Genie HDSD2PTZ20-IRDH User manual

HDSD2PTZ20-IRDH
Infrared Intelligent Vehicle PTZ Camera
User Manual

CONTENTS PAGE (IF IT IS A LARGE MANUAL)

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
3
1. Section 1 Header (Copy these for other sections)
2. Technical Specication
• Use this for Key features
Model Number HDSD2PTZ20-IRDH
*Design and Specications are subject to change without notice.

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
4
1. Precaution
Electrical safety
Conform to country and local electrical safety standard when using or installing the product.
Transportation
The PTZ’s should be protected against extremes of pressure, vibration and humidity during storage, installation and
transportation. The infrared PTZ camera is transported by integrated packing.
Installation of care
Please refer to the user installation manual when installing.
Please pick up the infrared parts gently and do not press it, or else it will damage the parts.
Please do not touch the infrared lens with your hands to avoid scratching it.
Requirements to service personnel
All the service work should be done by a qualied technician.
Do not disassemble the pan/tilt module
Do not disassemble screws, and don’ t maintain the parts in the Pan /Tilt by yourself. Only qualied and authorized
personnel can undertake repairs.
Environmental requirements
Requirements for PTZ:
Environmental temp -40 ~+60 OC
Humidity < 90%
Air pressure 86~106Kpa
AC Power supply 24V/25 00MA50/60HZ
Don’t place the camera near strong lighting devices
Don’t point the PTZ towards the sun or other bright objects when in use or not. It may aect image quality.
Function of waterproof
Our product has good waterproof, humidity proof and dust proof housing, which are IP66 rated.

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
5
2.1 Technology Parameter

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
6
2.3 PTZ Performance and Feature
The intelligent PTZ is complete new compact design camera using built-in temperature sensor and wiper func-
tion to allow full resolution picture in raining day. The camera uses a multi pin socket for convenient installation.
The Infrared LED range more than 60 meters and the camera can rotate exibly with low noise and allow wide
range capture. Certain auto-functions can provide perfect quality image for customer.
Built-in receiver
• All congurable options stored in main control board to protect against power cuts
• Integrate design and high durability
• 128 presets can be stored
• 01- 80 preset support auto-tour, and each tour can store up to 24 presets.
• 4 pattern tours
• Built-in direction indicator
• Built-in clock setting function
• 4 scan
• Built- in temperate re-indicator
• Rs4 85 Bus communication or American Dynamics Manchester code
• Support 24 masking zones at most (This function is decide by the parameter of built-in camera, if the camera
has not this function, this option is invalid.)
• 7 alarm input, 2 alarm output.
Pan Tilt Feature
• Aluminium alloy material and anti-violence design surface is well hidden
• Rapid heat removal; Level of protection IP 66 rated.
• Precise stepping motor drives the pan to run smoothly and react sensitivity.
• Integrated design, compact structure, easy to disassemble.
• Exquisite mechanical drive, support to rotate pan 360°continuously and tilt -9 0°~ + 90°, and may rotate
180°with auto ip.
• Pan 0.4°/s to rotate slowly, and the image doesn’t‘t vibrate.
Built-in digital camera
• High sensitivity, high resolution, and integrated digital processing
• Auto-focus
• Auto brightness control
• IR cut lter
• Auto slow shutter
• Auto-Iris
• Auto white balance
• Auto back light compensation
OSD menu
• All English menu can be selected.
• Visual OSD menu available. Revising the PTZ ‘s information and parameter by keyboard and OSD
• Set park action function and s et pre sets, or run scan, pattern , tour, etc during id le time.
• Auto-resume movement or carry outpointed movements after power up.

