Gentec TFT8000 User manual
90˚ Bubbler
TFT8000, TFT8000L
45˚ Bubbler
TFT8050
Bubbler with separate buon
TFT8020
Up Right Bubbler
TFT8050UR, TFT8050URL
INSTALLATION
MANUAL
FLOSTOP BUBBLERS
2
Contents
Product Features 3
Product Range 4
Technical Drawings 5
Unit Components 7
Installation Instructions 8
Maintenance 10
Time Adjustment Instructions 12
Water Flow Adjustment 13
Product Warranty 14
3
www.gentecaustralia.com.au
The hydraulically operated time flow tapware will enhance your facility by
providing high-level hygiene and extensive energy and water savings. Varied
standard time delays are available. Adjustable time delay of 1 - 40 seconds is
supplied with some products.
Timed control features Adjustable timing from 1 - 40
Seconds
Installation and servicing
For durability please ensure to install
all parts including strainers and flow
regulators.
Usage features Adjustable timing via adjustment
screw for 1 - 40 seconds
Application
Commercial premises, Healthcare
accessible areas, child care facilities,
Sports facilities.
The FLOSTOP Soft close, timed flow product range is anti-vandal and has
been designed to withstand heavy use in any commercial application for over
1.000.000 cycles of operation.
Flostop Bubblers by Gentec
The more
stars the more
water efficient
WATER R ATI NG
www.waterrating.gov.au
Licence No. 1334
GENTEC AUSTRALIA
In accordance with AS/NZS 6400
3.5
litres per
minute
WM 74513
AS/NZS 3718
ApprovalMark
4
TFT8000 / TFT8000L TFT8020
90°BUBBLER WITH PROTECTIVE GUARD BUBBLER WITH SEPARATE PUSH BUTTON
TFT8050 TFT8050UR / TFT8050URL
45° BUBBLER WITH PROTECTIVE GUARD UP RIGHT BUBBLER WITH PROTECTIVE
GUARD
Product Range
*Use 350Kpa pressure reducing valve for extended life and beer operation
5
www.gentecaustralia.com.au
TFT8000
90°BUBBLER WITH PROTECTIVE GUARD
TFT8020
BUBBLER WITH SEPARATE PUSH BUTTON
Technical Drawings
*Regular service must be carried out on the product to avoid product failure.
97
34
34
92
56.5
G1/2
G1/2
G1/2
G1/2
5.7
W26X19
Ø44.5
Ø49.8
Ø33
59.5
81º
29
2
17.90
20
117.60
4035
32
W26x19
16
50
GENTECH AUSTRALIA PTY. LTD.
59.5
49.5
32.5
31 55.8
G1/2
79.7
60
27
135
G1/2
82
Ø26
Ø25
Ø30
90º
GENTECH AUSTRALIA PTY. LTD.
59.5
49.5
32.5
31 55.8
G1/2
79.7
60
27
135
G1/2
82
Ø26
Ø25
Ø30
90º
97
34
34
92
56.5
G1/2
G1/2
G1/2
G1/2
5.7
W26X19
Ø44.5
Ø49.8
Ø33
59.5
81º
29
2
17.90
20
117.60
4035
32
W26x19
16
50
6
TFT8050
45˚BUBBLER WITH PROTECTIVE GUARD
TFT8050UR
UP RIGHT BUBBLER WITH PROTECTIVE GUARD
Technical Drawings
GENTECH AUSTRALIA PTY. LTD.
G1/2
55.8
Ø26
Ø25
G1/2
Ø32.5
Ø30
49.5
185 60
27
82
59.5
31
122º
GENTECH AUSTRALIA PTY. LTD.
G1/2
Ø32.5
Ø30
60
27
Ø25
49.5
59.5
162.7
82
55.8 31
*Use 350Kpa pressure reducing valve for extended life and beer operation
7
www.gentecaustralia.com.au
No. Description Qty
01 Bubbbler Guard 1
02 Body 1
03 Flow Cup 1
04 Cartridge 1
05 Handle 1
06 Cover Screw 1
No. Description Qty
07 O Ring 1
8A Locking Screw 1
8B Screw for water control
adjustment 1
09 Flow Regulator 1
10 Strainer 1
*Regular service must be carried out on the product to avoid product failure.
Unit Components
8
Installation Instructions
BUBBLERS
TFT8000, TFT8050, TFT8050UR, TFT8050URL
For all Units:
1. Flush the new pipe prior to installation.
2. Bubblers should be installed with isolating stop tap valve.
3. Install the Flow regulator and place the strainer in the inlet connection before screwing the
valve to the water inlet.
