General life Ht100s rf User manual

BATTERY PLACEMENT

As shown in the picture above, press the screwdriver forward from the

space shown, bend the tabs and separate the front cover. Insert 2 new

AAA alkaline batteries in the battery housing with the correct battery

direction. Replace both batteries at the same time. Then align the front

part of your Room Thermostat to the back and squeeze it towards the

back.

WARNING!

When the product is not used for a long period (more than 15 days),

remove the batteries. Otherwise, malfunctions that may occur would be

out of warranty.

Please throw your dead batteries into the waste bin for batteries.

RECEIVER PLACEMENT

The important things to note for the Receiver

placement is avoiding physical contact

between the Receiver and boiler, and

protecting it against materials such as

liquid,dust etc.

The devices should be placed in order to minimize the damage to the

received and transmitted signals by paying attention to the following

points;

The devices should not be mounted on metal surfaces.

The devices should not be installed close to electrical cables and

electronic equipment such as computers and television units.

The devices should not be installed near large metal structures or

other building materials using ﬁne metal meshes such as special

glass or special concrete.

Distance between the Room Thermostat and the Receiver should not

exceed 20 meters or 2 ﬂoors.

Receiver must be installed at least 50 cm away from the boiler.

RECEIVER SETUP

First, shut down your boiler and your boiler's power source with all

electrical current (fuse,socket etc.)

 As shown in the connection diagram, connect one end of the boiler

connection cable to the COM and the other to the NO input.of the

Receiver.

 Connect the other ends of the cable -which you connected to the

Receiver- to room thermostat connection terminal as shown in your

boiler's user manual.

 You must ﬁrst connect the Receiver power cable to the Receiver and

then to the fuse to which the boiler is connected.

 After completing the cable connection process,ﬁrstly turn on your

fuse and then your boiler.

 By pressing the Receiver's manual usage button for 2 seconds, you

should see the Orange Light blinking on the Receiver. In this way, after

making sure that the boiler is operating, press the same button again

for 2 seconds and see that the Orange LED turns off.

Set up the Room Thermostat to pair the Receiver with the Room

Thermostat.

Room Thermostat Indicator LED Descriptions

RECEIVER

RECEIVER LED DESCRIPTIONS

ROOM THERMOSTAT PLACEMENT

Room Thermostat needs to be placed in the room which is used most

frequently. For instance; living room or lounge. Placing the Room

Thermostat in a spot that have air circulation like entrance of a room or

side of window should be avoided. Also anywhere close to heating units

such as radiator, stove and spots which get direct sun lights would not

be suitable. Room Thermostat needs to be located above the ﬂoor

150 cm height. Few trials may be made to ﬁnd the most convenient spot.

GENERAL SPECIFICATIONS

HT100S RF is a wireless room thermostat. The user can adjust the

room temperature with the required temperature and get more

comfortable and economic heating.

Precise Temperature Measurement Wireless Connection

ON/OFF Control TPI Algorithm

HT100S RF AND EQUIPMENTS

TECHNICAL DATA

Room Thermostat

Receiver

ROOM THERMOSTAT

12 3

HT100S RF

Room Thermostat

generallife.com.tr

85mm / 125mm / 24mm

3V DC (2 x AAA alkaline battery)

0.1 C

o o

(5 C) – (35 C)

1 Year (2 x AAA)

o o

(-10 C) – (+50 C)

o o

(-20 C) – (+60 C)

HT100S RF USER MANUAL

Alkaline

Battery

AAA

HT100S RF

USER MANUAL

DIGITAL ROOM THERMOSTAT

Room Thermostat sends a close signal to the

Receiver and the heating unit stops operating.

Room Thermostat sends an open signal to

the Receiver and the heating unit starts.

Room Thermostat sends a pairing signal to

the Receiver.

