GJD CLARIUS VCS-50 User manual

• LED lamps are extremely bright. To avoid possible damage to the eyes,
do not stare into an LED beam.
• In use, avoid touching any external surface of the oodlight, due to the
possibility of high temperatures.
• The oodlight is suitable for connection to 100-240V 50/60Hz.
• If the mains cord lead of this oodlight is damaged, it shall be replaced
by the manufacturer or the service agent or a similar qualied person to
avoid a hazard.
• The oodlight is suitable for use in an ambient temperature of between
-25˚C and +50˚C.
• The oodlight can under no circumstance be mounted on normally
ammable surfaces.
Clarius Mains LED Floodlight
50W, 100W and 200W Floodlight
Quick Installation Guide
VCS-50 - 50W Floodlight
VCS-100 - 100W Floodlight
VCS-200 - 200W Floodlight
SAFETY NOTES
INSTALLATION
Before starting installation, please read these instructions carefully. Failure to
follow them could lead to risk of injury or electrical shock. Please retain them
for your future reference.
This light tting must be installed by a competent person in accordance with
current building and wiring regulations.
As the buyer, installer and/or user of this product it is your own responsibility
to ensure that this tting is t for the purpose for which you have intended it.
GJD cannot accept any liability for loss, damage or premature failure resulting
from inappropriate use.
If in any doubt, consult a qualied electrician.
Switch off the mains before commencing installation and remove the
appropriate circuit fuse or lock off MCB.
This oodlight is suitable for both indoor and outdoor lighting applications, it
has an IP rating of IP65. This means that it is dust tight and will prevent the
ingress of water from water jets.
Do not use in areas where an explosive or chemical atmosphere may exist.
Do not use in areas where ventilation is restricted. Ensure that there is space
around the oodlight to allow adequate circulation of air
The oodlight must be positioned so that there is at least 0.5m (500mm)
between the front of the oodlight and the surface to be illuminated.
It should be placed away from any ammable materials.
Before drilling any xing holes, check that there are no hidden obstructions
behind the mounting surface such as pipes or cables.
The minimum recommended height for installation of the oodlight is 3
metres.
INSTALLATION INSTALLATION - CONTINUED
Check that you have all the tools that you need.
1. Check that the oodlight and its mains lead are not damaged. If there is
any damage, return it to the place where you purchased it. Do not attempt to
repair it yourself.
2. Choose your location to x the oodlight, taking into account the comments
above.
3. Use the oodlight bracket to mark the position of the xing holes.
4. Drill the xing holes and x the oodlight into position using suitable screws
and wall plugs.
5. Check that it is securely xed.
6. Terminate loose ends of wire to an appropriate IP rated junction box or
similar, ensuring the Live, Earth and Neutral polarities are observed.
7. Restore power and test the oodlight.
8. Adjust the angle of the oodlight so that it illuminates the required area. The
oodlight has a beam angle of 60°.Tighten the oodlight using the bolts on the
brackets.
Unit 2, Birch Business Park, Whittle Lane, Heywood, Greater Manchester, OL10 2SX, UK
w: www.gjd.co.uk t: [phone] e: [email protected]
Detect.Illuminate.Dete
r

RoHS: Restriction of Hazardous Substances European directive
EU 2015/863
Certications
WEEE: Waste Electrical & Electronic Equipment European directive
2012/19/EU
CERTIFICATIONS
CLEANING
MAINTENANCE
Clean the oodlight only with a soft dry cloth. Do not use any abrasive or
chemical cleaners. Allow to cool down before cleaning.
The oodlight has a sealed LED lamp and is maintenance free. The LED
lamp cannot be replaced When the LED lamp reaches the end of its life, the
oodlight will have to be replaced.
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF
ELECTRICAL & ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste
Electrical & Electronics Equipment (WEEE). Any WEEE marked products
must not be mixed with general household waste, but kept separate for the
treatment, recovery and recycling of the materials used. Contact your local
authority for details of recycling schemes in your area
SPECIFICATIONS - 50W FLOODLIGHT
SPECIFICATIONS - 200W FLOODLIGHT
50W Floodlight
INPUT VOLTAGE AC100-240V 50 / 60Hz
POWER 50 Watts
POWER FACTOR 0.95
LEDs High quality Osram LEDs
BEAM ANGLE 60°
LUMINOUS FLUX ≈7,500lm, Cool white 6000K
COLOUR RENDERING INDEX Ra = 90
EXPECTED LIFETIME 50000Hr+
PRESSURE VENT Yes
HOUSING
High thermal conductivity
aluminium and Polycarbonate
encapsulated lens module
DIMENSIONS 203 x 292 x 62mm
WATERPROOF RATING IP65
IMPACT RATING IK09
AMBIENT TEMPERATURE -25 °C to +50 °C
WARRANTY 3yrs
100W Floodlight
INPUT VOLTAGE AC100-240V 50 / 60Hz
POWER 100 Watts
POWER FACTOR 0.95
LEDs High quality Osram LEDs
BEAM ANGLE 60°
LUMINOUS FLUX ≈15,000lm, Cool white 6000K
COLOUR RENDERING INDEX Ra = 90
EXPECTED LIFETIME 50000Hr+
PRESSURE VENT Yes
HOUSING
High thermal conductivity
aluminium and Polycarbonate
encapsulated lens module
DIMENSIONS 277 x 292 x 62mm
WATERPROOF RATING IP65
IMPACT RATING IK09
AMBIENT TEMPERATURE -25 °C to +50 °C
WARRANTY 3yrs
200W Floodlight
INPUT VOLTAGE AC100-240V 50 / 60Hz
POWER 200 Watts
POWER FACTOR 0.95
LEDs High quality Osram LEDs
BEAM ANGLE 60°
LUMINOUS FLUX ≈30,000lm, Cool white 6000K
COLOUR RENDERING INDEX Ra = 90
EXPECTED LIFETIME 50000Hr+
PRESSURE VENT Yes
HOUSING
High thermal conductivity
aluminium and Polycarbonate
encapsulated lens module
DIMENSIONS 428 x 292 x 62mm
WATERPROOF RATING IP65
IMPACT RATING IK09
AMBIENT TEMPERATURE -25 °C to +50 °C
WARRANTY 3yrs
SPECIFICATIONS - 100W FLOODLIGHT