Generac Power Systems D3.4L G16 Extended Tank Instruction sheet

Installation Guidelines
Stationary Diesel Generators
Residential and Commercial
15–50 kW, 12–50 kVa
SAVE THIS MANUAL FOR FUTURE REFERENCE
Para español , visita: http://www.generac.com/service-support/product-support-lookup
Pour le français, visiter : http://www.generac.com/service-support/product-support-lookup
®
Register your Generac product at:
WWW.GENERAC.COM
1-888-GENERAC
(888-436-3722)
(000209b)
WARNING
Loss of life. This product is not intended to
be used in a critical life support application.
Failure to adhere to this warning could result
in death or serious injury.

ii Installation Guidelines For Protector Diesel Generators
Use this page to record important information about this generator.
Record the information found on this unit data label on this
page. For location of the unit data label, see owner’s manual.
The unit has a label plate affixed to the inside partition, to the
left of the control panel console.
Always supply the complete model number and serial num-
ber of the unit when contacting an Independent Authorized
Service Dealer (IASD) about parts and service.
Operation and Maintenance: Correct maintenance and
care of the generator ensures a minimum number of prob-
lems and keeps operating expenses at a minimum. It is the
operator’s responsibility to perform all safety checks, to ver-
ify that all maintenance for safe operation is performed
promptly, and to have the equipment inspected periodically
by an IASD. Normal maintenance, service, and replacement
of parts are the responsibility of the owner/operator and, as
such, are not considered defects in materials or workman-
ship within the terms of the warranty. Individual operating
habits and usage may contribute to the need for additional
maintenance or service.
When the generator requires servicing or repairs, Generac
recommends contacting an IASD for assistance. Authorized
service technicians are factory-trained and are capable of
handling all service needs. To locate the nearest IASD,
please visit the dealer locator at:
www.generac.com/Service/DealerLocator/.
Model:
Serial:
Prod Date Week:
Volts:
LPV Amps:
NG Amps:
Hz:
Phase:
Controller P/N:
(000394)
WARNING
Breathing diesel engine exhaust exposes you
to chemicals known to the State of California
to cause cancer and birth defects or other
reproductive harm.
• Always start and operate the engine in a
well-ventilated area.
• If in an enclosed area, vent the exhaust to
the outside.
• Do not modify or tamper with the exhaust
system.
• Do not idle the engine except as necessary.
For more information go to
www.P65Warnings.ca.gov/diesel.

Installation Guidelines for Protector Diesel Generators iii
Table of Contents
Section 1: Safety Rules & General
Information
Introduction ..........................................................1
Read This Manual Thoroughly ....................................1
Safety Rules .........................................................1
How to Obtain Service .................................................1
General Hazards ..................................................2
Exhaust Hazards ..................................................3
Electrical Hazards ................................................3
Fire Hazards .........................................................3
Explosion Hazards ...............................................4
Lifting Hazards .....................................................4
General Rules .......................................................4
Before You Begin ........................................................5
Standards Index ..........................................................5
Section 2: Installation Planning
Protector Diesel Installation
Planning Checklist ...............................................7
Safety Accessories ..............................................8
Unit Drawings .......................................................9
Installation Drawings ...................................................9
Wiring Diagrams ..........................................................9
Receiving ............................................................10
Receiving and Unpacking ..........................................10
Inspection ..................................................................10
Storage Before Installation ...............................10
Long Term Storage ...................................................10
Short Term Storage ...................................................10
Lifting ..................................................................10
Generator Location ............................................11
General Location Guidelines .....................................11
Weather Considerations ............................................11
Product Accessories .........................................11
Section 3: Site Selection and Preparation
Site Selection .....................................................13
Installation Guidelines for Stationary Fuel
Storage Tanks ...........................................................13
Site Preparation .................................................14
Generator Foundation ...............................................14
Concrete Pad ............................................................14
Dimensions ................................................................14
Unit Clearance ...........................................................14
Stub-Up Area .............................................................14
Mounting ............................................................15
Fixed Foundation .......................................................15
Connections ..............................................................15
Combustible Floor and Roof Protection ....................15
Section 4: Diesel Fuel Systems
General Information ..........................................17
Diesel Fuel Base Tank ....................................... 17
Diesel Fuel Recommendations ........................17
Fuel Maintenance ..............................................17
Section 5: Electrical System
General Information ..........................................19
Connecting Generator Feeder Conductors .....19
Connecting Start Circuit Wires ........................19
Remove Rear Panel and Stub-Up Cover .........20
Typical Load Leads and Control
Wiring in Stub-Up ..............................................20
Customer Load Wiring ......................................20
Control Wiring Connections .............................22
RTS Series Transfer Switch With T1
Fuse/Connection .......................................................22
RTS Series Transfer Switch Without T1
Fuse/Connection .......................................................22
Two-Wire Start ..........................................................22
Optional Accessory Power ...............................24
Installing Stub-Up Cover and Rear Panel ........24
Transfer Switch Location .................................. 24
Battery ................................................................24
General Safety Precautions ......................................24
Battery Requirements ................................................25
Battery Installation .....................................................25

