Glacier bay HD65601-5101 Assembly instructions

THANK YOU
INSTALLATION AND CARE GUIDE
TWO-HANDLE ROMAN TUB FAUCET
We appreciate the trust and condence you have placed in Glacier Bay through the purchase of this roman tub
faucet. We strive to continually create quality products designed to enhance your home. Visit us online to see
our full line of products available for your home improvement needs. Thank you for choosing Glacier Bay!
Questions, problems, missing parts?
Before returning to the store, call Glacier Bay Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday
9 a.m. - 6 p.m., EST, Saturday
1-855-HD-GLACIER (1-855-434-5224)
HOMEDEPOT.COM
7/2018 REV.01HOMEDEPOT.COM
Model#
HD65601-5101
HD65601-5104
HD65601-5127D
Internet#
306069084
306069105
306069085
SKU#
1003421407
1003421404
1003421406

Phillips
screwdriver Basin
wrench
2
Table of Contents
Important Information..............................2
Warranty ...................................................2
Pre-Installation.........................................2
Planning Installation ..............................2
Package Contents..................................3
Installation................................................4
Care and Cleaning ....................................7
Troubleshooting........................................7
Service Parts ........................................... 8
Important Information
□ Observe all local plumbing and building codes.
□ Cover the sink drain to avoid losing any parts.
□ Review the care and cleaning section included in this guide.
Pre-Installation
PLANNING INSTALLATION
Before beginning the installation of this product, ensure all parts are present. Compare parts with the Package
Contents list. If any part is missing or damaged, do not attempt to install the product. Contact Customer Service
for replacement parts.
TOOLS AND HARDWARE REQUIRED
Adjustable
wrench
Safety
goggles
(2) Supply
lines
Tools and Hardware Required ...............2
Operation...................................................7
Warranty
LIMITED LIFETIME WARRANTY
Glacier Bay products are manufactured with superior quality standards and workmanship and are backed by our
limited lifetime warranty. Glacier Bay products are warranted to the original consumer purchaser to be free of
defects in materials or workmanship. We will replace FREE OF CHARGE any product or parts that proves defective.
Simply, return the product / part to any of The Home Depot retail locations or call 1-855-HD-GLACIER (1-855-434-
5224) to receive the replacement item. Proof of purchase (original sales receipt) from the original consumer
purchaser must be made available for all Glacier Bay warranty claims.
This warranty excludes incidental/inconsequential damages and failures due to misuse, abuse or normal wear and
tear. This warranty excludes all industrial, commercial and business usage, whose purchasers are hereby extended
a ve year limited warranty from the date of purchase, with all other terms of this warranty applying except the
duration of warranty.
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations may not apply to you. This warranty gives you specic legal rights and you may also have other
rights that vary from state to state and province to province. Please see a store or contact 1-855-HD-GLACIER for
more details.
Contact the Customer Service Team at 1-855-434-5224 or visit www.HomeDepot.com.

HOMEDEPOT.COM
Please contact 1-855-HD-GLACIER for further assistance.
3
Pre-Installation (continued)
PACKAGE CONTENTS
Part Description Quantity
HRubber washer 1
IMetal washer 1
J 1
DIndex 1
Mounting nut
K 2Handle
Part Description Quantity
ASpout assembly 1
BSet screw 1
C3.2mm hex wrench 1
GMiddle body 1
ORubber washer 2
PMetal washer 2
Q 2
RHose 2
EProtective cap 1
FConnector 1
Mounting nut
LFlange 2
MHot end valve 1
NCold end valve 1
A
B
C
D
H
I
J
G
F
E
K
L
N
O
P
Q
M
R
S
SProtective cap 2

4
Installation
1 Preparing for installation
CAUTION: Always shut off the water supply before
removing an existing faucet or replacing any part of a
faucet. Open the faucet handle to relieve water pressure
and ensure that the water is completely shut off.
2 Removing the mounting kits
□Remove the protective cap (E). Loosen the
connector (F) from the middle body (G). Adjust
the rubber washer (H), metal washer (I) and
mounting nut (J) to the bottom of middle
body (G).
□Shut off the water supply. Remove the old
faucet.
□Clean the mounting surface.
□Drill holes in the nished deck as shown in
the diagram below.
5 in. min.
8~16 in.
3 in. min.
1-7/8 in. MAX. DECK THICKNESS
1-3/8 in.
Diamter
1-1/8 in.
Diamter
1-3/8 in.
Diamter
NOTE: This kit allows up to 1-7/8 in. deck thickness.
3 Installing the middle body
□From underneath the deck, insert the middle
body (G) with the rubber washer (H), metal
washer (I) and mounting nut (J) through the
mounting hole.
□From above, thread the connector (F) onto
the middle body (G).
□Tighten the mounting nut (J) using a basin
wrench, so that the connector (F) sits ush
against the nished deck surface.
H
I
J
G
E
F
H
I
J
G
F

