the engine warm even in cold weather, help-
ing to ensure quicker starts. Powered by a circuit normally fed by the utility power supply.
3.3.5— Engine Oil Sump Heater (If Equipped)
Keeps the oil in the sump heated to allow easier starting and faster engine warm-up. Powered by a circuit normally fed
by the utility power supply.
3.3.6— Battery Warmer (If Equipped)
Keeps the battery warm so it can provide full cranking current when starting in cold conditions. Powered by a circuit
normally fed by the utility power supply.
$