Generac Power Systems 5500XL User manual

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
Problems?
Questions?
Before taking your unit
back to the store,
call the generator
helpline at
1-800-270-1 08
M-F 8-5 CT
Model No. 988 -3 ( , 00 Watt AC Generator) Part No. B2674 Revision 2 (6/28/2000)
Visit our Generac website: www.generac-portables.com
Portable Generator Owner’s Manual
DANGER! This generator is designed for outdoor use only. Never use this generator inside any building
or enclosure including the generator compartment of a recreational vehicle (RV). Carbon monoxide
poisoning, fire and/or an explosion may result. No user performed modifications, including venting of
exhaust and/or cooling ventilation, will eliminate the danger. Always have at least two feet of clearance on
all sides of the generator while operating the unit outdoors.
DANGER! You must isolate the generator from the electric utility by opening the electrical systems main
circuit breaker or main switch if this unit is used for backup power. Failure to isolate the generator from
the power utility may result in injury or death to electric utility workers and damage to the
generator due to a backfeed of electrical energy.
The Emission Control System for this generator is warranted for standards set by the
Environmental Protection Agency. For warranty information refer to the engine owners manual.
5500XL

Generac Portable Products 00XL Extended Life Generator
2
EQUIPMENT DESCRIPTION
This generator is an engine-driven, revolving field,
alternating current (AC) generator. It was designed to
supply electrical power for operating compatible
electrical lighting, appliance, tool and motor loads.
This manual contains information for a generator that
operates 120 and/or 240 Volts AC, single phase,
60 Hz devices that require up to , 00 watts ( . kW)
of power that pull up to 4 .8 Amps at 120 Volts or
22.9 Amps at 240 Volts.
CAUTION! Do Not exceed the generators
wattage/amperage capacity. Add up the rated
watts of all devices you are connecting to
generator receptacles at one time. This total
should not be greater than , 00 watts. See
Dont Overload The Generator on page 10.
The 00XL generator has the following features:
 120/240 Volt AC, 30 Amp locking receptacle, a
120 Volt AC, 30 Amp locking receptacle, a
120 Volt AC, 1 Amp duplex receptacle, and a
12 Volt DC, 10 Amp receptacle.
 Low Oil Shutdown: Automatically shuts down the
engine if oil drops below safe operation level.
 Seven gallon overhead fuel tank with fuel gauge.
 The generators revolving field is driven at
approximately 3,600 rpm by a Generac Power
Systems 11 HP engine.
DANGER! Do Not tamper with engine
governed speed. High operating speeds are
dangerous and increase risk of personal injury
or damage to equipment. The generator
supplies correct rated frequency and voltage
only when running at proper governed speed.
Incorrect frequency and/or voltage can damage
some connected electrical loads. Operating at
excessively low speeds imposes a heavy load.
When adequate engine power is not available,
engine life may be shortened.
SAFETY RULES
This generator set was designed and manufactured
for specific applications. Do Not attempt to modify the
unit or use it for any application it was not designed
for. If you have any questions about your generators
application, ask your dealer or consult the factory.
The manufacturer could not possibly anticipate every
circumstance that might involve a hazard. For that
reason, warnings in the manual and warnings on tags
or decals affixed to the unit are not allinclusive. If you
intend to handle, operate or service the unit by a
procedure or method not specifically recommended by
the manufacturer, first make sure that such a
procedure or method will not render this equipment
unsafe or pose a threat to you and others.
Read this manual carefully and become familiar
with your generator set. Know its applications, its
limitations and any hazards involved.
DANGER! You must isolate the generator from
the electric utility using approved transfer
equipment if this unit is used for backup power.
Failure to isolate the generator from the
power utility may result in injury or death to
electric utility workers and damage to the
generator due to a backfeed of electrical
energy. Whenever unit is providing backup
power, the electric utility must be notified.
DANGER! Generator exhaust gases contain
DEADLY carbon monoxide gas. If breathed
in sufficient concentrations, carbon
monoxide can cause unconsciousness or
death. Operate this equipment outdoors where
adequate ventilation is available.
 The generator produces a very powerful voltage that
can cause serious injury or death by electrocution.
Never touch bare wires or receptacles. Never
permit a child or unqualified person to operate the
generator.
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects, or other reproductive harm.
WARNING:

