Getinge Meditrax User manual

Getinge Australia Pty Ltd
PO Box 50, Bulimba QLD 4171, Australia
Phone: 1800 GETINGE
[e-mail]
www.getinge.com/au
MLAI081015.V1
Meditrax
Label Applicator
Easy label reloading
Quick and simple
number changing
Laser cut print bands
for clarity of print
Ink cartridge
change
Universal pressure device for
consistent print quality and
reduced risk of RSI
Constructed for impact
resistance
 Durability
 Ease of Use
 Fit for the purpose
Professional Labelling For Health Care Professionals

Getinge Australia Pty Ltd
PO Box 50, Bulimba QLD 4171, Australia
Phone: 1800 GETINGE
[e-mail]
www.getinge.com/au
MLAI081015.V1
Knowing your Label Applicator
J
IK HM
L
ABCDEGF
AHandle lever
BHandle
CLabel roll holder
DDialing/Viewing area of printhead
EDialing knob printhead
FFront cover
GBase plate retaining latches (on both sides)
HLabel applicator roller
ILabel guide
JBase plate
K Label backing paper
LTransport unit
MTear-off edge for backing paper
Meditrax
Label Applicator

Getinge Australia Pty Ltd
PO Box 50, Bulimba QLD 4171, Australia
Phone: 1800 GETINGE
[e-mail]
www.getinge.com/au
MLAI081015.V1
Base plate
retaining latches
Base plate
Feed through here
2. Pull out approximately 15cm of labels and feed the labels down through the label applicator.
Feed label down
Front of label
applicator
Base plate
3. Slide the new label roll into the label roll holder (C) until the label core snaps into place. The labels
should be placed in the holder with the label side facing up.
Labels sit in label roll
holder here
4. Turn the label applicator over and pull the
labels through so they hang over the front
of the applicator. Click the base plate (J)
closed.
5. Feed the labels through and out the back of the
transport unit (L) until the labels emerge
between the tear-off edge (M) and the handle
lever (A).
Transport unit Tear-off edge
Handle lever
6. Turn the label applicator over and squeeze the handles (A+B) repeatedly to tighten, self align and
cause a printed label to be dispensed.
1. Open the base plate (J) using the base plate retaining latches (G). Slide the latches on both sides of
the label applicator to open the base plate.
To Load the Label Applicator
Meditrax
Label Applicator

Getinge Australia Pty Ltd
PO Box 50, Bulimba QLD 4171, Australia
Phone: 1800 GETINGE
[e-mail]
www.getinge.com/au
MLAI081015.V1
Important: Please note the ink pad cannot be re-inked.
External surfaces of the label applicator can be decontaminated with an alcohol wipe.
It is suggested that this is completed on a routine basis.
Push ink
roller up into
applicator
5. Close the front cover (F), by clicking it shut. The label applicator is now ready for operating.
Ink roller
sitting in
guide
channels
4. While keeping your thumb on the word “TOP” insert the new ink roller into the guide channels and
push up into label applicator and release handles. Always check that the studs of the ink roller move
within the guide channels.
Keep your thumb
on the word “TOP”
3. To insert the new ink roller, squeeze the handles (A+B) together, and hold.
Remove and
discard used
ink roller
Ink roller
2. Squeeze the handles (A+B) together, and hold. The yellow ink roller will appear in the front opening
and can be easily removed.
Front cover
1. Hold the label applicator horizontally and pull open the front cover (F) and leave open.
Guide
channels
Changing the Ink Roller
Meditrax
Label Applicator