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
7
3 Performance
Internal temperature test
• Set time display
• When the temperature exceeds the limit, the screen will display an alarm
• When the temperature is under the limit, the PTZ will delay to start up, and when the camera temperature is
over the limit the PTZ will not start up.
• The fan measures the temperature and decides if it is to start or not, and prolong the life of the camera.
Time running
• User may set time running function everyday, and set dierent up to four actions in four dierent time of the
day, including preset, scan, pattern and tour.
Night View Function
• Infrared LED range more than 60 meters, user can manually control or auto-control infrared LED ON /OFF.
• Manual control can be done through keyboard and auto-control will automatically switch colour image to
black and white when low brightness is detected, black and white image will switch to colour.
Wiper function
• Wiper function can be set ON /OFF by using on of the 63 preset or OSD menu. On a raining day, the wiper do
more than providing high quality image , it can also clean-up the dirtiness on the surface of the lens.

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
8
3 Function Instruction
This passage mainly describes the main function and general principle of the PTZ camera. Dierent system
platforms have dierent operation methods, generally you should refer to the system manufacturer’s operation
manual. Please contact dealer to get necessary information, there are some particular requirements and opera-
tions under specic condition.
3.1
Camera ID
There are two 8-bit switches (SW 1 and SW2 ) on the board, SW2 is for setting communication baud
rate and controlling protocol. (For setting, please refer to 10.5 DIP switch setting besides the factory protocol
(FACTORY) , the PTZ is compatible with various popular protocol ls, such as PECLO-D , PECLO-P, ER NITEC, VCL, M
OLYNX, VICON, SANTACHI, PANASONIC, SAMSUNG, DIAMOND, KALATEL, LILIN, PHILIP S, VIDO B02，AD and so on.
Any controlling command must be based on the objective camera address, and the camera only answer to the
controlling command address which coincide with itsel f. There are three kinds of camera addess:
• Common address: Use camera’s switch number to set address 1- 8 bits, the address range is 1-2 54.
• Debug address: (Only factory protocol an d PELC O can be set) if camera ID is set 0, u ser may select any ad-
dress to control the PTZ.
3.2 Auto-run motion
Focus/speed proportion pan
When manually adjusting, for far focus situation, the PTZ responds at a high-speed so that touching rocker
slightly may make picture move rapidly, thus cause the picture to lose. To base on humanized d esign, the PTZ au
tomatically adjust pan and tilt rotation according to zoom ne ar and f ar, which make it is convenien t to operate
man ually to make tracking for the object. In the m enu, yo u may change system
parameter setting proport ion pan as ON t o run th is function.
Auto ip
If user holds the joystick in the down position, the camera rotates pan 180 degrees, then the camera
rotates tilts up to 180 degrees . In the menu, you may set the system parameter setting AUTO FLIP as ON
to run this function.
Park action
By the menu“ park time”and “park action”, use r may set auto-call preset or run tour, pattern, and
scan, etc after pointing a few minutes if t he PTZ doesn’t run any motions.
Power up action
By the menu“ power up action”, after the PTZ powers up or restarts, user may set auto- resume
mo vement s before power up and auto- call preset or run tour, pattern, and scan etc .

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
9
3. 3 Camera control
Magnication control
The user can control “Wide/Tele”to adjust zoom far and near of the image via the keyboard controller to obtain
panoramic image or close view that you need. The PTZ supports digital zoom and optical zoom.
Focus control
System defaults Auto focus. When the lens changes, the camera will auto-adjust focus according to the center of
the image to get legible image; users can also manually focus to get the desired image by operating the keyboard
“FAR/NEAR”. When operating the keyboard joystick, the camera resumes to auto focus.
The camera cannot auto focus in the following scenarios:
• Target is not the center of the image
• Observing the target closer and far at the same time, can not be clear at the same time.
• Target is a strong light object, such as neon light, spotlight , etc.
• Target moves too fast
• Target area such as wall
• Target is too dark or vague
• Target image is too small
Iris control
System defaults Auto Iris. Camera can rapidly adjust size of Iris, through the automatically induct the changing
of environment ray, and thus make the brightness of deferent image stable.
User may adjust Iris by controller keyboard “open/close”to get required brightness that you need. User also can
resume auto Iris by joystick operation. When controlling the Iris manually, the PTZ locks current position you
manually controlled; when operating joystick, the PTZ resume auto Iris.
Auto back light compensation
Camera sub-area can carry out auto back light compensation. Under a strong light background, camera will auto
compensate light for the darker object and adjust daylight to the bright background. In order to avoid making
the image lack delity by the back line is too bright, and the object is unable to recognize because of darkness,
thus gain legible image.
Auto white balance
Camera can automatically adjust white balance in accordance with the alteration of background lightness
to reach a true colour.
3. 4 Monitor function
Set and call preset
Preset function allows the PTZ to store current pan/tilt angle, zoom and other position parameters into the inter-
nal memory. When necessary the PTZ recalls these parameters and adjusts the camera to that position. Users can
store and recall presets easily and promptly by using keyboard controlling. The PTZ can store up to 128 presets.
Tour
Auto tour is a built-in function in the PTZ, to make arranged preset in needful order in tour queue by program-
ming it in advance. To make the camera tour between presets by inserting presets in cruise tour. It is feasible to
program tour order, each time as you run a tour, you can set the park time of preset. A tour can store 24 presets.

