Chauvet Rogue r2 Beam User manual

Quick Reference Guide
English EN
Español ES
Français FR
Nederlands NL

Rogue™ R2 Beam QRG EN
2
About This Guide
The Rogue™ R2 Beam Quick Reference Guide (QRG) has basic product
information such as connection, mounting, menu options, and DMX values.
Download the User Manual from www.chauvetprofessional.com for more details.
Disclaimer
The information and specifications contained in this QRG are subject to change
without notice.
Safety Notes
• DO NOT open this product. It contains no user-serviceable parts.
• DO NOT look at the light source when the product is on.
• To eliminate unnecessary wear and improve its lifespan, during periods of
non-use completely disconnect the product from power via breaker or by
unplugging it.
• CAUTION: When transferring product from extreme temperature
environments, (e.g. cold truck to warm humid ballroom) condensation may
form on the internal electronics of the product. To avoid causing a failure,
allow product to fully acclimate to the surrounding environment before
connecting it to power.
• CAUTION: This product’s housing may be hot when lights are operating.
• Mount this product in a location with adequate ventilation, at least
20 in (50 cm) from adjacent surfaces.
• DO NOT leave any flammable material within 50 cm of this product while
operating or connected to power.
• USE a safety cable when mounting this product overhead.
• DO NOT operate this product outdoors or in any location where dust,
excessive heat, water, or humidity may affect it. (IP20)
• DO NOT operate this product if the housing, lenses, or cables appear
damaged.
• DO NOT connect this product to a dimmer or rheostat.
• ONLY connect this product to a grounded and protected circuit.
• ONLY use the mounting brackets or the handles to carry this product. Do not
carry by the moving head.
• In the event of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 113 °F (45 °C). Do not operate this
product at higher temperatures.
Contact
Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux, contact your
distributor to request support or return a product. From inside
the U.S., UK,
Ireland, Mexico, or Benelux, use the information in Contact Us
at the end of this
QRG.
What Is
Included
• Rogue™ R2 Beam
• Neutrik® powerCON® power cord
•
2 Omega brackets with mounting hardware
• Warranty Card
• Quick Reference Guide
AC Power
This product has an auto-ranging power supply that can work with an input voltage
range of 100–240 VAC, 50/60 Hz.
To eliminate unnecessary wear and improve its lifespan, during periods of
non-use completely disconnect the
product from power via breaker or by
unplugging it.
AC Plug
Connection
Wire (U.S.)
Wire (Europe)
Screw Color
AC Live
Black
Brown
Yellow/Brass
AC Neutral
White
Blue
Silver
AC Ground
Green/Yellow
Green/Yellow
Green

Rogue™ R2 Beam QRG EN
3
Replacing The
Fuse
1. Disconnect this product from power.
2. Using a flat-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove blown fuse and replace with a good fuse of the same type and rating.
4. Screw the fuse holder cap back in place and reconnect power.
Lamp
Replacement
1. Turn the fixture off and disconnect it from power.
2. Wait at least 15 minutes for the lamp to cool down.
3. Remove both head covers by removing 8 Phillips-head ¼-turn screws.
4. Orient the rear of the product so that the fan is facing upward.
5. Remove the 2 Phillips-head screws on the sides of the fan assembly.
6. Roll the fan assembly to the right to expose the lamp.
7.
Using the lamp base, push the lamp down against the spring clips located on the
bottom, then roll the lamp out the top.
8. Remove the 2 wires connected to the lamp by the spade terminals.
9. Reverse the steps above to install the new lamp.
Please refer to the User Manual for more detailed instructions with images.
¼-turn
Phillips-head
screws

