Gigabyte MU92-TU1 User manual

MU92-TU1
Intel®Socket LGA4189 processor motherboard
User Manual
Rev. 1.0

Copyright
© 2021 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specifications and features in this manual may be made by GIGABYTE
without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or
published in any form or by any means without GIGABYTE's prior written permission.
Documentation Classications
In order to assist in the use of this product, GIGABYTE provides the following types of documentation:
 UserManual:detailedinformation&stepsabouttheinstallation,congurationandusethis
product (e.g. motherboard, server barebones), covering hardware and BIOS.

User Guide: detailed information about the installation & use of an add-on hardware or
  softwarecomponent(e.g.BMCrmware,rail-kit)compatiblewiththisproduct.
Quick Installation Guide: a short guide with visual diagrams that you can reference easily for
installation purposes of this product (e.g. motherboard, server barebones).
Please see the support section of the online product page to check the current availability of these
documents
For More Information
Forrelatedproductspecications,thelatestrmwareandsoftware,andotherinformation,pleasevisit
our website at: http://www.gigabyte.com.
For GIGABYTE distributors and resellers, additional sales & marketing materials are available from our
reseller portal: http://reseller.b2b.gigabyte.com
For further technical assistance, please contact your GIGABYTE representative or visit
http://esupport.gigabyte.com/ to create a new support ticket.
For any general sales or marketing enquires, you may message GIGABYTE server directly by
email: server[email protected].

- 3 -
Table of Contents
MU92-TU1 Motherboard Layout......................................................................................5
Block Diagram .................................................................................................................7
Chapter 1 Hardware Installation .....................................................................................8
1-1 Installation Precautions.................................................................................... 8
1-2 ProductSpecications...................................................................................... 9
1-3 Installing and Removing the CPU and Heat Sink........................................... 11
1-4 Installing and Removing Memory................................................................... 12
1-4-1 8-ChannelMemoryConguration..........................................................................12
1-4-2 Installing and Removing a Memory Module ..........................................................13
1-4-3 Memory Population Table ......................................................................................13
1-4-4 DDR4 DIMM with Intel OptaneTM PMem 200 series memory population...............14
1-4-5 Intel OptaneTMPMem200seriesmatrixconguration...........................................14
1-5 Installing the M.2 SSD Module....................................................................... 15
1-6 Back Panel Connectors.................................................................................. 16
1-7 Internal Connectors........................................................................................ 17
1-8 Jumper Settings ............................................................................................. 26
Chapter 2 BIOS Setup ..................................................................................................28
2-1 The Main Menu .............................................................................................. 30
2-2 Advanced Menu ............................................................................................. 33
2-2-1 Trusted Computing .................................................................................................34
2-2-2 Serial Port Console Redirection .............................................................................35
2-2-3 SIOConguration...................................................................................................39
2-2-4 PCI Subsystem Settings.........................................................................................40
2-2-5 USBConguration..................................................................................................41
2-2-6 NetworkStackConguration..................................................................................42
2-2-7 PostReportConguration ......................................................................................43
2-2-8 NVMeConguration ...............................................................................................44
2-2-9 ChipsetConguration.............................................................................................45
2-2-10 TlsAuthConguration ............................................................................................46
2-2-11 iSCSIConguration................................................................................................47
2-2-12 Intel(R) X710 Ethernet Network Connection ..........................................................48
2-2-13 VLANConguration................................................................................................50
2-2-14 Driver Health...........................................................................................................51
2-3 Chipset Menu................................................................................................. 52
2-3-1 ProcessorConguration.........................................................................................53
2-3-2 CommonRefCodeConguration ...........................................................................56