4. Screw the bubbler to the water inlet.
5. The drinking taps are fitted with a flow
regulator. When applying thread tape or
sealant to the inlet, ensure the opening is
not obscured.
* Failure to do so may restrict or block the
flow regulator affecting the flow of water.
Important Information
We do not recommend dismantling
the internal parts of the tapware set.
The tapware are individually factory
assembled and tested to give the
best performance.
*Use 350Kpa pressure reducing valve for extended life and beer operation
Thread
Thread
9
www.gentecaustralia.com.au
BUBBLER WITH SEPARATE PUSH BUTTON
TFT8020
1. Allow a 32mm cut-out hole to fit the
push activated button mechanism. Drill a
3mm hole to fit the Anti-vandal pin. This
should be fixed to prevent movement of
the button.
2. The timed flow valve should be fitted to
the push button assembly to install the
bubbler outlet.
3. Adjust in the cartridge length to
suit the basin surface thickness.
(See Figure 3)
4. Fit the flexi hoses (not provided) to the
water inlet and outlet. Ensure the arrow
on the button body is aligned with the
water flow direction. (Pointing to the
water outlet).
5. To install the bubbler outlet allow a cut
out no greater than 38mm and connect
the flex hose from the valve.
• Note: Ensure the arrow in the valve
body is facing the connection to the
water Outlet.
*Regular service must be carried out on the product to avoid product failure.
Figure3
Figure1
Figure2
10
Maintenance
Important Note
For adequate maintenance, please unscrew and clean the strainer, then proceed to flush the
line before putting back the strainer.
O Ring Kit service
For the following steps, a qualified plumber must be in charge of the maintenance and handling of
the tapware in order to keep product Warranty. The damage on parts after dismantling a product
would not be covered by the warranty.
First start by shuing off the main water supply.
No. Description Qty
01 Handle 1
02 Cartridge 1
03 Bubbler Body 1
04 Stem 1
05 Head Valve 1
06 Washer Gaco 1
07 O-Ring 1
08 Crown Ring 1
09 O-Ring 1
10 Stopper 1
11 Washer Gaco 1
Note
•The “O” Ring Kit consists
of #6, #7, #9, #11
*Use 350Kpa pressure reducing valve for extended life and beer operation
11
www.gentecaustralia.com.au
1. Remove the head valve using a shifter
on the flats and remove the cartridge.
(Figure 1)
2. Undo the stopper (10)
3. Set aside the crown ring (8)
4. Set aside the head valve (5) from the
stem
5. Remove the washer Gaco (6) from the
head valve (5) and replace with the new
washer gaco (6)
6. Remove the Gaco (11) from the stopper
(10) and replace it with the new washer
gaco (11)
7. Remove the “O” Ring (9) and replace it
with the new “0” Ring (9)
8. Remove the “o” Ring (7) and replace it with
the new “o” Ring (7)
9. Using the existing crown ring (8) place it
back into the head valve (5)
10. Place the stem (4) through the head valve
(5)
11. Apply a drop of Loxeal to the thread of the
stem (4)
12. Replace the stopper (10), ensure the “o”
Ring (9) is in place, then tighten the stop-
per (10). Do not overtighten.
13. Fit the cartridge and handle back into the
body, and tighten. Do not overtighten.
Important Information
The damage on parts after
dismantling a product would not be
covered by the warranty.
*Regular service must be carried out on the product to avoid product failure.
Figure1
12
The adjustable cartridge used is a 30mm
diameter handle with a small 3mm hole
in the front of the handle. The hole in the
handle has a grub screw for adjusting the
run time.
• To adjust the timing, you will need to
use the allen key provided or you need
a 1.2mm allen key to adjust the timing.
• Turning the screw in clockwise will
reduce the run time.
• Turning the screw anti clockwise will
increase the run time
Fixed Timing Adjustment
Please contact GENTEC before changing flow
cups
Our Flostop range is available in the following
fixed timing options
These options are available upon request
and are factory installed. *Refer to the chart
below
Changing the flow cup yourself may void the
product warranty.
ADJUSTABLE CARTRIDGE (0 TO 40 SECONDS)
FCC. Description
TFT9050 Flow cup 4 - 6 Sec
TFT9052 Flow cup 8 - 12 Sec
TFT9053 Flow cup 12 - 16 Sec
TFT9054 Flow cup 40 Sec
This option is suitable for the following references: TFT8000, TFT8050,
TFT8050UR, TFT8050URL
Time Adjustment
*Use 350Kpa pressure reducing valve for extended life and beer operation
13
www.gentecaustralia.com.au
WATER FLOW ADJUSTMENT
This option is suitable for the following references: TFT8000, TFT8050,
TFT8050UR
1. Unscrew the top cap (6) (7)
2. Remove the locking screw (8A) and adjust the flow with adjustable screw (8B) using a
3mm Allen key.
