Glacier KODIAK 10 Series User manual

GLACIERCOMPUTER.COM
Kodiak 10
Vehicle Mount
Computer
Quick Reference Guide
Front View
Power
Volume
Power, Storage,
Defrost and
Communication
LED indicators
Programmable Keys
Brightness
Display on/off
(Defrost on/off)
Ambient light sensor
Internal microphone
The LED indicators on the KODIAK 10 show the operating status of your system.
LED Status Description
Power Blink Green Power up
Power Blink Yellow Load BIOS
Power Solid Green System ready to use
Power Blink Red Vehicle battery abnormal
Defrost Solid Green Defrost on
WWAN Solid Green WWAN enabled
WIFI/ BT Solid Green WIFI/ BT enabled
PACKAGE LIST
PRODUCT INTRODUCTION
Before you begin the installation or configuration process, make sure all the components
and accessories are intact. Contact your representative if any is missing or damaged.
Please verify the delivery of the contents upon receipt.
◼KODIAK 10 Vehicle Mount Computer (Model: X10 or P10)
◼Quick Start Guide
◼Touch Screen Protection Film
◼Accessories
◼2 Antennas
◼USB Adapter Cable
◼DC Power Cable
NOTE: The original packing material provides optimal protection to
your device. After unpacking, save the original carton and packing
material in case you need to return the unit for upgrade or service.
TOUCH SCREEN PROTECTION FILM
The film that is attached to the screen in the package is
intended to increase the durability of the touch screen and
protect it from scratching, etching, and damage.
Rear View
Wi-Fi/BT antenna
CONN. (RP-SMA jack)
Wi-Fi/BT antenna
CONN. (RP-SMA jack)
The KODIAK 10 supports a standard VESA
version MIS-D, 75/100, C (75/100mm distance
quadrate order, M5 thread, deepness 9mm)
with four mounting holes on the back side of
the device.
KODIAK X10/P10

Power on through vehicle battery
Wire Color Description
RED V+
BLACK V-
GREEN PE (Safety Ground)
WHITE V+ If Not using
Ignition Sense
PRODUCT INTRODUCTION POWERING ON THE SYSTEM
The KODAIK 10 supports a wide range of DC power inputs (9~60V) via the 4-pin M12 S-
code power cord. You can power the KODIAK 10 through either a vehicle battery or
using a DC/DC converter.
Fuse Requirements
Fuses* are required when connecting
the power cable to a battery. Use a
fuse on the ACC/ignition line to avoid
risk of damage to the cable or the
vehicle.
Make sure that all power supplies
are disconnected when you plug
the power cord into the power
connector.
1. The bare wire lead cable lets you directly wire to 12V, 24V or 48V vehicle power supply.
2. Please refer to the table below for details on connecting your power source.
Bottom View
Side View
Sales: 866.724.6257
[e-mail]
Support: 603.882.1560
[e-mail]
Glacier Computer, LLC
10 Northern Blvd Suite 2
Amherst NH 03031 USA
FURTHER INFORMATION
DC-in
RS232 with PWR (COM1)
DIx2, DOx2
2xUSB2.0/ 2x CAB bus 2.0B
RS-232(TX,RX)/422/485x1,
RS-232(TX,RX)x2, RS-485x2
Optional video input
Gigabit Ethernet
USB Type A
Micro SIM Slot
Micro SD Slot
POWERING ON THE SYSTEM
USB Type-C
DP Alt mode
Notes:
* 4A for 48VDC power input
* 7A for 24VDC power input
* 15A for 12VDC power input
KODIAK X10/P10 GLACIERCOMPUTER.COM
Connect to
V+ If Not
Using
Ignition
Sense