- 4 -
2-3-3 UPIConguration ...................................................................................................57
2-3-4 MemoryConguration ............................................................................................58
2-3-5 IIOConguration ....................................................................................................61
2-3-6 AdvancedPowerManagementConguration........................................................63
2-3-7 PCHConguration..................................................................................................65
2-3-8 MiscellaneousConguration ..................................................................................67
2-3-9 ServerMEConguration ........................................................................................68
2-3-10 Runtime Error Logging Settings .............................................................................69
2-3-11 Power Policy...........................................................................................................71
2-4 Server Management Menu............................................................................. 73
2-4-1 System Event Log ..................................................................................................75
2-4-2 View FRU Information ............................................................................................76
2-4-3 BMCVLANConguration.......................................................................................77
2-4-4 BMCNetworkConguration...................................................................................78
2-4-5 IPv6BMCNetworkConguration...........................................................................79
2-5 Security Menu ................................................................................................ 80
2-5-1 Secure Boot ...........................................................................................................81
2-6 Boot Menu...................................................................................................... 84
2-7 Save & Exit Menu........................................................................................... 86
2-8 BIOS POST Beep code (AMI standard)......................................................... 88
2-8-1 PEI Beep Codes.....................................................................................................88
2-8-2 DXE Beep Codes ...................................................................................................88

- 5 -
MU92-TU1 Motherboard Layout
CPU0
DIMM_P0_A0 DIMM_P0_A1 DIMM_P0_B0 DIMM_P0_B1 DIMM_P0_D0 DIMM_P0_D1 DIMM_P0_C0 DIMM_P0_C1 DIMM_P0_H1 DIMM_P0_H0 DIMM_P0_G1 DIMM_P0_G0 DIMM_P0_E1 DIMM_P0_E0 DIMM_P0_F1 DIMM_P0_F0
1 2 3 4 5
6
7
8
9
10
11
12
13
17
18
19
20
21
22
23 24
25
26
27
28 29 30 31 32 33 34 35
37 38 39
14 15
16
36

- 6 -
Item Code Description
1 SW_ID ID Button with LED
2 USB3_MLAN Server Management LAN Port (Top)/USB 3.0 Ports (Bottom)
3 LAN1 10GbE LAN Port #1
4 LAN2 10GbE LAN Port #2
5 COM1_VGA Serial Port (Top)/VGA Port (Bottom)
6 SPI_TPM TPM Connector
7 SYS_FAN5 System Fan Connector #5
8 SYS_FAN4 System Fan Connector #4
9 P12V_AUX2 2x4 Pin 12V Power Connector (for Memory)
10 PMBUS PMBus Connector
11 ATX1 2x12 Pin Main Power Connector
12 BAT Battery Socket
13 CPU0_FAN1 CPU Fan Connector #1
14 CPU0_FAN2 CPU Fan Connector #2
15 SL_SATA2 Slimline Connector #2 (SATA 6Gb/s Signal)
16 SL_SATA1 Slimline Connector #1 (SATA 6Gb/s Signal)
17 SSATA5 SATA III 6Gb/s Connector #5
18 SSATA4 SATA III 6Gb/s Connector #4
19 SSATA_SGP1 SATA SGPIO Connector
20 P12V_AUX1 2x4 Pin 12V Power Connector (for CPU)
21 FP_1 Front Panel Header
22 F_USB3 Front Panel USB 3.0 Connector
23 BP_1 HDD Back Plane Board Connector
24 M2_0 M.2 Slot (PCIe Gen3 x4, Support NGFF-2280/22110)
25 SYS_FAN3 System Fan Connector #3
26 SYS_FAN2 System Fan Connector #2
27 SYS_FAN1 System Fan Connector #1
28 IPMB IPMB Connector
29 PCIE_1 PCIe x16 Slot #1 (Gen4 x8)
30 PCIE_2 PCIe x16 Slot #2 (Gen4 x16)
31 PCIE_3 PCIe x16 Slot #3 (Gen4 x8)
32 PCIE_4 PCIe x16 Slot #4 (Gen4 x16)
33 PCIE_5 PCIe x16 Slot #5 (Gen4 x8)
34 PCIE_6 PCIe x16 Slot #6 (Gen4 x16)
35 PCIE_7 PCIe x16 Slot #7 (Gen4 x16)
36 CN_NCSI NCSI Connector
37 LED_BMC BMC Firmware Readiness LED
38 CASE_OPEN Case Open Intrusion Alert Header
39 SW_RAID SATA RAID Upgrade Key