3. Screw the top cap (6) (7) back.
To adjust the water flow:
• Turning the screw clockwise will reduce
the water flow.
• Turning the screw anti clockwise will
increase the water flow.
*Regular service must be carried out on the product to avoid product failure.
Do not remove the
water control screw
(8B) from the body
14
Warranty
GENTEC PRODUCT QUALITY WARRANTY
*Use 350Kpa pressure reducing valve for extended life and beer operation
You have purchased a quality product from GENTEC
Australia Pty Ltd ABN 581 552 50285 ). This product is
covered by a 10 year replacement product warranty
and a 24 month warranty on spare parts and labour.
1. Warranty
1.1 This warranty is given by the Principal subject to
the terms and conditions set out in this document.
1.2 The Principal warrants that the Goods are
free from defects in materials and workmanship
for the time period specified for the Goods in
the Product Index. If Your Goods are found to be
defective within that time, we will repair or replace
the Goods.
1.3 This warranty does not cover accidental
damage, wear and tear, consequential or incidental
loss, or any damage caused by You, including if
the Goods were not installed in accordance with
the manufacturer’s instructions, the PCA and AS/
NZS3500.
1.4 You are required to service the Goods regularly.
Failure to do so may cause this warranty to be
voided.
2. Procedure
2.1. If you consider that the Goods are defective,
you must cease use of the Goods immediately
and provide notice to the Principal in writing as
soon as is reasonably practicable after discovering
the alleged defect.
2.2. The notice referred to in clause 2.1 must state
the following:
2.2.1 the alleged defective Goods;
2.2.2 what the alleged defects are;
2.2.3 where the Goods are located;
2.2.4 when the Goods were purchased
2.2.5 the invoice number relating to the
purchase of the Goods;
2.2.6 whether the main water to the unit is able
to be turned off;
2.2.7 include pictures of the alleged defect; in a
reasonable time.
2.2.8 completed credit card authorisation in the
form set out in Schedule 2 to these conditions
accepting liability in accordance with clause 2.6
if the product is not faulty.
2.3 The Principal will, on receipt of a notice in
accordance with clause 2.2, issue a case number
for the investigation of the alleged defective
Goods.
2.4 In the event that the Goods are to be returned
to the Principal You may bring or send them to
one of our service locations or sites. If the cost of
returning the goods to us is significant because of
the nature of the failure or because of the size or
height of the goods, the Principal will collect the
goods from you within a reasonable time of You
providing notice in accordance with clause
2.2. If the cost of returning the Goods to us is
not significant, you are responsible for this cost
(although, you are entitled to compensation for
reasonably foreseeable costs incurred because
of the defect, including the cost of returning the
goods to us for repair, replacement or return).
2.5 In the event that the Principal or its agent are
required to inspect the Goods at the location
of their use or storage, You will, on reasonable
notice, allow the Principal to inspect the allegedly
defective Goods at the location of their use or
storage.
2.6 You are responsible for Your expenses relating
to a warranty claim, except as otherwise provided
for in this document. If the Principal is required
to attend Your site to inspect the Goods, and
it is found that there is no defect or the defect
has been caused by the circumstances listed in
clause 1.3, You will be responsible for the Principal’s
reasonable costs of attending Your site. Where
reasonably possible, we will notify you to give you
the option of paying for a repair or replacement
15
www.gentecaustralia.com.au
*Regular service must be carried out on the product to avoid product failure.
(however, we have no obligation to do so). We
will also provide you with all relevant information
associated with obtaining a repair or replacement
of the good (including the costs involved and how
the repair or replacement will be performed).
2.7 If the Principal agrees that the Goods are
defective, they will be replaced or repaired within
a reasonable time.
2.8 You have a duty to mitigate your loss in relation
to a warranty claim. You must notify the Principal
of major failures of the Goods within 3 business
days of you becoming aware of such major failure.
If you fail to notify us within this timeframe,
then we disclaim all liability for consequential or
indirect loss as well as losses of revenue or profits.
2.9 For the avoidance of doubt, it is in the
Principal’s sole discretion as to whether or not the
Goods are defective and therefore covered by the
warranty provided in this document. Any invoices
for services or replacement products will not
be paid for by the Principal without prior written
authorisation.
3. Mandatory Warranties
3.1 The Goods come with guarantees that cannot
be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund
for a major failure and compensation for any
other reasonably foreseeable loss or damage.
You are also entitled to have the Goods repaired
or replaced if the Goods fail to be of acceptable
quality and the failure does not amount to a
major failure.
4. Exclusion of Warranties and Limitation of Liability
4.1. Except as may be set out in this document
and the Quote, the Principal make no express
warranties or representations in relation to the
Goods or their delivery.
4.2. To the full extent permitted by law, the
Principal:
4.2.1 excludes all implied warranties and
conditions under statute or general law as to
merchantability, description, quality, suitability,
fitness for purpose or otherwise;
4.2.2 is not liable for loss of profit, indirect,
consequential or incidental loss, damage or
injury in connection with the Goods;
4.2.3 is not liable for the labour costs
associated with replacing the Goods;
4.2.4 is not be liable for any transport or
freight costs in relation to any warranty claim
and the repair or replacement of the Goods;
4.2.5 limits its liability in connection with
the Goods (however arising, whether in tort,
contract or otherwise) at its option and sole
discretion to:
4.2.5.1 replace the Goods or the supply of its
equivalent;
4.2.5.2 repair the Goods;
4.2.5.3 pay for the cost of replacing the Goods
or acquiring their equivalent; or
4.2.5.4 pay for the cost of having the Goods
repaired.
4.3 The warranties given by the Principal will not
apply in the event of defects, failures or other
matters regarding the goods where due to:
4.3.1 an act, default, omission or representation
made by some other person, excluding Gentec
or its manufacturer (for example, damage
caused by the misuse or mistreatment of the
good by the customer or someone else);
4.3.2 without limitation to (4.3.1) above, a failure
to install the goods in accordance with any
plumbing codes of practice prescribed by
an Australian Federal or State Government
body or organisation (including regulators),
any plumbing codes of practice generally or
any guidelines or instructions issued by the
Principal in relation to the Goods; or
4.3.3 a cause independent of human control
that occurs after the goods left our control.
4.4 Any of the warranties given by the Principal
may be voided by failing to comply with the
directions set out in the various user manuals
or other instructional material provided to You by
16
MAR-IM-FLOT01-MB-041219
www.gentecaustralia.com.au
P: +612 9319 4422
F: +612 8088 7635
Unit 6 20-28 Rickey St,
Mascot, Sydney, NSW 2020
the Principal in relation to specific Goods.
4.5 However, nothing in this clause will prevent
You from exercising any rights which You may
have under the Competition and Consumer Act
2010 or any other law which cannot by law be
excluded or modified by agreement.
5. Notices
5.1 Any notice in connection with this
document must be given in writing.
5.2 Any notice in connection with this
document is taken to be received:
5.2.1 if hand-delivered, on delivery;
5.2.2 if faxed, at the local time (in a place
of receipt of that fax) which then equates
to the then time at which the fax is sent as
shown on the transmission report which is
produced by the machine from which that
fax is sent and which confirms transmission
of that fax in its entirety unless that local
time is not a Business Day, or is after 5pm
on a Business Day, in which case that
communication will be deemed to have
been received at 9am on the next Business
Day;
5.2.3 if emailed, at the local time (in a place
of receipt of that email) which then equates
to the then time at which the email is sent
as shown on the transmission report which
is produced by the computer from which
that email is sent and which confirms
transmission of that email in its entirety
unless that local time is not a Business Day,
or is after 5 pm on a Business Day, in which
case that communication will be deemed
to have been received at 9 am on the next
Business Day; and
5.2.4 if posted, seven (7) days after being
placed in the post; unless a later date is
specified in it, and takes effect on the date
it is taken to be received.
5.3 The address for any notice to be
delivered to the Principal is as follows:
This manual suits for next models
5
Table of contents
Other Gentec Plumbing Product manuals
Gentec
Gentec Single Lever Basin Mixer GPN1000 User manual
Gentec
Gentec JETF1200 User manual
Gentec
Gentec SMARTEC PLUS User manual
Gentec
Gentec SMARTEC STS1000 User manual
Gentec
Gentec NGM1000 User manual
Gentec
Gentec GPure Bubblers GPT8000 User manual
Gentec
Gentec GPT7000 User manual
Gentec
Gentec GPR1000 User manual
Popular Plumbing Product manuals by other brands
Marco Mammoliti
Marco Mammoliti BOX DOCCIA Installation, use and maintenance manual
Delta
Delta TALBOTT 35960LF quick start guide
Delta
Delta T1817 Series parts list
resideo
resideo Braukmann BA300 installation instructions
American Standard
American Standard One 2064.461 installation instructions
Sanela
Sanela SLU 16 Instructions for use