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
10
4. System setting
4. 1 Basic operation
4.1.1 Current-carrying to PTZ and Self-testing
The PTZ conducts self-testing after current-carrying , and it rotates slowly until displaying pan origin that is de-
fault setting, then moving to tilt origin, the lens is adjusted from far zoom to near zoom, then from near zoom to
far zoom, when the self-testing is nished, the relevant system information displaying on the screen, as follow:
The information will not disappear until you stop to operate the system. If you set“power up action”, the PTZ will
automatically activate motions after self-testing. How to operate the function? We will explain detail introduction
in following passages.
4. 1. 2 Call the main menu
The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds. All the
menu setting must be entered into the main menu at rst.
4. 1.3 Menu and keyboard operation
Keyboard operation:
[OPEN] when choosing pictures, it means to increase Iris; when setting menu, it means to enter into the
next menu or setting, or means to save after setting.
[CLOSE]when choosing pictures, it means to reduce Iris; when setting menu, it means to exit without saving
setting.
[NEAR] Focus to near
[TELE] Increase magnication
[WIDE] Reduce magnication
Joystick to up: When choosing menu, it means to choose the former one; when choosing picture, it means cam-
era tilt up.
Joystick to down: when choosing menu, it means to choose the next one; when choosing picture, it
means camera tilt down.
Joystick to left: when choosing menu, it is equal with [CLOSE], when choosing picture, it means
camera tilt left .
Joystick to right: when choosing menu, it is equal with [OPEN], when choosing picture, it means
camera tilt right.
Press [TELE] and [WIDE] at the same time, it means 3D joystick rotates joystick cap.
Menu operation
“BACK” : Back to the former menu
“EXIT” : Exit to menu
“ ON” : Open some setting
“OFF ”: Close some setting
“ON”: Open some setting
“OFF ”: Close some setting

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
11
4. 2 Edit dome label
When using a lot of the PTZ systems, in order to identify each PTZ, the
systems supports title settings. The settings are as follow
1) The system enters into the main menu by calling 95 preset or by calling 9
preset twice within 3 seconds.
2) Moving the joy stick up and down to move the cursor to [ SYSTEM SET-
TING], and pressing [OPEN] to enter into the next menu.
3) Moving the joystick up and down to move the cursor to [EDIT PTZ LA-
BEL], and pressing [OPEN] to enter into the label setting menu.
4) Moving the joystick up/down to move the cursor to [LABEL], and press-
ing [OPEN] to edit current label
5) When the cursor is twinkling on the rst character of the label, move the
joystick to choose another character, after editing, press [OPEN] to save.
6) Move the joystick to [BACK] and pressing [OPEN] will let you go to the
previous menu
The label may be set to16 characters, and doesn’t need editing characters.
Pressing [OPEN] continuously to jump over and using spacebar to replace
the deleted characters. When you nish
to edit a character, press [OPEN] to enter into the next editing
character; when you editing the last character, pressing [OPEN]
to save. Press [Close] to exit.
Characters of label available for choosing are as follow: 0- 9, A-Z,:<>-.,
Space.
Other label input ways are the same as above