Generac Portable Products 00XL Extended Life Generator
3
Never handle any kind of electrical cord or device
while standing in water, while barefoot, or while
hands or feet are wet. Death or serious injury from
electrocution may result.
 Use a ground fault circuit interrupter (GFCI) in any
damp or highly conductive area (such as metal
decking or steel work).
Never use worn, bare, frayed or otherwise damaged
electrical cords with the generator. Death, serious
injury, or property damage from electrical shock may
result.
Gasoline is highly FLAMMABLE and its vapors
are EXPLOSIVE. Never allow smoking, open
flames, sparks or heat in the vicinity while
handling gasoline. Avoid spilling gasoline on a
hot engine. Comply with all laws regulating storage
and handling of gasoline.
Do Not overfill the fuel tank. Always allow room for
fuel expansion. If tank is overfilled, fuel can
overflow onto a hot engine and cause a FIRE or
an EXPLOSION.
Never store a generator with fuel in the tank where
gasoline vapors might reach an open flame, spark or
pilot light (as on a furnace, water heater, clothes
dryer). FIRE or an EXPLOSION may result.
 The unit requires an adequate flow of cooling air for
its continued proper operation. Never operate the
unit inside any room or enclosure where the free
flow of cooling air into and out of the unit might be
obstructed. Allow at least 2 feet of clearance on all
sides of generator, or you could damage the unit.
Read Cold Weather Operation on page 8.
Never start or stop the unit with electrical loads
connected to receptacles and with the connected
devices turned ON. Start the engine and let it
stabilize before connecting any electrical loads.
Disconnect all electrical loads before shutting down
the generator.
Do Not insert any object through cooling slots of the
engine. You could damage the unit or injure yourself.
 Never operate the generator:
in rain; in any enclosed compartment; when
connected electrical devices overheat; if electrical
output is lost; if engine or generator sparks; if flame
or smoke is observed while unit is running; if unit
vibrates excessively.
GROUNDING THE
GENERATOR
The National Electrical Code requires that the frame
and external electrically conductive parts of this
generator be properly connected to an approved earth
ground. Local electrical codes may also require proper
grounding of the unit. For that purpose, a
GROUNDING WING NUT is provided on the
generator (Figure 1).
Generally, connecting a No. 12 AWG (American Wire
Gauge) stranded copper wire to the grounding wing
nut and to an earthdriven copper or brass grounding
rod (electrode) provides adequate protection against
electrical shock. Be careful to keep the grounding wire
attached to the generator when connecting the
stranded copper wire to the grounding rod. However,
local codes may vary widely. Consult with a local
electrician for grounding requirements in your area.
Properly grounding the generator helps prevent
electrical shock if a ground fault condition exists in the
generator or in connected electrical devices. Proper
grounding also helps dissipate static electricity, which
often builds up in ungrounded devices.
Figure 1 - Grounding Wing Nut
Grounding Wing Nut

Generac Portable Products 00XL Extended Life Generator
4
12 Volt DC, 10 Amp Receptacle  Recharge a
discharged 12 Volt automotive type battery through
this receptacle.
120 Volt AC, 15 Amp Receptacles  May be used to
supply electrical power for the operation of 120 Volt
AC, 1 Amp, single phase, 60 Hz electrical lighting,
appliance, tool and motor loads.
120 Volt AC, 30 Amp Locking Receptacle  May be
used to supply electrical power for the operation of
120 Volt AC, 30 Amp, single phase, 60 Hz electrical
lighting, appliance, tool and motor loads.
120/2 0 Volt AC, 30 Amp Locking Receptacle 
May be used to supply electrical power for the
operation of 120 and/or 240 Volt AC, 30 Amp, single
phase, 60 Hz electrical lighting, appliance, tool and
motor loads.
Air Cleaner  Uses a dry type filter element and
foam pre-cleaner to limit the amount of dirt and dust
sucked into the engine.
Choke Lever  Used when starting a cold engine.
Circuit Breakers (AC)  Each receptacle is provided
with a circuit breaker to protect the generator against
electrical overload. Breakers are "push to reset" type.
Fuel Tank  Capacity of seven (7) U.S. gallons.
Grounding Wing Nut  Used for proper grounding of
unit.
Idle Control Switch  With this switch set to ON,
printed circuit board in control panel automatically
reduces engine speed when no load is connected and
increases engine to proper speed when load is
applied. However, be sure switch is OFF when starting
engine.
Recoil Starter  Used for starting the engine.
Run/Stop Switch  Set this switch to "RUN" before
using recoil starter. Set switch to "STOP" to switch
OFF engine.
Spark Arrester Muffler  Exhaust muffler lowers
engine noise and is equipped with a spark arrester
screen.
KNOW YOUR GENERATOR
Read this owners manual and safety rules before operating your generator.
Compare the illustrations with your generator, to familiarize yourself with the locations of various controls and
adjustments. Save this manual for future reference.
Circuit Breakers (AC)
Spark Arrester Muffler
Idle Control Switch
Air Cleaner
Fuel Tank
Recoil Starter
120 Volt AC, 30 Amp
Receptacle
120/240 Volt AC,
30 Amp Receptacle
12 Volt DC, 10 Amp
Receptacle
Choke Lever
Run/Stop Switch
120 Volt AC, 1 Amp
Receptacles Grounding Wing Nut

