GENERAL LIFE HT300 User manual

Screen Indicators
ROOM THERMOSTAT PLACEMENT
Room thermostat needs to placed in the room which is used most
frequently.For instance; living room or lounge.Placing the room
thermostat in a spot that have air circulation like entrance of a room
or side of window should be avoided.Also anywhere close to heating
units such as radiator,stove and spots which get direct sun light
would not be suitable place.Room thermostat needs to be located
above the floor between 50 cm – 150 cm height.Few trials may be
made to find the most convenient spot.
BATTERY PLACEMENT
Remove your room thermostat from Wall hanger. Then remove the
battery housing from the back side of thermostat. Put 2 alkaline
batteries in to battery housing. Please be sure about the directions of
batteries. Hang your thermostat on the Wall hanger after assemble
battery housing back. Change the both batteries together.
GENERAL SPECIFICATIONS
HT300 is a wired room thermostat. The user can adjust the room
thermostat with the required temperature and get more comfortable
and economic heating.
Daily and Weekly Program (7x24)
Different Mode Options (Comfort, Economy, Holiday)
Sensitive temperature measuring ON/OFF Control
Heating calibration Wired Connection
HT300 AND EQUIPMENTS
TECHNICAL DATA
ROOM THERMOSTAT
Buttons Functions
Warning: When the product is not used for a long time (more than 15
days), remove the batteries. Otherwise, malfunctions that will occur
are out of warranty.
Warning!
Please throw away dead batteries to trashes which specially made for
batteries.
THERMOSTAT WIRING DIAGRAM
Warning!
Only people who have got Professional Competence should make
operations of electric wiring or boiler setup.
ROOM THERMOSTAT HEATING CALIBRATION
Temperature sensors which are used in room thermostats, are highly
sensitive. No other thermometers in your living area have that much
sensitivity. so you may need to calibrate your room thermostat if you
would like to get the same temperature degrees with other
thermometers in your living space.
When the device has ''Off '' status ''On/''Off'' button needs to be
pressed for 3 seconds.
 From the calibration menu which appeared, you may set to any
temperature degree by pressing ''Adjustment Buttons''.This value
o o
can be arranged between ''-8 C and +8 C''
 To exit calibration menu please press ''On/Off' button once.
o
Note: Recommended tempreture calibration is “0.0 C”.
KEY LOCK
In room thermostat there is a key lock function to avoid any
unintended contact.
In order to unlock the thermostat's key lock '' Mode'' button should
be pressed for 3 seconds.If buttons on thermostat are not touched
for 10 seconds,key lock will be reactivated.
DAY AND HOUR SETTINGS
While your thermostat is On,keep pressing ''Settings'' button for 3
seconds.
At the first screen that appears ''Hour'' part will be blinking. You may
set the time with 'Up' and 'Down' buttons.
After set the time, ''Settings'' button needs to be pressed once. For
minute setting, minute part will be blinking. You may set the minute
with 'Up' and 'Down' buttons.
After set the minute, “Settings” button needs to be pressed once to
set the day of week.
Days of every week begins with Monday so if you see 1 on the
screen it means Monday is chosen. Likewise 2 would be Tuesday,
3-Wednesday, 4-Thursday, 5-Friday, 6-Saturday and 7-Sunday.
When setting is done you may exit by pressing for 3 seconds to
''Settings'' button.
1
2
3
4
5
6
7
8
9
10
11
12
13
CSet Temperature
Program Mode
Comfort Mode
Economy Mode
Holiday Mode
Manuel Mode
Day Indicator
Hour Indicator
Battery Indicator
Boiler Operates
Screen Lock
Room Temperature
Hours of Day
OC
C
OC
1
2
3
4
5
6
7
9
10
11
813
12
1 2
85mm / 119.5mm / 24mm
3V DC (2 x AAA alkaline battery)
o
0.1 C
o
0.5 C
o o
(5 C) – (30 C)
1 Year (2 x AAA)
o o
(-10 C) – (+50 C)
o o
(-20 C) – (+60 C)
Dimensions
Operating Current
Temperature Measurement Accuracy
Operating Sensitivity
Operating Temperature Range
Battery Life
Operating Temperature
Storage Temperature
50 cm-150 cm
min.50 cm
ENGLISH
HT300 USER MANUAL
generallife.com.tr
DIGITAL ROOM THERMOSTAT
3
1
2
3
4
5
6
1
2
3
4
5
6
Weekly Program Button
Temperature Adjustment (To Increase)
Settings Button
Temperature Adjustment(To Decrease)
Mode Button
On/Off Button
HT300 Room Thermostat Wall Hanger
Alkaline Battery
DIGITAL ROOM THERMOSTAT
HT300
USER MANUAL
generallife.com.tr
THERMOSTAT OUT
COM
NO
AAA AAA
Threaded Inserts and Screws

Screen Indicators
ROOM THERMOSTAT PLACEMENT
Room thermostat needs to placed in the room which is used most
frequently.For instance; living room or lounge.Placing the room
thermostat in a spot that have air circulation like entrance of a room
or side of window should be avoided.Also anywhere close to heating
units such as radiator,stove and spots which get direct sun light
would not be suitable place.Room thermostat needs to be located
above the floor between 50 cm – 150 cm height.Few trials may be
made to find the most convenient spot.
BATTERY PLACEMENT
Remove your room thermostat from Wall hanger. Then remove the
battery housing from the back side of thermostat. Put 2 alkaline
batteries in to battery housing. Please be sure about the directions of
batteries. Hang your thermostat on the Wall hanger after assemble
battery housing back. Change the both batteries together.
GENERAL SPECIFICATIONS
HT300 is a wired room thermostat. The user can adjust the room
thermostat with the required temperature and get more comfortable
and economic heating.
Daily and Weekly Program (7x24)
Different Mode Options (Comfort, Economy, Holiday)
Sensitive temperature measuring ON/OFF Control
Heating calibration Wired Connection
HT300 AND EQUIPMENTS
TECHNICAL DATA
ROOM THERMOSTAT
Buttons Functions
Warning: When the product is not used for a long time (more than 15
days), remove the batteries. Otherwise, malfunctions that will occur
are out of warranty.
Warning!
Please throw away dead batteries to trashes which specially made for
batteries.
THERMOSTAT WIRING DIAGRAM
Warning!
Only people who have got Professional Competence should make
operations of electric wiring or boiler setup.