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
12
4. 4 Display setup
1) The system enters into the main menu by calling 95 preset or by call-
ing 9 preset twice within 3 seconds.
2) Tilt up/down joy stick to SYSTEM SETTING, press OPEN to enter sub-
menu.
3) Tilt up/down joy stick to [DISPLAY SETUP], press [OPEN] to enter
“display setup” menu, May setting the content of the display set up as
follow:
• [DOME LABEL]
• [PRESET LABEL]
• [ZOOM LABEL]
• [ZONE LABEL]
• [DIRECTION LABEL]
• [TEMPERATURE LABEL]
• [TIME LABEL]
• [DATE LABEL]
4) Taking display PTZ label as an example to explain the operation
process. Tilt up/down the joystick to move the cursor to Dome LABEL
OFFER, press[OPEN], there is a sign “ ” besides Dome [LABEL], the cursor
is twinkling besides [OFF], as left picture shows;
5) Joystick tilt up/down, setting number changes between ON/OFF,
when setting [ON], it means to display“PTZ label”; when setting [OFF],
it means not to display“PTZ label”. When pressing [OPEN], the cursor
jump back in front of DOME LABEL, this means label setting is nished,
when moving the cursor to EXIT, it means exiting the menu setting.
The displaying information on the screen will change with the PTZ
rotation ; Through the information on the screen, user can see current
PTZ in side temperature, magnication, display zone etc. When all the
label are displayed, the PTZ works as the following picture shows,:
(In the picture “305” means pan angle,“45” mean s tilt angle. )

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
13
4. 5 Systematic motion control
Systematic motion controlling may control a series o f canonical move-
ment of the PTZ, and play an important role in controlling the PTZ.
1) The system enters into the main menu by calling 95 preset or by call-
ing 9 preset twice within 3 seconds.
2) Tilt up/d own joystick to SYSTEM SE TTING, press [OPEN] to enter sub-
menu
3) Tilt up/down joystick for MOTION , press [OPEN] to enter systematic
motion controlling menu, as left picture shows.
4. 5. 1
Auto ip
1) Operate joystick , move the cursor to [AUTO FLIP] : press [OPEN] to
enter “auto ip ”setting, tilt up /down joystick , for example: choosing
“ON”to open“ aut o ip”; choosing “OFF” to close“ auto ip”.
Press [OPE N] to save.
R EMAR K: When opening the auto ip function, user holds the joystick
in the down position, the c amera rotates pan 180 degrees, after the
camera rotates tilt up to 180 degrees.
4. 5. 2 Speed proportion pan
.Operate jo ystick, move th e curso r to，PR OPORTIONAL PAN，; press
，OPEN， to enter“ propo rtion pan”setting, til t up/down joystick to ch-
oose, if choo sing ，ON，, it means to open proportion pan ; if cho osing
，OFF，, it means t o close proportion pan , press ，OPEN，to save.
OPERATION KNACKS
When manually adjusting, for far focus situation, the PTZ responds at
a high-speed so that touching joystick slightly may make picture move
rapidly, thus cause the picture to lose. To base on humanized design, the
PTZ automatically adjust pan and tilt rotation according to zoom near
and far, which make it
is convenient to operate manua lly run after object.