If it blinks once

If it blinks twice

If it blinks three times

ENGLISH

generallife.com.tr

DIGITAL ROOM THERMOSTAT

Dimensions ( H / L / W )

Operating Current

Temperature Measurement

Accuracy

Operating Temperature Range

Battery Life

Operating Temperature

Storage Temperature

Steady Red

Blinking Green

Steady Green

3 Short Orange

Blinking

Steady Orange

3 Short Green

Blinking

Blinking Orange

Blinking Red

1-Manual Operation Button:

By disabling the Receiver, it enables you

to use your boiler manually.

2-Pairing Button:

Allows to pair the Receiver with the

Room Thermostat.

3-Receiver LED Light

4-Receiver Power Cable Input

5-Boiler Connection Cable Input

150 cm

min.20 cm

Receiver has power but Receiver and

Room Thermostat are not paired.

Waiting for pairing signal from Room Thermostat.

Receiver and Room Thermostat are paired.

Boiler is not operating.

Operate the boiler signal has reached to the

Receiver.

Boiler is operating.

Shut the boiler down signal has reached to the

Receiver.

Boiler is operating in manual mode.

Receiver did not get a signal from the

Room Thermostat for 22 minutes or longer and

boiler has shut down.

Adjustment Knob

Indicator LED

Dowels and Screws

Receiver

Holder

90mm / 90mm / 25mm

230V AC

7A (240VAC – Resistive load)

10A (120VAC – Resistive load)

o o

(-20 C) – (+60 C)

Dimensions

Operation Current

Relay NO Switching Current

Storage Temperature

BATTERY PLACEMENT

As shown in the picture above, press the screwdriver forward from the

space shown, bend the tabs and separate the front cover. Insert 2 new

AAA alkaline batteries in the battery housing with the correct battery

direction. Replace both batteries at the same time. Then align the front

part of your Room Thermostat to the back and squeeze it towards the

back.

WARNING!

When the product is not used for a long period (more than 15 days),

remove the batteries. Otherwise, malfunctions that may occur would be

out of warranty.

Please throw your dead batteries into the waste bin for batteries.

RECEIVER PLACEMENT

The important things to note for the Receiver

placement is avoiding physical contact

between the Receiver and boiler, and

protecting it against materials such as

liquid,dust etc.

The devices should be placed in order to minimize the damage to the

received and transmitted signals by paying attention to the following

points;

The devices should not be mounted on metal surfaces.

The devices should not be installed close to electrical cables and

electronic equipment such as computers and television units.

The devices should not be installed near large metal structures or

other building materials using ﬁne metal meshes such as special

glass or special concrete.

Distance between the Room Thermostat and the Receiver should not

exceed 20 meters or 2 ﬂoors.

Receiver must be installed at least 50 cm away from the boiler.

RECEIVER SETUP

First, shut down your boiler and your boiler's power source with all

electrical current (fuse,socket etc.)

 As shown in the connection diagram, connect one end of the boiler

connection cable to the COM and the other to the NO input.of the

Receiver.

 Connect the other ends of the cable -which you connected to the

Receiver- to room thermostat connection terminal as shown in your

boiler's user manual.

 You must ﬁrst connect the Receiver power cable to the Receiver and

then to the fuse to which the boiler is connected.

 After completing the cable connection process,ﬁrstly turn on your

fuse and then your boiler.

 By pressing the Receiver's manual usage button for 2 seconds, you

should see the Orange Light blinking on the Receiver. In this way, after

making sure that the boiler is operating, press the same button again

for 2 seconds and see that the Orange LED turns off.

Set up the Room Thermostat to pair the Receiver with the Room

Thermostat.

Room Thermostat Indicator LED Descriptions

RECEIVER

RECEIVER LED DESCRIPTIONS

ROOM THERMOSTAT PLACEMENT

Room Thermostat needs to be placed in the room which is used most

frequently. For instance; living room or lounge. Placing the Room

Thermostat in a spot that have air circulation like entrance of a room or

side of window should be avoided. Also anywhere close to heating units

such as radiator, stove and spots which get direct sun lights would not

be suitable. Room Thermostat needs to be located above the ﬂoor

150 cm height. Few trials may be made to ﬁnd the most convenient spot.