Generac Portable Products 00XL Extended Life Generator
BEFORE STARTING THE
ENGINE
Add Oil
WARNING! Any attempt to crank or start the
engine before it has been properly filled with
the recommended oil may result in an engine
failure.
 Place generator on a level surface.
 Refer to your engine owners manual for proper oil
fill information.
NOTE: The generators revolving field rides on a
prelubricated and sealed ball bearing that requires no
additional lubrication for the life of the bearing.
Add Gasoline
DANGER! NEVER fill fuel tank indoors.
NEVER fill fuel tank when engine is running or
hot. Do Not light a cigarette or smoke when
filling the fuel tank.
WARNING! Do Not overfill the fuel tank.
Always allow room for fuel expansion.
 Use regular UNLEADED gasoline with unit. Do Not
use premium gasoline. Do Not mix oil with gasoline.
 Clean area around fuel fill cap, remove cap.
 Slowly add unleaded regular gasoline to fuel tank.
Be careful not to overfill. Allow about 1/2" tank space
for fuel expansion, as shown in Figure 2.
 Install fuel cap and wipe up any spilled gasoline.
IMPORTANT: It is important to prevent gum deposits
from forming in essential fuel system parts, such as
the carburetor, fuel filter, fuel hose or tank during
storage. Also, experience indicates that
alcoholblended fuels (called gasohol, ethanol or
methanol) can attract moisture, which leads to
separation and formation of acids during storage.
Acidic gas can damage the fuel system of an engine
while in storage.
To avoid engine problems, the fuel system should be
emptied before storage of 30 days or longer. See
Storage on page 11. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
Figure 2  Fuel Expansion Space

Generac Portable Products 00XL Extended Life Generator
6
OPERATING THE
GENERATOR
CAUTION! Never start or stop the unit with
electrical loads connected to the receptacles
AND with the connected devices turned ON.
Starting the Engine
DANGER! Never run engine indoors or in
enclosed poorly ventilated areas. Engine
exhaust contains carbon monoxide, an odorless
and deadly gas.
WARNING! Temperature of muffler and nearby
areas may exceed 1 0°F (6 °C). Avoid these
areas.
 Unplug all electrical loads from units receptacles
before starting the engine.
 Make sure the unit is in a level position.
 Open the fuel shutoff valve (Figure 3).
 Make sure the Idle Control switch is Off.
 Place the Run/Stop switch in the Run position.
 Place the choke lever in the Full choke position by
sliding it to the left toward the valve cover in the
direction indicated by the arrow (Figure 4).
 Grasp starter grip and pull slowly until you feel slight
resistance, then pull quickly. Do Not let handle
snap back into engine.
 When engine starts, move choke lever to Run
position by sliding it all the way to the right (away
from the valve cover and under the arrow).
NOTE: If engine fails to start after 3 pulls, move the
choke lever to Half choke position and pull starter
rope again 2 times.
NOTE: If the engine still fails to start, check for proper
oil level in crankcase. Unit is equipped with a low oil
shutdown system. See engine owners manual for
information regarding the low oil shutdown system.
Connecting Electrical Loads
 Let engine stabilize and warm up for a few minutes
after starting.
 Plug in and turn on the desired 120 and/or 240 Volt
AC, single phase, 60 Hertz electrical loads.
Do Not connect 240 Volt loads to the 120 Volt
receptacles.
Do Not connect 3-phase or 0 Hz loads to the
generator.
DO NOT OVERLOAD THE GENERATOR. See
Dont Overload the Generator on page 10.
Figure 3  Fuel Valve In Open Position
Full Choke
Position
Figure 4  Choke Lever

