Giken Trastem VC-1020 User manual

CONFIDENTIAL
VC-1020 Sensor Unit
Installation Manual
Contents
1. SAFETYINDICATIONS...............................................................................................................................2
2. INTRODUCTION..........................................................................................................................................1
3. SYSTEM DIAGRAM / INSTALLATION WORK DETAILS.........................................................................1
4. SENSOR UNITINSTALLATIONANDWIRING.........................................................................................2
5. SENSOR INSTALLATION LOCATION EXAMPLE....................................................................................4
6. SENSOR DESCRIPTION............................................................................................................................6
7. SENSOR UNITINSTALLATION.................................................................................................................7
8. WEB SETTINGS........................................................................................................................................11
9. CONNECTTO NETWORK....................................................................................................................... 11
10. SENSOR UNITSPECIFICATIONS..........................................................................................................12
11. REMARKS FOR POE (POWEROVER ETHERNET)SWITCHINGHUB............................................13
System :
VC-1020 Sensor Unit
Issued :
Nov. 25th 2015 [2nd Edition]
Issued by :
Giken Trastem Co., Ltd.
Distribution to:
Sensor Installer, Installation Engineer
Version:
IM-VC1020-1511-2-EN

CONFIDENTIAL
1. SAFETYINDICATIONS
This section provides notes to use the product safely. Please read this section carefully to ensure proper and safe
use of the product.
FCC Part 15 Subpart B Class A
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference.
(2)This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
isoperated in a commercial environment. This equipment generates, uses, and can radiate radio frequencyenergy and, if
not installed and used in accordance with the instruction manual, maycause harmful interference to radio
communications. Operation of thisequipment in a residentialarea is likelyto cause harmfulinterference in which case the
user will be required to correct the interference at his own expense.
The CEmarking indicates compliance to 2004/108/ECEMC Directive with Standards EN55022 Class A ;
EN55024
Giken Trastem assumes no responsibility ifthe installation andwiring connection whichare stated in the instruction
manual provided together with this product is not carried out, or when product without CE marking is connected to this device.
Conditions of use:
This product is not intended for use in any safety-critical or personal safetyapplication. GIKEN TRASTEM assumes no liability
for any accident resulting in personal injury, death, or property damage if this product has been used in the above conditions.

CONFIDENTIAL
1
IM-VC1020-1511-2-EN
2. INTRODUCTION
SENSORUNIT
ThesensordetectsandtracksthenumberofpeopleaccuratelyusingImageRecognitiontechnology.
The sensor is installed on the ceiling of entrances and passageways of retail, public facilities etc. to capture
movementsofpeoplefromabove.
IN and OUT traffic data is recordedto the sensorcontinuouslyevery minute and the collected data issent tothe
designatedserverviaLAN.
Trafficdatacanbecompiledandusedasmarketinginformation.
The sensor can cover movements of the people in a wide area and recognizes and tracks the movements of
peopleaccuratelythereforecanomitpeoplehoveringnearthecountingareatoprovideanaccuratetrafficcount.
This manual “PALOSSIE AIO (VC-1020 Sensor Unit) Installation Manual (Overseas)” explains the required
stepstoinstallthesystem.
Thismanualisintendedforthesystem installer.
Pleasefollowthe stepsindicatedinthismanualwheninstallingthesensorunit.
3. SYSTEM DIAGRAM /INSTALLATION WORK DETAILS
The system diagrambelowillustratesageneral system installationofa mid-scale facility.
Details of SENSOR UNIT ->PoEHUB ->Management PC connectionexample. (referto Fig. 1)
ThecablelengthfromtheSensorUnittoPoEHUBismax.100m(109.3yds).
WorkdetailsforSystemInstallation
Item
WorkDetails
Remarks
1
Signal lines, Power lines, Wire laying work according to
SystemWiring Diagram
2
SENSOR UNIT ceiling mount installation and wire
connectionwork
3
Connect LANcable
4
LocallypurchasePoEHUB
5
DataCollection,Reporting SoftwareInstallation
DataCollection,Reporting Software
(if required)
: EndUsersNetwork
ManagementPC
● Data Collection Software
● Data Reporting Software

