goliath IGNITE B2256EF User manual

A S S E M B L Y I N S T R U C T I O N S
MODEL NO.
B2256EF
2L-7910-00
I G N I T E - 6 0 ”
B A S K E T B A L L S Y S T E M
2020 Escalade Sports
Escalade® Sports products may be manufactured and/or licensed under multiple patents.
Additional patents may be pending. One or more patents and/or pending patents may cover specific product.
See for more information.Goalrilla.com/legal
Tel: [phone]
E-mail: [email protected]
Please Do Not Return This
Product to the Store!
Contact HAMMER SPORT AG at:
HAMMER ITEM NO.
2102

P R E - A S S E M B L Y T I P S
P R E - A S S E M B L Y T I P S
1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before assembling or ordering
parts.
3. To make assembly easier, use the Hardware Identifier on page 7-9 to identify and sort all fasteners. Check all cartons for
kits. All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes may not align and
parts may not easily fit together. Leave locknuts slightly loose until you are instructed to tighten them.
5. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer has to be contacted for
replacement parts.
2
2L-7910-00
11 - 80 lb. bags of concrete
1 - Post hole digger (optional)
1 - wheel barrow
1 - Concrete form (see note after step 2)
ITEMS NEEDED (NOT INCLUDED)
1 - 15/16" Open end Wrench
1 - 15/16” Socket and Ratchet (optional)
1 - 9/16” Deep Well Socket & Ratchet
1 - 3/4” Socket and Ratchet (optional)
1 - 3/4” Open end Wrench
1 - Phillips Screwdriver
1 - Level
1 - Tape Measure
1 - Rubber Mallet
1 - Set of Padded
Saw Horses
1 - 9/16” Open end Wrench
1 - Cordless drill & 9/64” drill bit
1 - Safety glasses
1 - Ladder
2 - 7/16” Open end Wrench or 1 open end wrench & adjustable wrench
1 - garden hose
1 - 1/2” Socket & Ratchet (optional)
1 - 1/2” Open end Wrench
1 - 5/16” socket driver for cordless drill (used to assemble Board Pads)
1 - 7/32” Hex Key (included)
2020 Escalade Sports
WARNING
FAILURE TO FOLLOW THESE WARNINGS MAY
R E S U L T I N S E R I O U S I N J U RY A N D / O R
PROPERTY DAMAGE.
Owner must ensure that all players know and
follow these rules for safe operation of the system.
!Do not climb on the basketball stand;
!Do not hang on the rim/basket;
!Not intended for basketball games with
competitive character, only suitable for
practice of throwing techniques
!Install only on flat solid ground;
!Do not use in extreme wind or bad weather, the
basketball stand could tip over!
Contact HAMMER SPORT AG at:
Tel:
E-mail: [e-mail]
0731-97488-41
Please Do Not Return This Product To The Store!
Hammer Sport AG
Abt. Kundendienst
Von-Liebig-Str. 21
89231 Neu-Ulm

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
Owner must ensure that all players know and follow these rules for safe operation of the system.
Owner must ensure that all players know and follow these rules for safe operation of the system.
SAFETY INSTRUCTIONS
7
WARNING
FAILURE TO FOLLOW THESE WARNINGS MAY
R E S U L T I N S E R I O U S I N J U RY A N D / O R
PROPERTY DAMAGE.
Owner must ensure that all players know and
follow these rules for safe operation of the system.
!Do not dunk on this unit
!Do not hang from any part of the unit, including
the backboard, rim, support braces, or net.
!Do not slide, climb, or play on pole.
!Keep organic material away from pole base.
Grass, litter, etc. could cause corrosion and /or
deterioration.
!Check pole system for signs of corrosion
(rust, pitting, chipping). Remove rust and/or
loose paint completely and repaint with
exterior enamel paint. If rust has penetrated
through the steel anywhere, replace pole
immediately.
!Check system before each use for proper
ballast, loose hardware, excessive wear, and
signs of corrosion and repair before using.
!During play, use extreme caution to keep
players face away from the backboard, rim,
and net. Serious injury could occur if
teeth/face come in contact with backboard,
rim, or net.
!Wear a mouth guard when playing to avoid
dental injuries.
!When adjusting height, keep hands and
fingers away from moving parts.
!During play, do not wear jewelry (rings,
watches, necklaces, etc.). Objects may
entangle in net.
!Do not allow children to adjust system.
!Check system before each use for instability.
!Never play on damaged equipment. 4L-7609-00 3