Generac Portable Products 00XL Extended Life Generator
7
Stopping the Engine
 Unplug all electrical loads from generator panel
receptacles. Never start or stop engine with
electrical devices plugged in and turned on.
 Put the Idle Control switch in the Off position.
 Let engine run at noload for 30 seconds to stabilize
the internal temperatures of engine and generator.
 Move Run/Stop switch to Stop position.
 Close the fuel shutoff valve.
Operating Automatic Idle Control
This switch is designed to greatly improve fuel
economy. When this switch is turned ON, the
engine will only run at its normal high governed engine
speed when an electrical load is connected. When the
electrical load is removed, the engine will run at a
reduced speed. With the switch Off, the engine will
run at a constant high engine speed. Always have
the switch Off when starting and stopping the
engine.
Battery Safety
DANGER! Storage batteries give off explosive
hydrogen gas while recharging. An explosive
mixture will remain around the battery for a long
time after it has been charged. The slightest
spark can ignite the hydrogen and cause an
explosion. Such an explosion can shatter the
battery and cause blindness or other serious
injury.
DANGER! Do Not permit smoking, open
flame, sparks, or any other source of heat
around a battery. Wear protective goggles,
rubber apron and rubber gloves when working
around a battery. Battery electrolyte fluid is an
extremely caustic sulfuric acid solution that can
cause severe burns. If spill occurs, flush area
with clear water immediately.
Charging a Battery
Your generator has the capability of recharging a
discharged 12 Volt automotive or utility style storage
battery. Do Not use the unit to charge any 6 Volt
batteries. Do Not use the unit to crank an engine
having a discharged battery.
To recharge 12 Volt batteries, proceed as follows:
 Check fluid level in all battery cells. If necessary,
add ONLY distilled water to cover separators in
battery cells. Do Not use tap water.
 If the battery is equipped with vent caps, make sure
they are installed and are tight.
 If necessary, clean battery terminals.
 Connect battery charge cable connector plug to
panel receptacle identified by the words
12-VOLTS D.C.
 Connect battery charge cable clamp with red handle
to the positive (+) battery terminal (Figure ).
 Connect battery charge cable clamp with black
handle to the negative () battery terminal
(Figure ).
 Start engine. Let the engine run while battery
recharges.
 When battery has charged, shut down engine.
NOTE: Use an automotive hydrometer to test battery
state of charge and condition. Follow the hydrometer
manufacturers instructions carefully. Generally, a
battery is considered to be at 100% state of charge
when specific gravity of its fluid (as measured by
hydrometer) is 1.260 or higher.
Figure  Connect Battery Cable
Red Black

Generac Portable Products 00XL Extended Life Generator
8
COLD WEATHER
OPERATION
Under certain weather conditions (temperatures below
40°F [4°C] and a high dew point), your generator may
experience icing of the carburetor and/or the
crankcase breather system.
In an emergency, use the original shipping box as a
temporary shelter:
 Cut off all flaps.
 Cut out one of the long sides of the box to expose
exhaust side of unit. Ensure a minimum of two feet
clearance between open side of box and nearest
object.
 Cut appropriate slots to access receptacles and
clear handles of unit.
 Start unit, then place box over it.
IMPORTANT: Remove shelter when temperature is
above 40°F [4°C].
For a more permanent shelter, build a structure that
will enclose three sides and the top of the generator:
 Make sure entire muffler-side of generator is
exposed as shown in Figure 6. Note that your
generator may appear different from that shown
here.
 Ensure a minimum of two feet clearance between
open side of box and nearest object.
 Face exposed end away from wind and elements.
 Enclosure should hold enough heat created by the
generator to prevent problems.
CAUTION! NEVER run unit indoors. Do Not
enclose generator any more than shown.
Remove shelter when temperatures are above
40°F [4°C].
CORD SETS/RECEPTACLES
This generator is equipped with the following
receptacles:
120 Volt AC, 15 Amp Receptacle
This outlet is protected against overload by a 1 Amp
push-to-reset circuit breaker (Figure 7).
Use each socket to operate 120 Volt AC, single phase
60 Hz electrical loads requiring up to 1,800 watts
(1.8 kW) at 1 Amps. Use cord sets that are rated for
12 Volts at 1 Amps (or greater).
Wind
Figure 6  Temporary Cold Weather Shelter
Figure 7  120 Volt AC, 1 Amp Receptacles