CONFIDENTIAL
2
IM-VC1020-1511-2-EN
4. SENSORUNITINSTALLATIONANDWIRING
■Precautions
Pleasekeepthe SENSORlens freefrom anydust ordebris.
■InstallationLocationCriterion
Installthe SENSOR alongthe center of thedoor width, unless there is an object obstructing the center of the door
width.(Referto Fig.2)
1) When installing the sensor at a corridor or passageway, install the sensor in the center, between the walls or
pillars.(RefertoFig.3)
2) When installing 2 sensor units at 1 entrance (for wide entrances), divide the door width into two sections and
installthesensorsalongthecenterof eachdivided section.(RefertoFig.7)
Installable
500-1,400mm
(1.6-4.6ft)
awayfrom door
[PrecautionsforInstallation Location]
If the sensors cannot be installed according to the criteria
above, contact and check with our staff and install according to
theirdirections.
Ex)CannotinstallSENSORatthedoor width center,
ortheSENSORcannotbe installedbetweenthe
recommended500-1400mm etc.
Cannot installwithin
500mm(1.6ft)fromdoor
BestInstallation
900-1200mm
(3-3.9 ft)
awayfrom door

CONFIDENTIAL
3
IM-VC1020-1511-2-EN
NOTE:When there is an obstructing object near
the sensor, install the sensor the “same height as
object” away from the object.
Install H mm away from
object
Obstructing Object
BestInstallation
900-1,200mm (3-3.9ft)
Installable
500-1,400mm(1.6-4.6ft)
Uninstallable
within500mm
(1.6ft)
HeightHmm

CONFIDENTIAL
4
IM-VC1020-1511-2-EN
2) InstallationExamplefor Entrance/Passageway
*Thedrawing above isanexampleof anentrance with
a ceiling height over 3,000mm (9.8 ft) and a width of
lessthan 4,500mm(14.8ft).
1) InstallationExampleforPassageway
*The drawing above illustrates a passageway
betweentwo walls with aceiling height over 3,000mm
(9.8ft) anda widthlessthan4,500mm(14.8ft)
*When the installed height is less than 3,000mm the
countingwidthwill be less than 4,500mm.
5. SENSORINSTALLATIONLOCATIONEXAMPLE
3) InstallationExampleforPassageway(Installing 2SENSORS)
* The drawing above illustrates a counting area between two walls with a ceiling height of over 3,000mm (9.8 ft)
anda counting widthlessthan9,000mm(29.5ft).
*Iftheceilingheightislessthan 3,000mm (9.8ft),countingwidthis less than4,500mm (14.8ft).
Less than9,000mm
CenterofAisle
Within4,500mm
(14.8ft)
CenterofAisle
2,250mm
2,250mm
Within4500mm
(14.8 ft)
CenterofAisle
(7.4 ft)
(7.4 ft)
(29.5ft)

CONFIDENTIAL
5
IM-VC1020-1511-2-EN
*Thecountingwidthvariesaccordingtofittedheights.
Ceilingheightand DetectionArea
StandardMode
CeilingHeight
DetectionArea
2,300mm
(7.5ft)
1,800mm
(5.9ft)
~
~
3,000mm
to
4,200mm
(9.8ft–13.8ft)
4,500mm
(14.8ft)
*When the sensor is installedat less
than 3000mm, detection width
becomes almost same as
installationheight
4,200mm
3,000mm
(7.5ft)
4,500mm(14.8 ft)
1,800mm(5.9 ft)
(13.8ft)
(9.8ft)
2,300mm
HighMode
*When using high modethe
detectionareaissmaller.
CeilingHeight
DetectionArea
4,000mm
(13.1ft)
3,000mm
(9.8ft)
5,000mm
(16.4ft)
4,000mm
(13.1ft)
6,000mm
(19.7ft)
4,000mm
(13.1ft)