GENERAL SPECIFICATIONS

HT100S RF is a wireless room thermostat. The user can adjust the

room temperature with the required temperature and get more

comfortable and economic heating.

Precise Temperature Measurement Wireless Connection

ON/OFF Control TPI Algorithm

HT100S RF AND EQUIPMENTS

TECHNICAL DATA

Room Thermostat

Receiver

ROOM THERMOSTAT

12 3

HT100S RF

Room Thermostat

generallife.com.tr

85mm / 125mm / 24mm

3V DC (2 x AAA alkaline battery)

0.1 C

o o

(5 C) – (35 C)

1 Year (2 x AAA)

o o

(-10 C) – (+50 C)

o o

(-20 C) – (+60 C)

HT100S RF USER MANUAL

Alkaline

Battery

AAA

HT100S RF

USER MANUAL

DIGITAL ROOM THERMOSTAT

Room Thermostat sends a close signal to the

Receiver and the heating unit stops operating.

Room Thermostat sends an open signal to

the Receiver and the heating unit starts.

Room Thermostat sends a pairing signal to

the Receiver.

If it blinks once

If it blinks twice

If it blinks three times

ENGLISH

generallife.com.tr

DIGITAL ROOM THERMOSTAT

Dimensions ( H / L / W )

Operating Current

Temperature Measurement

Accuracy

Operating Temperature Range

Battery Life

Operating Temperature

Storage Temperature

Steady Red

Blinking Green

Steady Green

3 Short Orange

Blinking

Steady Orange

3 Short Green

Blinking

Blinking Orange

Blinking Red

1-Manual Operation Button:

By disabling the Receiver, it enables you

to use your boiler manually.

2-Pairing Button:

Allows to pair the Receiver with the

Room Thermostat.

3-Receiver LED Light

4-Receiver Power Cable Input

5-Boiler Connection Cable Input

150 cm

min.20 cm

Receiver has power but Receiver and

Room Thermostat are not paired.

Waiting for pairing signal from Room Thermostat.

Receiver and Room Thermostat are paired.

Boiler is not operating.

Operate the boiler signal has reached to the

Receiver.

Boiler is operating.

Shut the boiler down signal has reached to the

Receiver.

Boiler is operating in manual mode.

Receiver did not get a signal from the

Room Thermostat for 22 minutes or longer and

boiler has shut down.

Adjustment Knob

Indicator LED

Dowels and Screws

Receiver

Holder

90mm / 90mm / 25mm

230V AC

7A (240VAC – Resistive load)

10A (120VAC – Resistive load)

o o

(-20 C) – (+60 C)

Dimensions

Operation Current

Relay NO Switching Current

Storage Temperature

BATTERY PLACEMENT

As shown in the picture above, press the screwdriver forward from the

space shown, bend the tabs and separate the front cover. Insert 2 new

AAA alkaline batteries in the battery housing with the correct battery

direction. Replace both batteries at the same time. Then align the front

part of your Room Thermostat to the back and squeeze it towards the

back.

WARNING!

When the product is not used for a long period (more than 15 days),

remove the batteries. Otherwise, malfunctions that may occur would be

out of warranty.

Please throw your dead batteries into the waste bin for batteries.

RECEIVER PLACEMENT

The important things to note for the Receiver

placement is avoiding physical contact

between the Receiver and boiler, and

protecting it against materials such as

liquid,dust etc.

The devices should be placed in order to minimize the damage to the

received and transmitted signals by paying attention to the following

points;

The devices should not be mounted on metal surfaces.

The devices should not be installed close to electrical cables and

electronic equipment such as computers and television units.

The devices should not be installed near large metal structures or

other building materials using ﬁne metal meshes such as special

glass or special concrete.