4
ANCHOR SYSTEM INSTALLATION INSTRUCTIONS (Day 1)
Figure 1
3. Mix and pour concrete into hole. Follow instructions on
concrete bag. Stop about 18" below court level.
4. Insert four reinforcement bars (#40) into concrete 8" apart
creating a square in center on hole.
5. Finish pouring concrete up to court level.
6. Push anchor system into concrete and agitate to work out
voids in concrete. Immediately use a level to level and square
anchor plate to playing surface. Clean off any concrete that
may be on exposed threads.
Note: The bottom four nuts will be forever embedded
in concrete. The top four nuts remain on bolts and
INSTALLATION TIMELINE
1. Prior to anchor system and goal assembly, call utility services for location of underground utility lines before you dig.
2. Vertical main post assembly is a two part process.
PART 1
Day 1. Complete Anchor System Installation Instructions.
(Below)
Day 2-4. Allow concrete to cure.
PART 2
Day 5. Complete Goaliath® assembly instructions. (Requires
four adults)
Before digging hole for anchor system, check for
buried power, gas, water, and telecommunication
lines! Failure to do so could result in serious or fatal
injury! Contact your local utility company if unsure.
Note: For best results with less vibration, anchor system
should be independent of court. If pouring concrete for
both at same time, add an expansion joint in between.
Figure 2
2. Assemble anchor system as follows: Thread nut (#45) to bottom
of threads on anchor bolt (#50) insert threads of anchor bolt
(#50) through hole on anchor plate (#49) and secure with
nut (#45). Repeat this step for the
remaining anchor
bolts. See Figure
2. Note: Each leg
of anchor bolts
should face the
anchor bolt to the
right. See Detail A.
1. Determine the location of the anchor
system. The proper location is as close to
the court without making contact, as
shown in Figure 1. This,
however, is a general rule.
If you need to locate the
anchor system in a location other than
this, use the following dimensions as a
guide.
Overhang when adjusted to 10 ft. = 26”
20” Diameter
16” Diameter
Concrete
36”
Court
Court Level
Anchor Plate must be
square to your court so
the backboard will
line up with court.
Court
Top View
are used for leveling. (See Page 25).
OVERHANG
18 INCH
MINIMUM
REAR
CLEARANCE
REQUIRED
Note: When digging hole, if you hit rock
and cannot dig through contact a contractor.
Note: Minimum of 18” rear clearance is required behind pole.
THESE NUTS
USED FOR
LEVELING
Rebar
(Key #51)
Note: Failure to dig and fill hole as instructed will result
in increased system vibration.
Note: Using a concrete form for the top 4" of the concrete
is recommended. Cardboard forms can be purchased at
some hardware and home stores or a wooden form can
be constructed out of 2 x 4's.
*Tip: It is always a good idea to purchase two or three
extra bags of concrete, just in case you need them. If
extra bags are not used you can return them to the store.
Let concrete cure for a MINIMUM of 72 hours.
Items needed for Anchor Installation (not included)
9 - 80 lb. bags of concrete (2-3 extra recommended)
1 - post hole digger (optional)
1 - 15/16” open end wrench
1 - 15/16” socket and ratchet (optional)
1 - wheel barrow
1 - garden hose
1 - level
1 - tape measure
1 - concrete form (see note after step 2)
45
45
49
50