CONFIDENTIAL
6
IM-VC1020-1511-2-EN
6. SENSORDESCRIPTION
Sensor CoverAttached
Operation LED
Initializing :AMBER(Whenpoweredonwilltake20secondstoboot.)
Normal :GREEN ON
IN Count :REDFLASH
OUTCount :GREEN FLASH
PowerOFF :DARK
CoverRemoved
DC Jack
ACadaptercanbeconnectedwhena PoEisnot
used.
LAN/ PoE Port
PoweroverEthernetswitchinghub
(PoEHUB)isconnectedviaLAN
cable.
IPAddress ResetSwitch
*Registered IPaddress ofthesensor
canbeinitializedbyholdingdownthis
switch for5seconds orlonger.
Note:Thedefault
IP address is “192.168.0.249” /
Subnet Mask is “255.255.255.0”

CONFIDENTIAL
7
IM-VC1020-1511-2-EN
7. SENSORUNITINSTALLATION
■Removing the sensorunit cover
1) Insert your fingers in the location indicated in RED bottom of sensor and pull the cover from the unit. (Refer to
[Fig.9])
2) Completelyremovethecoverfromthesensor unit.(Referto[Fig.10])
■Wiringthesensor unit
1) Pullout theLANcable(CAT5)from thesensor unitwireholeandcutthe cableat therequiredlength.
TerminatetheLAN cablewith aRJ-45connector.Usesolidsinglecorewiresandmakeastraight throughcable.
NOTE:Testthecablewith acabletester toensurethat thecablewillfunction
Example:Straight-throughEthernetCable(T-568B)
1：WhiteOrange
2：Orange
3：WhiteGreen
4：Blue
5：WhiteBlue
6：Green
7：WhiteBrown
8：Brown
RJ45Connector
RJ45Connector

CONFIDENTIAL
8
IM-VC1020-1511-2-EN
2) Connectthe LANcable.(Referto[Fig.12])
3 )WhensupplyingpowerfromthepoweradapterwithoutusingPoE, insertthe DCjackas indicatedbelow.
(Referto[Fig.13])
NOTE: The DC jack can be used for temporary use such as during setup etc., we do not recommend supplying
thepower throughthe DCjackforpermanentinstallations.
DC24(DCJack)max.7W

CONFIDENTIAL
9
IM-VC1020-1511-2-EN
■SensorInstallation
1)There isaspecificsensormountingdirection.
TheDOORIndicator onthesensorunitindicates thedirectionto installthesensor.
Mountthesensor withtheDOORArrowpointedtowardstheentrance.
The sensor can also be installed at areas without doors such as passageways, please install in the most suitable
areainthosecases.(Referto[Fig.14])
2) Secure the sensor unit to the ceiling at 3 points with screws (board anchors or suitable screw depending on
ceiling material).
NOTE:Cablesshouldbeattachedtotheactualsensorunit.Omittedforexplanationpurposes.
Installsothatthe arrow
pointstowardstheentrance.

CONFIDENTIAL
10
IM-VC1020-1511-2-EN
■Attachingthe SensorCover
1)Aftersecurelyfixingthesensorto theceiling,reattachthecover.Hookthe covertotheunit.
(Referto[Fig.16])
(2)Attachthecovertothesensorunit.(Referto[Fig.17])
(3)Pushthecoverupuntilitissecuredtotheunit. (Push thecovertillitClicksshut.)(Refer to[Fig.18])
SensorInstallationworkis complete.

