GOKKO GK-27 User manual

GOKKO REPEATER PEDAL LOOPER GK-27
Instruction Manual
AUDIO & ACCESSORIES
REPEATER PEDAL
Congratulations! You have purchase Gokko REPEATER Looper
WWW.GOKKOAUDIO.COM
www.facebook.com/gokko.audio
FOLLOW US ON
You can then press the footswitch again, onto RED mode, to record another layer of the loop,
and again into BLUE mode to mark the endof the loop.
Power up REPEATER Looper
Record Tap footswitch once until the LED going to RED mode
Switch to Playback Tap footswitch again to replays the loop the LED should
be BLUE at this point
Undo/Redo last recording Double tap footswitch
Double tap and hold the footswitch
Stop and delete the loop
Resume playback Tap footswitch again
Delete the loop Press and hold the footswitch
(when Repeater is disengaged)
Recording your first loop
To start recording, press the footswitch once.
The LED will light up in red, indicating Repeater Looper is in Record Mode.
At the end of the loop (eg after eight bars), press the footswitch again.
The LED will turn blue, and Repeater Looper will repeat the loop continuously.
The LED will blink every time Repeater Looper reaches the starting point of the loop.
Your loop can be up to ten minutes long.
Setting loop playback volume
To change the playback volume of the loop you just recorded, adjust the knob labelled “Level”.
The Loop Level knob only controls loop playback level, it has no influence on the signal from your
instrument
Using Undo/Redo
Creatively Undoing and redoing overdubs can be used for more than just correcting mistakes.
You can make your performance more interesting by removing and bringing back sections.
Here is a simple example:
-Record a bass line (loop cycle 1).
-Record some chords (loop cycle 2).
-Record a melody (loop cycle 3).
-Press and hold the footswitch to remove the melody.
-Improvise or record something else.
-Press and hold the footswitch again to bring back the previously recorded melody.
Please note that undoing or redoing by using the footswitch is only possible during playback.
Holding down the footswitch after stopping loop playback/recording will delete the loop!

#toneisthesecret
Follow Gokko Audio on Instagram and hastag our own
Stopping loop playback/recording
To stop loop playback or recording, press the footswitch twice in short succession.
The LED will start flashing in blue to indicate that your loop is still in memory and ready for playback.
To get the most out of your setup and the loops you’re recording, place Repeater Looper at the end of
your signal chain. This gives you the flexibility to add parts with or without signal processing, switching
effects on and off as required.
Stopping loop playback/recording and deleting the loop
To stop loop playback/recording and delete everything you have recorded, press the footswitch twice in
short succession and hold down your foot on the second tap.
The LED will turn off to indicate that the loop has been deleted. At this point, you can start recording
loops from scratch again.
Deleting the loop when you are not recording or playing back
To delete everything you have recorded, press the footswitch twice in short succession and hold down
your foot on the second tap. The LED will turn off to indicate that the loop has been deleted.
When you delete your loop from Repeater Looper, the device goes into True Bypass mode
Storing the current loop
When you power down Repeater Looper and a loop is in memory, it will be stored automatically.
When you power up Repeater Looper again, the LED will flash in blue, indicating your previously
recorded loop is available. Just hit the footswitch, and playback will start.
If you want to start from scratch, delete the loop as described in the previous paragraph.
Overdubbing
When you’re happy with your loop, you can start overdubbing.To record another take (overdub),
press the footswitch again while the original loop is playing back. The LED will turn red,
indicating you’re in Record mode again. When you’re done, press the footswitch once more to quit
Record mode. Repeater Looper will repeat the loop with both the original recording and the overdub.
Please note that the length of the loop will never increase when overdubbing. When you continue
playing, you will simply create additional overdubs. You can record as many overdubs as you like
there is no limit.
Undo (deleting the last take)
To undo (delete) the last take you recorded, simply press and hold the footswitch for 1.5 seconds or
longer. The LED will blink twice in rapid succession, and the last take will be deleted.
Redo (restoring a previously deleted take)
If you have deleted the last take and you changed your mind, you can restore that take. To do so,
simply press and hold the footswitch for 1.5 seconds or longer. The LED will blink twice in rapid
succession, and the previously deleted take will be restored.
GOKKO REPEATER PEDAL LOOPER GK-27