iv Installation Guidelines for Protector Diesel Generators
Section 6: Operational Checks
Introduction ........................................................27
Self Test ..............................................................27
Checking Manual Transfer Switch
Operation ............................................................27
Electrical Checks ...................................................... 27
Testing Generator Under Load .........................28
Testing Auxiliary Shutdown Switch
Operation ............................................................28
Checking Automatic Operation ........................29
Installation Summary ........................................29
Shutting Generator Down While Under
Load or During a Utility Outage ........................29
Section 7: Installation Checklists
Safety Checklist .................................................31
Installation Planning Checklist .........................31
Foundations and Mounting Checklist ..............31
Ventilation System Checklist ............................31
Exhaust System Checklist ................................32
Fuel System Checklist .......................................32
Electrical System Checklist ..............................32
Section 8: Installation Drawings
D2.5L G2 Single Wall
(10000022175, page 1 of 2) ................................33
D2.5L G2 Single Wall
(10000022175, page 2 of 2) ................................34
D2.5L G2 Extended Tank
(10000018189, page 1 of 2) ................................35
D2.5L G2 Extended Tank
(10000018189, page 2 of 2) ................................36
D2.5L G2–95 Gal Tank
(10000028999, page 1 of 2) ................................37
D2.5L G2–95 Gal Tank
(10000028999, page 2 of 2) ................................38
D2.2L G22 Single Wall
(10000018294, page 1 of 2) ................................39
D2.2L G22 Single Wall
(10000018294, page 2 of 2) ................................40
D2.2L G22 Extended Tank
(10000018412, page 1 of 2) ............................... 41
D2.2L G22 Extended Tank
(10000018412, page 2 of 2) ............................... 42
D2.2L G22–132 Gal Tank
(10000029492, page 1 of 2) ............................... 43
D2.2L G22–132 Gal Tank
(10000029492, page 2 of 2) ............................... 44
D3.4L G16 Single Wall
(10000042752, page 1 of 2) ............................... 45
D3.4L G16 Single Wall
(10000042752, page 2 of 2) ............................... 46
D3.4L G16 Extended Tank
(10000042807, page 1 of 2) ............................... 47
D3.4L G16 Extended Tank
(10000042807, page 2 of 2) ............................... 48
D3.4L G16 – 132 Gal Tank
(10000043316, page 1 of 2) ............................... 49
D3.4L G16 – 132 Gal Tank
(10000043316, page 2 of 2) ............................... 50
Alternator Wiring Diagram (1 of 2) ................... 51
Alternator Wiring Diagram (2 of 2) ................... 52
Alternator AC Lead Connections ..................... 53
Four-Lead, Single-Phase Stator ............................... 53
Alternator Power Winding Connections ......... 53
Three-Phase Alternators (“Y” Configuration) ............ 53
Three-Phase Alternators (“Delta” Configuration) ...... 54

Safety Rules & General Information
Installation Guidelines for Protector Diesel Generators 1
Section 1: Safety Rules & General Information
Introduction
Thank you for purchasing this high performance, liquid-
cooled, engine-driven stationary generator. It is designed
to automatically supply electrical power to operate critical
loads during a utility power failure.
The engine and generator are factory installed in an all-
weather, metal enclosure intended exclusively for out-
door installation. The engine operates on ultra low sulfur
diesel fuel.
NOTE: This generator is suitable for supplying typical
residential and commercial loads such as induction
motors (sump pumps, refrigerators, air conditioners, fur-
naces, etc.), electronic components (computer, monitor,
TV, etc.), lighting loads, and microwaves, when sized cor-
rectly.
The information in this manual is accurate based on
products produced at the time of publication. The manu-
facturer reserves the right to make technical updates,
corrections, and product revisions at any time without
notice.
Read This Manual Thoroughly
If any section of this manual is not understood, contact
the nearest Independent Authorized Service Dealer
(IASD) or Generac Customer Service at 1-888-436-3722
(1-888-GENERAC), or visit www.generac.com for start-
ing, operating, and servicing procedures. The owner is
responsible for correct maintenance and safe use of the
unit.
This manual must be used in conjunction with all other
supporting product documentation supplied with the
product.
SAVE THESE INSTRUCTIONS for future reference. This
manual contains important instructions that must be fol-
lowed during placement, operation, and maintenance of
the unit and its components. Always supply this manual
to any individual that will use this unit, and instruct them
on how to correctly start, operate, and stop the unit in
case of emergency.
Safety Rules
The manufacturer cannot anticipate every possible cir-
cumstance that might involve a hazard. The alerts in this
manual, and on tags and decals affixed to the unit, are
not all inclusive. If using a procedure, work method, or
operating technique that the manufacturer does not spe-
cifically recommend, verify that it is safe for others and
does not render the equipment unsafe.
Throughout this publication, and on tags and decals
affixed to the unit, DANGER, WARNING, CAUTION, and
NOTE blocks are used to alert personnel to special
instructions about a particular operation that may be haz-
ardous if performed incorrectly or carelessly. Observe
them carefully. Alert definitions are as follows:
NOTE: Notes contain additional information important to
a procedure and will be found within the regular text of
this manual.
These safety alerts cannot eliminate the hazards that
they indicate. Common sense and strict compliance with
the special instructions while performing the action or
service are essential to preventing accidents.
How to Obtain Service
When the unit requires servicing or repairs, contact Gen-
erac Customer Service at 1-888-GENERAC (1-888-436-
3722) or visit www.generac.com for assistance.
When contacting Generac Customer Service about parts
and service, always supply the complete model and
serial number of the unit as given on its data decal
located on the unit. Record the model and serial numbers
in the spaces provided on the front cover of this manual.
(000100a)
WARNING
Consult Manual. Read and understand manual
completely before using product. Failure to
completely understand manual and product
could result in death or serious injury.
(000001)
DANGER
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
(000002)
WARNING
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
(000003)
CAUTION
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.