ROOM THERMOSTAT HEATING CALIBRATION
Temperature sensors which are used in room thermostats, are highly
sensitive. No other thermometers in your living area have that much
sensitivity. so you may need to calibrate your room thermostat if you
would like to get the same temperature degrees with other
thermometers in your living space.
When the device has ''Off '' status ''On/''Off'' button needs to be
pressed for 3 seconds.
 From the calibration menu which appeared, you may set to any
temperature degree by pressing ''Adjustment Buttons''.This value
o o
can be arranged between ''-8 C and +8 C''
 To exit calibration menu please press ''On/Off' button once.
o
Note: Recommended tempreture calibration is “0.0 C”.
KEY LOCK
In room thermostat there is a key lock function to avoid any
unintended contact.
In order to unlock the thermostat's key lock '' Mode'' button should
be pressed for 3 seconds.If buttons on thermostat are not touched
for 10 seconds,key lock will be reactivated.
DAY AND HOUR SETTINGS
While your thermostat is On,keep pressing ''Settings'' button for 3
seconds.
At the first screen that appears ''Hour'' part will be blinking. You may
set the time with 'Up' and 'Down' buttons.
After set the time, ''Settings'' button needs to be pressed once. For
minute setting, minute part will be blinking. You may set the minute
with 'Up' and 'Down' buttons.
After set the minute, “Settings” button needs to be pressed once to
set the day of week.
Days of every week begins with Monday so if you see 1 on the
screen it means Monday is chosen. Likewise 2 would be Tuesday,
3-Wednesday, 4-Thursday, 5-Friday, 6-Saturday and 7-Sunday.
When setting is done you may exit by pressing for 3 seconds to
''Settings'' button.
1
2
3
4
5
6
7
8
9
10
11
12
13
CSet Temperature
Program Mode
Comfort Mode
Economy Mode
Holiday Mode
Manuel Mode
Day Indicator
Hour Indicator
Battery Indicator
Boiler Operates
Screen Lock
Room Temperature
Hours of Day
OC
C
OC
1
2
3
4
5
6
7
9
10
11
813
12
1 2
85mm / 119.5mm / 24mm
3V DC (2 x AAA alkaline battery)
o
0.1 C
o
0.5 C
o o
(5 C) – (30 C)
1 Year (2 x AAA)
o o
(-10 C) – (+50 C)
o o
(-20 C) – (+60 C)
Dimensions
Operating Current
Temperature Measurement Accuracy
Operating Sensitivity
Operating Temperature Range
Battery Life
Operating Temperature
Storage Temperature
50 cm-150 cm
min.50 cm
ENGLISH
HT300 USER MANUAL
generallife.com.tr
DIGITAL ROOM THERMOSTAT
3
1
2
3
4
5
6
1
2
3
4
5
6
Weekly Program Button
Temperature Adjustment (To Increase)
Settings Button
Temperature Adjustment(To Decrease)
Mode Button
On/Off Button
HT300 Room Thermostat Wall Hanger
Alkaline Battery
DIGITAL ROOM THERMOSTAT
HT300
USER MANUAL
generallife.com.tr
THERMOSTAT OUT
COM
NO
AAA AAA
Threaded Inserts and Screws

Screen Indicators
ROOM THERMOSTAT PLACEMENT
Room thermostat needs to placed in the room which is used most
frequently.For instance; living room or lounge.Placing the room
thermostat in a spot that have air circulation like entrance of a room
or side of window should be avoided.Also anywhere close to heating
units such as radiator,stove and spots which get direct sun light
would not be suitable place.Room thermostat needs to be located
above the floor between 50 cm – 150 cm height.Few trials may be
made to find the most convenient spot.
BATTERY PLACEMENT
Remove your room thermostat from Wall hanger. Then remove the
battery housing from the back side of thermostat. Put 2 alkaline
batteries in to battery housing. Please be sure about the directions of
batteries. Hang your thermostat on the Wall hanger after assemble
battery housing back. Change the both batteries together.
GENERAL SPECIFICATIONS
HT300 is a wired room thermostat. The user can adjust the room
thermostat with the required temperature and get more comfortable
and economic heating.
Daily and Weekly Program (7x24)
Different Mode Options (Comfort, Economy, Holiday)
Sensitive temperature measuring ON/OFF Control
Heating calibration Wired Connection
HT300 AND EQUIPMENTS
TECHNICAL DATA
ROOM THERMOSTAT
Buttons Functions
Warning: When the product is not used for a long time (more than 15
days), remove the batteries. Otherwise, malfunctions that will occur
are out of warranty.
Warning!
Please throw away dead batteries to trashes which specially made for
batteries.
THERMOSTAT WIRING DIAGRAM
Warning!
Only people who have got Professional Competence should make
operations of electric wiring or boiler setup.
ROOM THERMOSTAT HEATING CALIBRATION
Temperature sensors which are used in room thermostats, are highly
sensitive. No other thermometers in your living area have that much
sensitivity. so you may need to calibrate your room thermostat if you
would like to get the same temperature degrees with other
thermometers in your living space.
When the device has ''Off '' status ''On/''Off'' button needs to be
pressed for 3 seconds.
 From the calibration menu which appeared, you may set to any
temperature degree by pressing ''Adjustment Buttons''.This value
o o
can be arranged between ''-8 C and +8 C''
 To exit calibration menu please press ''On/Off' button once.
o
Note: Recommended tempreture calibration is “0.0 C”.
KEY LOCK
In room thermostat there is a key lock function to avoid any
unintended contact.
In order to unlock the thermostat's key lock '' Mode'' button should
be pressed for 3 seconds.If buttons on thermostat are not touched
for 10 seconds,key lock will be reactivated.
DAY AND HOUR SETTINGS
While your thermostat is On,keep pressing ''Settings'' button for 3
seconds.
At the first screen that appears ''Hour'' part will be blinking. You may
set the time with 'Up' and 'Down' buttons.
After set the time, ''Settings'' button needs to be pressed once. For
minute setting, minute part will be blinking. You may set the minute
with 'Up' and 'Down' buttons.
After set the minute, “Settings” button needs to be pressed once to
set the day of week.
Days of every week begins with Monday so if you see 1 on the
screen it means Monday is chosen. Likewise 2 would be Tuesday,
3-Wednesday, 4-Thursday, 5-Friday, 6-Saturday and 7-Sunday.
When setting is done you may exit by pressing for 3 seconds to
''Settings'' button.