5
Installation (continued)
5 Removing the mounting kits
□Remove the protective caps (S).
□Loosen the anges (L) from the valve bodys
(M & N). Adjust the rubber washers (O), metal
washers (P) and mounting nuts (Q) to the
bottom of valve bodys (M & N).
HOMEDEPOT.COM
Please contact 1-855-HD-GLACIER for further assistance.
6 Installing the valve bodies
□From underneath the deck, insert the cold end
valve (N) with the rubber washer (O), metal
washer (P) and mounting nut (Q) through
the hole on the right (cold) side.
□From above, thread the ange (L) onto the
valve body (N).
□Tighten the mounting nut (Q) using a basin
wrench, so that the ange (L) sits ush against
the nished deck surface.
□Repeat this procedure for the hot end valve (M)
on the left (hot) side.
NOTE: The hot end valve is identied with a label.
4 Installing the spout assembly
□Install the spout assembly (A) onto the
connector (F). Be sure the spout assembly (A)
is resting rmly on the deck.
□Push down on spout assembly (A) and tighten
set screw (B) with the Hex wrench
(Hex: 3.2mm, C). Insert the index (D).
BC
A
D
F
S
S
L
N
O
P
Q
L
M
O
P
Q
L
N
O
P
Q
M

6
Installation (continued)
9 Making the water supply
connections
□Connect the water supply lines (1) to the
faucet inlets (2). (Supply lines are not
included.)
8 Connecting the hoses
□Connect the hoses (R) to the bottom of the hot
and cold end valves (M & N), as shown.
□Align the middle body (G) in a position that will
allow maximum clearance to connect the
hoses (R).
□Carefully bend the hoses (R) to t in the
available space, and carefully thread the hose
(R) couplings onto the sides of the middle
body (G). Tighten all connections with a wrench.
7 Installing the handle
□Thread the handle (K) onto the ange (L).
□Place the other handle onto the left (hot) valve
and install the same way.
1
2
NOTE: After install handle assembly, if the handle seat is
not aligned with handle in a line as shown in the above
diagram (1), rotate the handle seat back (the ratating angle
can not exceed 90°) to make the handle seat align with
handle in a line.
1
K
L
R
GN
R
M

7
Operation
1Flushing and checking for leaks
□Ensure the faucet handles are in the off position,
and turn on the water supply to check for leaks.
If you discover any leaks, check your connections
to ensure they are installed properly.
□Turn on the hot and cold handles to allow the
water to run for at least one minute. This
ushes away any debris that could cause
damage to internal parts.
□Turn off the water.
Care and Cleaning
□To clean, wipe down with a damp cloth and dry with a towel.
□Do not use abrasive cleaners, steel wool, or harsh chemicals when cleaning this faucet, or the warranty will
be voided.
Troubleshooting
Problem Possible Cause Solution
There are leaks from the
handle.
The bonnet nut has come loose and/or the
washer is dirty or damaged.
□Tighten the bonnet nut.
□Clean or replace the washer.
The water will not shut off
completely.
The cartridge is dirty or broken. □Remove the handle to check
the cartridge.
□Clean or replace.
NOTE: Refer to the service parts section in this manual for
a detailed drawing showing the location of the parts listed
below.
There is a leak from the
spout base when the
faucet is on.
The o-ring which is on the connector
under the spout is worn.
□Remove the spout and replace
a new o-ring.
HOMEDEPOT.COM
Please contact 1-855-HD-GLACIER for further assistance.

8
Service Parts
*Specify Finish
Faucet ID tags can be
found by removing
the hot water handle
16 Metal washer RP64036
Part Description Part Number
Rubber washer RP64035
Part Description Part Number
14
15
O-ring RP60094
12
9
10
13
Mounting nut RP56014
Set screw RP50054
O-ring RP60056
Connector RP70459
Hose RP7004218
17 Mounting nut RP56088
11 Index RP10088*
Many replacement cartridges, aerators, and drain
assemblies can be purchased at your local The
Home Depot store or online at HOMEDEPOT.COM
1RP13651*
3 Flange RP70439
4
5
6
7
Bonnet nut RP70001
8
Cartridge H RP20079
Handle assembly H
2RP13652* Handle assembly C
Rubber washer RP64023
Cartridge C RP20080
Metal washer RP64024
2
3
4
5
6
7
8
11
12
14
15
16
13
18
1
9
10
17

Questions, problems, missing parts?
Before returning to the store, call Glacier Bay Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday
9 a.m. - 6 p.m., EST, Saturday
1-855-HD-GLACIER (1-855-434-5224)
HOMEDEPOT.COM
Retain this manual for future use.

GRACIAS
GUÍA DE USO Y MANTENIMIENTO
GRIFO DE DOS LLAVES PARA BAÑERA ROMANA
Agradecemos la con anza que has depositado en Glacier Bay al comprar este grifo para bañera romana. Nos
esforzamos por crear continuamente productos de calidad diseñados para mejorar tu hogar. Visítanos en Internet
para ver nuestra línea completa de productos disponibles para las necesidades de mejoras de tu hogar.
¡Gracias por elegir a Glacier Bay!
¿Problemas, preguntas o piezas faltantes?
Antes de regresar a la tienda, llama al servicio al cliente de
Glacier Bay de lunes a viernes entre 8 a.m. y 7 p.m. y los
sábados entre 9 a.m. y 6 p.m.(hora estándar del Este)
1-855-HD-GLACIER (1-855-434-5224)
HOMEDEPOT.COM
Internet núm.
306069084
306069105
306069085
Modelo núm.
HD65601-5101
HD65601-5104
HD65601-5127D
SKU núm.
1003421407
1003421404
1003421406