Safety Rules & General Information
2 Installation Guidelines for Protector Diesel Generators
General Hazards
(000190)
DANGER
Loss of life. Property damage. Installation must always
comply with applicable codes, standards, laws and
regulations. Failure to do so will result in death
or serious injury.
Automatic start-up. Disconnect utility power and
render unit inoperable before working on unit.
Failure to do so will result in death or serious injury.
(000191)
DANGER
(000209b)
WARNING
Loss of life. This product is not intended to
be used in a critical life support application.
Failure to adhere to this warning could result
in death or serious injury.
WARNING
Equipment damage. This unit is not intended for use as a
prime power source. It is intended for use as an intermediate
power supply in the event of temporary power outage only.
Doing so could result in death, serious injury, and
equipment damage. (000247a)
(000187)
WARNING
Electrocution. Potentially lethal voltages are generated
by this equipment. Render the equipment safe before
attempting repairs or maintenance. Failure to do so
could result in death or serious injury.
(000130)
WARNING
Accidental Start-up. Disconnect the negative battery
cable, then the positive battery cable when working
on unit. Failure to do so could result in death
or serious injury.
(000182a)
WARNING
Equipment damage. Only qualified service personnel may
install, operate, and maintain this equipment. Failure to follow
proper installation requirements could result in death, serious
injury, and equipment or property damage.
(000155a)
WARNING
Electric shock. Only a trained and licensed electrician
should perform wiring and connections to unit. Failure
to follow proper installation requirements could result in
death, serious injury, and equipment or property damage.
(000115)
WARNING
Moving Parts. Do not wear jewelry when
starting or operating this product. Wearing
jewelry while starting or operating this product
could result in death or serious injury.
(000111)
WARNING
Moving Parts. Keep clothing, hair, and
appendages away from moving parts. Failure
to do so could result in death or serious injury.
(000108)
WARNING
Hot Surfaces. When operating machine, do not
touch hot surfaces. Keep machine away from
combustibles during use. Hot surfaces could
result in severe burns or fire.
(000146)
WARNING
Equipment and property damage. Do not alter
construction of, installation, or block ventilation for
generator. Failure to do so could result in unsafe
operation or damage to the generator.
WARNING
Risk of injury. Do not operate or service this machine
if not fully alert. Fatigue can impair the ability to service
this equipment and could result in death or serious
injury. (000215)
WARNING
Injury and equipment damage. Do not use generator
as a step. Doing so could result in falling, damaged
parts, unsafe equipment operation, and could result
in death or serious injury. (000216)

Safety Rules & General Information
Installation Guidelines for Protector Diesel Generators 3
Exhaust Hazards
•Generator must be installed and operated outdoors
only.
Electrical Hazards
Fire Hazards
Asphyxiation. Running engines produce
carbon monoxide, a colorless, odorless,
poisonous gas. Carbon monoxide, if not
avoided, will result in death or serious injury.
(000103)
DANGER
(000178a)
Asphyxiation. Always use a battery operated carbon
monoxide alarm indoors and installed according to
the manufacturer’s instructions. Failure to do so
could result in death or serious injury.
WARNING
(000146)
WARNING
Equipment and property damage. Do not alter
construction of, installation, or block ventilation for
generator. Failure to do so could result in unsafe
operation or damage to the generator.
(000144)
DANGER
Electrocution. Contact with bare wires,
terminals, and connections while generator
is running will result in death or serious injury.
(000150)
DANGER
Electrocution. Never connect this unit to the electrical
system of any building unless a licensed electrician
has installed an approved transfer switch. Failure to
do so will result in death or serious injury.
(000237)
DANGER
Electrical backfeed. Use only approved switchgear to
isolate generator from the normal power source.
Failure to do so will result in death, serious injury,
and equipment damage.
(000152)
DANGER
Electrocution. Verify electrical system is
properly grounded before applying power.
Failure to do so will result in death or serious
injury.
(000188)
DANGER
Electrocution. Do not wear jewelry while
working on this equipment. Doing so will
result in death or serious injury.
(000104)
DANGER
Electrocution. Water contact with a power
source, if not avoided, will result in death
or serious injury.
(000145)
DANGER
Electrocution. In the event of electrical accident,
immediately shut power OFF. Use non-conductive
implements to free victim from live conductor. Apply
first aid and get medical help. Failure to do so will
result in death or serious injury.
WARNING
Fire hazard. Do not obstruct cooling and
ventilating airflow around the generator. Inadequate
ventilation could result in fire hazard, possible
equipment damage, death or serious injury. (000217)
WARNING
Fire and explosion. Installation must comply
with all local, state, and national electrical
(000218)
building codes. Noncompliance could result in unsafe
operation, equipment damage, death or serious injury.
WARNING
Fire hazard. Use only fully-charged fire
(000219)
extinguishers rated “ABC” by the NFPA. Discharged or
improperly rated fire extinguishers will not extinguish
electrical fires in automatic standby generators.
WARNING
to use required safety equipment could result
in death or serious injury. (000257)
Electrocution. Refer to local codes and
standards for safety equipment required when
working with a live electrical system. Failure