P A R T S L I S T ( N O T A C T U A L S I Z E )
5
BACKBOARD ASSEMBLY, 60" X 33"
6A-7799-10
QTY. 1
UPPER BOARD ARM ASSEMBLY
1A-7963-10
QTY. 2
LOWER POLE
1A-7961-10
QTY. 1
UPPER POLE
1A-7962-10
QTY. 1
MEDIUM WEIGHT RIM
6A-6374-01
QTY. 1
NET
3F-6081-00
QTY. 1
LOWER BOARD ARM ASSEMBLY
1A-7975-10
QTY. 1
BRACE, BOARD ARM
2S-9442-10
QTY. 1
RIM COVER PLATE
2S-6427-01
QTY. 1
23
4
5
1
6
LOGO ON
THIS SIDE
7
8
9
with Goaliath logo
(Packed together
with parts #8,9 & 14)
(Packed together
with parts #6,9 & 14)
(Packed together
with parts #6,8 & 14)

6
P A R T S L I S T ( N O T A C T U A L S I Z E )
ACTUATOR CAP
3M-8941-00
QTY. 1
PIVOT TUBE
8S-6658-00
QTY. 1
POST EAR
2S-6795-02
QTY. 2 HEIGHT DECAL
4L-8697-00
QTY. 1
ACTUATOR
4A-6605-00
QTY. 1
ACTUATOR SLEEVE
3M-6542-00
QTY. 1
BOARD PAD, RH
3M-6580-00
QTY. 1
BOARD PAD, LH
3M-6581-00
QTY. 1
TUBE PLUG, 4" SQUARE
3M-6850-00
QTY. 1
PULL PIN
7B-6255-00
QTY. 1
10 11
12
15
14
16 17
18
19 20
(Pre-assembled to part #12) (Pre-assembled to part #12) (Pre-assembled to part #3)
ACTUATOR HANDLE
4A-6606-00
QTY. 1
13
53
POST PAD
3M-8960-00
QTY. 1
(Packed with the owner’s manual)
(Packed together
with parts #6,8 & 9)(Packed in hardware kit)(Packed with actuator handle)

3/8-16 X 7.00 HHCS, ZINC GR 5
1B-6484-10
QTY. 2
3/8 - 16 X 7.5 " HHCS, Grade 5
1B-6483-10
QTY. 2
3/8-16 X 5" HHCS, GRADE 5
1B-6485-10
QTY. 2
3/8-16 X 6.25" HHCS, GRADE 5
1B-7188-00
QTY. 1
7
H A R D W A R E L I S T ( A C T U A L S I Z E )
21
22
23
24 Note: Base plate of Anchor kit is
located at the bottom of hardware kit
in the hardware carton.
3/8-16 X 2 3/4" HHCS
1B-6195-00
QTY. 2
5/16-18 X 1.75 HHCS, ZINC
1B-7190-00
QTY. 4
26
25

#8 X 1/2" SCREW
1B-6788-00
QTY. 4
8
H A R D W A R E L I S T ( A C T U A L S I Z E )
1/4-20 X 2.75 HHCS, ZINC
1B-7196-00
QTY. 1
1/2-13 X 1 1/2" HHCS
1B-6486-10
QTY. 1
3/8-16 X 1.50 CB, ZINC
1B-7187-00
3/8-16 X .625 SBHS, STAINLESS STEEL
1B-7189-00
QTY. 8
27 29
28
30
31
32
QTY. 4
#10 X 1.0 ZINC SELF DRILLING /
SSELF TAPPING SCREW
1B-6479-00
QTY. 6

H A R D W A R E L I S T ( A C T U A L S I Z E )
9
3/8" WASHER
701-50
QTY. 16
3/8 FLAT WASHER
2B-6114-00
QTY. 4
1/2" FLAT WASHER, ZINC
2B-6093-00
QTY. 2
STOP SPACER
8S-6657-00
QTY. 2
WASHER, 1/4" SAE FLAT
2B-6014-00
QTY. 2
5/16" WASHER
2B-6024-00
QTY. 8
1/4-20 LOCKNUT, ZINC
2B-6792-00
QTY. 1
5/16-18 NUT NYLOK ZINC
2B-6009-02
QTY. 4
3/8-16 LOCKNUT
901-28
QTY. 13
1/2-13 NUT NYLOK, ZINC
2B-6095-00
QTY. 1
33 34 35
36
37 38 39 40
41
42 43 44
7/32” HEX KEY
7B-8563-00
QTY. 1
52
NYLON WASHER,
0.38 ID X 1.25 OD
3M-6883-00
QTY. 8
NYLON SPACER,
0.4 ID X .78 OD X .25 THICK
3M-6269-00
QTY. 2

