Gigabyte GA-8I915P Dual Graphic User manual

Table of Contents
Configuring SATA Hard Drive(s) (Controller Intel ICH6R) ......................................................... 2
(1) Installing SATA hard drive(s) in your computer .......................................................................... 2
(2) Configuring SATA controller mode and boot sequence in BIOS Setup .................................... 3
(3) Configuring RAID set in RAID BIOS ............................................................................................. 5
(4) Making a SATA Driver Disk ........................................................................................................... 9
(5) Installing SATA controller driver during OS installation ............................................................. 11

SATA Hard Drives Configurations (Intel ICH6R) - 2 -
Ác
Åé
¤¤
¤å
Configuring SATA Hard Drive(s) (Controller Intel ICH6R)
"*" Skip this step if you do not want to create RAID array on the SATA controller
To configure SATA hard drive(s), follow the steps below:
(1) Install SATA hard drive(s) in your system.
(2) Configure SATA controller mode and boot sequence in BIOS Setup.
(3)* Configure RAID set in RAID BIOS.
(4) Make a floppy disk containing the SATA controller driver.
(5) Install the SATA controller driver during OS installation.
Before you begin
Please prepare:
(a) Two SATA hard drives (to ensure optimal performance, it is recommended that you use two hard
drives with identical model and capacity). If you do not want to create RAID with the SATA
controller, you may prepare only one hard drive.
(b) An empty formatted floppy disk.
(c) Windows XP/2000 setup disk.
(d) Driver CD for your motherboard.
(1) Installing SATA hard drive(s) in your computer
Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available
SATA port(s) on the motherboard. (If there are more than one SATA controller on your motherboard, you
may check the name of the SATA connector to identify the SATA controller for the connector. For
example, SATA0_SB/SATA_SB is controlled by the SATA controller on South-Bridge.) Then connect the
power connector from your power supply to the hard drive.

SATA Hard Drives Configurations (Intel ICH6R)- 3 -
(2) Configuring SATA controller mode and boot sequence in BIOS Setup
You have to make sure whether the SATA controller is configured correctly in system BIOS Setup and
set BIOS boot sequence for the SATA hard drive(s).
Step 1:
Turn on your computer and press Del to enter BIOS Setup during POST (Power-On Self Test). If you want
to create RAID, set SATA RAID/AHCI Mode under the Integrated Peripherals menu to RAID (Disabled
by default). Then, set On-Chip SATA Mode to Manual or Auto (default) based on your own
requirements.
Figure 1
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Integrated Peripherals
KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F3: Language F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
`
The BIOS Setup menus described in this section may not show the exact settings for your
motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard
you have and the BIOS version.

SATA Hard Drives Configurations (Intel ICH6R) - 4 -
Ác
Åé
¤¤
¤å
Step 2:
Later, select Hard Disk Boot Priority under the Advanced BIOS Features menu. In the Hard Disk
Boot Priority submenu, select the model of the SATA hard drive onto which you intent to install Microsoft
Windows 2000/XP (Figure 2).
Figure 2
Step 4:
Save and exit BIOS Setup.
Figure 3
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Hard Disk Boot Priority
KL
``
K L
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Advanced BIOS Features
`
KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F3: Language F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
`
Step 3:
Set First Boot Device under the Advanced BIOS Features menu to CD-ROM to boot from CD-ROM
after system restarts (Figure 3).

SATA Hard Drives Configurations (Intel ICH6R)- 5 -
(3) Configuring RAID set in RAID BIOS
Enter the RAID BIOS setup utility to configure a RAID array. Skip this step and proceed to Section 4 if
you do not want to create RAID.
Step 1:
After the POST memory test begins and before the operating system boot begins, look for a message
which says "Press <Ctrl-I> to enter Configuration utility" (Figure 4). Press CTRL+ I to enter the RAID BIOS
setup utility.
Figure 4
Step 2
After you press CTRL+ I, the Create RAID Volume screen will appear (Figure 5).
Create RAID Volume
If you want to create RAID array, select Create RAID Volume in Main Menu and press ENTER.
Figure 5
KL

SATA Hard Drives Configurations (Intel ICH6R) - 6 -
Ác
Åé
¤¤
¤å
Step 4:
Set the stripe block size (Figure 7). The KB is the standard unit of stripe block size. The stripe block size
can be set from 4KB to 128KB. After the setting, press ENTER to set array capacity.
Figure 7
Figure 6
Step 3:
After entering the Create Volume Menu screen, name the disk array with 1~16 letters (letters cannot be
special characters) under the Name item. When finished, press ENTER to select a RAID level (Figure
6). There are two RAID levels: RAID0(Stripe) and RAID1(Mirror). Select a RAID level and press ENTER.
KL
KL

SATA Hard Drives Configurations (Intel ICH6R)- 7 -
Step 6:
When prompted to confirm whether to create this volume, press Y to create or N to cancel.
Figure 8
Step 5:
After setting all the items above, select Create Volume and press ENTER (Figure 8) to begin the creation
of the RAID array.
KL
Figure 9
KL

SATA Hard Drives Configurations (Intel ICH6R)- 8 -
After the creation is completed, you can see detailed information about the RAID Array in the DISK/VOLUME
INFORMATION section, including RAID mode, disk block size, disk name, and disk capacity, etc.
To exit the ICH6R RAID BIOS utility, press ESC in Main Menu.
Now, you can proceed to the installation of the SATA driver and operating system.
Delete RAID Volume
If you want to delete a RAID volume, select the Delete RAID Volume option in Main Menu. Press ENTER
and follow on-screen instructions.
Figure 10
KL
KL

SATA Hard Drives Configurations (Intel ICH6R) - 9 -
Ác
Åé
¤¤
¤å
Figure 11
Figure 12
(4) Making a SATA Driver Disk
To install Windows 2000/XP onto a SATA hard drives on the ICH6R controller successfully, you need
to install required driver for the SATA controller during OS installation. Without the driver, the hard drives
may not be recognized during the Windows setup process.
First of all, you need to copy the driver for the SATA controller from the motherboard driver CD to a
floppy disk. The instructions below explain how to copy the driver.
Step 1: Find an available system and insert the motherboard driver CD into the CD-ROM drive. The
installation utility will appear automatically. Quit the installation utility first.
Step 2: Go to My Computer and right-click the CD-ROM drive icon and select Open (Figure 11).
Step 3: Go to the BootDrv folder and look for an executable program named MENU.exe (Figure 12).

SATA Hard Drives Configurations (Intel ICH6R)- 10 -
Figure 14
Figure 13
Step 5:
Insert an empty floppy disk and press 1 to select 1)Intel Application Accelerator 4.0. Then it will take
about one minute to copy the SATA driver from the motherboard driver CD to the floppy disk.
Step 6:
Press 0to exit when the procedure is complete (Figure 14). You have copied the SATA driver sucessfully.
Step 4:
Double-click MENU.exe. An MS-DOS prompt screen similar to Figure 13 below will appear.