Safety Rules & General Information
4 Installation Guidelines for Protector Diesel Generators
Comply with regulations the Occupational Safety and
Health Administration (OSHA) has established, or with
equivalent standards. Also, verify that the unit is applied,
used, and maintained in accordance with the manufac-
turer's instructions and recommendations. Do nothing
that might alter safe application/usage and render the
unit in noncompliance with the aforementioned codes,
standards, laws, and regulations.
Explosion Hazards
Lifting Hazards
General Rules
(000147)
WARNING
Risk of Fire. Unit must be positioned in a
manner that prevents combustible material
accumulation underneath. Failure to do so
could result in death or serious injury.
(000192)
DANGER
Explosion and fire. Fuel and vapors are extremely
flammable and explosive. No leakage of fuel is
permitted. Keep fire and spark away. Failure to do
so will result in death or serious injury.
(000151a)
DANGER
Explosion and fire. Connection of fuel source must be
completed by a qualified professional technician or
contractor. Incorrect installation of this unit will result in
death, serious injury, and property and equipment damage.
(000174)
DANGER
Risk of fire. Allow fuel spills to completely dry
before starting engine. Failure to do so will
result in death or serious injury.
(000110)
WARNING
Risk of Fire. Hot surfaces could ignite
combustibles, resulting in fire. Fire could
result in death or serious injury.
DANGER
(000245)
Risk of electrocution. Avoid touching overhead
power lines when lifting or hoisting generator.
Failure to do so will result in death or serious
injury.
WARNING
Personal injury. Excessive weight. Use only
appropriate lifting eyes and lifting equipment to
lift unit. Improper lifting techniques could result in
equipment damage, death or serious injury. (000224)
WARNING
Personal injury. Failure to properly connect
lifting cables, chains, or straps could result in
death, serious injury, or property damage.
(000346)
WARNING
Personal Injury. Do not use lifting hook if there are
signs of damage or corrosion. Doing so could result
in death, serious injury, or property damage.
(000349)
WARNING
Personal Injury. Do not use lifting eye if there are signs
of damage or corrosion. Doing socould result in death,
serious injury, or property damage.
(000433)
WARNING
Personal Injury. Verify all fasteners are properly
tightened prior to lifting unit. Failure to do so could
result in death, serious injury, or property damage.
(000351)
(000190)
DANGER
Loss of life. Property damage. Installation must always
comply with applicable codes, standards, laws and
regulations. Failure to do so will result in death
or serious injury.
(000237)
DANGER
Electrical backfeed. Use only approved switchgear to
isolate generator from the normal power source.
Failure to do so will result in death, serious injury,
and equipment damage.

Safety Rules & General Information
Installation Guidelines for Protector Diesel Generators 5
Always recycle batteries in accordance with local laws
and regulations. Contact your local solid waste collection
site or recycling facility to obtain information on local
recycling processes. For more information on battery
recycling, visit the Battery Council International website
at: http://batterycouncil.org
•Follow all safety precautions in the owner’s manual,
installation guidelines manual, and other documents
included with the equipment.
•Never energize a new system without opening all dis-
connects and breakers.
•Always consult local code for additional requirements
for where unit is being installed.
•Incorrect installation can result in personal injury and
damage to the unit. It may also result in the warranty
being suspended or voided. All instructions listed
below must be followed including location clearances
and pipe sizes.
Before You Begin
•Contact local inspector or city hall to be aware of all
federal, state, and local codes which could impact
installation. Secure all required permits before install-
ing.
•Fully comply with all relevant NEC, NFPA, and OSHA
standards, as well as all federal, state, and local
building and electric codes. This unit must be
installed in accordance with current NFPA 37 and
NFPA 70 standards, and any other federal, state, and
local codes for minimum distances from other struc-
tures.
Standards Index
Strictly comply with all applicable national, state, and
local laws, as well as codes or regulations pertaining to
the installation of this engine-generator power system.
Use the most current version of applicable codes or stan-
dards relevant to local jurisdiction, generator used, and
installation site.
NOTE: Not all codes apply to all products and this list is
not all-inclusive. In the absence of pertinent local laws
and standards, the following publications may be used as
a guide (these apply to localities which recognize NFPA
and IBC).
1. National Fire Protection Association (NFPA) 70:
The NATIONAL ELECTRIC CODE (NEC) *
2.
NFPA 10: Standard for Portable Fire Extinguishers *
3. NFPA 30: Flammable and Combustible Liquids Code *
4. NFPA 37: Standard for Stationary Combustion
Engines and Gas Turbines *
5. NFPA 54: National Fuel Gas Code *
6. NFPA 58: Standard for Storage and Handling Of
Liquefied Petroleum Gases *
7. NFPA 68: Standard On Explosion Protection By
Deflagration Venting *
8. NFPA 70E: Standard For Electrical Safety In The
Workplace *
9. NFPA 211: Standard for Chimneys, Fireplaces,
Vents, and Solid Fuel Burning Appliances *
10. NFPA 220: Standard on Types of Building
Construction *
11. NFPA 5000: Building Code *
12. International Building Code **
13. Agricultural Wiring Handbook ***
14. Article X, NATIONAL BUILDING CODE
15. ASAE EP-364.2 Installation and Maintenance of
Farm Standby Electric Power ****
This list is not all-inclusive. Check with the Authority Hav-
ing Local Jurisdiction (AHJ) for any local codes or stan-
dards which may be applicable to your jurisdiction. The
above listed standards are available from the following
Internet sources:
* www.nfpa.org
** www.iccsafe.org
*** www.rerc.org Rural Electricity Resource Council P.O.
Box 309 Wilmington, OH 45177-0309
**** www.asabe.org American Society of Agricultural &
Biological Engineers 2950 Niles Road, St. Joseph, MI 49085
(000182a)
WARNING
Equipment damage. Only qualified service personnel may
install, operate, and maintain this equipment. Failure to follow
proper installation requirements could result in death, serious
injury, and equipment or property damage.
WARNING
to use required safety equipment could result
in death or serious injury. (000257)
Electrocution. Refer to local codes and
standards for safety equipment required when
working with a live electrical system. Failure
WARNING
Environmental Hazard. Always recycle batteries at an
official recycling center in accordance with all local
laws and regulations. Failure to do so could result in
environmental damage, death or serious injury.
(000228)
(000209b)
WARNING
Loss of life. This product is not intended to
be used in a critical life support application.
Failure to adhere to this warning could result
in death or serious injury.

