GLP YpocBasic 250 User manual

Instruction Manual
from software version 1.0
(instruction version 1.05)
e-mail: [e-mail]
Internet: http://www.GLP.de

GLP German Light Production (V1.05) 2
This side is intentionally unlabelled.

GLP German Light Production (V1.05) 3
Table of contents
1Description of Device ............................................................................................. 5
1.1 Safety Instructions............................................................................................ 6
2Preparation and Installation .................................................................................. 7
2.1 Mounting .......................................................................................................... 7
2.1.1 Clamps .................................................................................................. 7
2.1.2 Mounting plate ....................................................................................... 7
2.2 Secure the Y YP PO OC C 2 25 50 0 B Ba as si ic c ............................................................................ 8
2.3 Connections ..................................................................................................... 9
2.3.1 Power supply ......................................................................................... 9
2.3.2 DMX....................................................................................................... 9
2.4 Fuse ................................................................................................................. 9
3The Menu Field...................................................................................................... 10
3.1 Adjust the DMX- Address (D001)..................................................................... 11
3.2 The Test Program (TEST) ................................................................................ 11
3.3 The Audio Program (AUDI).............................................................................. 11
3.4 Lamp On/Off (LAMP) ........................................................................................ 12
3.5 Reset (RESE) ................................................................................................... 12
3.6 Running time of lamp and unit (TIME) ............................................................. 12
3.7 Invert Pan Movement (RPAN)........................................................................... 12
3.8 Invert Tilt Movement (RTLT) ............................................................................ 12
3.9 Special Functions (SPEC)................................................................................. 13
3.9.1 Manual Drive (MANU) ............................................................................. 13
3.9.2 Lamp On automatically (LAAU).............................................................. 13
3.9.3 Lamp Off via DMX (DLOF) ..................................................................... 14
3.9.4 DMX Input (DMXI) ................................................................................. 14
3.9.5 Display (DISP) ...................................................................................... 14
3.9.6 Fixture Temperature (TEMP).................................................................. 15
3.9.7 Fan Control (FANS)................................................................................ 15
3.9.8 Adjustments and Calibrations (ADJU).................................................... 15
3.9.9 Default Settings (DFSE) ......................................................................... 16
3.9.10 Feedback (FEED)................................................................................... 16
3.9.11 Correction of faults (EFLG) .................................................................... 17
3.10 Error and Information Messages .................................................................... 17
4DMX Channel Selection (DMX Protocol)............................................................. 17

GLP German Light Production (V1.05) 4
5Change the Lamp.................................................................................................. 20
5.1 Safety Regulations ......................................................................................... 20
5.2 Realize the Lamp Change.............................................................................. 21
5.3 Lamp adjustment............................................................................................ 21
6Change a Gobo ..................................................................................................... 22
6.1 Safety Regulations ......................................................................................... 22
6.2 Realize the Gobo Change .............................................................................. 22
7Maintenance and Cleaning the Y YP PO OC C 2 25 50 0 B Ba as si ic c................................................ 23
7.1 Safety Regulations ......................................................................................... 23
7.2 Circumference and Interval (rule-of-thumb).................................................... 23
7.3 Cleaning the Optical System .......................................................................... 24
8Technical Specification........................................................................................ 25
9Index ...................................................................................................................... 27

GLP German Light Production (V1.05) 5
1 Description of Device
1
2
3
4
1 Moving Head
2 Arm
3 Base
4 Focus Adjustment
5 Up- button
6 Down- button
7 Enter- button
8 Mode- button
9 LED- Display
10 Software-Update
connector
11 Microphone- Intensity
12 DMX- Input
13 DMX- Output
14 Power On/Off
15 Fuse F3,15 A
16 Fan (air inlet)
MaxMin
DMX IN DMX OUT
So ft w ar e U pd at e
1.Gr ound
2.Data -
3.Data +
POWER
210V ~
230V ~
250V ~
50Hz
60Hz
Powe r i nput
FUSE:
T3.15A@250V
LAMP:
MSD 250W
Serial
number:
Fuse
Mi c S e n sit i ve
12
3
PUSH
FUSE
MODE ENTER UPDOWN
MO
DE
E
NTER
UPDO
W
N
87 65
9
10
11
12 13 14
15
16

GLP German Light Production (V1.05) 6
1.1 Safety Instructions
The Y YP PO OC C 2 25 50 0 B Ba as si ic c is a High-Tech Product. To guarantee a
smooth operation, it is necessary to keep following rules.
The manufacturer of this device will not take responsibility of
damages through disregard of the information in this manual.
Warranty adjustments will be canceled.
1. Make sure before putting into operation, that the fan and the air inlets are
clean and not blocked by anything.
2. Attention: Don’t touch the device during the operation. This can cause injuries
or damages.
3. Unplug the
Y
YP PO OC C 2 25 50 0 B Ba as si ic c from the AC outlet before any service.
4. It is necessary to wait at least 30 minutes after disconnecting the AC before
you open the Y YP PO OC C 2 25 50 0 B Ba as si ic c. Please do not touch the bulb of the lamp if
you are not absolutely sure it is cold. -Danger of BURNING-
5. Never look directly into the beam of the lamp. You risk injury of your retina and
blindness.
6. Pay attention of the maximum lamp operation time. You have to change it if
the lamp shows any deformations or damages. The same is with all glass
components, color filters, lenses and mirrors.
7. To allow a secure operation, follow also the Installation guide described in
chapter 2. Operating the Y YP PO OC C 2 25 50 0 B Ba as si ic c without suited safety aids like
Safety cables or clamps/hooks can increase the risk of an accident.
8. The installation should be done by qualified staff only. You need to pay
attention to the common rules of technology that are not explicit mentioned in
this manual.
9. Use only original spare parts. Any structural modification will cancel all
warranty adjustments.
LASERSTRAHLUNG
NICHT IN DEN STRAHL BLICKEN
LASER KLASSE 3R
NACH DIN-EN 60825-1/11:2001
P 5mW; = 635-650 nm
0
λ
Attention: Laser of class 3R may
injure your retina after a short resi-
dence time even without any optical
instrument. Avoid any direct ex-
posure of your eyes!