Distance between the Room Thermostat and the Receiver should not

exceed 20 meters or 2 ﬂoors.

Receiver must be installed at least 50 cm away from the boiler.

RECEIVER SETUP

First, shut down your boiler and your boiler's power source with all

electrical current (fuse,socket etc.)

 As shown in the connection diagram, connect one end of the boiler

connection cable to the COM and the other to the NO input.of the

Receiver.

 Connect the other ends of the cable -which you connected to the

Receiver- to room thermostat connection terminal as shown in your

boiler's user manual.

 You must ﬁrst connect the Receiver power cable to the Receiver and

then to the fuse to which the boiler is connected.

 After completing the cable connection process,ﬁrstly turn on your

fuse and then your boiler.

 By pressing the Receiver's manual usage button for 2 seconds, you

should see the Orange Light blinking on the Receiver. In this way, after

making sure that the boiler is operating, press the same button again

for 2 seconds and see that the Orange LED turns off.

Set up the Room Thermostat to pair the Receiver with the Room

Thermostat.

Room Thermostat Indicator LED Descriptions

RECEIVER

RECEIVER LED DESCRIPTIONS

ROOM THERMOSTAT PLACEMENT

Room Thermostat needs to be placed in the room which is used most

frequently. For instance; living room or lounge. Placing the Room

Thermostat in a spot that have air circulation like entrance of a room or

side of window should be avoided. Also anywhere close to heating units

such as radiator, stove and spots which get direct sun lights would not

be suitable. Room Thermostat needs to be located above the ﬂoor

150 cm height. Few trials may be made to ﬁnd the most convenient spot.

GENERAL SPECIFICATIONS

HT100S RF is a wireless room thermostat. The user can adjust the

room temperature with the required temperature and get more

comfortable and economic heating.

Precise Temperature Measurement Wireless Connection

ON/OFF Control TPI Algorithm

HT100S RF AND EQUIPMENTS

TECHNICAL DATA

Room Thermostat

Receiver

ROOM THERMOSTAT

12 3

HT100S RF

Room Thermostat

generallife.com.tr

85mm / 125mm / 24mm

3V DC (2 x AAA alkaline battery)

0.1 C

o o

(5 C) – (35 C)

1 Year (2 x AAA)

o o

(-10 C) – (+50 C)

o o

(-20 C) – (+60 C)

HT100S RF USER MANUAL

Alkaline

Battery

AAA

HT100S RF

USER MANUAL

DIGITAL ROOM THERMOSTAT

Room Thermostat sends a close signal to the

Receiver and the heating unit stops operating.

Room Thermostat sends an open signal to

the Receiver and the heating unit starts.

Room Thermostat sends a pairing signal to

the Receiver.

If it blinks once

If it blinks twice

If it blinks three times

ENGLISH

generallife.com.tr

DIGITAL ROOM THERMOSTAT

Dimensions ( H / L / W )

Operating Current

Temperature Measurement

Accuracy

Operating Temperature Range

Battery Life

Operating Temperature

Storage Temperature

Steady Red

Blinking Green

Steady Green

3 Short Orange

Blinking

Steady Orange

3 Short Green

Blinking

Blinking Orange

Blinking Red

1-Manual Operation Button:

By disabling the Receiver, it enables you

to use your boiler manually.

2-Pairing Button:

Allows to pair the Receiver with the

Room Thermostat.

3-Receiver LED Light

4-Receiver Power Cable Input

5-Boiler Connection Cable Input

150 cm

min.20 cm

Receiver has power but Receiver and

Room Thermostat are not paired.

Waiting for pairing signal from Room Thermostat.

Receiver and Room Thermostat are paired.

Boiler is not operating.

Operate the boiler signal has reached to the

Receiver.

Boiler is operating.

Shut the boiler down signal has reached to the

Receiver.

Boiler is operating in manual mode.

Receiver did not get a signal from the

Room Thermostat for 22 minutes or longer and

boiler has shut down.