Generac Portable Products 00XL Extended Life Generator
9
120 Volt AC, 30 Amp Locking
Receptacle
Use a NEMA L 30 plug with this receptacle. Connect
a 3wire cord set rated for 12 Volts AC at 30 Amps to
the plug (Figure 8).
Use this receptacle to operate 120 Volt AC, 60 Hz,
single phase loads requiring up to 3,600 watts
(3.6 kW) of power at 30 Amps. The outlet is protected
by a 30 Amp pushtoreset circuit breaker.
120/2 0 Volt AC, 30 Amp Locking
Receptacle
Use a NEMA L1430 plug with this receptacle.
Connect a 4wire cord set rated for 2 0 Volt AC loads
at 30 Amps (or greater). You can use the same 4wire
cord if you plan to run a 120 Volt load (Figure 9).
This receptacle powers 120/240 Volt AC, single phase,
60 Hz loads requiring up to 3,600 watts (3.6 kW) at
30 Amps for 120 Volts; , 00 watts of power ( . kW)
at 22.9 Amps for 240 Volts. This outlet is protected by
30 Amp pushtoreset circuit breakers.
Figure 9  120/240 Volt, 30 Amp Receptacle
Figure 8 - 120 Volt, 30 Amp Receptacle

Generac Portable Products 00XL Extended Life Generator
10
DONT OVERLOAD THE
GENERATOR
Overloading a generator in excess of its rated wattage
capacity can result in damage to the generator and/or
connected electrical devices. Observe the following to
prevent overloading the unit:
 Add up the total wattage of all electrical devices to
be connected at one time. This total should NOT be
greater than the generators wattage capacity.
 The rated wattage of lights can be taken from light
bulbs. The rated wattage of tools, appliances and
motors can usually be found on a data plate or decal
affixed to the device.
 If the appliance, tool or motor does not give wattage,
multiply 120 Volts times ampere rating to determine
watts (volts x amps = watts).
 Some electric motors, such as induction types,
require about three times more watts of power for
starting than for running. This surge of power lasts
for only a few seconds when starting such motors.
Be sure you allow for this high starting wattage
when selecting electrical devices to connect to your
generator. First figure the watts needed to start the
largest motor. Add to that figure the running watts of
all other connected loads.
 Items in the wattage reference guide (Figure 10) are
provided to help you to determine how many items
the generator can operate at one time.
Recreational/Home Uses
Tool/Appliance...................................................Watts
AM/FM clock radio.................................................... 0
Light bulb................................................................100
Fan .........................................................................200
20" color TV............................................................400
*Deep freezer ......................................................... 00
Personal computer and 1 " monitor .......................800
*1/3 hp furnace fan blower......................................800
Microwave oven......................................................800
*18 cu ft refrigerator................................................800
Sump pump ..........................................................1000
Electric skillet........................................................12 0
*½ hp water well pump .........................................1400
*12,000 Btu window air conditioner ......................1400
Space heater ........................................................1800
Electric water heater.............................................4000
Professional/Contractor Uses
Tool/Appliance...................................................Watts
*1/3 hp airless sprayer............................................600
3/8" hammer drill.....................................................600
Variable speed Sawzall®........................................960
½" power drill........................................................1000
Quartz-halogen work light.....................................1000
Belt sander ...........................................................1200
7 ¼" circular saw ..................................................1 00
7 ¼" worm drive saw ............................................1600
*1½ hp air compressor .........................................1800
*10" power miter saw............................................1800
6" bench grinder ...................................................1800
*6" table planer .....................................................1800
*10" table/radial arm saw......................................2000
Wire feed welder...................................................2400
* allow 3 times listed watts for starting this device
Figure 10  Wattage Reference Guide