H A R D W A R E L I S T ( A C T U A L S I Z E )
10
5/8" FLAT WASHER
2B-6834-00
(QTY. 8)
*Hardware located in Anchor kit box
48
47
45 46
5/8"-11 HEX NUT
2B-6097-00
(QTY. 12)
5/8" SPLIT LOCK
WASHER
2B-6099-00
(QTY. 4)
5/8" THREAD
PROTECTOR
PLASTIC CAP
3M-9040-01
(QTY. 4)
*Parts located in Anchor kit box
P A R T S L I S T ( N O T A C T U A L S I Z E )
7X7 ANCHOR PLATE
2S-6453-00
(QTY. 1)
Goaliath “J” BOLT
(QTY. 4)
#3 X 30” REBAR
1S-6167-00
(QTY. 4)
2B-6112-00
50
49
51
(Packed in hardware Kit Carton)

11
CAUTION:
3/8-16 X .625 SBHS, STAINLESS STEEL
1B-7189-00
QTY.4
29
HARDWARE NEEDED (ACTUAL SIZE)
USE 7/32” HEX KEY WRENCH TO INSERT 2
FRONT BUTTON HEAD SCREWS AND 2 BACK
BUTTON HEAD SCREWS (#29). TIGHTEN
SCREWS COMPLETELY AT THIS TIME.
NOTE
WITH THE HELP OF ANOTHER ADULT CAREFULLY
LIFT UPPER POLE (#3) AND SLIDE INTO LOWER
POLE (#2). HOLES IN POLES SHOULD LINE UP
WITH NO GAP BETWEEN POLES.
NOTE
2
3
PINCH POINTS! DO NOT place your
hand or any fingers in any of these
locations when inserting the pole.
KEEP CHILDREN AWAY FROM THE ASSEMBLY AREA.
TWO CAPABLE ADULTS ARE NEEDED FOR THE
FOLLOWING STEPS.
TOOLS NEEDED
7/32”
Packed in hardware kit.
29
29

12
3/8-16 X .625 SBHS, STAINLESS STEEL
1B-7189-00
QTY.4
29
HARDWARE NEEDED (ACTUAL SIZE)
2
3
KEEP CHILDREN AWAY FROM THE ASSEMBLY AREA.
TWO CAPABLE ADULTS ARE NEEDED FOR THE
FOLLOWING STEPS.
TOOLS NEEDED
7/32”
Packed in hardware kit.
29
USE 7/32” HEX KEY WRENCH TO INSERT 4 SIDE
BUTTON HEAD SCREWS (#29). TIGHTEN
SCREWS COMPLETELY AT THIS TIME.
NOTE
29

13
HARDWARE NEEDED (ACTUAL SIZE)
1/4-20 X 2.75 HHCS, ZINC
1B-7196-00
QTY. 1
30
WASHER, 1/4" SAE FLAT
2B-6014-00
QTY. 2
38
1/4-20 LOCKNUT, ZINC
2B-6792-00
QTY. 1
44
2
3
44
38
30
38
7/16”
TOOLS NEEDED
7/16”
INSTALL BOLT (#30), WASHERS (#38) AND NUT (#44)
INTO JOINT REINFORCEMENT BUSHINGS AS SHOWN.
TIGHTEN (#30) BOLT AND NUT (#44) UNTIL SECURE.
NOTE
TOOLS NEEDED
7/32”
Joint
Reinforcement
Bushings

Prepare a flat area that is clear of debris. Keep children
away from the assembly area. Two capable adults are
needed for the following steps.
NOTE:
MAKE SURE THAT THE POLE IS SECURE ON THE
SAWHORSES AND NEVER LEAVE IT UNATTENDED.
14
PLACE POLE ASSEMBLY ON TWO
SAWHORSES AS SHOWN.
NOTE
NOTE
Place the end of the pole close to where
the anchor system is located. This will
make it easier when you set the post
assembly upright.
Previously installed
Anchor System.
32” Minimum

HARDWARE NEEDED (ACTUAL SIZE)
15
14
9/16”
TOOLS NEEDED
9/16”
3/8" WASHER
701-50
QTY. 4
36
3/8-16 LOCKNUT
901-28
QTY. 2
42
42
36
24 36
3/8-16 X 5" HHCS, GRADE 5
1B-6485-10
QTY. 2
24
ATTACH POST EARS AS SHOWN. Tighten
hardware about 3/4ths of the way. Leave loose
enough to attach Actuator on page 18.
NOTE

16
HARDWARE NEEDED (ACTUAL SIZE)
3/8-16 X 7.00 HHCS, ZINC GR 5
1B-6484-10
QTY. 1
22
3/8" WASHER
701-50
QTY. 2
36
3/8-16 LOCKNUT
901-28
QTY. 1
42
9/16”
TOOLS NEEDED
9/16”
42
36
36
22
WASHER 0.38 ID X 1.25 OD,
NYLON
3M-6883-00
QTY. 2
34
34
4
4
LOGO
FACES OUT
IT IS IMPORTANT FOR THE INSTALLER TO
UNDERSTAND THE NECESSITY OF THE NYLON
WASHERS (#34) PROVIDED. THESE WASHERS
ADEQUATELY SPACE PAINTED PARTS AT THE
PIVOT POINTS. NEGLECTING THE USE OF THESE
WASHERS WILL RESULT IN RUSTED PARTS.
NOTE
Make sure Goaliath
lettering is right side
up as shown.
42
36
36
22
34
4
HELPFUL HINT:
To secure item #34 (3M-6883-00) Nylon Washer in position for assembly use
several small strips of tape, drops of hot melt glue or other adhesive.
Make sure Nylon Washer is positioned correctly before securing.
Attach Lower Arm (#4) to the holes that are centered on the pole, the
offset holes will be used for a later step (for arm stops). Tighten
hardware but back off half a turn once you feel the hardware is
snug. Make sure Nylon Washers (#34) are installed between the arms
and Pole as shown.
NOTE

17
12
19
16
18
PIVOT TUBE (#16) MUST GO THROUGH THE ACTUATOR CAP (#19),
ACTUATOR SLEEVE (#18) AND THE STEEL ACTUATOR TUBE (#12).
NOTE
16
HARDWARE NEEDED
16
PIVOT TUBE
8S-6658-00
QTY. 1
(Packed in hardware kit)

18
HARDWARE NEEDED (ACTUAL SIZE)
1/2-13 X 1 1/2" HHCS
1B-6486-10
QTY. 1
27
1/2" FLAT WASHER, ZINC
2B-6093-00
QTY. 2
33
1/2-13 NUT NYLOK, ZINC
2B-6095-00
QTY. 1
41
41
33
33
27
17
12
3/4”
TOOLS NEEDED
3/4”
Attach actuator (#12) to post ears as shown, tighten
but leave loose enough for actuator to pivot. At this
time attach the Actuator handle (#13) with pin (#17).
NOTE
13
PULL PIN
7B-6255-00
QTY. 1
17

HARDWARE NEEDED (ACTUAL SIZE)
3/8-16 X 7.00 HHCS, ZINC GR 5
1B-6484-10
22
3/8" WASHER
701-50
QTY. 2
36
3/8-16 LOCKNUT
901-28
QTY. 1
42
WASHER 0.38 ID X
1.25 OD NYLON
3M-6883-00
QTY. 2
34
34
9/16”
TOOLS NEEDED
9/16”
36
36
42
Pivot actuator up and attach to the lower board arm assembly.
Tighten hardware but back off half a turn once you feel the
hardware is snug. Make sure Nylon Washers (#34) are installed
between the arms and Actuator pivot tube as shown.
NOTE
Pivot
Tube
(#16)
19
If needed extend the actuator by turning
the handle clockwise until the actuator
Pivot tube hole lines up with the holes
on lower board arm.
NOTE
QTY. 1
22

20
Tighten Lock Nuts (#42) that hold the post
ears until tight.
NOTE
9/16”
TOOLS NEEDED
9/16”
42