GLITZHOME PRIVACY SCREEN User manual

ASSEMBLY INSTRUCTION
PRIVACY SCREEN
Please carefully unpack and identify each component before beginning assembly.
Before you begin, please refer to parts list to make sure that you have all parts. Please
take care when assembling the unit and always place the parts on a clean, soft surface.
If you require assistance with assembly or parts, please call 888-357-7263.
Get social with us and discover more about our products, tips and exclusive discounts!

Assembly Instruction 1
PRE-ASSEMBLY INSTRUCTIONS:
WARNING! DO NOT LET CHILDREN PLAY IN OR AROUND THE UNIT DUE TO THE POSSIBLE RISK OF FINGER
ENTRAPMENT.
• Please read through this instruction before beginning assembly.
• Two adults for assembly are recommended.
• Wearing gloves (not included) during assembly is recommended.
• Don’t assemble the privacy screen on a Hard Surface.
• If the privacy screen will be used in a strong wind area, we highly recommend using four
Hex-Head Sleeve Anchors to securely fasten the privacy screen to solid ground.
• Do not fully tighten the bolts until all of them have been inserted and hand tightened.
• Panel may fit tightly and may require a rubber mallet (not included) to nudge the panel into
place.
• Check for any loose screws and tighten them before use.
Screen Panel (A)
Qty: 3
PARTS AND COMPONENTS
Stand Foot (B)
Qty: 2
Bottom Long Stand
Riser Bar (C)
Qty: 2
Top Short Stand
Riser Bar (D)
Qty: 2
Bolts (E)
Qty: 16
Allen Key (F)
Qty: 1
Ground Stakes(G)
Qty: 4

PLEASE CAREFULLY UNPACK AND IDENTIFY EACH COMPONENT BEFORE BEGINNING ASSEMBLY. BEFORE DISCARDING THE
PACKAGING, PLEASE DOUBLE-CHECK THE CONTENTS TO ENSURE YOU HAVEN'T ACCIDENTALLY DISCARDED ANY PARTS
NECESSARY FOR ASSEMBLE.
ASSEMBLY INSTRUCTION
Assembly Instruction
2
STEP 1 Attach Bottom Long Stand Riser Bar (C) to Stand Foot (B) using Bolts (E). Use 2
bolts for each side.Make sure to tighten securely with the Allen Key (F).
STEP 2
Slide the first Screen Panel (A) into the channel of the two assembled Bottom
Long Stand Riser Bars (C), secure it using 2 Bolts (E) from each side with the
Allen Key (F).
Notes:
• Make sure the holes aligned and the
panel is placed correctly.
• Panel may fit tightly and may require
a rubber mallet (not included) to nudge
the panel into place.
• Do not fully tighten the bolts until all
of them have been inserted and hand
tightened.
B
B
C
C
CA
E
E
E
E
E
EF
E
E
E
F
F

Assembly Instruction 3
STEP 3
Slide the second Screen Panel (A) into the channel of the two assembled Bottom
Long Stand Riser Bars (C), positioning it above the first screen panel. Secure it
using 1 Bolt (E) from each side with the Allen Key (F). You now have the assembled
part 1.
STEP 4 Attach the Top Short Support Bars (D) to the last Screen Panel (A). Secure it using
2 Bolts (E) from each side. Make sure the holes aligned and the panel is placed
correctly. Hand tighten only. You now have the assembled part 2.
Notes:
• Make sure the holes aligned and the
panel is placed correctly.
• Panel may fit tightly and may require
a rubber mallet (not included) to nudge
the panel into place.
• Do not fully tighten the bolts until all
of them have been inserted and hand
tightened.
C
D
D
C
A
E
E
E
E
E
E
E
EF
F

Assembly Instruction
4
STEP 5 Attach the assembled part 2 onto the assembled part 1. Secure the two assembled
parts using the remaining 2 Bolts (E) with the Allen Key (F).
STEP 6 Your Privacy Screen is now fully assembled and ready for use. Enjoy the added
privacy and functionality it provides!
Notes:
• Make sure the holes aligned and the
panel is placed correctly.
• Panel may fit tightly and may require
a rubber mallet (not included) to nudge
the panel into place.
• Do not fully tighten the bolts until all
of them have been inserted and hand
tightened.
E
EE
F
Note:
• Use the Ground Stakes (G) (included)
to secure the privacy screen to the
ground for stability if necessary.
G
G
G
G



