Goldair GI200 User manual

GI200: 220 - 240V, 50Hz ~, 1100-1300W, Steam Iron
Steam Iron
Model GI200
OPERATING INSTRUCTIONS

GENERAL CARE AND SAFETY GUIDE
Please read all instructions carefully before using this appliance and keep them for
future reference.
Thank you for choosing a Goldair Steam Iron. This Goldair appliance has been
designed and manufactured to a high standard of engineering and with proper
use and care, as described in this leaflet, will give you years of useful service.
Please read these instructions carefully.
ALWAYS
✔Always ensure hands are dry before
handling the plug or switching on the Steam
Iron.
✔Always use the Steam Iron on a secure,
dry, level surface.
✔Always use the Steam Iron on an ironing
board, or similar surface.
✔Always unplug from the socket when not in
use and before cleaning.
✔Always allow the Steam Iron to cool before
cleaning and storing.
✔Carry out regular checks of the supply cord
to ensure no damage is evident.
✔Return the Steam Iron after a malfunction,
or if it has been damaged in any manner to an
authorised electrician for examination, repair
or adjustment as special purpose tools are
required.
✔The Iron must be rested on a stable
surface.
NEVER
✘Never touch hot surfaces.
✘Never use this appliance outdoors.
✘Never use this appliance for any purpose
other than its intended use. This appliance is
for household use only.
✘This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge, unless they are
supervised or have been given instruction
concerning the use of the Steam Iron by a
person responsible for their safety.
✘Close supervision is necessary when the
appliance is near children.
✘Never leave the appliance unattended
when in use as clothing and material can
burn.
✘Never place this appliance on or near a hot
gas or electric burner or where it could touch a
heated oven or microwave oven.
✘Never immerse any part of the Steam Iron,
or cord set and plug in water or any other
liquid to protect against electrical hazards.
✘Never use harsh, abrasive or caustic
cleaners to clean this appliance.
✘Never operate the appliance with a
damaged cord or plug, after it malfunctions, or
if it has been damaged in any manner.
✘The Steam Iron is not intended to be
operated by means of an external timer or
separate remote-control system.
✘The Iron must not be left unattended while
it is connected to the supply mains.
✘The plug must be removed from the socket-
outlet before the water reservoir is filled with
water.
✘The Iron is not to be used if it has been
dropped, if there are visible signs of damage
or if it is leaking.
CAUTION: This appliance generates heat
during use. Proper precautions must be
taken to prevent the risk of burns, scalds,
fires or other damage to persons caused by
touching the exterior whilst in use

COMPONENTS
BEFORE FIRST USE
Ensure any labels, tags or stickers that may be attached to the body or soleplate of the
iron are removed.
It is normal for a small amount of smoke and odor to be produced the first time your iron
is used, this is due to the initial heating of the materials used to make the iron. When
using the steam function for the first time do not direct the steam toward your garments,
as there could be debris from the steam vents that may damage the garment.
FILLING WITH WATER
We recommend the use of distilled water.
Ensure that both the steam control turning switch and temperature control dial are set to
the minimum/low heat position when filling.
Fill your iron only with water, do not add fabric conditioners, starches or any other
solution as these will damage the steam mechanism.
Hold the iron upright so that the water-filling inlet is in a horizontal position.
Fill by directing water though the water filling inlet until the water reaches the “MAX”
mark indicated on the side of the iron. Never fill above this mark.
SETTING THE TEMPERATURE
Follow instructions detailed on the label of the garment you wish to iron. If there are no
instructions, use the indicative chart following. If the garment consists of various fabric
types, select the temperature relevant to the most delicate of the fabrics that make up
your garment.
(1). Spray release
(3) Steam dial
(5). Shot-steam button
(7). Supply cord
(9). Transparent water tank
(11). Maximum water level
(13). Water measure
(2). Filler door
(4). Spray button
(6). Auto shot off indication light
(8). Cord bushing
(10).Thermostat knob for temperature regulation
(12). Plate with steam vents