- 7 -
Block Diagram

Hardware Installation - 8 -
1-1 Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can
become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read
the user's manual and follow these procedures:
• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty validation.
• Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
• When connecting hardware components to the internal connectors on the motherboard,
make sure they are connected tightly and securely.
• When handling the motherboard, avoid touching any metal leads or connectors.
• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist
strap,keepyourhandsdryandrsttouchametalobjecttoeliminatestaticelectricity.
• Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
• Before unplugging the power supply cable from the motherboard, make sure the power
supply has been turned off.
• Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
• Before using the product, please verify that all cables and power connectors of your
hardware components are connected.
• To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
• Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
• Do not place the computer system on an uneven surface .
• Do not place the computer system in a high-temperature environment.
• Turning on the computer power during the installation process can lead to damage to
system components as well as physical harm to the user.
• If you are uncertain about any installation steps or have a problem related to the use of the
product,pleaseconsultacertiedcomputertechnician.
• To avoid any potential short circuit of the DIMM slots, please remove any stand-offs from the
chassis that will be located underneath the DIMM slots, before installing the motherboard
into the chassis.
Chapter 1 Hardware Installation

- 9 - Hardware Installation
1-2 Product Specications
Form Factor E-ATX
305W x 330D (mm)
CPU 3rd Generation Intel® Xeon® Scalable Processors
Intel® Xeon® Platinum Processor, Intel® Xeon® Gold Processor,
Intel® Xeon® Silver Processor, Intel® Xeon® W-3300 Processor
10nm technology, CPU TDP up to 270W
1 x LGA 4189; Socket P+
Chipset Intel® C621A Express Chipset
Memory 16 x DIMM slots
DDR4 memory supported only
8-channel memory architecture
RDIMM modules up to 64GB supported
LRDIMM modules up to 128GB supported
3DS RDIMM/LRDIMM modules up to 256GB supported
1.2V modules: 3200/2933/2666 MHz
LAN 2 x 10Gb/s BASE-T LAN ports (Intel® X710-AT2)
1 x 10/100/1000 management LAN
Onboard
Graphics
Integrated in Aspeed® AST2600
2D Video Graphic Adapter with PCIe bus interface
1920x1200@60Hz 32bpp, DDR4 SDRAM
Storage Interface 2 x 7-pin SATA 6Gb/s ports
2 x SlimSAS with 8 x SATA 6Gb/s ports
RAID Intel® SATA RAID 0/1/10/5
Expansion Slots Slot_7: 1 x PCIe x16 (Gen4 x16 bus) slot
Slot_6: 1 x PCIe x16 (Gen4 x16 or x8 bus) slot, shared with Slot_5
Slot_5: 1 x PCIe x16 (Gen4 x0 or x8 bus) slot
Slot_4: 1 x PCIe x16 (Gen4 x16 or x8 bus) slot, shared with Slot_3
Slot_3: 1 x PCIe x16 (Gen4 x0 or x8 bus) slot
Slot_2: 1 x PCIe x16 (Gen4 x16 or x8 bus) slot, shared with Slot_1
Slot_1: 1 x PCIe x16 (Gen4 x0 or x8 bus) slot
1 x M.2 slot:
- M-key
- PCIe Gen3 x4 per slot
- Supports NGFF-22110/2280 cards
NOTE:
We reserve the right to make any changes to the product specications and product-related
information without prior notice.

Hardware Installation - 10 -
Internal I/O
Connectors
1 x 24-pin ATX main power connector
2 x 8-pin ATX 12V power connectors
2 x SlimSAS connectors
2 x 7-pin SATA connectors
1 x M.2 slot
2 x CPU fan headers
5 x System fan headers
1 x USB 3.0 header
1 x TPM header
1 x VROC connector
1 x Front panel header
1 x PMBus connector
1 x IPMB connector
1xClearCMOSjumper
1xBIOSrecoveryjumper
1 x Case open header
1 x Buzzer
Rear I/O
Connectors
2 x USB 3.0 Ports
1 x VGA Port
1 x Serial Port
2 x RJ45 Ports
1 x MLAN Port
1 x ID button with LED
TPM 1 x TPM Header with SPI Interface
Optional TPM2.0 kit: CTM010
Board
Management
Aspeed® AST2600 Management Controller
GIGABYTE Management Console (AMI MegaRAC SP-X) Web Interface
Operating
Properties Operating temperature: 10°C to 40°C
Operating humidity: 8-80% (non-condensing)
Non-operating temperature: -40°C to 60°C
Non-operating humidity: 20%-95% (non-condensing)

- 11 - Hardware Installation
1
1-3 Installing and Removing the CPU and Heat Sink
Read the following guidelines before you begin to install the CPU:
• Make sure that the motherboard supports the CPU.
• Always turn off the computer and unplug the power cord from the power outlet before installing
the CPU to prevent hardware damage.
• Unplug all cables from the power outlets.
• Disconnect all telecommunication cables from their ports.
• Placethesystemunitonaatandstablesurface.
• Open the system according to the instructions.
WARNING!
Failure to properly turn off the server before you start installing components may cause serious
damage. Do not attempt the procedures described in the following sections unless you are a
qualiedservicetechnician.
P4 Socket
4
1
2
3
4
6
5
Follow these instructions to install the CPU:
1. Align and install the processor on the carrier.
NOTE: Apply thermal compound evenly on the top of the CPU. Remove the protective cover from
the underside of the heatsink.
2. Carefullyiptheheatsinkcover.Theninstallthecarrierassemblyonthebottomoftheheatsinkand
make sure the gold arrow is located in the correct direction.
3. Remove the CPU cover.
NOTE: Save the CPU cover in the event that you need to remove the CPU from the socket.
4. Align the heatsink with the CPU socket by the guide pins and make sure the gold arrow is located in
the correct direction. Then place the heatsink onto the top of the CPU socket.
5. Position the rotating wires into the latch position.
6. Tighten the screws in a sequential order (1g2g3g4).
NOTE: When dissembling the heatsink, loosen the screws in reverse order (4g3g2g1) and
then move the rotating wires into the unlatch position.
2
3

Hardware Installation - 12 -
1-4 Installing and Removing Memory
Read the following guidelines before you begin to install the memory:
•Make sure that the motherboard supports the memory. It is recommended to use memory of the
same capacity, brand, speed, and chips.
•Always turn off the computer and unplug the power cord from the power outlet before installing
the memory to prevent hardware damage.
•Memory modules have a foolproof design. A memory module can be installed in only one
direction. If you are unable to insert the memory, switch the direction.
1-4-1 8-Channel Memory Conguration
This motherboard provides 16 DDR4 memory sockets and supports 8-Channel Technology. After the memory
isinstalled,theBIOSwillautomaticallydetectthespecicationsandcapacityofthememory.
CPU0
DIMM_P0_A0 DIMM_P0_A1 DIMM_P0_B0 DIMM_P0_B1 DIMM_P0_D0 DIMM_P0_D1 DIMM_P0_C0 DIMM_P0_C1 DIMM_P0_H1 DIMM_P0_H0 DIMM_P0_G1 DIMM_P0_G0 DIMM_P0_E1 DIMM_P0_E0 DIMM_P0_F1 DIMM_P0_F0