Safety Rules & General Information
6 Installation Guidelines for Protector Diesel Generators
This page intentionally left blank.

Installation Planning
Installation Guidelines for Protector Diesel Generators 7
Section 2: Installation Planning
Protector Diesel Installation Planning
Checklist
 The local building code administrator or fire marshal
has verified the generator must be located a minimum of
________ ft (________m) from a house or other struc-
ture.
NOTE: Minimum distance will be based on local zon-
ing and code requirements.
 The local AHJ has advised me regarding require-
ments for electrical and/or building permits, as well as
those regulations relating to emissions and fuel storage.
 I have been advised of local requirements for con-
struction of a concrete base pad, and whether anchoring
requirements are needed for installation on a flood plain.
 I have verified with the appropriate authorities the
generator must be located a minimum of ________ ft
(_______m) from a property line.
 I have been advised whether the local fire marshal (or
other third party) is required to be present at start up, or
when the fuel tank is filled for the first time.
 I have verified the installation site is applicable to
optional standby only and does not require an NFPA 110
capable generator.
 The local fire marshal has verified I am required to
extend the fuel tank vents ________ ft (_________m)
above the surrounding grade.
 The local fire marshal has verified that local codes
require installation of the diesel product safety accesso-
ries designated on the next page.

Installation Planning
8 Installation Guidelines for Protector Diesel Generators
Safety Accessories
Item Description Part Number Required
Emergency stop switch G006510-0  YES
 NO
90% Fuel fill level alarm
(Domestic product only)
G006504-0  YES
 NO
Five gallon spill box
(Domestic product only)
G006502-0  YES
 NO
Spill box drain back
(Domestic product only)
G006511-0  YES
 NO
Fuel fill drop tube G006507-0  YES
 NO
Fuel tank support risers G006505-0 (15 & 20 kW)
G006506-0 (30, 48, & 50 kW)
 YES  NO
 YES  NO
Stainless steel fuel lines G007660-0 (15 & 20 kW)
G007661-0 (30 kW)
G006516-0 (48 & 50 kW)
 YES  NO
 YES  NO
Lockable fuel fill cap G006512-0  YES
 NO

Installation Planning
Installation Guidelines for Protector Diesel Generators 9
Unit Drawings
Installation Drawings
See Figure 2-1. Installation drawings show weights,
dimensions, clearances, exhaust details, connection
locations, wiring stub-ups, lifting locations, and other
information. Use unit specific installation drawings when
designing a site installation plan. Thoroughly read the
NOTES section of each drawing for important details.
Figure 2-1. Typical Installation Drawing
Wiring Diagrams
Wiring and schematic diagrams show connection points
for control wiring, load wiring, and any service power sup-
ply required for battery chargers, block heaters, etc.
Always use unit specific wiring diagrams during planning
and installation. See Installation Drawings for more
information.
2424 [95.4] OVERALL LENGTH
182
[7.2]
1449
[57.0]
OVERALL
HEIGHT
888 [35.0]
OVERALL WIDTH
758 [29.8]
DOOR TYP
173 [6.8]
618 [24.3]
998 [39.3]
CENTER OF GRAVITY
SEE NOTE 5
1625 [64.0]
343
[13.5]
TITLE
DRAWING CREATED FROM PRO/ENGINEER
SERVICE ITEM 3.4L
OIL FILL CAP RIGHT SIDE
OIL DIP STICK RIGHT SIDE
OIL FILTER RIGHT SIDE
OIL DRAIN HOSE RIGHT SIDE
RADIATOR DRAIN HOSE LEFT SIDE
AIR CLEANER ELEMENT RIGHT SIDE
MUFFLER FRONT
FAN BELT EITHER SIDE
BATTERY LEFT SIDE
WEIGHT DATA WITH EMPTY BASETANK
(SEE NOTE 5)
GENERATOR AS SHOWN (STEEL ENCL)
997 [2197]
WITH WOODEN SHIPPING SKID
1042 [2297]
REFERENCE OWNERS MANUAL FOR PERIODIC
REPLACEMENT PART LISTINGS.
NOTES:
1. MINIMUM RECOMMENDED CONCRETE PAD SIZE: 1194 (47") WIDE X 2718
(107") LONG. REFERENCE INSTALLATION GUIDE SUPPLIED WITH UNIT
FOR CONCRETE PAD GUIDELINES
2. ALLOW SUFFICIENT ROOM ON ALL SIDES OF THE GENERATOR FOR MAINTENANCE
AND SERVICING. THIS UNIT MUST BE INSTALLED IN ACCORDANCE WITH CURRENT
APPLICABLE NFPA 37 AND NFPA 70 STANDARDS AS WELL AS ANY OTHER FEDERAL,
STATE AND LOCAL CODES.
3. CONTROL PANEL / CIRCUIT BREAKER INFORMATION:
- SEE SPECIFICATION SHEET OR OWNERS MANUAL
- ACCESSIBLE THROUGH CUSTOMER ACCESS ASSEMBLY DOOR ON REAR OF
GENERATOR
4. REMOVE THE REAR TANK AND REAR ENCLOSRE COVER PANEL TO ACCESS
THE STUB-UP AREAS AS FOLLOWS:
- HIGH VOLTAGE CONNECTION INCLUDING AC LOAD LEAD CONDUIT CONNECTION
NEUTRAL CONNECTION, BATTERY CHARGER 120 VOLT AC (0.5 AMP MAX) CONNECTION.
- LOW VOLTAGE CONNECTIONS INCLUDING TRANSFER SWITCH CONTROL WIRES
5. CENTER OF GRAVITY AND WEIGHT MAY CHANGE DUE TO UNIT OPTIONS.
6. ENGINE SERVICE CONNECTIONS
OIL DRAIN: 3/8" NPT
EXHAUST OUTLET: 2" O.D.
7. BOTTOM OF GENERATOR SET MUST BE ENCLOSED TO PREVENT PEST INTRUSION AND
RECIRCULATION OF DISCHARGE AIR AND/OR IMPROPER COOLING AIR FLOW.
8. EXHAUST SYSTEM MAXIMUM BACK PRESSURE: 35 INCHES H2O.
9. REFERENCE OWNERS MANUAL FOR LIFTING WARNINGS.
10. MOUNTING BOLTS OR STUDS TO CONCRETE PAD SHALL BE 5/8-11 GRADE 5
(USE STANDARD SAE TORQUE SPECS)
RIGHT SIDE VIEW
REAR VIEW
LEFT SIDE VIEW
RADIATOR/EXHAUST
DISCHARGE AIR
LIFT-OFF DOOR PROVIDES ACCESS TO:
FUEL FILL, FUEL LEVEL GAUGE,
NORMAL VENT, INNER TANK
EMERGENCY VENT, OUTER TANK
EMERGENCY VENT, OPTIONAL
90% ALARM ASSEMBLY,
OPTIONAL 5 GALLON SPILL
BOX
OPEN PUNCHED LOUVERS TYPICAL
ON BOTH SIDES OF
FUEL TANK VENTILATION
DUCT TO PROVIDE ADEQUATE
CROSS-FLOW OF AIR VENTILATION
EXHAUST MUFFLER ENCLOSED WITHIN
GENERATOR ENCLOSURE
REAR TANK COVER
SEE NOTE 4
CUSTOMER ACCESS
ASSEMBLY, CONTROL PANEL
ACCESS, BATTERY CHARGER
LOCATED WITHIN
SEE NOTE 4
CIRCUIT BREAKER
SEE NOTE 3
REAR ENCLOSURE COVER
PANEL
SEE NOTE 4
FUEL TANK
VENTILATION DUCT
LIFTING PROVISIONS (4 PLACES)
SEE NOTES 5, 9, AND CENTER
OF GRAVITY DIMENSIONS
VICE ACTION LATCH,
ONE PER DOOR, LIFT-OFF
DOORS ON FRONT, RIGHT, AND LEFT SIDES
TOP VIEW
RADIATOR/EXHAUST
DISCHARGE AIR
(BOTH SIDES)
AIR INTAKE
(BOTH SIDES)
INTERNAL DIVIDER PANEL
SEPARATES FUEL TANK VENTILATION
DUCT FROM THE ENGINE,
ALTERNATOR AND EXHAUST SYSTEM
REMOVE PANEL TO
ALLOW TANK VENTS
TO TERMINATE OUTSIDE
OF THE GENERATOR
ENCLOSURE (CHECK LOCAL
AND STATE CODE FOR
APPLICABILITY)