Generac Portable Products 00XL Extended Life Generator
11
GENERAL MAINTENANCE
RECOMMENDATIONS
The owner/operator is responsible for making sure that
all periodic maintenance tasks are completed on a
timely basis; that all discrepancies are corrected; and
that the unit is kept clean and properly stored.
Never operate a damaged or defective generator.
Engine Maintenance
See engine owners manual for instructions.
Generator Maintenance
Generator maintenance consists of keeping the unit
clean and dry. Operate and store the unit in a clean
dry environment where it will not be exposed to
excessive dust, dirt, moisture or any corrosive vapors.
Cooling air slots in the generator must not become
clogged with snow, leaves or any other foreign
material.
NOTE: Do Not use a garden hose to clean generator.
Water can enter engine fuel system and cause
problems. In addition, if water enters generator
through cooling air slots, some of the water will be
retained in voids and cracks of the rotor and stator
winding insulation. Water and dirt buildup on the
generator internal windings will eventually decrease
the insulation resistance of these windings.
To Clean the Generator
 Use a damp cloth to wipe exterior surfaces clean.
 A soft bristle brush may be used to loosen caked on
dirt or oil.
 A vacuum cleaner may be used to pick up loose dirt
and debris.
 Low pressure air (not to exceed 2 psi) may be
used to blow away dirt. Inspect cooling air slots and
opening on generator. These openings must be kept
clean and unobstructed.
STORAGE
The generator should be started at least once every
seven days and allowed to run at least 30 minutes. If
this cannot be done and you must store the unit for
more than 30 days, use the following guidelines to
prepare it for storage.
Generator Storage
 Clean the generator as outlined in To Clean the
Generator.
 Check that cooling air slots and openings on
generator are open and unobstructed.
DANGER! Storage covers can be flammable.
Do Not place a storage cover over a hot
generator. Let the unit cool for a sufficient time
before placing a cover on the unit.
Engine Storage
See engine owners manual for instructions.
Other Storage Tips
Do Not store gasoline from one season to another.
 Replace the gasoline can if it starts to rust. Rust
and/or dirt in a gasoline can cause problems when
you use that fuel with this unit.
 Store unit in a clean and dry area.
SPECIFICATIONS
Maximum Surge Watts . . . . . . . . . . . . .6,87 watts
Continuous Wattage Capacity . . . . . . . , 00 watts
Power Factor . . . . . . . . . . . . . . . . . . . . . . . . . .1.0
Rated Maximum Continuous Load Current
At 120 Volts . . . . . . . . . . . . . . . . . . .4 .8 Amps
At 240 Volts . . . . . . . . . . . . . . . . . . .22.9 Amps
Phase . . . . . . . . . . . . . . . . . . . . . . . . . . .1phase
Rated Frequency . . . . . . . . . . . . . . . . . . .60 Hertz
Fuel Tank Capacity . . . . . . . . . . . . . 7 U.S. gallons

Generac Portable Products 00XL Extended Life Generator
12
Problem Cause Correction
Engine is running, but no
AC output is available.
1. Circuit breakers is open.
2. Poor connection or defective cord
set.
3. Connected device is bad.
4. Fault in generator.
1. Reset circuit breaker.
2. Check and repair.
3. Connect another device that is in
good condition.
4. Contact Generac service facility.
Engine runs good at no-
load but bogs down"
when loads are
connected.
1. Short circuit in a connected load.
2. Generator is overloaded.
3. Engine speed is too slow.
4. Shorted generator circuit.
1. Disconnect shorted electrical load.
2. See Don't Overload the Generator,
page 10.
3. Contact Generac service facility.
4. Contact Generac service facility.
Engine will not start; or
starts and runs rough.
1. Run/Stop Switch set to STOP.
2. Dirty air cleaner.
3. Out of gasoline.
4. Stale gasoline.
. Spark plug wire not connected to
spark plug.
6. Bad spark plug.
7. Water in gasoline.
8. Overchoking.
9. Low oil level.
10. Excessively rich fuel mixture.
11. Intake valve stuck open or closed.
12. Engine has lost compression.
1. Set switch to RUN.
2. Clean or replace air cleaner.
3. Fill fuel tank.
4. Drain gas tank; fill with fresh fuel.
. Connect wire to spark plug.
6. Replace spark plug.
7. Drain gas tank; fill with fresh fuel.
8. Open choke fully and crank engine.
9. Fill crankcase to proper level.
10. Contact Generac service facility.
11. Contact Generac service facility.
12. Contact Generac service facility.
Engine shuts down
during operation
1. Out of gasoline.
2. Low oil level.
3. Fault in engine.
1. Fill fuel tank.
2. Fill crankcase to proper level.
3. Contact Generac service facility.
Engine lacks power.
1. Load is too high.
2. Dirty air filter.
3. Engine needs to be serviced.
1. See Don't Overload the Generator,
page 10.
2. Replace air filter.
3. Contact Generac service facility.
Engine hunts or falters.
1. Choke is opened too soon.
2. Carburetor is running too rich or
too lean.
1. Move choke to halfway position until
engine runs smoothly.
2. Contact Generac service facility.
TROUBLESHOOTING

