GILKON AXIS 8MPMFS User manual

Manufactured & Distributed By:
www.gilkonaxis.com.au
PO Box 63
Moorebank NSW 1875
337 - 349 Newbridge Road
Moorebank NSW 2170
Tel: [phone]
Fax: [phone]
Email: [e-mail]
INSTRUCTIONS
Wall Mounts
Wall Mount for Plasma Display
ProKon Plasma / LCD Wall Mounts
Wall Mounts for Plasma Displays
Assembly Instructions
D
E
S
I
G
N
E
D
&
M
A
N
U
F
A
C
T
U
R
E
D
I
N
A
U
S
T
R
A
L
I
A
Assembly instructions for the following models of the
ProKon wall mounts for plasma displays:
Model Code
Small Display 25” - 37” - Fixed 8MPMFS
Medium Display 42” - 50” - Fixed 8MPMF
Medium Display 42” - 50” - Tilt 8MPMA
Large Display 50” - 65” - Fixed 8MPMFL
Large Display 50” - 65” - Tilt 8MPMAL
Stainless Steel Finish
Small Display 25” - 37” - Fixed 8MPMFS-S
Medium Display 42” - 50” - Fixed 8MPMF-S
Medium Display 42” - 50” - Tilt 8MPMA-S
Fixed Tilt Adjustable
Adjustable Tilt
Plasma Rail
Plasma Rail Safety Lock
Wall Mount Bracket
1
Distributed By:
www.gilkon.com.au Phone: [phone] Email: [email protected]

Manufactured & Distributed By:
www.gilkonaxis.com.au
PO Box 63
Moorebank NSW 1875
337 - 349 Newbridge Road
Moorebank NSW 2170
Tel: [phone]
Fax: [phone]
Email: [e-mail]
INSTRUCTIONS
Wall Mounts
Wall Mount for Plasma Display
ProKon Plasma / LCD Wall Mounts
Wall Mounts for Plasma Displays
Assembly Instructions
1. Mark hole centres on wall.
2. Secure the Plasma Wall Mount Bracket (Item 2). Ensure anchor points are strong enough to support the plasma
bracket and the plasma screen at full extension.
NOTE: Care must be taken in assessing the wall suitability. In some cases, reinforcement of the wall may be
necessary.
3. Install the two plasma rails (Item 1) to the rear of your plasma screen using appropriate cap screws (supplied).
Ensure both rails are installed at exactly the same height.
NOTE: Ensure the screw length is the same as specified by the plasma screen manufacturer to avoid damaging
the screen.
4. Lift and attach the plasma screen, complete with rails, by hooking the rails over the plasma wall mount bracket
(Item 2). See detail 3A.
5. Horizontally adjust the plasma screen as desired and lock into position on the bottom of each rail. See detail 3B.
A
B
A
BWall Mount Bracket
Plasma Rail
Plasma Rail Safety Lock
Plasma Rail
Wall Mount Bracket
Detail 3
Plasma Rail 1
Wall Mount Bracket 2
Screen End
Detail 3
This product consists of:
1 x Template for Positioning of Mount
1 x Plasma Wall Mount Assembly
2 x Plasma Rails
6 x Washers
6 x M8 x 16 mm Screws
6 x M6 x 16 mm Screws + Washers
6 x M5 x 16 mm Screws + Washers
6 x M4 x 16 mm Screws + Washers
1 x M5 Allen Key
1 x M4 Allen Key
1 x M3 Allen Key
1 x M2.5 Allen Key
Operator: __________________ __
2
Distributed By:
www.gilkon.com.au Phone: [phone] Email: [e-mail]