Installation Planning
10 Installation Guidelines for Protector Diesel Generators
Receiving
Receiving and Unpacking
Handle shipping cartons and crates with care to avoid
damage. Store and unpack cartons with the correct side
up, as noted by label on shipping carton.
Inspection
Carefully inspect generator and all contents of cartons for
any damage that may have occurred during shipment.
See shipping documentation for any provisions or guid-
ance when damage is incurred. Correct all damage or
deficiencies before installing generator.
Storage Before Installation
Long Term Storage
If unit will be stored (or installed and not started) for six
months or more, store unit in accordance with the manu-
facturer’s instructions. Contact an IASD to obtain the
Long Term Preservation and Storage Manual (Part No.
0G4018) and the Preservation Checklist (Part No.
0G4018A).
Short Term Storage
If unit will be stored (or installed and not started) for less
than six months, proceed as follows:
•All units are provided with an enclosure.
•Place unit on a smooth flat surface. Do not leave unit
on shipping pallet, as it leaves the bottom open for
entry of dirt, debris, insects, rodents, etc.
•Leave exhaust system openings covered.
•Leave plastic plugs in fuel connection points.
•Use anti-rodent plugs and other enclosure features
to prevent entry of birds, small animals, and foreign
objects.
Lifting
Generators weighing more than 900 lbs (408 kg) require
correct tools, equipment, and qualified personnel to be
used in all phases of handling and unpacking.
To ensure personal safety and prevent damage to unit,
use only correctly sized equipment intended for safe rig-
ging, lifting, and moving of heavy machinery. See Lifting
Hazards.
Use a spreader bar to prevent damage to unit. Failure to
use a spreader bar will result in scratches and dam-
age to painted surfaces.
See Figure 2-2. Installation drawings show lifting points
for rigging and lifting purposes. Always attach lifting and
rigging devices at designated points only. Do not use lift-
ing points of the engine or alternator to move generator.
Figure 2-2. Lifting Points (Four Places)
DANGER
(000245)
Risk of electrocution. Avoid touching overhead
power lines when lifting or hoisting generator.
Failure to do so will result in death or serious
injury.
WARNING
Personal injury. Excessive weight. Use only
appropriate lifting eyes and lifting equipment to
lift unit. Improper lifting techniques could result in
equipment damage, death or serious injury. (000224)
WARNING
Personal injury. Failure to properly connect
lifting cables, chains, or straps could result in
death, serious injury, or property damage.
(000346)
WARNING
Personal Injury. Do not use lifting hook if there are
signs of damage or corrosion. Doing so could result
in death, serious injury, or property damage.
(000349)
WARNING
Personal Injury. Do not use lifting eye if there are signs
of damage or corrosion. Doing socould result in death,
serious injury, or property damage.
(000433)
006364