- 13 - Hardware Installation
1-4-2 Installing and Removing a Memory Module
Before installing a memory module, make sure to turn off the computer and unplug the
power cord from the power outlet to prevent damage to the memory module.
Be sure to install DDR4 DIMMs on this motherboard.
1
2
2
Follow these instructions to install a DIMM module:
1. Insert the DIMM memory module vertically into the DIMM slot and push it down.
2. Close the plastic clip at both edges of the DIMM slots to lock the DIMM module.
3. Reverse the installation steps when you want to remove the DIMM module.
1-4-3 Memory Population Table
Note: DIMM must be populated in sequential alphabetic order, starting with bank A0.
Type Ranks Per DIMM and
Data Width
DIMM Capacity (GB)
Speed (MT/s); Voltage (V);
Slots per Channel(SPC) and
DIMM per Channel (DPC)
1DPC 2DPC
8Gb 16Gb 1.2V 1.2V
RDIMM SRx8 8GB 16GB
3200 3200
RDIMM SRx4 16GB 32GB
RDIMM DRx8 16GB 32GB
RDIMM DRx4 32GB 64GB
RDIMM 3DS (4R/8R)x4 2H-64GB
4H-128GB
2H-128GB
4H-256GB
LRDIMM QRx4 64GB 128GB 3200 3200
LRDIMM 3DS (4R/8R)x4 4H-128GB 2H-128GB
4H-256GB 3200 3200

Hardware Installation - 14 -
1-4-4 DDR4 DIMM with Intel OptaneTM PMem 200 series memory population
DIMM Type Ranks Per DIMM and
Data Width
DIMM Capacity (GB)
8Gb 16Gb
RDIMM
(SMT-up to 3200)
1Rx8 N/A N/A
1Rx4 16GB 32GB
2Rx8 16GB 32GB
2Rx4 32GB 64GB
RDIMM 3DS
(SMT-up to 3200)
4Rx4 (2H) N/A 128GB
8Rx4 (4H) N/A 256GB
LRDIMM
(SMT-up to 3200) 4Rx4 64GB 128GB
LRDIMM 3DS
(SMT-up to 3200)
4Rx4 (2H) N/A N/A
8Rx4 (4H) N/A 256GB
1-4-5 Intel OptaneTM PMem 200 series matrix conguration
DDR4+PMemMode AD
Interleave DIMM_P0_F0 DIMM_P0_F1 DIMM_P0_E0 DIMM_P0_E1 DIMM_P0_H0 DIMM_P0_H1 DIMM_P0_G0 DIMM_P0_G1 DIMM_P0_C1 DIMM_P0_C0 DIMM_P0_D1 DI MM_P0_D0 DIMM_P0_A1DIMM_P0_A0DIMM_P0_B1DIMM_P0_B0
One - x4PMem DDR4PMem DDR4 DDR4PMem DDR4PMem
One - x4DDR4PMem DDR4PMem PMem DDR4PMem DDR4
4RDD4RDD DDR4DDR4PMem 4RDD4RDD
4RDD4RDD4RDD 4RDD4RDD4RDD PMem
4RDD4RDD PMem DDR4 DDR4 4RDD4RDD
PMem 4RDD4RDD4RDD 4RDD4RDD4RDD
4RDD4RDD4RDD PMem 4RDD4RDD4RDD
DDR4 4RDD4RDD 4RDD4RDD PMem DDR4
4RDD4RDD4RDD PMem 4RDD4RDD4RDD
DDR4PMem 4RDD4RDD 4RDD4RDD DDR4
4RDD4RDD4RDD4RDD 4RDD4RDD PMem 4RDD4RDD
4RDD4RDD4RDD4RDD PMem 4RDD4RDD4RDD4RDD
4RDD4RDD PMem 4RDD4RDD 4RDD4RDD4RDD4RDD
4RDD4RDD4RDD4RDD PMem 4RDD4RDD4RDD4RDD
4RDD
4RDD4RDD4RDD DDR4PMem 4RDD4RDD4RDD
4RDD4RDD4RDD4RDD 4RDD4RDD4RDD PMem DDR4
DDR4PMem 4RDD4RDD4RDD 4RDD4RDD4RDD4RDD
4RDD4RDD4RDD PMem DDR4 4RDD4RDD4RDD4RDD
One - x4 4RDD4RDD PMem 4RDD4RDD PMem PMem 4RDD4RDD PMem 4RDD4RDD
4RDD4RDD PMem DDR4PMem DDR4 DDR4PMem DDR4PMem 4RDD4RDD
DDR4PMem 4RDD4RDD4RDD PMem PMem 4RDD4RDD4RDD PMem DDR4
One - x4 DDR4PMem 4RDD4RDD PMem DDR4 DDR4PMem 4RDD4RDD PMem DDR4
8+8AD,MMOne - x8 DDR4PMem DDR4PMem DDR4PMem DDR4PMem PMem DDR4PMem DDR4PMem DDR4PMem DDR4
4+4AD,MM
CPU0
6+1ADOne - x1
8+1 AD One - x1
8+4AD,MM Two - x2
Note:
• AD (App Direct Mode)
»Min 1 PMem anywhere on platform.
»Intel recommands DRAM to PMem 200 series ratio is between 1:1 and 1:8.
• MM (Memory Mode)
»Population DRAM across all available DDR Channels to maximize bandwidth.
»Intel recommands DRAM to PMem 200 series NM/FM ratio is between 1:4 and 1:16.
(NM=Near Memory; FM = Far Memory)
• No mixing of PMem and NVDIMMs within the platform.
• For each individual population, different permutations (PMem rearrangements among channels) are
permittedsolongasthecongurationdoesn'tbreakDDR4DIMMpopulationrules.
• Ensure the same DDR4 DIMM type and capacity are used for each DDR4 + PMem population.
• Ifsystemdetectsanun-validatedPORconguration,thensystemissuesaBIOSwarning.