1
2
3
4
5
6
7
8
9
10
11
12
13
CSet Temperature
Program Mode
Comfort Mode
Economy Mode
Holiday Mode
Manuel Mode
Day Indicator
Hour Indicator
Battery Indicator
Boiler Operates
Screen Lock
Room Temperature
Hours of Day
OC
C
OC
1
2
3
4
5
6
7
9
10
11
813
12
1 2
85mm / 119.5mm / 24mm
3V DC (2 x AAA alkaline battery)
o
0.1 C
o
0.5 C
o o
(5 C) – (30 C)
1 Year (2 x AAA)
o o
(-10 C) – (+50 C)
o o
(-20 C) – (+60 C)
Dimensions
Operating Current
Temperature Measurement Accuracy
Operating Sensitivity
Operating Temperature Range
Battery Life
Operating Temperature
Storage Temperature
50 cm-150 cm
min.50 cm
ENGLISH
HT300 USER MANUAL
generallife.com.tr
DIGITAL ROOM THERMOSTAT
3
1
2
3
4
5
6
1
2
3
4
5
6
Weekly Program Button
Temperature Adjustment (To Increase)
Settings Button
Temperature Adjustment(To Decrease)
Mode Button
On/Off Button
HT300 Room Thermostat Wall Hanger
Alkaline Battery
DIGITAL ROOM THERMOSTAT
HT300
USER MANUAL
generallife.com.tr
THERMOSTAT OUT
COM
NO
AAA AAA
Threaded Inserts and Screws

Screen Indicators
ROOM THERMOSTAT PLACEMENT
Room thermostat needs to placed in the room which is used most
frequently.For instance; living room or lounge.Placing the room
thermostat in a spot that have air circulation like entrance of a room
or side of window should be avoided.Also anywhere close to heating
units such as radiator,stove and spots which get direct sun light
would not be suitable place.Room thermostat needs to be located
above the floor between 50 cm – 150 cm height.Few trials may be
made to find the most convenient spot.
BATTERY PLACEMENT
Remove your room thermostat from Wall hanger. Then remove the
battery housing from the back side of thermostat. Put 2 alkaline
batteries in to battery housing. Please be sure about the directions of
batteries. Hang your thermostat on the Wall hanger after assemble
battery housing back. Change the both batteries together.
GENERAL SPECIFICATIONS
HT300 is a wired room thermostat. The user can adjust the room
thermostat with the required temperature and get more comfortable
and economic heating.
Daily and Weekly Program (7x24)
Different Mode Options (Comfort, Economy, Holiday)
Sensitive temperature measuring ON/OFF Control
Heating calibration Wired Connection
HT300 AND EQUIPMENTS
TECHNICAL DATA
ROOM THERMOSTAT
Buttons Functions
Warning: When the product is not used for a long time (more than 15
days), remove the batteries. Otherwise, malfunctions that will occur
are out of warranty.
Warning!
Please throw away dead batteries to trashes which specially made for
batteries.
THERMOSTAT WIRING DIAGRAM
Warning!
Only people who have got Professional Competence should make
operations of electric wiring or boiler setup.
ROOM THERMOSTAT HEATING CALIBRATION
Temperature sensors which are used in room thermostats, are highly
sensitive. No other thermometers in your living area have that much
sensitivity. so you may need to calibrate your room thermostat if you
would like to get the same temperature degrees with other
thermometers in your living space.
When the device has ''Off '' status ''On/''Off'' button needs to be
pressed for 3 seconds.
 From the calibration menu which appeared, you may set to any
temperature degree by pressing ''Adjustment Buttons''.This value
o o
can be arranged between ''-8 C and +8 C''
 To exit calibration menu please press ''On/Off' button once.
o
Note: Recommended tempreture calibration is “0.0 C”.
KEY LOCK
In room thermostat there is a key lock function to avoid any
unintended contact.
In order to unlock the thermostat's key lock '' Mode'' button should
be pressed for 3 seconds.If buttons on thermostat are not touched
for 10 seconds,key lock will be reactivated.
DAY AND HOUR SETTINGS
While your thermostat is On,keep pressing ''Settings'' button for 3
seconds.
At the first screen that appears ''Hour'' part will be blinking. You may
set the time with 'Up' and 'Down' buttons.
After set the time, ''Settings'' button needs to be pressed once. For
minute setting, minute part will be blinking. You may set the minute
with 'Up' and 'Down' buttons.
After set the minute, “Settings” button needs to be pressed once to
set the day of week.
Days of every week begins with Monday so if you see 1 on the
screen it means Monday is chosen. Likewise 2 would be Tuesday,
3-Wednesday, 4-Thursday, 5-Friday, 6-Saturday and 7-Sunday.
When setting is done you may exit by pressing for 3 seconds to
''Settings'' button.
1
2
3
4
5
6
7
8
9
10
11
12
13
CSet Temperature
Program Mode
Comfort Mode
Economy Mode
Holiday Mode
Manuel Mode
Day Indicator
Hour Indicator
Battery Indicator
Boiler Operates
Screen Lock
Room Temperature
Hours of Day
OC
C
OC
1
2
3
4
5
6
7
9
10
11
813
12
1 2
85mm / 119.5mm / 24mm
3V DC (2 x AAA alkaline battery)
o
0.1 C
o
0.5 C
o o
(5 C) – (30 C)
1 Year (2 x AAA)
o o
(-10 C) – (+50 C)
o o
(-20 C) – (+60 C)
Dimensions
Operating Current
Temperature Measurement Accuracy
Operating Sensitivity
Operating Temperature Range
Battery Life
Operating Temperature
Storage Temperature
50 cm-150 cm
min.50 cm
ENGLISH
HT300 USER MANUAL
generallife.com.tr
DIGITAL ROOM THERMOSTAT
3
1
2
3
4
5
6
1
2
3
4
5
6
Weekly Program Button
Temperature Adjustment (To Increase)
Settings Button
Temperature Adjustment(To Decrease)
Mode Button
On/Off Button
HT300 Room Thermostat Wall Hanger
Alkaline Battery
DIGITAL ROOM THERMOSTAT
HT300
USER MANUAL
generallife.com.tr
THERMOSTAT OUT
COM
NO
AAA AAA
Threaded Inserts and Screws

MODE SETTINGS
Your room thermostat has got 5 different modes. 3 of
them(Comfort,Economy and Holiday Mode) are prepared and
constant modes.Other modes are manual mode and weekly program
mode.
In prepared modes ,temperature degrees are based on user's choices
which has been set in the beginning. Manual mode provides to
operate the thermostat with temperature which user's required and
set directly. Weekly program mode provides to keep operate the
thermostat with weekly program which user's set.