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
14
4. 5. 3 Park action
This setting allows the PTZ to run an appointed action after it enters
stand by mode (1-240 minutes). If default sets as 0 , it means not to run
this action automatically.
1) Operate joystick, move the cursor to [PARK T IME], press [OPEN]
to set park time, the range is 0-240 (minutes), press [OPEN] to save.[PARK
ACTON] is running action at park time, when [PARK TIME] sets as 0, this
item can’t be set
2) Operate joystick, move the cursor to [PARK ACTON], press [OPEN]
there will be a sign in the front of [PARK ACTON] , the cursor will jump
to the right, after tilt up/down use joystick to choose“ park action”the
options for choosing are as follow, press [OPEN] to save.
• NONE- (default) none action
• PRESET - Use preset 1-80
• SCAN -Run scan
• PAT1- Run pattern X
• TOUR- Run tour
4.5.4 Power up action
The PTZ starts to run actions after self-testing, if nobody intervenes , it
will repeatedly run this action continuously , if default sets as [NONE].
1. Operate joystick, move the cursor to [POWER UP ACTION] : press
4.5.5 Fan startup by temperature
The temperature of the PTZ will rise, when it is in high temperature the
fan will open automatically, when the temperature reaches to a very
high degree the system will shutdown to protect electronics.
Operate joystick, move the cursor to [FAN ENABLED] : press [OPEN] , the
cursor will skip to the back option. The user can choose the fan to start
up temperature, and press [OPEN] to save it in actual condition.
The default setting temperature of the fan startup is 40 OC. The user can
also enter the fan startup setting to adjust the temperature of fan start-
up. As picture shows: the temperature range is 0-60 OC. [TEMP] can
switch the temperature between fahrenheit and centigrade.

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
15
4.5.6 Advance setting
1. Operate joystick and move to [ADVANCE SETTING] , press [OPEN]
to enter into“advance setting”;
[EIS ENABLED]: Electronic Image Stabilizer function;
[PRESET FREEZE]: Function of Preset Freeze means during calling pre-
sets, the monitor displays the image before call presets, and releases the
freeze image when the camera arrives the appointed presets.
[HE AD-DO WN]: Settings of Top/Down. “ON” means DOWN,
“OFF”means TOP.
[DE FOGGER] : Lens of PTZ will be fogged when PTZ works in quite cold
temperature . In order to get clear image , defogger wil l open automati-
cally at the appointed temperature. Choosing [DEFOGGED] by
operating the joystick, and pressing [OPEN], then cursor leap to the
optional. Choose the temperature to run the defogger, and press [OPEN]
to save.
Range of Temper ature: 0~30.
[ADJSPEED] The rotation percent age of P/T, 100 means factory speed,
80 means 80% of factory speed.
[WIPER]: Wiper runs by calling 63 Preset.
[MODE]: Setting of Infrared light. Call 62 preset to run Infrared light un-
der the setting of MANUAL. Save 62 preset to close the infrared.
[DELAY TIME]: Setting the auto close time of IR light, ranging from
1-240 Minutes.
[IR Cut Filter0: Setting the imaging model after the IR light as ON, three
modes for choice : Auto, Color, Black.
[ACTIVATE AUX 1] Whether to link AUX 1 when open the IR light,
“ON”means Link. “OFF”means not to link.
[Auto] is invalid as it’s searchlight, it must be
controlled under [Manual]status.
[LED1] For LED brightness adjustment, range: 50- 200, Brightness
Increase in proportion as bigger digits is chosen.
[LED 2] S ame as the above
[LE D 3] Temporarily unavailable
[LIGHT] Options of light sources
(Temporarily unavailable)
1.After the PTZ set the EIS function, if the PTZ wobble slight when run-
ning, the camera will shield the wobble picture and ma ke the picture
calm and smooth.
2.When start-up preset freeze, it can eliminate the sense of ash caused
by calling presets when open function of Preset Freeze, which can re-
duce the storage space of DVR if image is stored by DVR.
These function in the a dvance setting menu depends on the
models and parameters of built-in camera in PTZ, if the camera
haven’t this funtion, then this function is invalid.
The option is useless (N/A) when the camera module has no
such funtion

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
16
4. 6 Clear and restart
1) The system enters into the main menu by calling 95 preset or by call-
ing 9 preset twice within 3 seconds.
2) Tilt up/down joystick to [SYSTEM SETTING], press [OPEN] to enter
submenu.
3) Tilt up/down joy stick to [CLEAR] , press [OPEN] to enter submenu, as
left picture shows.
• [CLEAR ALL ZONES]
• [CLEAR ALL PRESETS]
• [CLEAR ALL PATTERNS]
• [CL EAR ALL TOURS]
• [CLEAR ALL WINDOWS]
• [FACTORY DE FAULTS] : resume the factory default. Run this func-
tion, the camera parameter and system parameter will resume
to factory default, clear all windows and alarm setting. Please be
cautious to use this function.
• [RESTART]
4) Set clear zone as an example to explain the process. Tilt up/down
joystick to [CLEAR ALL ZONES], press [OPEN] to clear all zones.
Once clear all commands in the controlling menu, it cann’t
resume, so please be careful of using it.

