GOLDEN STATE INSTRUMENT GS-2800 CC User manual

HOW TO USE CAMERA ：
1) Connect a 75 ohm coaxial cable from the camera rear panel
BNC connector(video out) to a monitor.
2) Use only AC/DC power supply. Be sure to connect each lead to
appropriate terminal.
3) Once the image appears, adjust the focus of lens on an object
while looking at the monitor.
4) Screw the lens figer tightly into the C mount. If CS mount is
required, release 2 screws attaching the mounting base, also,
release one screw from the bottom of the camera,and one screw
from cover of camera.
INSTALLATION INSTRUCTION 5) If the lens has Video Drive Auto Iris, connect three wires to the
Read these instructions carefully before 4 pin plug as shown in figure below.
trying to put the device into operation. 6) If the lens has DC Drive Auto Iris, connect four wires to the 4
pin plug as shown in figure below.
INTRODUCTION
The 1/3 inch color camera has a Auto IRIS Pin Definitions
CCD image sensor and all solid state circuit VIDEO DC
which provide extremely long life and high DRIVER DRIVER
reliability with low lag and high burn resi- 1+12V DAMP-
stance, and is not subject to distortion from 2VIDEO DAMP+
magnetic, and the camera functions reliably 3NC DRIVE+
in a wide temperature range. 4GND DRIVE-
MAIN FEATURES 7) Slide the switch on the back panel to the position of
1) By applying high sensitivity, a minimum “ON ”.If electronic shutter function is required.
object illuminance of 0.8LUX(at F/1.2) 8) Slide the switch on the back panel to the position of
becomes possible. “OFF ”while the Auto Iris lens is being used.
2) Longevity and no image distortion. 9) Slide the switch on the side to the position of “VIDEO”
3) The camera can use a C mount or an optional in using the Video Drive Auto Iris lens. The switch should
CS mount lens ,therefore,general use of a variety be slided to the position of “DC ” for DC Drive Auto
of C mount or CS mount lenses is possible. Iris lens. For better performance in using the DC drive
4) CCD iris with electrical shutter,Max lens,the user may adjust the level adjustment (level) to
1/120,000 Sec. the right position.
5) DC12V INTERNAL SYNC. 10) Back Light Compensation is ON/OFF switch control.
AC24V AUTOMATIC LINE LOCK.
A. FUNDAMENTAL SYSTEM
1
2
34
1/3" COLOR SONY CCD CAMERA
VIDEO MONITOR
VIDEO OUT
GS-2800 CC
GOLDEN STATE INSTRUMENT CO.
1/3" COLOR CCD CAMERA
1/3" COLOR SONY CCD CAMERA
GS-2800CC
INSTRUCTION MANUAL
1/3" COLOR CCD CAMERA
GS-2800CC

INSTALLATION
SPECIFICATIONS
TV SYSTEM NTSC / PAL
PICK UP SIZE 1/3-inch Sony Super HAD* CCD Image Sensor
PICTURE ELEMENTS 811(H)×508(V) / 795(H)×596(V)
NUMBER OF PIXEL 370K
HORIZONTAL FREQUENCY 15.750 / 15.625KHz
VERTICAL FREQUENCY 60 / 50HZ
SYNC.MODE INTERNAL
SCANNING SYSTEM 2:1 INTERLACE
MIN.ILLUMINATION 0.8LUX F/1.2
HORIZONTAL RESOLUTION 470TV LINES(Max.)
AUTO SHUTTER FUNCTION 1/50,1/60 TO 1/120,000 sec
S/N RATIO 52dB(MIN) / 60dB (TYP) (AGC OFF)
WHITE CLIPPER 1 TO 1.1 Vp-p
VIDEO OUTPUT COMPOSITE 1.0Vp-p AT 75ohm
POWER REQUIREMENT AC24V ± 10% / DC12V ± 10%
POWER CONSUMPTION 3W / 250 mA
LENS MOUNT STANDARD "C" AND "CS" MOUNT
AUTO IRIS VIDEO/DC/A.E.S
AGC ON / OFF
ATW ON / OFF
MIRROR FUNCTION ON / OFF
DIGITAL ZOOM(2X) ON / OFF
OPERATION TEMPERATURE 10℃TO + 60℃
DIMENSIONS L3.94＂(100mm)× W2.4＂(60mm) × H2.0＂
(50 mm)
WEIGHT 280g
WARNING: Observe Correct Voltage and Polarity
Do Not Point Camera Directly Into Sun
Failure To Observe Warnings May Void Warranty
14256 Doolittle Drive · San Leandro, CA 94577 · 1-800-227-2330 · Fax[phone]
Website: www.goldenstateinst.com · E-mail: [e-mail]
Slide Switch For
Selecting AI Lens
Level Adjustment For
DC IRIS Lens
Video Output Connector To
A Video Monitor, etc.
Holes For Attaching Tripod
(Screws For Tripod U 1/4")
Auto IRIS lens Connector
1. AES
2. BLC
3. AGC
4. ATW
5. MIRROR
6. 2XZOOM
Level
VIDEO OUT
VIDEO
DC
AUTO
IRIS
GND
AC24V
2.4＂(60)
ON
ON
ON
OFF
OFF
OFF
DC12V
LED
2.0 ＂
(50)
3.94＂(100)
1/3" COLOR CCD CAMERA
GS-2800CC