Genie CCTV LSM-413 User manual

Copyright @ 2012 by this company. No. Part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system
or translated into any language or computer language, in any form
or any means. Electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of this
company.
I. Security notes
1
The unit is only suitable for indoor use. The heat being generated in the
unit has to be removed via air circulation. Therefore the circulation vents
in the housings must not be covered with any objects. Do not insert or
drop anything into the air vents ! This could result in a short-circuit. If the
unit is used for purposes other than originally intended, if it is connected
in the wrong way or not repaired by authorized skilled personnel, there is
no liability for possible damage. Do not use any fluid, cleaning chemicals
or abrasive materials. If the unit is to be scraped then take it to the local
recycling plant for disposal. We do not accept any liability for the
following : a) If the unit is used for purposes other than originally intended.
B) If The unit is wrongly connected. c) If the unit is not repaired by an
qualified authorized engineer.
II. Application range
The LCD color monitors LSM-413 active matrix technology offer a sharp and
high contrast display. It can be universally used for Surveillance systems,
In-Vehicle Reverse monitoring systems or for Multimedia applications. The
additional Audio input enable sound reception via Headphones.
Page 1 of 6
SAFETY INSTRUCTION
1. Never push objects or spill any liquid of any kind into the unit.
2. Do not attempt to service this product yourself, as opening or
removing covers may expose you to dangerous voltage points or
other risks. Refer all servicing to qualified service personnel, if any
misuse mentioned above happened or any accident dropping,
miss-operations occurred.
3. WARNING : DO NOT USE THE CHARGER TO POWER THE
UNIT.Serious damage will occur which will not be covered by the
warranty.
Page 6 of 6

2
v. Technical Data
LCD technology: TFT active matrix
Display size: 4”
Active area : 82.08 x 61..56 mm
Color system: NTSC or PAL
Sync. :.Horizontal :15, 625 Hz, Vertical : 50 Hz.
Resolution:960 x 240 , 230,400 Pixels
Audio level: 1V/10k
Video Input : 1Vpp 75 Ω
Dimensions ( Bag ) :190.0 (W) x 130.0 (H) x 60 (D) mm
Weight : 1.2 Kg
CAUTION:When using headphones do not adjust the volume to a high position.
Start at the lowest setting and gradually raise it so it can be heard.
The human ear gets accustom to the volume setting, so do not further
increase the volume after getting used to it. Permanent high volumes
can seriously damage your hearing.
Page 5 of 6
I. CONTENTS :
1.4” LCD monitor
2.Carry Bag and Belts
3.1300mA Energy Saving Li-ion Rechargeable Battery
4.Three velcos , two for monitor and one for battery.
5.30 cm power cord.
6.15V DC Charger. This Charger should only be used to
charge the battery NOT to supply the unit. If used on
the unit Serious damage may occur which will not be
covered by the warranty.
7.RCA to BNC adapter 4 pcs.
8.Spacer Protector
II . Power Operating and Connections
1.Please charge the Li-ion Battery for one and half hours
before using it for the first time.
2.Please stick two velcos to the rear of monitor. Then
place the monitor in the correct position in the bag. This
will then fasten the monitor to the bag will restrict any
movement when the bag lid is open.
3.Connect the battery to monitor via the DC power cord
( Supplied).
Page 2 of 6

III. LCD Monitor Operation and Connections :
i. Controls and Connectors on LCD monitor:
1.Brightnesscontrol 2.ColorControl
3. Volume control for headphones 4. Audio output for headphones
3
5.MainPowerswitch 6.Videooutput
7. Audio input 8. Video 1Input
9. Video 2 Input 10. Video Input 1or 2 Switch
11. 12V DC Power Input
ii.. Connections
1) Connect the video source to the Video input 1(8) or Video 2(9) Inputs.
2) Select the correct Video input using the Video Input switch (10).
3) Connect the Audio source to the audio input (7).
4) Connect an electronically regulated 12V power supply
The positive pole must be connected to the center contact.
5) Connect headphones to the Audio Output if required.
Page 3 of 6
iii. Operation
Switch on the monitor using the Main Power switch (5).
1) Adjust the brightness control (1) and color (2) in order to obtain an
image as clear and sharp as possible.
2) Adjust the volume control of the headphones to the desired level.
3) Select the correct Video Input
iv. Energy Saving Li-ion Rechargeable Battery
1) To charge the battery simply push the on-off switch to the "on"
position and let the Li-ion battery charge for 8-10 hours the first time
being used. Once it is fully charged or after using it, please make sure
to push the switch to the "off " position in order to avoid any power
drain.
2) Please note the green LED light is the input power indicator which
informs you power from the charger is on, it does not connect to
battery “ In” and “Out”. Note that when the green light is on, this
doesn’t mean the battery is charging. You will still have to push
the switch "on" in order to charge or use.
Fig. 3 Energy Saving Li-ion Rechargeable Battery
Page 4 of 6

4
GENIE CCTV LTD.
CCTV HOUSE, City Park, Watchmead, Welwyn Grden City, Hertfordshire, AL7 1LT
Tel: [phone] Fax: [phone]
www.geniecctv.com
U SERS MAN UAL V3.3
4”Color Service Monitor
Model No.LSM-413
Ver sio n 3.3