Rogue™ R2 Beam QRG EN
4
DMX Linking
The Rogue™ R2 Beam will work with a DMX controller using a 3- or 5-pin DMX
data connection. A DMX Primer is available from www.chauvetprofessional.com
DMX Connection
The Rogue™ R2 Beam uses a 3- or 5-pin DMX data connection for its DMX
personalities: 15CH and 18CH.
See the User Manual for information about
connecting and configuring the product for DMX operation.
Mounting
Before mounting this product, read the Safety Notes. Use at least two mounting
points
per product. Make sure the mounting clamps are capable of supporting the
weight of the product. For our CHAUVET® line of mounting clamps, g
o to
trusst.com/productcategory/base-plates-accessories-clamps/.
Product
Mounting
Diagram
Control Panel
Description
Button
Function
<MENU>
Exits from the current menu or function
<ENTER>
Enables the currently displayed menu or sets the currently
selected value into the selected function
<UP>
Navigates upwards through the menu list or increases the
numeric value when in a function
<DOWN>
Navigates downwards through the menu list or decreases the
numeric value when in a function
Overhead Mounting
Floor Mounting
Mounting
Clamp
Safety Cable
Omega Bracket

Rogue™ R2 Beam QRG EN
5
Menu Map
Main Level
Programming Levels
Description
Address
001–512
Sets the DMX starting address
Run Mode
DMX
15CH
Selects the DMX mode
18CH
Auto Test
Runs the product’s test sequence
Manual Test
Pan
000–255 Allows manual control of all settings from
the control panel
Pan Fine
Tilt
Tilt Fine
P/T Speed
Dimmer
Dimmer
Fine
Shutter
Color
Gobo
Prism
R–Prism
Zoom
Focus
Frost
P/T Macro
P/T
Ma.Speed
Special
Function

Rogue™ R2 Beam QRG EN
6
Menu Map (Cont.)
Main Level
Programming Levels
Description
Setup
Pan Reverse
YES
Reverse pan operation
NO
Normal pan operation
Tilt Reverse
YES
Reverse tilt operation
NO
Normal tilt operation
Screen Reverse
YES
Rotates control screen view 180°
NO
Normal control screen view
Pan Angle
540
Selects the 540° pan angle range
360
Selects the 360° pan angle range
180
Selects the 180° pan angle range
Tilt Angle
270
Selects the 270° tilt angle range
180
Selects the 180° tilt angle range
90
Selects the 90° tilt angle range
BL.O.P/T Move
YES
Defines the pan/tilt move-in-black delay
NO
BL.O.ColorMove
YES
Defines the color change move-in-black
delay
NO
BL.O.GoboMove
YES
Defines the gobo change move-in-black
delay
NO
Lamp Settings
On/Off
ON
Turns lamp on/off
OFF
State/Power
on
ON
Defines the status of lamp when powering
up product
OFF
Off Via Dmx
YES
Turns off the unit via DMX controller
NO
On If Dmx
On
YES
Turns lamp on when DMX signal is
detected
NO
Off If Dmx
Off
YES
Turns lamp off when DMX signal is lost
NO
Ignition
Delay
000–255
Selects duration of delay between product
power on and lamp power on
Low Power
Delay 000–255
Selects the duration of delay when shutter
is closed and lamp enters lower power
state
Reset Lamp
Time
YES
Resets lamp timer to 0
NO
Leaves lamp time unchanged

Rogue™ R2 Beam QRG EN
7
Menu Map (Cont.)
Main Level
Programming Levels
Description
Setup
(Cont.)
Maintenance
Timer
Interval 10–250
Defines amount of hours between
maintenance
Remaining
Time
NO
Shows amount of time remaining in
maintenance cycle
RESET
Resets the time back to the beginning
Reset Function
Pan/Tilt
YES
Resets pan/tilt functions to the home
position
NO
Shutter/
Prism
YES
Resets all shutter/prism functions to the
home position
NO
Color
YES
Resets all color functions to the home
position
NO
Gobo
YES
Resets all gobo functions to the home
position
NO
Zoom/Frost
/Focus
YES
Resets the zoom, frost, and focus
functions to the home position
NO
All
YES
Resets all functions to the home position
NO
Factory Settings
YES
Reverts the product back to the original
factory settings
NO
Sys Info
Ver:
Displays the software version
Running Mode:
Displays the current running mode
Dmx Address:
Displays the current DMX address
Temperature:
Displays the product’s temperature in
Celsius
Lamp On Time:
Displays the amount of time the lamp has
been on (provided the counter has been
reset upon installation of new lamp)
Remain Time:
Shows amount of time remaining in
maintenance cycle