Installation Planning
Installation Guidelines for Protector Diesel Generators 11
Generator Location
IMPORTANT NOTE: Generator exhaust contains car-
bon monoxide (CO)—a poisonous, potentially lethal
gas that cannot be seen or smelled. Generator must
be installed in a well ventilated area away from win-
dows, doors, and openings. The selected location
should not allow exhaust gases to be drawn into
structures where people or animals may be present.
Locate generator set where it is readily accessible for
maintenance, repair, and firefighting purposes. Comply
with code requirements for minimum distance from com-
bustible walls and building openings. Verify generator
location with the local AHJ for code compliance before
positioning generator.
General Location Guidelines
Consider the following:
•See NFPA 37, Section 4.1.3 for rooftop or platform
installations.
•See NFPA 30 for fuel storage tank requirements.
•The supporting structure must be adequate for the
generator and its accessories.
•Verify installation site is clean, dry, not subject to
flooding, and provided with adequate drainage in the
event of heavy rains.
•Verify installation site permits noise and vibration to
be effectively isolated.
•Verify installation site provides easy access to gener-
ator for maintenance, repair, and firefighting pur-
poses.
•Keep a minimum of 5 ft (1.5 m) of clearance around
each side of generator to facilitate service or mainte-
nance.
•Verify installation site permits engine exhaust gases
to be safely evacuated from inhabited or occupied
areas. Consider the direction of prevailing winds to
prevent exhaust gases from being carried back to the
engine area or to the fresh air intake vents of nearby
buildings.
•Installation site must allow for provision of an ade-
quate fuel supply. Consider ease of accessibility for
refueling purposes.
•Verify installation site permits sufficient air flow for
cooling and ventilation. Consider proximity of any
walls, fences, or other noise abatement or security
barriers. Do NOT face radiator discharge end of the
enclosure into prevailing wind.
•Consider cold weather kit options and accessories
for the generator in cold weather locations.
•Verify unit is securely fastened to mounting pad to
prevent movement caused by vibration.
•Verify all electrical connections have flexible sections
to isolate vibration.
NOTE: Failure to comply with location guidelines can
result in damage to generator or surrounding area and
may cause the warranty to be suspended or voided.
Extra repair labor or equipment may not be covered
under warranty if service access is difficult or restricted.
Weather Considerations
Consider local weather conditions during installation.
There are various accessories available to promote fast,
reliable starting and operation regardless of local climatic
conditions. Optional cold weather kits make engine start-
ing more dependable and reliable.
Product Accessories
The following product accessories are available. Contact
an IASD for additional information.
Asphyxiation. Running engines produce
carbon monoxide, a colorless, odorless,
poisonous gas. Carbon monoxide, if not
avoided, will result in death or serious injury.
(000103)
DANGER
1 Scheduled Maintenance Kit
(Part No. G007640-0: 15/20 kW, 12/16 kVa)
2 Scheduled Maintenance Kit
(Part No. G007641-0: 30 kW, 30 kVa)
3 Scheduled Maintenance Kit
(Part No. G006570-1: 48/50 kW, 40/50 kVa)
4 Cold Weather Kit
(Part No. G007651-0: 15/20 kW, 12/16 kVa;
Part No. G007651-0: 30 kW, 30 kVa;
Part No. G006558-0: 48/50 kW, 40/50 kVa)
5 Vent Extension Support Kit
(Part No. G006588-1)
6 Touch-Up Paint Kit
(Part No. G005703-0)
7 Local Wireless Remote
(Part No. G006664-0)
8 Wireless Remote Extension Harness (not shown)
(Part No. G006665-0)
9 Mobile Link™
(Part No. G006463-4)
10 Harness Adapter Kit (not shown)
(Part No. G006478-0)

Installation Planning
12 Installation Guidelines for Protector Diesel Generators
1
2
3
4
5
6
7
9