Temperature degrees of prepared modes can be changed on
''Settings'' menu.
In order to go to ''Settings'' menu,''Settings'' button needs to be
pressed for 3 seconds.Date and time settings would appear in first
screen,to skip it ''Settings'' button should be pressed for 3 times.
Comfort Mode's temperature degree would appear and
temperature for Comfort Mode can be adjusted by pressing ''Up''
and ''Down'' buttons.
When setting is done, by pressing ''Settings'' button other modes
(Economy and Holiday Mode) can be set.
Pressing ''Settings'' button for 3 seconds again would close
'Settings' screen.
Manual mode temperature can be set by pressing ''Up'' and ''Down''
buttons while on home screen.
When ''Up'' or ''Down'' buttons are pressed thermostat will be set on
Manual Mode.
In order to change to Mode settings you may press ''Mode'' button.
PROGRAM MODE
You can adjust the weekly operating modes of your room thermostat
seperately for each hours per day under favour of weekly program.
Weekly program mode includes 2 active modes. They are “Comfort
Mode” and “Economy Mode”
In order to arrange the weekly program ''Program Mode” button
needs to be pressed for 3 seconds. On the screen there will be icons
for the day which wants to be programmed,hours of the day and
active mode. The hour which will be programmed will be blinking.
By pressing ''Mode'' button, chosen mode for that specific hour may
be changed.
''Up'' and ''down'' button would allow you to change the chosen time
frame and up to the active it can be programmed.
While setting the weekly program to change the date ''Settings''
button should be pressed.
When weekly program is chosen on screen or while setting weekly
program, if the hours on the screen is blinking, it means that the
chosen hours set on ''Comfort'' mode. If the hour is not blinking then
chosen mode is ''Economy''mode. As for blinking hour means active
current time.
After scheduling the weekly program to register it ''Program Mode'
button needs to be pressed for 3 seconds.
MODES
READY MODES WEEKLY
PROGRAM
MODE
MANUAL MODE
Comfort
Mode Economy Mode Holiday Mode
WARRANTY CONDITIONS
1- Warranty starts at the delivery date of devices and equpments and
warranted against manufacturing defect for 2 years.
2-Devices and equipments are delivered to customers in operation.
Mounting and other connections will be additional fee for service.
3- Devices will maintenance and repair in our factory and should send by
contracted transportation company. For out services, transportation and
accommodation of service personnel are covered by customers. Overtime
is added on service charge and is received as cash proceeds.
4- Maintenance of devices and equipments will be in our factory. For
device maintenance, the round travel fares are covered by customers.
5- If devices are malfunction in warranty duration, devices will be
inspected in our factory to find out whose responsibility (manufacturer or
customer) and will announce to user by report.
6- Devices, which malfunctioned in warranty duration and found out it is
responsibility of manufacturer, customer can demand new product or
repair which all costs will fulfilled by manufacturer regarding to cost is not
higher than device.
7- After inspection of malfunction and detected that, it is customer's fault,
repair cost of the device which still in warranty duration will be customer's
responsibility.
8- Customers should be aware of damages (if there is any) of product and
warn manufacturer since the day warranty duration starts. If customer do
not warn manufacturer with knowledge of damage, customer lose the
rights of article 6.
9- Devices and equipments should be used as specified in User's Manual if
not used as specified, products are out of warranty.
10- If products damaged, scratched or cracked by customer. The products
will be out of warranty conditions.
11- Damages/Malfunctions because of using other brand' s and model' s
devices and equipments without knowledge of manufacturer are out of
warranty.
12- Failures due to battery leakage and acidic / damp conditions and rust,
oxidation and liquid contact are out of warranty.
13- When the product is not used for a long time (more than 15 days),
remove the batteries. Otherwise, malfunctions that will occur are out of
warranty.
14- The transport damage is out of warranty. Customers can take a
transportation insurance.
15- Damages by virtue of grid voltage are out of warranty.
16- Damages because of force majeure like flood, earthquake, fire etc. are
out of warranty.
17- All parts of the product are under warranty of our company.
18- If product breaks down and gets fixed in warranty duration, duration of
maintenance adds to the warranty duration. Products repairment can't
exceed 20 work days. This duration starts when the product's problems are
reported to the seller, agency, producer or the importer if there is no service
station. Consumer can report the problem by; fax, e-mail, registered and
reply paid letter or a similar way. If a conflict happens, the consumer has
the responsibility of proofing it. If the problem can't be solved more than 10
days the producer or importer has to supply a similar device until end of the
reparation. If the product breaks down because of material, label or
mounting faults in the warranty duration, firm won't demand label costs,
changing parts or any other kind of charge for repairment.
19- Despite consumers rights of maintenance;
- If the product breaks down for 4 times in a year or 6 times in warranty
duration and these problems effects main purpose of the product.
(starting from delivery time during warranty.),
- Exceeding the maximum repairing term,
- In the case of not existing service station, determining that repairment is
not possible with the report compiled by respectively service station's
seller, dealer, agency, legation, importer or manufacturer.
20- You may apply for Ministry of Custom and Trade and General
Directorate of Protection of Costumers and Market Surveillance in case of
the problems about certificate of warranty.
21- Warranty document should be kept by customer until warranty
duration is finished. If warranty is lost there will be no replacement. All
maintance and repair cost is responsibility of customer in case of warranty
document lost.
DECLARATION OF CONFORMITY
ISIPARK İÇ VE DIŞ TİC. İNŞ. ISITMA SİSTEMLERİ OTO. SAN.A.Ş.which
Head Office and production site is located on Fatih Mah. 1188
Sk.No:13/A Sarnıç - Gaziemir - İZMİR – TÜRKİYE confirms and
declares that the product marked with CE and its specifications below
is covered by the provisions of the mentioned directive.
Brand
Product Name
Product Type
Compatible Directives:
Radio and Telecommunications Terminal Equipment Regulation
2014/53/EU (R&TTE/RED EN 301 489-1 V2.1.1:2017, EN 300 220-
1V3.1.1:2017, EN 301 489-3 V2.1.1:2017, EN 300 220-2 V3.1.1:2017,
EN 62479: 2010, EN 60730-2-9:2010, EN 60730-1:2011)
Electromagnetic Compatibility Regulation 2014/30/EU (EMC EN
61000-6-3: 2007 + A1: 2011, EN 61000-6-1: 2007
Low Voltage Directive 2014/35/EU (LVD EN 60730-2-9:2010, EN
60730-1:2011)
Supplementary Information: Mentioned product can be used with
combi boilers with on / off output and compatibility with the directive
only covers the product. ISIPARK is not responsible for the
compliance of the entire system with the directive. This declaration
does not apply when changes are made to the product without
obtaining our consent.
