GoFly Easy Drone User manual

Operation Manual
Read before
ying!
IMPORTANT
Easy Drone
easyaerial.com
Easy Drone

Contents
01 This is Easy Drone
03 Parts
04 Charger
06 Frame Assembly
07 Learn to Fly
11 Safety
12 Altitude Hold Mode
13 First Flight
18 Stabilize Mode
18 Loiter Mode
19 Return-to-Launch Mode
19 Autonomous Mode and Missions
21 Specications and Resources
22 Learn More and Support

01
This is Easy Drone
Congratulations on getting your Easy Drone!
Easy Drone is an autonomous quadcopter powered by open-source
hardware, software, and rmware. Please read this manual carefully
before your rst ight and pay closeattention to safety information.
Happy ying!
!Important note : When using a GoPro always ensure
that the WiFi on the GoPro is turned OFF.

02
Flybot
Frame
L
Video transmitter
Easy Drone consists of two components
Gimbal and camera
ports
Safety button
Micro USB Port
Foldable landing gear

03
Parts
RC transmitter
Your direct link to Easy Drone
Telemetry Radio
Wirelessly change settings from computer or tablet
Also used for “Follow me” mode
Battery kit
4S Battery, charger, and contacts
Video receiver kit
Plug your screen or head mounted display
to get video feed from your camera
(requires 12V power source)
Quick snap-on adapters for gimbal and GoPro camera

04
Charger
Easy Drone is powered by a rechargeablelithium polymer (LiPo) battery.
Store battery at halfcharge then chargefully before ying. Batteries must
ship at half charge, so please charge before your rst ight. Each full battery
provides 10 to 13 minutes of ight time.
Connect charger to the
power adapter cable and
a wall outlet.
Connect the red cable to the
+ port and the black cable
to the -port.
Set the charger to
LiPo and 3A.
Connect the white
connector to the 4S port.
Join the two yellow
connectors together.
1
2
+
–
LiPo 3A
3

05
Charge until the status
indicator displays green.
Charging Complete
4
Protect battery from extremeheat, extreme cold, puncturing,
and ammable surfaces.
Charge battery using a designated LiPo balance charger only.
Always monitor battery while charging.
Flying with a low battery is a safety riskand can render thebattery
unusable. Always discontinue use when you receive a low battery
notication, and always y with a fully charged battery.
you observe any swelling ofthe package or the battery ceases to
function, locate your localbattery recycling center to dispose of
the battery. In the US and Canada, visit call2recycle.org to nd a
location. Donot dispose of thebattery in the trash.
!Battery Safety

06
Easy Drone frame consists of four color coded arms with motors and
propellers. Follow the easy steps below to assemble the frame.
Frame Assembly
Repeat the process with the other two arms.
Take the two sub-assemblies and put them together to nish your frame.
Look at it from the side to make sure it’s straight and hand-tighten the
black thumbscrews.
Take the left arm in your left hand and the (same color) right arm in
your right hand and plug the end of the right arm into the ring on
the left arm.
1
2
3

07
Control Easy Drone in ight using the transmitter’s
left and right sticks.
left stickright stick
Lower stick
to decrease
altitude.
Before takeo, set
stick fully down.
To maintain altitude,
set stick to center
position.
Take o by raising stick
halfway to center.
To increase altitude, raise
stick slowly.
left stick
Move theleft stick forward and backward to control altitude and acceleration.
Throttle
Learn to Fly
Land by setting stick
fully down once Easy
Drone is a few inches
above the ground.

08
Flight Tip
When adjusting orientation, move the left stick horizontally without changing its
vertical position.
Move stick to the
left to rotate
counterclockwise.
Move stick to
theright to
rotate clockwise.
left stick
Release stick to
stop rotating and
maintain current
orientation.
Move the left stick horizontally to rotate Easy Drone and change orientation.
For a slow rotation, move the stick slightly away from the center
in either direction. Moving the stick farther from the center creates
a faster rotation.
Yaw
ef Stick