General Pump DCFSCP20 The Hammerhead User manual

PROFESSIONAL FLAT SURFACE CLEANER
DCFSCP20
OPERATOR’S MANUAL
General ump is a
member of
the Interpump Group
WARNING: Read Be ore Operating Machine
Always wear protective eyewear
Keep clear o rotating nozzles
Never lock trigger gun open with any device
Drain water in cold weather to avoid reezing
Tampering with any part of this machine will void all warranties
FROM GENERAL PUMP
• COMPENSATING GUN FEATURE
• FULL 20” CLEANING PATH
• HEAVY-DUTY ANODIZED
ALUMINUM COMPONENTS
• RUGGED ABS COVER
AVAILABLE REPAIR KITS
Rotary Head Kit - Major:
/N 2100279
Includes items 2, 3, 4, 5, 6, 7, 8, 9,
10, 11, 12, 13, 14, 15 and 16
Rotary Head Kit - Minor:
/N 2100203
Includes items 9, 10, 12 and 16
Complete Rotary Head Kit:
/N 2103065
Includes all items
DCG4000 FSC Gun Kit:
/N 2100274
ITEM
NO.
PART
NO. DESCRIPTION QTY.
1 2500004 Housing, Swivel 1
2 2520030 Bearing Retainer, Small 1
3 2520028 Retainer, Bearing 1
4 2520031 Washer, Bearing Retainer 1
5 2520027 Spacer, Bearing 2
6 2640015 Bearing, 15 x 42 2
7 2701012 O-ring 1
8 2701011 O-ring 1
9 2701010 O-ring 1
10 2720007 Spring, Compression 1
11 2530008 in 2
12 2530007 Stem, Small 1
13 2200037 Snap Ring 1
14 2520029 Snap Ring 3
15 2200038 Stem, Swivel 1
16 2710000 Back-up Ring 1

ITEM
NO.
PART
NO. DESCRIPTION
QTY.
1 2103065 Swivel, 20” 1
2 2660045 Deck, G , 20” 1
3 2530009 Arm, Rotary, Assy., 20” 1
4 2630010 late, Retaining 1
5 2540023 Collar, Split 1
6 2200055 SHCS, M8 X 1.25 X 30, SST 4
7 2200054 SHCS, M8 x 1.25 x 25, SST 1
8 2540020 Block, Handle 2
9 2200047 Bolt, M6 8
10 2203406 Washer, M6 8
11 2540021 Handle, Lower 1
12 2540037 Handle, Upper 1
ITEM
NO.
PART
NO. DESCRIPTION
QTY.
13 2660047 Grip, Handle 1
14 2660046 lug, Handle 1
15 2660059 Brush Assy., 20” 1
16 DCG4000FSC Gun, Flat Surface Cleaner 1
17 2702000 Hose, 20” 1
18 2200063 Nut, M8 x 1.25, Nylok, SST 4
19 D10009 lug, 3/9 x 3/8-M 1
20 D10004 Coupler, 3/8 x 3/8-M 1
21 2200028 Nut, Nylok, M6 2
22 2202010 in, 55mm, w/Ring, SST 2
23 2200058 HHCS, M6 X 1 X 60 2
24 2200018 Washer, M6 4
25 2203507 Washer, M6, SST, Lock 1
General Pump
1174 Northland Drive • Mendota Heights, MN 55120
hone: 651.686.2199 • Fax: [phone]
www.generalpump.com • [email protected]
Ref 300748 Rev.A
08-10
Operating ressures: 1,000 to 4,000 SI
Max Flow: 8.0 G M
Dimensions: 70” x 21” x 21”
Weight: 21 lbs.
Operating Instructions
1. Connect to ressure Washer.
2. Turn water on and open valve. Open trigger gun for flow of water
through nozzles. Nozzles must have flowing spray. If not, remove
tips and clean; reassemble, making sure that groove of nozzle is
parallel to spray bar. Use thread sealant when installing nozzles.
3. Start ressure Washer. The Hammerhead is ready for operation.
4. Walk slowly behind the Hammerhead cleaning as you go. If
striping occurs, slow down your pace.
5. eriodically check weep hole on bottom of swivel. Water will
seep slowly; if water shoots out, stop and replace seals. Swivel
assembly can be rebuilt.
6. For maximum effectiveness keep spray tips clean. If the machine
vibrates, stop and clean spray tips.
7. Lubricate swivel with one squirt of good quality grease every 200
hours of operation or about once a month if used daily. A small
amount of grease coming out of the swivel is normal.
DO NOT ALLOW MACHINE TO REMAIN STATIONARY
ON SOFT SURFACES SUCH AS WOOD.
Caution: Striking any raised obstacle during operation will damage
machine. If contact does occur and results in vibration when
operating machine, STO and replace spray bar. Continued
operation could result in serious injury or damage to machine.