STEAM IRONING
•Place the iron in a vertical position and set the temperature control dial at the
minimum/low heat setting.
•Insert the plug into the socket, and then turn the temperature control dial to the
“high heat” marking. The pilot light will come on, indicating that the iron is
heating up.
•When the pilot light turns off, the set temperature has been reached and the iron
is ready to use.
•During ironing, the pilot light on the iron automatically switches on/off as the
thermostat maintains the set temperature (you may continue ironing during this
process).
•Turn the steam dial to the required position.
•Steam is produced as soon as the iron is held horizontally.
SPRAYING
Press the spray button to spray water on your garment, as often as required.
Note: When using the water spray function, ensure that there is enough water in
the water tank.
Note: You may have to pump the spray button several times at first use.
BURST OR VERTICAL STEAM IRONING
Press the burst of steam button to generate a powerful burst of steam that can
penetrate the fabric and smooth the most difficult, tough creases. Wait for a few
seconds before pressing again.
By pressing the burst of steam button at intervals you can also iron vertically (i.e.
curtains and hanging garments).
Note: The burst of steam function can only be used at high temperature. Stop the
emission when the pilot light turns on. Start ironing again only after the pilot light
has turned off.
DRY IRONING
For ironing without steam, follow the instructions in the section “steam ironing”,
however, the steam control turning switch should be set to the “0” position. (no
steam).
Fabric Temperature Control Temperature Requirement
Synthetic Low Temperature
Silk, Wool Medium Temperature
Cotton, Linen High Temperature

SUPPORT AND TECHNICAL ADVICE
North Shore City, Auckland, New Zealand
Monday –Friday 8am-5pm
Phone: [phone]
Website: www.goldair.co.nz
SELF-CLEANING
The self-cleaning feature cleans inside the soleplate, removing impurities. We
recommend using it every 10 - 15 days.
Set the steam control turning switch to position “0” (no steam)
Fill the water tank to the “MAX” level.
Set the temperature control dial to full heat and wait for the pilot light to turn off.
Pull the plug out of the socket and press the self-cleaning button until the boiling
water, steam and impurities are ejected.
When the soleplate has cooled, it can be wiped with a damp cloth.
HOW TO CLEAN & STORE YOUR IRON
After using, tilt the water filling hole downward over a sink to empty the remaining
water from the water tank.
Insert the plug into the socket, and set the temperature control dial to “MAX” for 1-
2 minutes to evaporate the remaining water, unplug the iron and let it cool before
storing in an upright position.
From time to time, clean the exterior of the iron with a damp cloth and wipe dry.
If the iron has not been used for an extended period, hold the iron horizontally
and allow to steam for 2 minutes prior to ironing.

Your Goldair product has been inspected and tested and is guaranteed subject
to the following for a period to two years from the date of purchase against
defects in workmanship and materials. During this period, such defects will be
rectified by repair or replacement of the product purchased. Your product
contains no user serviceable components and this warranty becomes invalid if
in our opinion the product has been misused, abused, incorrectly installed,
tampered with, connected to an electrical supply not corresponding with the
name plate specification, or subjected to power surges. The warranty does not
include any labour or other associated expense that may be involved in
removal or installation of the product. Normal wear and tear is expressly
excluded.
If your Goldair product fails to operate satisfactorily, please return it to the
retailer from whom it was purchased. To obtain a repair or replacement
product under this warranty, you will need to produce satisfactory evidence of
date of purchase. The completed warranty and purchase receipt must be
presented with the product. The warranty should be filled out at the time of
purchase. It is in your interest to make sure this is done.
If the product is to be replaced (cannot be repaired) then that replacement will
be of the same or similar product or accessory excluding packaging,
instruction card etc. Where a replacement product is supplied, this shall be
guaranteed for the balance of the original warranty period.
Any model that is no longer available will be replaced by a model of a value
and with such features as we consider appropriate in the circumstances.
Goldair Ltd is not responsible for freight forwarding charges, losses or
damage in transit.
If service is required after the warranty period has expired, the product should
be returned to a qualified electrical technician. Service outside of the warranty
period will be at your cost.
Consumers Guarantee Act (1993).
In accordance with the above act consumers are advised that: The
manufacturer does not undertake that repair facilities and parts are
necessarily available for this product.
If any of the provisions of the foregoing are contrary to any relevant
legislation, then that provision shall be deemed to be excluded from the
warranty and the rest of the provisions will continue to apply.
TWO YEAR WARRANTY
IMPORTANT: PLEASE RETAIN THIS WARRANTY CARD
NAME:
ADDRESS:
PURCHASED FROM:
SUBURB:
DATE OF PURCHASE:
NAME OF PRODUCT:
MODEL No: