Globalmediapro HBT-332H100 User manual

ALL to HDMI with HDBaset 100m
Cat6 Extender
Operation Manual

1.Introdu tion
This machine is a high−performance presentation scaler and
switcher. It accepts one of eight inputs: one DVI, two VGA, one
composite video and four HD I signals. The HD I1, HD I2 to
bypass the input function, supports input resolutions up to
4Kx2K@30Hz, and HD I3, HD I4, DVI,
VGA1, VGA2, CV scales the video, supports output resolutions up
to 1920x1080P@60Hz. It scales the video, embeds the audio, and
simultaneously outputs the signal to HD I and HDBaseT output,
HDBaseT output transmission distances up to 328ft/100m (100m
Version) through CAT6/7 cable, together with S/PDIF and stereo
audio outputs. Flexible control mode diversity, through the front
panel button, remote control, RS-232 and TCP/TP control.
2.Features
HD I, HDCP and DVI compliant
The HD I1,HD I2 to bypass the input function, supports
input resolutions up to 4Kx2K@30Hz
The HD I3,HD I4,DVI,VGA1,VGA2,CV scales the video,
supports input resolutions :
HD I: 480i to 1080p
VGA:1920x 1080P@60Hz, 1360 x 768P@60Hz, 1280 x
1024P@60Hz,
1024 x 768P@60Hz,1280 x 720P@60Hz,1280 x
768P@60Hz,
800 x 600@60Hz, 640 x 480P@60Hz, 720 x 400P@85Hz
CV: Supports PAL, NTSC3.58, NTSC4.43, SECA , PAL/ ,
PAL/N standard TV formats
Supports transmission distances up to 328ft/100m (100m
Version) through CAT6/7 cable
Ver1.1 Page 2 of 21

Supports POE function
VGA video supports YPbPr and RGBHV
Picture Adjustment Settings
Supports embeds the audio
Supports S/PDIF and stereo audio outputs
Supports HDBaseT LAN Serving function
The USB and RS-232 for the firmware update
Supports RS-232, remote control, on-panel control and
TCP/IP Control
Supports smart EDID management
3.Pa kage Contents
ALL to HD I with HDBaset 100m Cat6 Extender 1pcs
HDBaseT Receiver 1pcs
12V/2.5A DC power adaptor 1pcs
Operation anual 1pcs
Wideband IR Tx cable 9pcs
Wideband IR Rx cable 2pcs
Scaler Switcher IR Remote 1pcs
ounting ears 2pcs
RS232 cable 1pcs
4.Spe ifi ations
Input Ports 4×HD I,1×DVI,2xVGA,1xRCA ,
1×RS-232,1xRJ-45(Control),1x IR
IN, 7x3P captive screw
connector(3.81mm),
1xUSB
Output Ports 1×HD I,2xRJ-45(LAN), 2xRCA,
1xRJ-45(HDBaseT),8x IR OUT
Input Resolutions Support Up to 4Kx2K@30Hz
Output Resolutions Support U p t o 4 Kx2K@30Hz(HD I
Ver1.1 Page 3 of 21

BYPASS)
Up to 1920x1080P@60Hz(SCALES)
Control IR , RS-232 , TCP/TP , Buttons
ESD Protection Human-body odel:
± 8kV (Air-gap discharge)
± 4kV (Contact discharge)
Power Supply 12 V/2.5 A DC (US/EU standards,
CE/FCC/UL certified)
Dimensions 440 mm (W)×200 mm (D)×45 mm (H)
Weight 2300g
Chassis aterial etal
Silkscreen Color Black
Operating Temperature 0 ºC~40 ºC/32 ºF~104 ºF
Storage Temperature −20 ºC~60 ºC/−4 ºF~140 ºF
Relative Humidity 20~90 % RH (non-condensing)
Power Consumption 14.5 W( ax)/1.8W(Standby)
5. PANEL FUNCTIONS
5.1 Front Panel
Part 1. IR: IR Receiver window (accepts the remote control
signal of this device only).
POWER: Press this button to power the device standby
Ver1.1 Page 4 of 21

on/off. Press this button more than 2 seconds,
the device has reached the standby mode. The
LED will illuminate green when the power is on,
red when it is in 'Standby' mode.
LOCK: Press this button to lock all the buttons on the panel,
press again to unlock.
AUDIO SELECT: Press this button to select audio from
digital(INT) or analog(EXT),When the signal is
HD I input.
Note: DVI interface as HD I input has the
same function.
Part 2. HDMI INPUT BYPASS: Press these buttons to switch
directly to the required source. An LED will
illuminate to indicate the selected input source.
Part 3. SCALER SELECT:
1. Source select: Press these buttons to switch
directly to the required source. An LED will
illuminate to indicate the selected input
source.
2. Picture adjustment: Press scaler or auto
adjust button to adjust the output picture.
Note: a. The output signal source must be
VGA input source.
b. Scaler adjust the step: six steps
3. Resolution select: Press the button to select
different resolution output. An LED will
illuminate to indicate the selected resolution.
5.2 Rear Panel
Ver1.1 Page 5 of 21

Part1: OUTPUT
The HD I OUTPUT connect to HD I equipped TVs or
monitors and the HDBT OUTPUT connect to the HDBT
Receiver. The coaxial and stereo output is connected an audio
amplifier. The LAN is connected to PC or Router.
Part2: INPUT
1) HDMI 1/ 2/ 3/ 4: Connect to HD I sources such as DVD
player /Blu-ray player for both video and audio signal
conversion.
2) DVI: Connect to DVI sources such as PC.
3) VGA 1/ 2: Connect to a PC/Laptop source for video signal
input with a D-Sub 15pin cable or connect to a DVD player
source for video signal input with a D-Sub 15pin to 3 RCA
adaptor cable.
4) CV+L/R: Connect to a composite video source such as a
video /DVD player for both video and audio signal
conversion.
5) 3P aptive s rew onne tors(3.81mm):Connect to
source’s L/R output with 3P cable for audio signal
conversion.
Part 3: IR OUT
Connect with the supplied wideband IR TX.
Part 4: CONTROL
1) TCP/IP: This port is the link for TCP/IP controls, connect to
an active Ethernet link with an RJ45 terminated cable.
Ver1.1 Page 6 of 21

2) RS232(DB9): Connect to a PC or control system with D-
Sub 9-pin cable for the transmission of RS-232
commands.
Note: The RS-232 interface can control the machine.
3) IR IN: Connect with the supplied wideband IR RX
4) RS232(3.81mm 3P aptive s rew onne tor):Connect to
a PC or control system with a D-Sub 9pin to 3P cable.
Note: The RS-232 interface only with the remote receiver
(HDBaseT Receiver) RS-232 communication.
Part5: UPDATE PORT
Connect U flash drive, system software update.
Part6: DC POWER INPUT
Plug the 12V/2.5A DC power supply into the DC12V power in.
6. Remote Control
1. Press this button to power on the
switcher or set it to standby mode.
2. Input Selection: Press these
buttons to switch to the required
source.
3. Audio select: Click these buttons
to select audio from digital (INT) or
analog (EXT), when the signal is
switch to the HD I or DVI signal
source.
4. Press scaler or auto adjust button
to adjust the output
picture.
Note: a .
The output signal
source must be
Ver1.1 Page 7 of 21

VGA input source.
b. Scaler adjust the step: six steps.
5. Resolution select: Press these buttons to select different
resolution output.
6. These buttons for function extension keys.
7. Serial Control
The RS-232 port lets you send and receive simple RS-232 signals
between a controller and a serial device via the switcher which is
connected to the RS-232 port (3.81mm 3P captive screw
connector) and outputs via CAT5e/6/7 cable.
The example, illustrated in Figure 2, shows a PC or control
system that is connected to the switcher via the RS-232 port
(3.81mm 3P captive screw connector). The HDBT output
connector on the switcher is connected via CAT5e/6/7 cable to an
HDBT receiver. This HDBT receiver connects to a projector via
HD I and RS-232.
The PC or control system sends RS-232 signals control projector,
by the switcher and HDBT receiver.
Figure 2
Ver1.1 Page 8 of 21

8. IR Control Operations
The IR control can realize two-way control function, and the 8 IR
OUT ports are corresponding to the 8video inputs one to one, and
switch following the corresponding video source.
The example, illustrated in Figure 3 and Figure 4 :
1) To control far-end display: The IR Receiver (Rx1) is connected
to the switcher IR IN port. The HDBT output connector on the
switcher is connected via CAT5e/6/7 cable to an HDBT
receiver. The HDBT receiver connect to a TV via HD I, and
the IR Transmitter (Tx2) is connected to the HDBT receiver IR
OUT port.
To control this machine(switcher) or far-end display device
from local by using corresponding remote controller.
Figure 3
2) Control local device (DVD, Switcher, etc) from remote: The IR
Receiver (Rx2) is connected to the HDBT receiver IR IN port.
The HDBT output connector on the switcher is connected via
CAT5e/6/7 cable to an HDBT receiver. The IR Transmitter
(Tx1) is connected to the switcher IR OUT port.
Ver1.1 Page 9 of 21

IR remote can be used to control this machine (switcher) or
local source device from remote.
Figure 4
IR Cable Pin Assignment, illustrated in Figure 5:
Ver1.1 Page 10 of 21