Adjustment Knob

Indicator LED

Dowels and Screws

Receiver

Holder

90mm / 90mm / 25mm

230V AC

7A (240VAC – Resistive load)

10A (120VAC – Resistive load)

o o

(-20 C) – (+60 C)

Dimensions

Operation Current

Relay NO Switching Current

Storage Temperature

BATTERY PLACEMENT

As shown in the picture above, press the screwdriver forward from the

space shown, bend the tabs and separate the front cover. Insert 2 new

AAA alkaline batteries in the battery housing with the correct battery

direction. Replace both batteries at the same time. Then align the front

part of your Room Thermostat to the back and squeeze it towards the

back.

WARNING!

When the product is not used for a long period (more than 15 days),

remove the batteries. Otherwise, malfunctions that may occur would be

out of warranty.

Please throw your dead batteries into the waste bin for batteries.

RECEIVER PLACEMENT

The important things to note for the Receiver

placement is avoiding physical contact

between the Receiver and boiler, and

protecting it against materials such as

liquid,dust etc.

The devices should be placed in order to minimize the damage to the

received and transmitted signals by paying attention to the following

points;

The devices should not be mounted on metal surfaces.

The devices should not be installed close to electrical cables and

electronic equipment such as computers and television units.

The devices should not be installed near large metal structures or

other building materials using ﬁne metal meshes such as special

glass or special concrete.

Distance between the Room Thermostat and the Receiver should not

exceed 20 meters or 2 ﬂoors.

Receiver must be installed at least 50 cm away from the boiler.

RECEIVER SETUP

First, shut down your boiler and your boiler's power source with all

electrical current (fuse,socket etc.)

 As shown in the connection diagram, connect one end of the boiler

connection cable to the COM and the other to the NO input.of the

Receiver.

 Connect the other ends of the cable -which you connected to the

Receiver- to room thermostat connection terminal as shown in your

boiler's user manual.

 You must ﬁrst connect the Receiver power cable to the Receiver and

then to the fuse to which the boiler is connected.

 After completing the cable connection process,ﬁrstly turn on your

fuse and then your boiler.

 By pressing the Receiver's manual usage button for 2 seconds, you

should see the Orange Light blinking on the Receiver. In this way, after

making sure that the boiler is operating, press the same button again

for 2 seconds and see that the Orange LED turns off.

Set up the Room Thermostat to pair the Receiver with the Room

Thermostat.

Room Thermostat Indicator LED Descriptions

RECEIVER

RECEIVER LED DESCRIPTIONS

ROOM THERMOSTAT PLACEMENT

Room Thermostat needs to be placed in the room which is used most

frequently. For instance; living room or lounge. Placing the Room

Thermostat in a spot that have air circulation like entrance of a room or

side of window should be avoided. Also anywhere close to heating units

such as radiator, stove and spots which get direct sun lights would not

be suitable. Room Thermostat needs to be located above the ﬂoor

150 cm height. Few trials may be made to ﬁnd the most convenient spot.

GENERAL SPECIFICATIONS

HT100S RF is a wireless room thermostat. The user can adjust the

room temperature with the required temperature and get more

comfortable and economic heating.

Precise Temperature Measurement Wireless Connection

ON/OFF Control TPI Algorithm

HT100S RF AND EQUIPMENTS

TECHNICAL DATA

Room Thermostat

Receiver

ROOM THERMOSTAT

12 3

HT100S RF

Room Thermostat

generallife.com.tr

85mm / 125mm / 24mm

3V DC (2 x AAA alkaline battery)

0.1 C

o o

(5 C) – (35 C)

1 Year (2 x AAA)

o o

(-10 C) – (+50 C)

o o

(-20 C) – (+60 C)

HT100S RF USER MANUAL

Alkaline

Battery

AAA

HT100S RF

USER MANUAL

DIGITAL ROOM THERMOSTAT

Room Thermostat sends a close signal to the

Receiver and the heating unit stops operating.