4
: GENERAL Life
: HT300
: Digital Room Thermostat
5 6
Manufacturer
Title: ISIPARK İÇ DIŞ TİC. A.Ş.
Adsress: Fatih Mah. 1188 Sk. No:13/A Sarnıç
Gaziemir İzmir-TÜRKİYE
Tel: [phone]
Fax: [phone]
E-Mail: [e-mail]
Authorised Signatory:
Company Stamp:
Product
Type: Digital Room Thermostat
Brand: GENERAL Life
Model: HT300
Guarantee Period: 2 Years
Max. Time to Repair: 20 Days
Banderole and Serial Number:
Vendor
Title:
Address:
Tel: Fax:
E-Mail: Invoice Date and Number:
Delivery Time and Place:
Authorised Signatory:
Company Stamp:
Product
Type: Digital Room Thermostat
Brand: GENERAL Life
Model: HT300 STAMP
WARRANTY CERTIFICATE
Isıpark reserves the rights of changing product specifications and
user manuals.
*For all changes,you may visit generallife.com.tr

MODE SETTINGS
Your room thermostat has got 5 different modes. 3 of
them(Comfort,Economy and Holiday Mode) are prepared and
constant modes.Other modes are manual mode and weekly program
mode.
In prepared modes ,temperature degrees are based on user's choices
which has been set in the beginning. Manual mode provides to
operate the thermostat with temperature which user's required and
set directly. Weekly program mode provides to keep operate the
thermostat with weekly program which user's set.
Temperature degrees of prepared modes can be changed on
''Settings'' menu.
In order to go to ''Settings'' menu,''Settings'' button needs to be
pressed for 3 seconds.Date and time settings would appear in first
screen,to skip it ''Settings'' button should be pressed for 3 times.
Comfort Mode's temperature degree would appear and
temperature for Comfort Mode can be adjusted by pressing ''Up''
and ''Down'' buttons.
When setting is done, by pressing ''Settings'' button other modes
(Economy and Holiday Mode) can be set.
Pressing ''Settings'' button for 3 seconds again would close
'Settings' screen.
Manual mode temperature can be set by pressing ''Up'' and ''Down''
buttons while on home screen.
When ''Up'' or ''Down'' buttons are pressed thermostat will be set on
Manual Mode.
In order to change to Mode settings you may press ''Mode'' button.
PROGRAM MODE
You can adjust the weekly operating modes of your room thermostat
seperately for each hours per day under favour of weekly program.
Weekly program mode includes 2 active modes. They are “Comfort
Mode” and “Economy Mode”
In order to arrange the weekly program ''Program Mode” button
needs to be pressed for 3 seconds. On the screen there will be icons
for the day which wants to be programmed,hours of the day and
active mode. The hour which will be programmed will be blinking.
By pressing ''Mode'' button, chosen mode for that specific hour may
be changed.
''Up'' and ''down'' button would allow you to change the chosen time
frame and up to the active it can be programmed.
While setting the weekly program to change the date ''Settings''
button should be pressed.
When weekly program is chosen on screen or while setting weekly
program, if the hours on the screen is blinking, it means that the
chosen hours set on ''Comfort'' mode. If the hour is not blinking then
chosen mode is ''Economy''mode. As for blinking hour means active
current time.
After scheduling the weekly program to register it ''Program Mode'
button needs to be pressed for 3 seconds.
MODES
READY MODES WEEKLY
PROGRAM
MODE
MANUAL MODE
Comfort
Mode Economy Mode Holiday Mode
WARRANTY CONDITIONS
1- Warranty starts at the delivery date of devices and equpments and
warranted against manufacturing defect for 2 years.
2-Devices and equipments are delivered to customers in operation.
Mounting and other connections will be additional fee for service.
3- Devices will maintenance and repair in our factory and should send by
contracted transportation company. For out services, transportation and
accommodation of service personnel are covered by customers. Overtime
is added on service charge and is received as cash proceeds.
4- Maintenance of devices and equipments will be in our factory. For
device maintenance, the round travel fares are covered by customers.
5- If devices are malfunction in warranty duration, devices will be
inspected in our factory to find out whose responsibility (manufacturer or
customer) and will announce to user by report.
6- Devices, which malfunctioned in warranty duration and found out it is
responsibility of manufacturer, customer can demand new product or
repair which all costs will fulfilled by manufacturer regarding to cost is not
higher than device.
7- After inspection of malfunction and detected that, it is customer's fault,
repair cost of the device which still in warranty duration will be customer's
responsibility.
8- Customers should be aware of damages (if there is any) of product and
warn manufacturer since the day warranty duration starts. If customer do
not warn manufacturer with knowledge of damage, customer lose the
rights of article 6.
9- Devices and equipments should be used as specified in User's Manual if
not used as specified, products are out of warranty.
10- If products damaged, scratched or cracked by customer. The products
will be out of warranty conditions.
11- Damages/Malfunctions because of using other brand' s and model' s
devices and equipments without knowledge of manufacturer are out of
warranty.
12- Failures due to battery leakage and acidic / damp conditions and rust,
oxidation and liquid contact are out of warranty.
13- When the product is not used for a long time (more than 15 days),
remove the batteries. Otherwise, malfunctions that will occur are out of
warranty.
14- The transport damage is out of warranty. Customers can take a
transportation insurance.
15- Damages by virtue of grid voltage are out of warranty.
16- Damages because of force majeure like flood, earthquake, fire etc. are
out of warranty.
17- All parts of the product are under warranty of our company.
18- If product breaks down and gets fixed in warranty duration, duration of
maintenance adds to the warranty duration. Products repairment can't
exceed 20 work days. This duration starts when the product's problems are
reported to the seller, agency, producer or the importer if there is no service
station. Consumer can report the problem by; fax, e-mail, registered and
reply paid letter or a similar way. If a conflict happens, the consumer has
the responsibility of proofing it. If the problem can't be solved more than 10
days the producer or importer has to supply a similar device until end of the
reparation. If the product breaks down because of material, label or
mounting faults in the warranty duration, firm won't demand label costs,
changing parts or any other kind of charge for repairment.
19- Despite consumers rights of maintenance;
- If the product breaks down for 4 times in a year or 6 times in warranty
duration and these problems effects main purpose of the product.