Rogue™ R2 Beam QRG EN
8
DMX Values
18CH
Channel
Function
Value
Percent/Setting
1
Pan
000ó255
0–100%
2
Fine Pan
000ó255
0–100%
3
Tilt
000ó255
0–100%
4
Fine Tilt
000ó255
0–100%
5
Pan/Tilt Speed
000ó255
0–100%
6
Dimmer
000ó255
0–100%
7
Fine Dimmer
000ó255
0–100%
8 Shutter
000ó007
008ó015
016ó131
132ó167
168ó203
204ó239
240ó247
248
ó
255
Closed
Open
Slow to fast
Fast close, slow open from slow to fast
Slow close, fast open from slow to fast
Pulse effect from slow to fast
Random effect from slow to fast
Open
9 Color Wheel
000ó004
005ó008
009ó012
013ó016
017ó020
021ó024
025ó028
029ó032
033ó036
037ó040
041ó044
045ó048
049ó052
053ó056
057ó060
061ó127
128ó189
190ó193
194ó255
Open
Red
Deep yellow
Turquoise
Green
Light green
Light purple
Pink
Light yellow
Magenta
Blue
CTO 3200 K
CTO 5600 K
CTO 6500 K
UV
Split colors
Clockwise color scroll, fast to slow
Stop
Counter-clockwise color scroll, slow to fast

Rogue™ R2 Beam QRG EN
9
DMX Values (Cont.)
18CH
(Cont.)
Channel
Function
Value
Percent/Setting
10 Gobo Wheel
000ó003
004ó006
007ó009
010ó012
013ó015
016ó018
019ó021
022ó024
025ó027
028ó030
031ó033
034ó036
037ó039
040ó042
043ó045
046ó048
049ó051
052ó055
056ó059
060ó127
128ó189
190ó193
194ó255
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 8
Gobo 9
Gobo 10
Gobo 11
Gobo 12
Gobo 13
Gobo 14
Gobo 15
Gobo 16
Gobo 17
Open
Gobo shake 1–17, slow to fast
Clockwise gobo scroll, fast to slow
Stop
Counter-clockwise gobo scroll, slow to fast
11 Prism
000ó004
005ó255
No function
Prism insert
12 Prism Rotate
000ó127
128ó189
190ó193
194ó255
Prism index
Counter-clockwise rotation, fast to slow
Stop
Clockwise rotation, slow to fast
13
Prism Zoom
000ó255
0–100%
14
Focus
000ó255
0–100%
15
Frost
000ó255
0–100%

Rogue™ R2 Beam QRG EN
10
DMX Values (Cont.)
18CH
(Cont.)
Channel
Function
Value
Percent/Setting
16 Movement Macros
000ó007
008ó015
016ó023
024ó031
032ó039
040ó047
048ó055
056ó063
064ó071
072ó079
080ó087
088ó095
096ó103
104ó111
112ó119
120ó127
128ó135
136ó143
144ó151
152ó159
160ó167
168ó175
176ó183
184ó191
192ó199
200ó207
208ó215
216ó223
224ó231
232ó239
240ó247
248ó255
No function
Effect 1
Effect 2
Effect 3
Effect 4
Effect 5
Effect 6
Effect 7
Effect 8
Effect 9
Effect 10
Effect 11
Effect 12
Effect 13
Effect 14
Effect 15
Effect 16
Effect 17
Effect 18
Effect 19
Effect 20
Effect 21
Effect 22
Effect 23
Effect 24
Effect 25
Effect 26
Effect 27
Effect 28
Effect 29
Effect 30
Effect 31