Room Thermostat sends an open signal to

the Receiver and the heating unit starts.

Room Thermostat sends a pairing signal to

the Receiver.

If it blinks once

If it blinks twice

If it blinks three times

ENGLISH

generallife.com.tr

DIGITAL ROOM THERMOSTAT

Dimensions ( H / L / W )

Operating Current

Temperature Measurement

Accuracy

Operating Temperature Range

Battery Life

Operating Temperature

Storage Temperature

Steady Red

Blinking Green

Steady Green

3 Short Orange

Blinking

Steady Orange

3 Short Green

Blinking

Blinking Orange

Blinking Red

1-Manual Operation Button:

By disabling the Receiver, it enables you

to use your boiler manually.

2-Pairing Button:

Allows to pair the Receiver with the

Room Thermostat.

3-Receiver LED Light

4-Receiver Power Cable Input

5-Boiler Connection Cable Input

150 cm

min.20 cm

Receiver has power but Receiver and

Room Thermostat are not paired.

Waiting for pairing signal from Room Thermostat.

Receiver and Room Thermostat are paired.

Boiler is not operating.

Operate the boiler signal has reached to the

Receiver.

Boiler is operating.

Shut the boiler down signal has reached to the

Receiver.

Boiler is operating in manual mode.

Receiver did not get a signal from the

Room Thermostat for 22 minutes or longer and

boiler has shut down.

Adjustment Knob

Indicator LED

Dowels and Screws

Receiver

Holder

90mm / 90mm / 25mm

230V AC

7A (240VAC – Resistive load)

10A (120VAC – Resistive load)

o o

(-20 C) – (+60 C)

Dimensions

Operation Current

Relay NO Switching Current

Storage Temperature

Your Room Thermostat sends the last status signal to the Receiver

every 10 minutes. Thus, your Room Thermostat and Receiver work

synchronously. If the signal cannot reach to the Receiver from the

Room Thermostat for 22 minutes, it perceives that the connection is

broken and stops the boiler operation for safety reasons.Likewise, in

cases where the electricity comes back after a power failure, the

Receiver do not operate the boiler until 'operate' signal reaches from

the Room Thermostat.

However, in this case, if the Room Thermostat continues to operate

normally, it will continue to work properly without any need for

intervention since it sends a status signal to the Receiver every 10

minutes.

WHAT TO KNOW ABOUT TPI ROOM THERMOSTAT

If the placement of the TPI Room Thermostats is changed, the

learning process will restart. The learning process should be

considered as 7 days.

If the TPI Room Thermostats are de-energized (battery replacement),

the learning process will restart. The learning process should be

considered as 7 days.

FREQUENTLY ASKED QUESTIONS

Is my Room Thermostat compatible with my boiler?

If your boiler has on-off connections, your Room Thermostat is

compatible. You can learn the information about your boiler from the

boiler user manual or your boiler service.

How will I connect my boiler with my Receiver?

We recommend that the connection between your Receiver and your

boiler should be made by professionally qualiﬁed persons.

2x0.75 mm cable is suﬃcient for the Receiver - boiler connection.

Connect one end of the cable pair to the room thermostat connection

terminals stated in the user manual of your boiler.

Connect the other end of the cable pair to COM and NO inputs of the

terminal inside the Receiver as shown in the "RECEIVER WIRING

DIAGRAM" section.

The direction of the cable ends does not matter.

DECLARATION OF CONFORMITY

ISIPARK İÇ VE DIŞ TİC. İNŞ. ISITMA SİSTEMLERİ OTO. SAN.A.Ş.which

Head Oﬃce and production site is located on Fatih Mah. 1188

Sk.No:13/A Sarnıç - Gaziemir - İZMİR – TÜRKİYE conﬁrms and

declares that the product marked with CE and its speciﬁcations below

is covered by the provisions of the mentioned directive.

