GMP CUB 3 X 3 BLK User manual

GOLBAL PROCUREMENT AND MARKETING LIMITED
Assembly instruction- Please keep for future reference CUB 3 X 3 BLK
Dimensions No.People Assembly Time OW#
Width: 90 cm
Depth: 30 cm
Height: 90 cm
60 mins
(approx)
If you need help or have damaged or missing parts, please email [e-mail]
thank you
For purchasing this
GPM Limited
product
1
9 CUBE STORAGE CUBE WITH BACK
CUB 3 X 3 GRY
CUB 3 X 3 OAK
CUB 3 X 3 WHT
CUB 3X3 BLK / CUB 3X3 OAK
CUB 3X3 GRY / CUB 3X3 WHT
900mm
300mm
900mm
(279mm)
Important
PLEASE READ THESE INSTRUCTION FULLY BEFORE STARTING ASSEMBLY.
PLEASE DO NOT THROW THE PACKAGING AWAY UNTIL YOU ARE STATISFIED WITH PURCHASE,
GOODS NEED TO BE RETURNED IN ORIGINAL PACKAGING.

Safety and Care Advice
!
Important-Please read these instructions fully before starting assembly
If you are unhappy with the product and wish to return it,
please following the retailer’s returns procedure.
Components - Panels
Make sure you have enough
space to lay out the parts
before starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close to
its final position (in the same
room) as possible.
Assemble on a soft, level
surface to avoid damaging the
unit or your floor.
We do not recommend the
use of power
drill/drivers for
inserting screw,
as this could
damage the unit.
only use hand screwdrivers.
Dispose of all packaging
carefully and responsibly.
Care and Maintenance
This product should not be
discarded with household
waste.Take to your local
authority waste disposal centre.
From time to time check
that there are no loose
screws on this unit.
Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
2
1
2 2
44
3
5
7
66
10
10
10
9
8
Check you have all the
components and tools listed
on pages 2,3 and 4.
Remove all fittings from the
plastic bags and separate
them into their groups.
Keep children and animals
away from the work area,
small parts could choke if
swallowed.

Components - Panels
Please check that you have all the components listed below before constructing your item.
Important-Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please email [e-mail]
If you have damaged or missing components,
email: [e-mail]
Part No Description Qty Thickness
(mm)
1
2
3
4
5
6
7
8
Right Side Panel
Bottom Panel
Back Panel
15 mm
15 mm
15 mm
15 mm
15 mm
15 mm
15 mm
1
2
1
2
1
2
1
1
3
Upper Centre Horizontal Panel
Upper Centre Vertical panel
Top panel
3 mm
Centre Vertical panel
Left Side Panel
Centre Horizontal Panel
Lower Centre Vertical panel
1
3
15 mm
15 mm
9
10

Components - Fixings
Please check that you have all the components listed below before constructing your item.
Important-Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please email [e-mail]
If you have damaged or missing components,
email: [e-mail]
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
0
mm
10
515 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170 175 180
Ruler - Use this to measure your screws (mm)
Tools Required ( Not Provided)
(A) (B) (D)( C )
(F) (H)( G ) (I)
JCBC M5 X 40mm
X 16
Dowel (M8X25)
X 24
Leg Pin
X 8
Allen Key
X 1
4
M3.5 X 20mm
X 4
Wall Plug
X 4
Strap
X 2
Bracket
X 4
M4 X 32mm
X 4
HARDWARE
ANTI - TIPPING KITS
(E)
(J)
Nail
X 60

3a .Fix the Back board to the back, with
Nail using a small hammer .
Note: The “Center” back board should be
located in the center as shown.
10
D
Attach Part & to assemble the cube
with JCBC Screw and tighten using Allen key.
89
A
A
A
A
A
8
9
Assembly Instructions If you have damaged or missing components,
email: [e-mail]
Step 1
Step 2
Step 3
B
B
B
B
B
B
B
B
B
B
B
B
1
2
2
34
4
56
6
7
C
3b. Attach Leg pin to the bottom panel
as shown , using a small hammer.
C
C
C
C
C
C
C
C
D10
10
10
Insert Wood Dowel to the pre-drilled holes of panel , ,
B
5
2 3
, & and assemble in the layout as shown.
4 65
CENTER
A
A
A
A

4th
I
I
J
F
I
2nd
H
G
I
CENTER
Step 4
Step 5
1st
WALL
Drill
Bit
6mm
Attach the Anti-tipping kit onto wall
following the steps as shown.
Assembly Complete
Attach Anti-tipping bracket to the back with
Screw and tighten using a Screw driver.
I
G
6