Gigabyte GA-6VA7+ User manual

R-20-01-000107
6VA7+
USER'S MANUAL
1. System power on by PS/2 Mouse: First, enable this function in
CMOS Setup, then you can power on the system by double
clicking the right or left button of your PS/2 Mouse.
2. System power on by Keyboard: If your ATX power supply
supports larger than 300 mA 5V Stand-By current, you can
power on your system by entering password from the
Keyboard after setting the “Keyboard power on” jumper (JP1)
and password in CMOS Setup.
3. Support Modem Ring-On. (Include internal Modem and
external modem on COM A and COM B)
4. Wake-up on LAN supports(on J7): Your ATX power supply
must support larger than 720 mA 5V Stand-By current.
5. Support 3 steps ACPI LED.
CeleronTM Socket 370 Processor MAINBOARD

Quick Installation Guide
REV. 2.0 First Edition

6VA7+
1
Theauthorassumesnoresponsibility for any errors or omissions which may
appear in this document nor does it make a commitment to update the
information contained herein.
Third-party brands and names are the property of their respective owners.
Sound Blaster is a registered trademark of Creative Technology Ltd in the
United States and certain other countries. Sound Blaster-LINK and SB-LINK
are trademarks of Creative Technology Ltd.
Jan. 7, 2000 Taipei, Taiwan

Quick Installation Guide
2
I. Quick Installation Guide :
CPU SPEED SETUP
Thesystembusfrequencycanbeswitchedat66MHz,100MHzand133MHzby
adjusting DIP SW2. The CPU frequency ratio can be switched from X3 to X9.5
by adjusting DIP SW1. The user can set up CPU speed for 300-733MHz
processors by adjusting SW1 and SW2 properly.
M The CPU speed must match with the frequency RATIO. It will cause
system hanging up if the frequency RATIO is higher than CPU's.
SW1:(O:ON / X:OFF)
DIP SWITCH (SW1)
FREQ. RATIO 1234
X 3 OXOO
X 3.5 XXOO
X 4 OOXO
X4.5 XOXO
X 5 OXXO
X 5.5 XXXO
X 6 OOOX
X 6.5 XOOX
X 7 OXOX
X 7.5 XXOX
X 8 OOXX
X 8.5 XOXX
X 9 OXXX
X 9.5 XXXX
Set System Bus Speed
SW 2 :
CPU PCI 123456
AUTO 33.3 XXXXOO
66 33.3 OOXXXX
75 37.5 OOOXXX
83 41.6 OOXOXX

6VA7+
3
100 33.3 OXXXXX
112 37.5 OXOXXX
124 31 XXXOXX
133 33.3 XXXXXX
140 37.5 XXOOXX
150 35 XXOXXX
« Note: Please set the CPU host frequency in accordance with your
processor’s specifications. We don’t recommend you to set the
system bus frequency over the CPU’s specification because
these specific bus frequencies are not the standard
specifications for CPU, chipset and most of the peripherals.
Whether your system can run under these specific bus
frequencies properly will depend on your hardware
configurations, including CPU, Chipsets, SDRAM,
Cards….etc.
F For Auto Jumper setting:
SW2 ON
6 54
321
« Note: If you use 66, 100, 133 MHz CPU, we recommend you to set up
your system speed to “Auto” value.

Quick Installation Guide
4
1. CeleronTM 300A / 66MHz FSB
6VA7+
VIA
VT82C596
VIA
VT82C693
Winbond
83977
BIOS
CPU
SW1
ON 1
23
4
SW2 ON
6 54
321
SW2 ON
6 54
321
or
Auto
2. CeleronTM 333 / 66MHz FSB
3. CeleronTM 366 / 66MHz FSB
4. CeleronTM 400 / 66MHz FSB
SW1
ON 12 3
4
SW2
ON
65 4
3
1
2
SW1
ON 12
3 4
SW2
ON
65 4
3
1
2
SW1
ON 12 3
4
SW2
ON
65 4
3
1
2
SW2
ON
6
5
4 3
1
2
or
Auto
SW2
ON
65
4312
or
Auto
SW2
ON
65
4312
or
Auto

6VA7+
5
5. CeleronTM 433 / 66MHz FSB
6. CeleronTM 466 / 66 MHz FSB
7. CeleronTM 500 / 66 MHz FSB
8. CeleronTM 533 / 66 MHz FSB
9. CeleronTM 566 / 66 MHz FSB
SW1
ON 12 3
4
SW2
ON
65 4
3
1
2
SW1
ON 12 3
4
SW2
ON
65 4
3
12
SW1
ON 12 3
4
SW2
ON
65 4
3
1
2
SW1
ON 12 3
4
SW2
ON
65 4
3
1
2
SW1
ON 12 3 4
SW2
ON
65
4 3
1
2
SW2
ON
65 4
3
1
2
or
Auto
SW2
ON
65 4
3
1
2
or
Auto
SW2
ON
65 4 312
or
Auto
SW2
ON
6
5
4 3
1
2
or
Auto
SW2
ON
65
4312
or
Auto

Quick Installation Guide
6
10. Cyrix Joshua 300 / 100 MHz FSB
11. Coppermine 500 / 100MHz FSB
12. Coppermine 550 / 100MHz FSB
13. Coppermine 600 / 100MHz FSB
14. Coppermine 650 / 100MHz FSB
SW1
ON 12
3 4
SW2
ON
65
4 3
12
SW1
ON 12 3
4
SW2
ON
65
431
2
SW1
ON 12
3 4
SW2
ON
65
431 2
SW1
ON 12 3
4
SW2
ON
65
4 3
12
SW1
ON 12 3
4
SW2
ON
65 4
3
1
2
SW2
ON
65 4
3
1
2
or
Auto
SW2
ON
65
43
12
or
Auto
SW2
ON
65 4
3
1
2
or
Auto
SW2
ON
65
43
12
or
Auto
SW2
ON
65
43
12
or
Auto

6VA7+
7
15. Coppermine 700 / 100MHz FSB
16. Coppermine 533 / 133MHz FSB
17. Coppermine 600 / 133MHz FSB
18. Coppermine 667 / 133MHz FSB
19. Coppermine 733 / 133MHz FSB
SW2
ON
65 4
3
12
SW2
ON
65 4
3
12
SW1
ON 1
2
3 4
SW2
ON
65 4
3
12
SW1
ON 12
3 4
SW2
ON
65 4
3
12
SW1
ON 12
3 4
SW1
ON 12
3 4
SW2
ON
65 4
3
12
SW1
ON 12
3 4
SW2
ON
65 4
3
1
2
or
Auto
SW2
ON
65
43
12
or
Auto
SW2
ON
65
43
12
or
Auto
SW2
ON
65 4 312
or
Auto
SW2
ON
65
4 3
1
2
or
Auto

Quick Installation Guide
8
II. Jumper setting :
IR : Infrared Connector (Optional)
6VA7+
VIA
VT82C596
VIA
VT82C693
Winbond
83977
BIOS
CPU
+
Pin No. Function
1IR Transmitter Output
2GND
3IR Receiver Input
4NC
5VCC(+5V)
PWR : Power LED Connector