Brand

Product Name

Product Type

Compatible Directives:

Radio and Telecommunications Terminal Equipment Regulation

2014/53/EU (R&TTE/RED EN 301 489-1 V2.1.1:2017,

EN 300 220-1 V3.1.1:2017, EN 301 489-3 V2.1.1:2017,

EN 300 220-2 V3.1.1:2017, EN 62479: 2010)

Electromagnetic Compatibility Regulation 2014/30/EU

(EMC EN 61000-6-3: 2007 + A1: 2011, EN 61000-6-1: 2007)

Low Voltage Directive 2014/35/EU

(LVD EN 60730-2-9:2010, EN 60730-1:2011)

Additional Information: The mentioned product can be used with

boilers with on / off output and compliance with the directives only

covers the product. ISIPARK is not responsible for the entire system's

compliance with the directives. This statement is not valid if changes

are made to the product without our approval.

4 55 6

ISIPARK reserves the rights of changing product speciﬁcations and

user manuals.

* For all changes, you may visit generallife.com.tr

Vendor

Title:

Adress:

Tel: Fax:

E-Mail:

Invoice Date and Number:

Delivery Time and Place:

Authorized Signature:

Company Stamp:

Product

Type: Digital Room Thermostat

Brand: GENERAL Life

Model: HT100S RF

STAMP

V-01.2022

WARRANTY CERTIFICATE

Manufacturer

Title: ISIPARK İÇ DIŞ TİC. A.Ş.

Adress: Fatih Mah. 1188 Sk. No:13/A Sarnıç

Gaziemir İzmir-TÜRKİYE

Tel: +90 (232) 457 99 50

Fax: +90 (232) 457 91 22

E-mail: generallife@generallife.com.tr

Authorized Signature:

Company Stamp:

Product

Type: Digital Room Thermostat

Brand: GENERAL Life

Model: HT100S RF

Warranty Period: 5 Years

Max. Time to Repair: 20 Days

Bandrol and Serial Number:

RECEIVER WIRING DIAGRAM

WARNING!

Operations inside the boiler or related to the electrical installation

must be carried out by persons with professional competence.

PAIRING THE ROOM THERMOSTAT AND THE RECEIVER

Keep pressing the Receiver's pairing button for 2 seconds and see

that the LED on the Receiver is blinking green.

Turn the Room Thermostat button to the “ ” ( pairing) symbol.

The LED of the Room Thermostat will blink 3 times.

 If the pairing is successful, the green ﬂashing LED on the Receiver

will be steadily lit.

 Receiver and Room Thermostat have now been synced.

TPI ROOM THERMOSTAT WORKING LOGIC

Your Room Thermostat works with the TPI algorithm in the heating

option. Room Thermostats using TPI technology predict when the

temperature of your home will rise above or below the set

temperature and turn the heating unit on and off accordingly. This

ensures that your home stays at the temperature you set without

maximum deviations up and down.

What is TPI?

TPI technology is designed to ensure that you get the best possible

energy eﬃciency from your heating system. It measures and applies the

best possible timings to deliver and maintain your home at the set

temperature level.

How does TPI work?

Thanks to the advanced artiﬁcial intelligence technology found in the

software, it adapts to the temperature change of the environment in

which it is located. By creating a general temperature map of your home,

it learns how long it takes to reach the desired room temperature and

how to maintain this temperature. In this way, it provides minimum

energy consumption by calculating how long your heating unit should

work for.

What is the difference?

In non-TPI room thermostats, the heating unit works and stops

continuously until it exceeds the set temperature value. If the set

temperature drops below a certain amount, the heating unit will work

again. This creates greater temperature ﬂuctuations and less energy

control. TPI Room Thermostats, on the other hand, provide higher

savings and comfort compared to On/Off room thermostats with the

advantages it has.