(starting from delivery time during warranty.),
- Exceeding the maximum repairing term,
- In the case of not existing service station, determining that repairment is
not possible with the report compiled by respectively service station's
seller, dealer, agency, legation, importer or manufacturer.
20- You may apply for Ministry of Custom and Trade and General
Directorate of Protection of Costumers and Market Surveillance in case of
the problems about certificate of warranty.
21- Warranty document should be kept by customer until warranty
duration is finished. If warranty is lost there will be no replacement. All
maintance and repair cost is responsibility of customer in case of warranty
document lost.
DECLARATION OF CONFORMITY
ISIPARK İÇ VE DIŞ TİC. İNŞ. ISITMA SİSTEMLERİ OTO. SAN.A.Ş.which
Head Office and production site is located on Fatih Mah. 1188
Sk.No:13/A Sarnıç - Gaziemir - İZMİR – TÜRKİYE confirms and
declares that the product marked with CE and its specifications below
is covered by the provisions of the mentioned directive.
Brand
Product Name
Product Type
Compatible Directives:
Radio and Telecommunications Terminal Equipment Regulation
2014/53/EU (R&TTE/RED EN 301 489-1 V2.1.1:2017, EN 300 220-
1V3.1.1:2017, EN 301 489-3 V2.1.1:2017, EN 300 220-2 V3.1.1:2017,
EN 62479: 2010, EN 60730-2-9:2010, EN 60730-1:2011)
Electromagnetic Compatibility Regulation 2014/30/EU (EMC EN
61000-6-3: 2007 + A1: 2011, EN 61000-6-1: 2007
Low Voltage Directive 2014/35/EU (LVD EN 60730-2-9:2010, EN
60730-1:2011)
Supplementary Information: Mentioned product can be used with
combi boilers with on / off output and compatibility with the directive
only covers the product. ISIPARK is not responsible for the
compliance of the entire system with the directive. This declaration
does not apply when changes are made to the product without
obtaining our consent.
4
: GENERAL Life
: HT300
: Digital Room Thermostat
5 6
Manufacturer
Title: ISIPARK İÇ DIŞ TİC. A.Ş.
Adsress: Fatih Mah. 1188 Sk. No:13/A Sarnıç
Gaziemir İzmir-TÜRKİYE
Tel: [phone]
Fax: [phone]
E-Mail: [e-mail]
Authorised Signatory:
Company Stamp:
Product
Type: Digital Room Thermostat
Brand: GENERAL Life
Model: HT300
Guarantee Period: 2 Years
Max. Time to Repair: 20 Days
Banderole and Serial Number:
Vendor
Title:
Address:
Tel: Fax:
E-Mail: Invoice Date and Number:
Delivery Time and Place:
Authorised Signatory:
Company Stamp:
Product
Type: Digital Room Thermostat
Brand: GENERAL Life
Model: HT300 STAMP
WARRANTY CERTIFICATE
Isıpark reserves the rights of changing product specifications and
user manuals.
*For all changes,you may visit generallife.com.tr

MODE SETTINGS
Your room thermostat has got 5 different modes. 3 of
them(Comfort,Economy and Holiday Mode) are prepared and
constant modes.Other modes are manual mode and weekly program
mode.
In prepared modes ,temperature degrees are based on user's choices
which has been set in the beginning. Manual mode provides to
operate the thermostat with temperature which user's required and
set directly. Weekly program mode provides to keep operate the
thermostat with weekly program which user's set.
Temperature degrees of prepared modes can be changed on
''Settings'' menu.
In order to go to ''Settings'' menu,''Settings'' button needs to be
pressed for 3 seconds.Date and time settings would appear in first
screen,to skip it ''Settings'' button should be pressed for 3 times.
Comfort Mode's temperature degree would appear and
temperature for Comfort Mode can be adjusted by pressing ''Up''
and ''Down'' buttons.
When setting is done, by pressing ''Settings'' button other modes
(Economy and Holiday Mode) can be set.
Pressing ''Settings'' button for 3 seconds again would close
'Settings' screen.
Manual mode temperature can be set by pressing ''Up'' and ''Down''
buttons while on home screen.
When ''Up'' or ''Down'' buttons are pressed thermostat will be set on
Manual Mode.
In order to change to Mode settings you may press ''Mode'' button.
PROGRAM MODE
You can adjust the weekly operating modes of your room thermostat
seperately for each hours per day under favour of weekly program.
Weekly program mode includes 2 active modes. They are “Comfort
Mode” and “Economy Mode”
In order to arrange the weekly program ''Program Mode” button
needs to be pressed for 3 seconds. On the screen there will be icons
for the day which wants to be programmed,hours of the day and
active mode. The hour which will be programmed will be blinking.
By pressing ''Mode'' button, chosen mode for that specific hour may
be changed.
''Up'' and ''down'' button would allow you to change the chosen time
frame and up to the active it can be programmed.
While setting the weekly program to change the date ''Settings''
button should be pressed.
When weekly program is chosen on screen or while setting weekly
program, if the hours on the screen is blinking, it means that the
chosen hours set on ''Comfort'' mode. If the hour is not blinking then
chosen mode is ''Economy''mode. As for blinking hour means active
current time.
After scheduling the weekly program to register it ''Program Mode'
button needs to be pressed for 3 seconds.
MODES
READY MODES WEEKLY
PROGRAM
MODE
MANUAL MODE
Comfort
Mode Economy Mode Holiday Mode
WARRANTY CONDITIONS
1- Warranty starts at the delivery date of devices and equpments and
warranted against manufacturing defect for 2 years.
2-Devices and equipments are delivered to customers in operation.
Mounting and other connections will be additional fee for service.
3- Devices will maintenance and repair in our factory and should send by
contracted transportation company. For out services, transportation and
accommodation of service personnel are covered by customers. Overtime
is added on service charge and is received as cash proceeds.
4- Maintenance of devices and equipments will be in our factory. For
device maintenance, the round travel fares are covered by customers.
5- If devices are malfunction in warranty duration, devices will be
inspected in our factory to find out whose responsibility (manufacturer or
customer) and will announce to user by report.
6- Devices, which malfunctioned in warranty duration and found out it is
responsibility of manufacturer, customer can demand new product or
repair which all costs will fulfilled by manufacturer regarding to cost is not
higher than device.
7- After inspection of malfunction and detected that, it is customer's fault,
repair cost of the device which still in warranty duration will be customer's
responsibility.
