Gordon 94114 User manual

SKU 94114 For technical questions, call 1-800-444-3354 Page 1
OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2006 by Harbor Freight Tools®. All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
Save This Manual
You will need the manual for the safety warnings and precautions,
assembly instructions, operating and maintenance procedures, parts list and
diagram. Keep your invoice with this manual. Write the invoice number on
the inside of the front cover. Keep the manual and invoice in a safe and dry
place for future reference.
LIGHTED TRUNK EXTENDER
94114
Due to continuing improvements, actual product may differ slightly from the product described herein.
The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.

SKU 94114 For technical questions, call 1-800-444-3354 Page 2
Specifications
There are no Replacement Parts for this Product
Save This Manual
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. Keep your
invoice with this manual. Write the invoice number on the inside of the front cover. Keep
the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using this product, basic safety precautions should always be
followed to reduce the risk of personal property and damage to equipment. Read
all instructions before using this product!
1. Do not operate the product if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgment/reflexes might be impaired.
2. Never use this product as a towing rope.
3. Before using this product, check with the local Department of Motor Vehicles for
required safety regulations when using this product.
4. Do not let children play with this product. It is not a toy.
5. Activate the Flashing Emergency Light to indicate caution when using this product.
Activate the solid red light when using this product at night.
6. Do not operate the product if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgment/reflexes might be impaired.
7. Do not wear loose clothing or jewelry as they can be caught in moving parts.
8. Protective gloves and nonskid footwear are recommended.
9. Wear restrictive hair covering to contain long hair.
10. Use eye and ear protection. Always wear ANSI approved impact safety goggles
when setting up this product.
11. Maintain proper footing and balance at all times.
12. To avoid risk of personal injury, equipment damage, fire and shock, make sure your
work area is free of damp, wet or rainy conditions. Keep area free from clutter.
13. Use this product for its intended use only. Never force this product to do the work of
a larger industrial tool. This product is not for towing.
Note: This product is used for securing the Trunk of your vehicle in place while holding a
light load. Always use ropes, chains, or other appropriate devices to safely hold a
larger load in place.
Dimensions
Material
Finish
Wire
Light
Cutter
Power
Source
Net Weight
3.25”L X 3.75” Square X 1.25”T
Hi Impact ABS, Stainless Steel, Two Red LED’s, Twisted Steel Wire,
Die Cast Hook (Qty. 2).
Silver w/Black Trim. Chrome Plated Fasteners.
Spring Loaded-Extends 4’-10” w/Snap-clip Black Slider, Locks Wire Down.
2-Way Push Button. Stays lit or Flashes.
5/8” Serrated Edge Blade
AAA 1.5V Batteries (Qty. 2) (Batteries Included)
.55 Lbs.

SKU 94114 For technical questions, call 1-800-444-3354 Page 3
OPERATING INSTRUCTIONS
Your Trunk Extender comes fully assembled. It is important that you read the entire
instructional sheet to become familiar with the product before using.
1. Distribute the load in the opened Trunk
evenly. Push the Hook (A) over the Trunk
lock. This holds the Trunk Extender in
place. See Figure 1.
2. Pull the Hook (B) with the Wire and clip it
to the underside of the trunk lid.
See Figure 2.
3. Lower the trunk lid down to the desired
position. The Wire will self-retract. Push the
Lock Button on the side of the case
forward. Lock the taut wire in place.
(Caution: Do not mistake the Cutter Button
for the Wire Button).
See Figure 3 and 4.
4. Test the Wire and the load in the trunk
before driving. Make sure the load is
secured properly, and will not fall out of the
trunk.
5. Before driving away, activate the red light
on the Trunk Extender by pushing the
plastic casing on the light inward. Push
once for a solid red light and twice for a
flashing red light. Figures 5 & 6.
Figures 1, 2, & 3
Lock at
Bottom of
Trunk
Secure
Hook (B)
w/Wire
Under
Trunk Lid
Figure 5
Plastic
Cover
over the
Red Light
Trunk Lid
UNPACKING
When unpacking your Trunk Extender, if any part is missing or broken, please call
Harbor Freight Tools at 1-800-444-3353
Figure 4
Wire and
Lock
Button
Hook (B) w/Wire
Hook (A)
Figure 6
Hook (A)
Cutter
Button
Caution: Always drive at a
safe, reduced speed when
using this product. During
the trip, stop the vehicle and
check the load periodically.

SKU 94114 For technical questions, call 1-800-444-3354 Page 4
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING
OUT OF HIS OR HER REPAIRS TOTHE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR
ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Carton Cutter
1. To use the Carton Cutter, push the Snap-click black button forward. This button is
spring loaded and will retract the Blade when released. (There is no replacement
part for this blade). Use with caution. See Figure 7.
Snap-click
Black
Button
Figure 7
Replacing Batteries
Figure 8
2. Always dispose of batteries properly. Contact you local Hazardous Waste Authority
for proper battery disposal guidelines.
AAA Batteries
(Qty. 2)
Battery
Cover
1. Remove the old batteries (note the polarity of the old batteries). Make certain that
the new batteries are AAA 1.5V Batteries (Qty.2). Install the new batteries into the
Battery Housing. Make certain that the batteries are placed according to the correct
polarity. Replace the Battery cover. See Figure 8.
Blade WARNING:
Be extremely careful
when handling and
using this SHARP
blade. When using
the Trunk Extender,
be careful not to
inadvertently slide
open the blade.