Generac Portable Products 00XL Extended Life Generator
13
Item Part # Qty Description
1 A92070 1 Control Panel
2 23897 4 #10 (M ) Flat Washer
3 49226 4 M Lock Washer
4 91 26 4 M -0.8 x 12mm Screw
82 38 1 Idle Control Switch
6 82881 4 7/16" Lock Washer
7 43181 4 M3-0. x 10mm Screw
8 43182 4 M3 Lock Washer
9 90418 1 12V DC Outlet
10 7 207A 2 30A Circuit Breaker
11 7 207D 2 1 A Circuit Breaker
12 2336 6 #8 Shakeproof Washer
13 68868 1 120 Volt AC, 30 Amp Locking
Outlet
Item Part # Qty Description
14 43437 1 120V/240V AC, 30A Locking
Outlet
1 6302 1 120V AC, 1 A Duplex Outlet
16 43180 6 M4 Flat Washer
17 22264 6 #8 (M4) Lock Washer
18 171 6 M4-0.7 Hex Nut
19 64 26 8 #6-32 x 3/8" Screw
20 83970 1 System Control Board
21 64 2 4 3/4" Hex Stand-Off
22 87962 1 12V, 10A Cir. Breaker (auto)
23 8433 1 Wire Harness Assembly
24 84134 1 Rubber Conn. Grommet
2 B92069 1 Box, Control Panel
26 84028 1 Idle Control Transformer
EXPLODED VIEW AND PARTS LIST  CONTROL PANEL

Generac Portable Products 00XL Extended Life Generator
14
ELECTRICAL SCHEMATIC

Generac Portable Products 00XL Extended Life Generator
1
WIRING DIAGRAM

Generac Portable Products 00XL Extended Life Generator
16
EXPLODED VIEW  UNIT

Generac Portable Products 00XL Extended Life Generator
17
Item Part # Qty. Description
1 A92432 1 CRADLE
2 A92 31 1 SUPPORT, Engine
3 A92731 1 SUPPORT, Engine & Muffler
4 92247 1 HOUSING, Engine Adapter
92678G 1 ASSEMBLY, Rotor
6 92680G 1 ASSEMBLY, Stator
7 6 791 1 BEARING
8 674 1 1 WASHER, M8 Flat
9 22129 14 WASHER, M8 Lock
10 86307 4 HHMS, /16-24 x 3/4 SEMS
11 28092 1 HHCS, /16-24 x 9-1/4"
12 92609 2 MOUNT, Vibration
13 828 7 4 MOUNT, Vibration
14 40976 2 SCREW, M8 - 1.2 x 20
1 66476 2 CAPSCREW, M6 - 1.0 x
12mm
16 92 32 1 BRACKET, Muffler
17 22142 2 SCREW, /16 - 18 x 3/4"
18 A7433 1 MUFFLER
19 90239 1 GASKET, Muffler
20 81917 1 PIN, 4mm x 10 Roll
21 B4986 1 DECAL, Ground
22 83083 1 SCREEN, Spark Arrester
2 6682 C 1 CARRIER, Rear Bearing
26 74908 4 SCREW, M -0.8 x 10 Taptite
27 86308A 4 BOLT, M6-1 x 16 mm Stator
28 6 79 1 RECTIFIER, Battery Charge
29 66849A 1 SCREW, M -0.8 x 20 Taptite
30 67022 1 GROMMET, Rubber
31 84132 1 ASSEMBLY, Drive Module,
Power Regulator
32 66386 1 ASSEMBLY, Brush Holder
33 66849 2 SCREW, M - 0.8 x 16 Taptite
34 B4871 1 COVER, Bearing Carrier
3 22769 1 WASHER, #10 Shakeproof
Int.
36 86494 1 SCREW, M6 -1.0 x 16 Wing
37 86292 7 HHCS, -#10 Self Driller
38 7739 4 NUT, M6 Flange Lock
39 8346 4 GROMMET, Tank
40 70 8 4 HHCS, M6-1.0 x
Item Part # Qty. Description
41 80270 1 VALVE, Tank
42 78299 1 BUSHING, Plastic Tank
43 B4363 1 CAP, Fuel Gauge
44 B169 1 TANK, Fuel 7-Gal
4 B92039 1 SHIELD, Heat
46 9266 1 INSULATION, #2-1/4" Thick
47 8 000 1 CLIP, Insulation
48 143 3621 1 WIRE, Ground
49 268 0 2 WASHER, M6 Shakeproof
1 94479 1 DECAL, Danger (French &
English)
2 92611 2 DECAL, Heat Shield
2 244 12 NUT, /16 - 18 Hex
7 92639 1 DECAL, Control Panel
8 96198 1 ASSEMBLY, Control Box
9 NSP 1 ENGINE
60 22 31 2 HHCS, /16-18 x 1-3/4"
61 22473 4 WASHER, Flat M6
62 94480 1 DECAL, Start Instructions
(French & English)
63 2 717 1 DECAL, CSA
64 74728 1 DECAL, Grounded Neutral
6 76247 1 DECAL, Grounded Neutral
(French & English)
66 B96068 1 HEAT SHIELD, Muffler
67 6893 CRIMPTITE, 10-24 x 1/2"
68 78817 1 DECAL, Data Sheet
Items Not Illustrated
6 787 1 Battery Charge Cable
37806 1 120 Volt 30 Amp Locking Plug
43438 1 120/240 Volt 30 Amp Locking
Plug
B2674 1 Generator Owners Manual
A8927 1 Engine Owners Manual
73111 1 Air Filter
72347 1 Spark Plug
84882 1 Spark Plug Wrench Drive
Optional Accessories Not Included
Model 1002 Wheel Kit
PARTS LIST  UNIT