TPI ROOM THERMOSTAT WORKING GRAPHIC

: GENERAL Life

: HT100S RF

: Digital Room Thermostat

WARRANTY CONDITIONS

1- The warranty period starts from the invoice date and warranted against

manufacturing defects for 5 years.

2- Devices and apparatus are delivered to the customer in working condition in

our company. On-site commissioning is subject to a service fee.

3-The repair of the devices and apparatus covered by the warranty is carried out

in our company factory and should send by contracted transportation

company. In on-site services, the transportation and accommodation expenses

of the service personnel belong to the customer. The shift fee during

transportation is added to the service fee and collected in advance.

4-The maintenance of devices and apparatus is done in our company. For the

maintenance of the devices and apparatus, the round travel fares belongs to the

customer.

5-In case of malfunctioning of the devices and apparatus whose warranty

period continues, it is tested in our company whether the malfunction is caused

by a customer or manufacturer fault, and it is reported with a report issued by

our company.

6-In case of detection of manufacturer-induced errors of devices and apparatus

whose warranty period continues, the customer can request a replacement or

repair of the devices and apparatus at full expense by the manufacturer, unless

it's higher than the product's price

7-In the event that the faults of the devices and apparatus whose warranty

period continues are determined as caused by the customer, all expenses

would be belong to the customer.

8-Customers should be aware of damages (if there is any) of product and warn

manufacturer since the day warranty duration starts.If customer do not warn

manufacturer with knowledge of damage, customer lose the rights of article 6.

9-Malfunctions resulting from the use of devices and apparatus contrary to the

matters stated in the User Manual are not covered by the warranty.

10-Devices and their apparatus are out of warranty if they are beaten, broken or

scratched by the customer.

11-Damages resulting from the use of devices and apparatus belonging to

other brands and models without the approval of the manufacturer are not

covered by the warranty.

12-Battery leakage and errors due to rust, oxidation and liquid contact by

working in acidic / humid environments are not covered by the warranty.

13-When the product is not used for a long period (more than 15 days), remove

the batteries. Otherwise, malfunctions that will occur are out of warranty.

14-Damages that may occur during the transportation of devices and

apparatus are not covered by the warranty. Customers can take a

transportation insurance.

15-Damages caused by mains voltage / faulty electrical installation are not

covered by the warranty.

16-Devices and apparatuses are out of warranty for malfunctions caused by

force majeure such as ﬁre, ﬂood, earthquake etc.

17-All of the devices and apparatuses, including all their parts, are under the

warranty of our company.

18-In case of malfunction of the devices and apparatuses within the warranty

period, the time spent during repairment period is added to the warranty period.

The repair period of the product cannot exceed 20 working days. This period

starts from the date of notiﬁcation to the service station of the malfunction

related to the product or, in the absence of a service station, to the seller, dealer,

agency, representative, importer or manufacturer of the product. Consumer can

report the problem by; phone, fax, e-mail, registered and reply paid letter or a

similar way. However, in case of a conﬂict, responsibility of prove is belong to

the customer. If the malfunction of the product is not repaired within 20 working

days, the manufacturer-producer or importer; has to allocate another product

with similar features to the use of the consumer until the repair of the product is

completed,

19-Although the consumer uses his/her repair rights,

-If the product breaks down for 4 times in a year or 6 times in warranty duration

and these problems effects main purpose of the product.

(starting from delivery time during warranty.)

- Exceeding the maximum time required for repair,

- In the event that the service station is not available, if it is determined that the

repair of the defect is not possible with the report prepared (in order) by one of

the seller, dealer, agency, representative, importer or manufacturer, a refund or a

price discount at the rate of defect can be requested.

20-The customer can make complaints and appeals to consumer courts or

consumer arbitration committees.

21-The warranty document must be kept by the customer during the warranty

period. If the document is lost, a second document will not be issued. In case of

loss, repair and replacement of devices and apparatus will be made for a fee.

TEMPERATURE (ºC) Desired Temperature TPI Room Thermostat

Time

COM

(230V)

HEATING UNIT