CONFIDENTIAL
11
IM-VC1020-1511-2-EN
8. WEB SETTINGS
Do NOT connect the LAN cable to the END USERS network until the SENSOR UNIT network settings
are completed.
■WebSettings.
(1)ConnectPoEinjector(HUB) to sensorunit.(Refer toFig.19)
NOTE:For someintelligentswitches itmaytakeafewminutes toestablishconnection.
(2)Thesensorwillpower up(willtake20secondstoinitialize).
While the sensor is initializing the LED will light AMBER, after the sensor is initialized the LED will turn on
GREEN.
(3)ConnectthesetupPC to sensorunit viaPoEinjector(HUB)
*NOTE:SetupPCrequirements:OperatingSystem (Windows VISTAorlater)/InternetExplorer8orlater.
*NOTE:The sensor unit default IP address is “192.168.0.249”. Please change the Setup PC network
parametersto thesameIPnetworkrangetoenablecommunicationbetweenthesetupPC
andsensor (e.g.192.168.0.250).
(4)Setup thefollowingnetwork andsensorsetupparameters.
SettheIPaddress, subnetmask,default gateway, portnumber,timesettings,sensor mountingheight,
countingarea,countingdirectionetc.
Pleaserefertothe“Web Settings Manual” for setup details.
9. CONNECT TONETWORK
Aftercompletingthewebsettings,connect theLAN cable toendusersnetwork viaPoEHUB.
(Please insertthe LANconnector, untilit clicks)
*NOTE: Upon connecting the LAN, the sensor will connect to the end user’s network. Recheck the IPAddress of the
sensor, beforeconnectingtothe network.
SetupPC
LAN
cable
SensorUnit
PoE
Injector(HUB)

CONFIDENTIAL
12
IM-VC1020-1511-2-EN
10. SENSORUNITSpecifications
SENSOR UNIT (VC-1020) Specifications
Item
Specifications
Remarks
Dimensions
W：193mm
H：85mm
D：34mm
(7.6inches)
(3.35inches)
(1.34inches)
Referto[Fig.20]
InstalledHeight
2,300mmto4,200mm
(7.5to13.8ft)
Highmode:4,000 mm to 6,000 mm
(13.1to 19.7 ft)
PowerSource
DC48V(Max.7W)
DCJack:24V
CableType
CAT5-UTP
WiringDistance
DistancetoPoEHUBwithin
100m (109.3 yds).
Connector
LANconnector
LEDIndicator
GREENON: Power ON(Normal)
AMBER :Initializing(20sec.)
DARK :PowerOFF
RED FLASH :IN
GREENFLASH:OUT
View
SideView
Ceiling
193mm
34mm
TopView
85mm
SideView
LED

CONFIDENTIAL
13
IM-VC1020-1511-2-EN
11. RemarksforPoE(PoweroverEthernet)SwitchingHub
Thesensor(VC-1020/VC-1050)requiresapowersupplyofMax. 7W foreachunit.
Please check the PoE Switching HUB specifications to ensure that the maximum power supply for each port and
theallowable total powersupplyaresufficient.
In the event the power supply is not sufficient the power to the sensor and data communication may become
unstable.
In case the sensor is connected to an existing PoE switch, make sure that there is enough power supply for each
portandthetotalpowersupplyaresufficient.
If there are any other devices connected to the existing PoE switch, calculate the remaining allowable power and
connectthesensorswithintheallowablerange.
PoESwitch Specification
(Example）
Power Supply
Requires at least 7W x (No. of Sensors)
(Example:Toconnect5units requires min.35W）
Standards
IEEE802.3af Class0
Certifications
CEStandard
Total：28W
PoESwitchingHUB
Port:5open ports
MaximumTotalSupplyBudget:30W
When 5 sensors are connected to this PoE it will exceed the PoE’s Maximum Total Power Supply (30W.)
7(W)×5(units) =35(W)
In theexample abovemaximum4sensorscanbeconnectedto this PoEswitch.
PoEHUB
VC-1020
(7W)
VC-1020
(7W)
VC-1020
(7W)
VC-1020
(7W)
VC-1020
(7W)
Total35W
OK
NG

CONFIDENTIAL
14
IM-VC1020-1511-2-EN
CONTACT DETAILS
DISTRIBUTOR
MANUFACTURER
GIKENTRASTEMCO.,LTD.
□Head Office 98 TakedaNishi-Dankawara-choFushimi-kuKyoto,Japan612-8429
TEL:[phone] FAX:[phone]
E-mail:[e-mail]
! Operating Hours(Contact)
■Weekdays: 9:00to17:30(GMT+9:00)
■Weekends/Holidays: Closed (Respondon nextworkingday.)