LIMITED WARRANTY
FOR "GN" ENGINE DRIVEN PORTABLE GENERATORS
GENERAC PORTABLE PRODUCTS (hereafter referred to as the COMPANY) warrants to the original purchaser
that the alternator and control panel for its portable generator will be free from defects in materials or
workmanship for the items and period set forth below from the date of original purchase. This warranty is not
transferable and applies only to portable generators driven by a GN-Series engine.
Consumer* Commercial*
Alternator 2 years (2nd year parts only) 1 year
Engine Warranted solely by the engine manufacturer
With the exception of European Community Countries, all units bound for export shall be warranted for
One (1) Year in Consumer applications, and 9 days in Commercial applications as defined below.
*NOTE: For the purpose of this warranty "consumer use" means personal residential household use by
original purchaser. This warranty does not apply to units used for Prime Power in place of utility.
"Commercial Use" means all other uses, including rental, construction, commercial and income
producing purposes. Once a generator has experienced commercial use, it shall thereafter be considered
a commercial use generator for the purposes of this warranty.
During said warranty period, the COMPANY will, at is option, repair or replace any part which, upon examination
by the COMPANY, is found to be defective under normal use and service**. Starting batteries are not warranted
by the COMPANY. All transportation costs under warranty, including return to the factory if necessary, are to be
borne by the purchaser and prepaid by the purchaser. This warranty does not cover normal maintenance and
service and does not apply to a generator set, alternator, or parts which have been subjected to improper or
unauthorized installation or alteration, misuse, negligence, accident, overloading, overspeeding, improper
maintenance, repair or storage so as, in the COMPANYs judgement, to adversely affect its performance and
reliability.
**NORMAL WEAR: As with all mechanical devices, the generator need periodic parts service and
replacement to perform well. This warranty will not cover repair when normal use has exhausted the life
of a part or generator.
THERE IS NO OTHER EXPRESS WARRANTY. THE COMPANY HEREBY DISCLAIMS ANY AND
ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THOSE OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE TO THE EXTENT PERMITTED BY LAW. THE
DURATION OF ANY IMPLIED WARRANTIES WHICH CANNOT BE DISCLAIMED IS LIMITED TO
THE TIME PERIOD AS SPECIFIED IN THE EXPRESS WARRANTY. LIABILITY FOR
CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES UNDER ANY AND ALL WARRANTIES
IS EXCLUDED. THE COMPANY ALSO DISCLAIMS ANY RESPONSIBILITY FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SUCH AS THE LOSS OF TIME OR THE USE OF THE POWER
EQUIPMENT, OR ANY COMMERCIAL LOSS DUE TO THE FAILURE OF THE EQUIPMENT: AND
ANY IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of
incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty
gives you specific legal rights and you may also have other rights, which vary from state to state.
For service, see your nearest COMPANY authorized warranty service facility or call 1-877- 44-0982. Warranty
service can be performed only by a COMPANY authorized service facility. This warranty will not apply to service at
any other facility. At the time of requesting warranty service, evidence of original purchase date must be
presented.
GENERAC PORTABLE PRODUCTS
Jefferson, Wisconsin 535 9