8- Customers should be aware of damages (if there is any) of product and
warn manufacturer since the day warranty duration starts. If customer do
not warn manufacturer with knowledge of damage, customer lose the
rights of article 6.
9- Devices and equipments should be used as specified in User's Manual if
not used as specified, products are out of warranty.
10- If products damaged, scratched or cracked by customer. The products
will be out of warranty conditions.
11- Damages/Malfunctions because of using other brand' s and model' s
devices and equipments without knowledge of manufacturer are out of
warranty.
12- Failures due to battery leakage and acidic / damp conditions and rust,
oxidation and liquid contact are out of warranty.
13- When the product is not used for a long time (more than 15 days),
remove the batteries. Otherwise, malfunctions that will occur are out of
warranty.
14- The transport damage is out of warranty. Customers can take a
transportation insurance.
15- Damages by virtue of grid voltage are out of warranty.
16- Damages because of force majeure like flood, earthquake, fire etc. are
out of warranty.
17- All parts of the product are under warranty of our company.
18- If product breaks down and gets fixed in warranty duration, duration of
maintenance adds to the warranty duration. Products repairment can't
exceed 20 work days. This duration starts when the product's problems are
reported to the seller, agency, producer or the importer if there is no service
station. Consumer can report the problem by; fax, e-mail, registered and
reply paid letter or a similar way. If a conflict happens, the consumer has
the responsibility of proofing it. If the problem can't be solved more than 10
days the producer or importer has to supply a similar device until end of the
reparation. If the product breaks down because of material, label or
mounting faults in the warranty duration, firm won't demand label costs,
changing parts or any other kind of charge for repairment.
19- Despite consumers rights of maintenance;
- If the product breaks down for 4 times in a year or 6 times in warranty
duration and these problems effects main purpose of the product.
(starting from delivery time during warranty.),
- Exceeding the maximum repairing term,
- In the case of not existing service station, determining that repairment is
not possible with the report compiled by respectively service station's
seller, dealer, agency, legation, importer or manufacturer.
20- You may apply for Ministry of Custom and Trade and General
Directorate of Protection of Costumers and Market Surveillance in case of
the problems about certificate of warranty.
21- Warranty document should be kept by customer until warranty
duration is finished. If warranty is lost there will be no replacement. All
maintance and repair cost is responsibility of customer in case of warranty
document lost.
DECLARATION OF CONFORMITY
ISIPARK İÇ VE DIŞ TİC. İNŞ. ISITMA SİSTEMLERİ OTO. SAN.A.Ş.which
Head Office and production site is located on Fatih Mah. 1188
Sk.No:13/A Sarnıç - Gaziemir - İZMİR – TÜRKİYE confirms and
declares that the product marked with CE and its specifications below
is covered by the provisions of the mentioned directive.
Brand
Product Name
Product Type
Compatible Directives:
Radio and Telecommunications Terminal Equipment Regulation
2014/53/EU (R&TTE/RED EN 301 489-1 V2.1.1:2017, EN 300 220-
1V3.1.1:2017, EN 301 489-3 V2.1.1:2017, EN 300 220-2 V3.1.1:2017,
EN 62479: 2010, EN 60730-2-9:2010, EN 60730-1:2011)
Electromagnetic Compatibility Regulation 2014/30/EU (EMC EN
61000-6-3: 2007 + A1: 2011, EN 61000-6-1: 2007
Low Voltage Directive 2014/35/EU (LVD EN 60730-2-9:2010, EN
60730-1:2011)
Supplementary Information: Mentioned product can be used with
combi boilers with on / off output and compatibility with the directive
only covers the product. ISIPARK is not responsible for the
compliance of the entire system with the directive. This declaration
does not apply when changes are made to the product without
obtaining our consent.
4
: GENERAL Life
: HT300
: Digital Room Thermostat
5 6
Manufacturer
Title: ISIPARK İÇ DIŞ TİC. A.Ş.
Adsress: Fatih Mah. 1188 Sk. No:13/A Sarnıç
Gaziemir İzmir-TÜRKİYE
Tel: [phone]
Fax: [phone]
E-Mail: [e-mail]
Authorised Signatory:
Company Stamp:
Product
Type: Digital Room Thermostat
Brand: GENERAL Life
Model: HT300
Guarantee Period: 2 Years
Max. Time to Repair: 20 Days
Banderole and Serial Number:
Vendor
Title:
Address:
Tel: Fax:
E-Mail: Invoice Date and Number:
Delivery Time and Place:
Authorised Signatory:
Company Stamp:
Product
Type: Digital Room Thermostat
Brand: GENERAL Life
Model: HT300 STAMP
WARRANTY CERTIFICATE
Isıpark reserves the rights of changing product specifications and
user manuals.
*For all changes,you may visit generallife.com.tr

MODE SETTINGS
Your room thermostat has got 5 different modes. 3 of
them(Comfort,Economy and Holiday Mode) are prepared and
constant modes.Other modes are manual mode and weekly program
mode.
In prepared modes ,temperature degrees are based on user's choices
which has been set in the beginning. Manual mode provides to
operate the thermostat with temperature which user's required and
set directly. Weekly program mode provides to keep operate the
thermostat with weekly program which user's set.
Temperature degrees of prepared modes can be changed on
''Settings'' menu.
In order to go to ''Settings'' menu,''Settings'' button needs to be
pressed for 3 seconds.Date and time settings would appear in first
screen,to skip it ''Settings'' button should be pressed for 3 times.
Comfort Mode's temperature degree would appear and
temperature for Comfort Mode can be adjusted by pressing ''Up''
and ''Down'' buttons.
When setting is done, by pressing ''Settings'' button other modes
(Economy and Holiday Mode) can be set.
Pressing ''Settings'' button for 3 seconds again would close
'Settings' screen.
Manual mode temperature can be set by pressing ''Up'' and ''Down''
buttons while on home screen.
When ''Up'' or ''Down'' buttons are pressed thermostat will be set on
Manual Mode.
In order to change to Mode settings you may press ''Mode'' button.
PROGRAM MODE
You can adjust the weekly operating modes of your room thermostat
seperately for each hours per day under favour of weekly program.
Weekly program mode includes 2 active modes. They are “Comfort
Mode” and “Economy Mode”
In order to arrange the weekly program ''Program Mode” button
needs to be pressed for 3 seconds. On the screen there will be icons
for the day which wants to be programmed,hours of the day and
active mode. The hour which will be programmed will be blinking.