- 15 - Hardware Installation
1-5 Installing the M.2 SSD Module
Follow the steps below to install a M.2 SSD module on your motherboard.
Step1. Insert the M.2 SSD module into the slot.
Step2. Secure it with the screw, tightening as necessary to fasten the M.2 SSD module in place.
1
2

Hardware Installation - 16 -
1-6 Back Panel Connectors
uSerial Port
Connects to serial-based mouse or data processing devices.
vVGA Port
Connect to a monitor device.
w10GbE LAN Port #2
The 10 Gigabit Ethernet LAN port provides Internet connection at up to 10 Gbps data rate. See the
section below for a description of the states of the LAN port LEDs.
x10GbE LAN Port #1
The 10 Gigabit Ethernet LAN port provides Internet connection at up to 10 Gbps data rate. See the
section below for a description of the states of the LAN port LEDs.
yServer Management LAN Port
The LAN port provides Internet connection with data transfer speeds of 10/100/1000Mbps. This port is
the dedicated LAN port for Server Management.
zUSB 3.0 Ports
The USB port supports the USB 3.0 specification. Use this port for USB devices such as a USB
keyboard/mouse,USBprinter,USBashdriveetc.
{ID button with LED
Whenthesystemidenticationisactive,theIDLEDonthefront/backpanelglowsblue.
• Whenremovingthecableconnectedtoabackpanelconnector,rstremovethecablefromyour
device and then remove it from the motherboard.
• When removing the cable, pull it straight out from the connector. Do not rock it side to side to
prevent an electrical short inside the cable connector.
1
2
3 4
5
67
LAN and ID Button LEDs
Link/Activity LED
Speed LED
LAN Port
ID button/LED:
10/100/1000 LAN LED:
State Description
Yellow On 1Gbps data rate
Green On 100Mbps data rate
Off 10Mbps data rate
State Description
Blue On Systemidenticationisactive
Off Systemidenticationisdisabled
10GbE LAN LED:
State Description
Yellow On 5Gbps, 2.5Gbps, 1Gps data rate
Green On 10Gbps data rate
Off 100Mbps data rate