Site Selection and Preparation
Installation Guidelines for Protector Diesel Generators 13
Section 3: Site Selection and Preparation
Site Selection
Generator must be installed outdoors in a location allow-
ing sufficient clearance around all sides for reasons of
safety, maintenance, and servicing.
Placement requirements for a diesel storage tank vary by
municipality. Contact the local building code department
and fire marshal for code compliance before selecting a
location for the generator. See NFPA 37 and NFPA 30 for
additional requirements for placement of a diesel storage
tank. See Installation Checklists for additional details.
NOTE: Local codes may be different and more restrictive
than what is described here. Contact local AHJ to deter-
mine which standards and codes apply in the area.
Install generator, in its protective enclosure, outdoors,
where adequate cooling and ventilating air is always
available. Consider these factors:
•Installation of the diesel generator must strictly
comply with NFPA 30, NFPA 37, NFPA 54, NFPA
58 and NFPA 70 standards.
•Install unit where air inlet and outlet openings will
not become obstructed by leaves, grass, snow, etc.
Consider using a windbreak to protect unit if pre-
vailing winds will cause blowing or drifting.
•Install generator on high ground where water levels
will not rise and endanger it. It should not operate
in or be subjected to standing water.
•Allow sufficient room on all sides of generator for
maintenance and servicing. This unit must be
installed in accordance with any codes that are in
place in your country or local jurisdiction for mini-
mum distances from other structures.
•Clearance from ends and front of generator must
meet the requirements of NFPA 30, NFPA 37, and
all additional local code requirements.
•Clearances under a deck or structure must meet
requirements of NFPA 30, NFPA 37, and all addi-
tional local code requirements.
•Install unit where rain gutter downspouts, roof run-
off, landscape irrigation, water sprinklers, or sump
pump discharge does not flood unit or spray enclo-
sure, including any air inlet or outlet openings.
•Install unit where services will not be affected or
obstructed, including concealed, underground, or
covered services such as electrical, fuel, phone, air
conditioning, or irrigation. This could affect war-
ranty coverage.
•Face generator air inlet openings to the prevailing
winds if strong prevailing winds blow from one
direction.
•In the absence of local codes regarding placement
or clearance, the manufacturer recommend follow-
ing the guidelines in this section.
•Install generator as close as possible to transfer
switch. REMEMBER THAT LAWS OR CODES
MAY REGULATE THE DISTANCE AND LOCA-
TION.
•Generator must be installed on a level surface, and
must be level within 0.5 in (13 mm) all around.
Installation Guidelines for Stationary Fuel
Storage Tanks
National Fire Protection Association standard NFPA 30
indicates spacing requirements of a stationary fuel stor-
age tank with a mounted, enclosed generator from a
structure, wall, or property line. Verify all spacing require-
ments are correct with the assistance of local code offi-
cials prior to finalizing genset location.
If generator is not set to OFF mode, it can crank and start
as soon as battery cables are connected. If utility power
supply is not turned off, sparking can occur at battery
posts and cause an explosion.
Asphyxiation. Running engines produce
carbon monoxide, a colorless, odorless,
poisonous gas. Carbon monoxide, if not
avoided, will result in death or serious injury.
(000103)
DANGER
Automatic start-up. Disconnect utility power and
render unit inoperable before working on unit.
Failure to do so will result in death or serious injury.
(000191)
DANGER

Site Selection and Preparation
14 Installation Guidelines for Protector Diesel Generators
Site Preparation
Generator Foundation
Install generator on a concrete pad or base slab able to
support its weight and accessories. All applicable codes
should be followed. A correct foundation is needed to
resist dynamic loading and reduce transmitted noise and
vibration. The exact composition of the mounting pad
must follow standard engineering practices for the
required loading and application. Securely fasten gen-
erator to foundation using suitable grade, size, and
style fasteners. Holes are provided in the base frame for
this purpose.
Concrete Pad
Follow all federal, state, and local codes when designing
a concrete pad or base slab.
Seat concrete pad on a prepared solid subsurface and
use appropriate reinforcing bar or expanded wire mesh.
A common specification calls for 2,500 psi (17.24 MPa)
concrete reinforced with 8 gauge wire mesh.
Dimensions
Extend concrete pad beyond the frame of the unit at least
6 in (15.2 cm). This provides space for maintenance and
repair.
The base pad must be:
•Capable of supporting 125% of unit wet weight for
single unit applications.
•Flat and level to within 0.5 in (13 mm).
•Capable of withstanding severe torque reactions.
To calculate depth of concrete pad, the following formula
may be used:
W = Total wet weight of generator set in lbs (kg)
Density = Density of the concrete:
•150 pounds per cubic foot
•2,400 kilograms per cubic meter
B = Foundation width in ft (meters)
L = Foundation length in ft (meters)
Suggested mixture of concrete (by volume) is 1:2:3 of
cement, sand, and aggregate with a maximum 4 in (100
mm) slump with a 28 day compression strength of 3,000
psi (20.7 MPa).
Unit Clearance
Verify installation site provides easy access to generator
for maintenance, repair, and firefighting purposes. Keep
a minimum of 5 ft (1.5 m) of clearance around each side
of the generator to facilitate service or maintenance.
Stub-Up Area
For load conduit, auxiliary power conduit (high voltage),
and control wiring conduit (low voltage), see unit installa-
tion drawings for the location and dimensions of the stub-
up area. Figure 3-1 illustrates a typical stub opening (A).
Figure 3-1. Installation Drawing Stub-Up Detail
(Typical)
Depth of Base = W
Density x B x L
002771
3.9
(100)
4.1 (104.5)
1.9 (50) 0.4 (9) 2.0 (51)
In. (mm)
A

Site Selection and Preparation
Installation Guidelines for Protector Diesel Generators 15
Mounting
Fixed Foundation
Use mounting holes in base frame to fasten unit to foun-
dation. Always use hardware of a suitable grade, size,
and style.
Connections
All electrical connections must have flexible sections to
isolate vibration if they connect to the unit base rails. Cor-
rectly support and secure all piping before installing flexi-
ble connection.
Combustible Floor and Roof Protection
Engines, and their weatherproof housings, if provided,
that are installed on roofs of structures shall be located at
least 5 ft (1.5 m) from openings in walls and at least 5 ft
(1.5 m) from structures having combustible walls. Per
NEC 110.26(E)(2), a minimum separation of 3 ft (0.91 m)
is permitted if the adjacent wall of the structure has a fire
resistance rating of at least 1 hour.
An oil containment system consisting of a curb or dike
having a capacity at least equal to the total capacity of
the lubricating oil system or the liquid fuel system, which-
ever is greater, shall be provided. This system shall also
comply with applicable requirements of NFPA 37, Chap-
ter 6.
The surface beneath the engine and beyond the engine
and the oil containment dike shall be noncombustible to a
minimum distance of 12 in (300 mm).
NOTE: Local building codes may have additional re-
quirements for placement of fuel storage tanks on top of
a roof or structure. Contact the local building code
department or fire marshal for code compliance before
placing generator on top of roof or structure.

Site Selection and Preparation
16 Installation Guidelines for Protector Diesel Generators
This page intentionally left blank.