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
17
4.7 Password set
1. The system enter s into th e main menu by call ing 95 preset o r by
calling 9 preset twice within 3 seconds.
2. Operate the joystick up and down, move the cursor to [SY STEM
SETTI NG] , press [OPEN] to call the submenu.
3. Operate the joystick up and down , move the cursor to PA SSWO RD
[SETUP], press [OPEN] to cal l the su bmenu . Please refer t o the le ft
SYSTEM SETTING
EDI T PTZ LABEL INITIAL INFO DISPLAY SETUP MOTION CLEAR PASS-
WORD SETUP
4. Operate the joystick up and down , move the cursor t o [OLD]
PASSWORD, press [OPEN ] to choose it, operate the joystick right and
left to input the password, Tilt up and down to choose the number
which you need.
• [NE W PASSWORD] Enter the new password
• [CONFIRM PASSWORD] Conrm the new password
• CLOCK SETTING DOME ADDRESS BACK
• ENABLE PASSWORD
• Set PASSWORD o / on
• EXIT
The password function is noneective under the PASSWOR D OFF.) It
means that users can enter into the main menu without a password.
The password function is eective under the password ON. It means
that user can only enter into the mian menu with a password

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
18
4.8 Time set
1. The system enters into the main menu by calling 95 preset or by call-
ing 9 preset twice within 3 seconds.
2. Operate the joystick up and down, move the cursor to [SYSTEM SETT
ING] , press [OPEN] to call the sub menu.
3. Operate the joystick up and down, move the cursor to [CLOCK
SET TING] , press [OPEN] to call the submenu. Please refer to the left
picture.
Operate the joystick up and down, move the cursor to [TIME], press [OP
EN] to choose it, move the joystick up and down to choose the number
you need, move the joystick right and left to set hour, minute, second.
• [DATE] set year, month, date
• [DAY] set week
• [BACK] return to the former menu
• [EXIT] exit the main menu.

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
19
4.9 DOME Address Setting
1. The system enters into the main menu by calling 95 preset or by call-
ing 9 preset twice within 3 seconds.
2.Tilt up/down the joystick and move the cursor to [SYSTEM SET TING],
press [OPEN] to enter submenu.
3. Tilt up/down the joystick and move the cursor to [DOME ADDRESS],
press [OPEN] to call dome parameter setting menu
S/N : Serie s No. of the dome
CONF: Conrm S /N and input the same NO. with S/N
DOME ADDRESS: Set dome address (ID ran ge: 001-255)
1. If [S/N] and [CONF] are dierent, the above operation can’t
be implemented
2. The PTZ address should be set as 255 (mean set Switch 1 as
ON), there will be display this item [PTZ ADDRESS]
3. After setting PTZ address, the PTZ need to restart, then the
PTZ address will be eective

CHANGE THIS TO WHAT THE PRODUCT IS AND COPY INTO THE MASTER PAGE A
20
5. Camera setting
5. 1 Zoom speed
1. The system enters into the main menu by calling 95 preset or by call-
ing 9 preset twice within 3 seconds.
2. Tilt up/d own joystick to [CAMERA SETTING] , press [OPEN] to enter
submenu
3. Operate joystick, move the cursor to [ZOOM SPEED]; press [OPEN]
will appear a sign “ “ in the front of [ZOOM SPEED], the cursor moves
to right , tilt up /down joystick to choose [HIGH] or [LOW]
4. Press [OPEN] to save, press [CLOSE] to cancel