GLP German Light Production (V1.05) 7
2 Preparation and Installation
2.1 Mounting
The Y YP PO OC C 2 25 50 0 B Ba as si ic c is fully operational whether it hangs or is mounted to the
wall. It can also be operated while standing on the floor. Keep a safety distance of
0.5 m towards any easy inflammable materials (decoration etc.). Install a safety
wire that can hold at least 10 times the weight of the fixture. Never use the
carrying handles for secondary attachment.
Pay attention to the regulations of: BGV C1 (former VBG 70)
and DIN VDE 0711-217. Regulations of show laser BGV B2
(11.2001), E DIN 56912 part 6, DIN-EN 60825 part 1+2.
The installation should be done by qualified staff only.
2.1.1 Clamps
Use two clamps on the backside of the Y YP PO OC C 2 25 50 0 B Ba as si ic cto mount the unit
on a truss (each two opposite threads max. M10x20). See also printing on
the backside of the case.
2.1.2 Mounting plate
For a permanent installation of the Y YP PO OC C 2 25 50 0 B Ba as si ic cyou can use a
optional mounting plate to fix the unit on a wall. The plate uses 4x screws
M6x20.

GLP German Light Production (V1.05) 8
2.2 Secure the
Y
YP PO OC C 2 25 50 0 B Ba as si ic c
Regardless of the rigging of the Y YP PO OC C 2 25 50 0 B Ba as si ic c you have to use a stipulated
safety wire. Therefore you have to thread to safety wire through to two provided
holes on the backside of the fixture and connect it with the truss-support. Pay
attention to a safe and proper fastening.

GLP German Light Production (V1.05) 9
2.3 Connections
2.3.1 Power supply
230 Volt, 50 Hz,
Connected load 500W <=> 2,2 A (blind current compensation).
or 115V, 60 Hz
Connected load 500W <=> 4,4 A (blind current compensation).
Please see printing on the case for the right Power supply !
2.3.2 DMX
DMX 512 Standard input/output. See also printing on the case for the right
pin assignment.
[+] = Pin 3 / [-] = Pin 2 / [Ground] = Pin 1
The DMX- Addressing starts at the DMX- Address [001].
2.4 Fuse
The Y YP PO OC C 2 25 50 0 B Ba as si ic c electronic system is protected by a 5x20 mm fuse.
230V / T 3,15A (EU model) or 115V / T 6,3A (US model)
Please see the printing on the Y YP PO OC C 2 25 50 0 B Ba as si ic c for more details.
Attention:
• Disconnect AC outlet before changing a fuse!
• Use only the original declared fuse type!

GLP German Light Production (V1.05) 10
3 The Menu Field
You find the control board on the side part of the base. It allows
you to make all necessary adjustments of the Y YP PO OC C 2 25 50 0 B Ba as si ic c. .
With the Mode-key you get into the main menu. Afterwards you
can navigate through the menu with the Up/Down-keys. Push the
Enter-key to get in the next menu level or to confirm your settings.
Make them and set functions ON/OFF with the Up/Down-keys. Con-
firm and save it with the Enter-key (the display shows OK). Push
the Mode-key to cancel the entry and go back to the main menu.
MODE ENTER UPDOWN
MODEENTERUPDOWN
LED-Displa
y
Mode-ke
y
Enter-ke
y
Down-ke
y
Up-ke
y
Level 1 Level 2 Level 3 Remark
D001
Define the DMX start address
TEST
Test program of all functions
AUDI ASLW Self-running audio program (slow)
AFST Self-running audio program (fast)
MSTR Master for the audio program
SVPT Basic position for the audio program
SIZE Size for the audio program (NORM-BIG-MIDL-SMAL)
LAMP
Switch on/of the lamp direct at the YPOC 250 Basic
RESE
Reset
TIME POWR Running time of the fixture (no destructible)
LA1 Running time of the lamp (erasable)
LA2 Running time of the lamp (no destructible)
RPAN
Reverse Pan-direction
RTLT
Reverse Tilt-direction
SPEC MANU Manual drive of all device functions
LAAU
Automatic lamp start
DLOF
Switch off lamp via DMX
DMXI
Reed out actual DMX-values
DISP D ON Display On/Off
REV Twist the display
TEMP
Reed out internal temperature
FANS HIGH Maximum cooling fan velocity
REG Automatic cooling fan control
LOOF Low cooling fan speed Ælamp off
LOHI Low cooling fan speed Æautomatic
ADJU CODE xxxx Use the code for entering the calibration menu (for
authorized person only)
COLO Calibration of the color wheel
GOBO Calibration of the gobo wheel
SHT1 Calibration of the shutter 1
SHT2 Calibration of the shutter 2
clre Settings in the internal memory (superuser only)
facc Must read on. Protected with a code.
DFSE
Call on the default function values
FEED
Pan/Tilt feedback (error correction) On/Off
ÅDOWN - UP Æ
EFLG
Correction of faults