By pressing ''Mode'' button, chosen mode for that specific hour may
be changed.
''Up'' and ''down'' button would allow you to change the chosen time
frame and up to the active it can be programmed.
While setting the weekly program to change the date ''Settings''
button should be pressed.
When weekly program is chosen on screen or while setting weekly
program, if the hours on the screen is blinking, it means that the
chosen hours set on ''Comfort'' mode. If the hour is not blinking then
chosen mode is ''Economy''mode. As for blinking hour means active
current time.
After scheduling the weekly program to register it ''Program Mode'
button needs to be pressed for 3 seconds.
MODES
READY MODES WEEKLY
PROGRAM
MODE
MANUAL MODE
Comfort
Mode Economy Mode Holiday Mode
WARRANTY CONDITIONS
1- Warranty starts at the delivery date of devices and equpments and
warranted against manufacturing defect for 2 years.
2-Devices and equipments are delivered to customers in operation.
Mounting and other connections will be additional fee for service.
3- Devices will maintenance and repair in our factory and should send by
contracted transportation company. For out services, transportation and
accommodation of service personnel are covered by customers. Overtime
is added on service charge and is received as cash proceeds.
4- Maintenance of devices and equipments will be in our factory. For
device maintenance, the round travel fares are covered by customers.
5- If devices are malfunction in warranty duration, devices will be
inspected in our factory to find out whose responsibility (manufacturer or
customer) and will announce to user by report.
6- Devices, which malfunctioned in warranty duration and found out it is
responsibility of manufacturer, customer can demand new product or
repair which all costs will fulfilled by manufacturer regarding to cost is not
higher than device.
7- After inspection of malfunction and detected that, it is customer's fault,
repair cost of the device which still in warranty duration will be customer's
responsibility.
8- Customers should be aware of damages (if there is any) of product and
warn manufacturer since the day warranty duration starts. If customer do
not warn manufacturer with knowledge of damage, customer lose the
rights of article 6.
9- Devices and equipments should be used as specified in User's Manual if
not used as specified, products are out of warranty.
10- If products damaged, scratched or cracked by customer. The products
will be out of warranty conditions.
11- Damages/Malfunctions because of using other brand' s and model' s
devices and equipments without knowledge of manufacturer are out of
warranty.
12- Failures due to battery leakage and acidic / damp conditions and rust,
oxidation and liquid contact are out of warranty.
13- When the product is not used for a long time (more than 15 days),
remove the batteries. Otherwise, malfunctions that will occur are out of
warranty.
14- The transport damage is out of warranty. Customers can take a
transportation insurance.
15- Damages by virtue of grid voltage are out of warranty.
16- Damages because of force majeure like flood, earthquake, fire etc. are
out of warranty.
17- All parts of the product are under warranty of our company.
18- If product breaks down and gets fixed in warranty duration, duration of
maintenance adds to the warranty duration. Products repairment can't
exceed 20 work days. This duration starts when the product's problems are
reported to the seller, agency, producer or the importer if there is no service
station. Consumer can report the problem by; fax, e-mail, registered and
reply paid letter or a similar way. If a conflict happens, the consumer has
the responsibility of proofing it. If the problem can't be solved more than 10
days the producer or importer has to supply a similar device until end of the
reparation. If the product breaks down because of material, label or
mounting faults in the warranty duration, firm won't demand label costs,
changing parts or any other kind of charge for repairment.
19- Despite consumers rights of maintenance;
- If the product breaks down for 4 times in a year or 6 times in warranty
duration and these problems effects main purpose of the product.
(starting from delivery time during warranty.),
- Exceeding the maximum repairing term,
- In the case of not existing service station, determining that repairment is
not possible with the report compiled by respectively service station's
seller, dealer, agency, legation, importer or manufacturer.
20- You may apply for Ministry of Custom and Trade and General
Directorate of Protection of Costumers and Market Surveillance in case of
the problems about certificate of warranty.
21- Warranty document should be kept by customer until warranty
duration is finished. If warranty is lost there will be no replacement. All
maintance and repair cost is responsibility of customer in case of warranty
document lost.
DECLARATION OF CONFORMITY
ISIPARK İÇ VE DIŞ TİC. İNŞ. ISITMA SİSTEMLERİ OTO. SAN.A.Ş.which
Head Office and production site is located on Fatih Mah. 1188
Sk.No:13/A Sarnıç - Gaziemir - İZMİR – TÜRKİYE confirms and
declares that the product marked with CE and its specifications below
is covered by the provisions of the mentioned directive.
Brand
Product Name
Product Type
Compatible Directives:
Radio and Telecommunications Terminal Equipment Regulation
2014/53/EU (R&TTE/RED EN 301 489-1 V2.1.1:2017, EN 300 220-
1V3.1.1:2017, EN 301 489-3 V2.1.1:2017, EN 300 220-2 V3.1.1:2017,
EN 62479: 2010, EN 60730-2-9:2010, EN 60730-1:2011)
Electromagnetic Compatibility Regulation 2014/30/EU (EMC EN
61000-6-3: 2007 + A1: 2011, EN 61000-6-1: 2007
Low Voltage Directive 2014/35/EU (LVD EN 60730-2-9:2010, EN
60730-1:2011)
Supplementary Information: Mentioned product can be used with
combi boilers with on / off output and compatibility with the directive
only covers the product. ISIPARK is not responsible for the
compliance of the entire system with the directive. This declaration
does not apply when changes are made to the product without
obtaining our consent.
4
: GENERAL Life
: HT300
: Digital Room Thermostat
5 6
Manufacturer
Title: ISIPARK İÇ DIŞ TİC. A.Ş.
Adsress: Fatih Mah. 1188 Sk. No:13/A Sarnıç
Gaziemir İzmir-TÜRKİYE
Tel: [phone]
Fax: [phone]
E-Mail: [email protected]
Authorised Signatory:
Company Stamp:
Product
Type: Digital Room Thermostat
Brand: GENERAL Life
Model: HT300
Guarantee Period: 2 Years
Max. Time to Repair: 20 Days
Banderole and Serial Number:
Vendor
Title:
Address:
Tel: Fax:
E-Mail: Invoice Date and Number:
Delivery Time and Place:
Authorised Signatory:
Company Stamp:
Product
Type: Digital Room Thermostat
Brand: GENERAL Life
Model: HT300 STAMP
WARRANTY CERTIFICATE
Isıpark reserves the rights of changing product specifications and
user manuals.
*For all changes,you may visit generallife.com.tr