- 17 - Hardware Installation
1-7 Internal Connectors
Read the following guidelines before connecting external devices:
• First make sure your devices are compliant with the connectors you wish to connect.
• Before installing the devices, be sure to turn off the devices and your computer. Unplug the power
cord from the power outlet to prevent damage to the devices.
• After installing the device and before turning on the computer, make sure the device cable has
been securely attached to the connector on the motherboard.
1) ATX1 11) PMBUS
2) P12V_AUX1 (for CPU) 12) F_USB3
3) P12V_AUX2 (for Memory) 13) FP_1
4) SSATA5 14) BP_1
5) SSATA4 15) SPI_TPM
6) SSATA_SGP1 16) IPMB
7) SW_RAID 17) CN_NCSI
8) CPU0_FAN1/2 18) LED_BMC
9) SYS_FAN4/5 19) BAT
10) SYS_FAN1/2/3 20) CASE_OPEN
CPU0
DIMM_P0_A0 DIMM_P0_A1 DIMM_P0_B0 DIMM_P0_B1 DIMM_P0_D0 DIMM_P0_D1 DIMM_P0_C0 DIMM_P0_C1 DIMM_P0_H1 DIMM_P0_H0 DIMM_P0_G1 DIMM_P0_G0 DIMM_P0_E1 DIMM_P0_E0 DIMM_P0_F1 DIMM_P0_F0
1
2
3
4
5
6
8
9
11
18
19
20
15
16
7
10
12
13
14
17

Hardware Installation - 18 -
1/2/3) ATX1/P12V_AUX1/P12V_AUX2
(2x12 Main Power Connector and 2x4 12V Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the components
onthemotherboard.Beforeconnectingthepowerconnector,rstmakesurethepowersupplyisturnedoff
and all devices are properly installed. The power connector possesses a foolproof design. Connect the power
supply cable to the power connector in the correct orientation. The 12V power connector mainly supplies
power to the CPU. If the 12V power connector is not connected, the computer will not start.
To meet expansion requirements, it is recommended that a power supply that can withstand high
power consumption be used (500W or greater). If a power supply is used that does not provide the
required power, the result can lead to an unstable or unbootable system.
ATX1
P12V_AUX1/P12V_AUX2
8
5
4
1
PinNo. Denition
1 GND
2 GND
3 GND
4 GND
5 +12V
6 +12V
7 +12V
8 +12V
Pin No. Denition Pin No. Denition
1 3.3V 13 3.3V
2 3.3V 14 -12V
3 GND 15 GND
4 +5V 16 PS_ON
5 GND 17 GND
6 +5V 18 GND
7 GND 19 GND
8 Power Good 20 -5V
9 5VSB 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
12 3.3V 24 GND
113
1224

- 19 - Hardware Installation
4/5) SSATA5/SSATA4 (SATA III 6Gb/s Connectors)
The SATA connectors conform to SATA III 6Gb/s standard and are compatible with SATA 3Gb/s standard.
Each SATA connector supports a single SATA device.
PinNo. Denition
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
1
7
6) SSATA_SGP1 (SATA SGPIO) Connector
Serial General Purpose Input/Output (SGPIO) is a communication method used between a host bus adapter
(HBA) and a main board.
Pin No. Denition
1 Data Out
2 GND
3 Data In
4 Load
5 Clock
1
5

Hardware Installation - 20 -
7) SW_RAID (SATA RAID Upgrade Key)
8/9/10) CPU0_FAN1/CPU0_FAN2/SYS_FAN1/SYS_FAN2/SYS_FAN3/SYS_FAN4/SYS_FAN5
(CPU Fan/System Fan Headers)
The motherboard has one 4-pin CPU fan header (CPU_FAN), and two 4-pin (SYS_FAN) system fan headers.
Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect
it in the correct orientation (the black connector wire is the ground wire). The motherboard supports CPU
fan speed control, which requires the use of a CPU fan with fan speed control design. For optimum heat
dissipation, it is recommended that a system fan be installed inside the chassis.
1
1
PinNo. Denition
1 GND
2 +12V
3 Sense
4 Speed Control
•Be sure to connect fan cables to the fan headers to prevent your CPU and system from
overheating. Overheating may result in damage to the CPU or the system may hang.
• Thesefanheadersarenotconfigurationjumperblocks.Donotplacea jumpercaponthe
headers.
4
1
Pin No. Denition
1 GND
2 P_3V3_AUX
3 GND
4 PCH_SATA_RAID_KEY