Goulds AqWiFi Instructions for use

AqWiFi
ABOUT GOULDS WATER TECHNOLOGY
Goulds Water Technology, a Xylem brand, is one
of the world’s leading brands in residential and
commercial water products. The brand began in
1848 in Seneca Falls, NY, when Seabury S. Gould
purchased a pump making business. Today,
Xylem’s Goulds Water Technology brand is a
leader of residential, commercial and agricultural
products globally.
For more information on residential
water products and applications,
visit http://residential.goulds.com/
AqWiFi
QUICK INSTALL
Goulds is a registered trademark of
Goulds Pumps, Inc. and is used under license.
© 2017 Xylem Inc.
AQWIFITRI November 2017
Xylem Inc.
2881 East Bayard Street Ext., Suite A
Seneca Falls, NY 13148
Phone: [phone]
www.gouldswatertechnology.com
Add Device
• Open the AqWiFi
app and login to the
dealer account.
• Tap the add device
icon
• Enter the Device ID
by tapping Tap to
Scan QR code.
Scan the QR code to
ll in the Device ID.
• Enter the customer
name and email.
• Tap Add Device
• A conrmation email is sent to the dealer and
customer. If the customer has not already registered,
the conrmation email will contain a temporary
password. The customer can use this to login.
• Install the AqWiFi
app on customer
device.
• Login to the
customer account.
• Accept the Terms of
Service by tapping
I agree
• The AqWiFi is now installed and can be monitored
by the dealer or customer.

Mount
• Mount indoors or outdoors in a location with
adequate Wi-Fi connection.
• Install the screw and wall anchor from the
mounting kit into wall structure. Hang the AqWiFi
on the screw and tighten the screw to secure.
Wire
• Turn off power to the controller and wait 5 minutes
for hazardous voltage to discharge.
• Remove ½” knockout from controller. Lower left
side is recommended.
• Install ½” NPT cable gland in to the enclosure
knockout.
• Insert cable from AqWiFi through the cable gland.
• Connect the ends of the cable to the adapter
board.
• Plug the adapter board in to the communication
port on the controller.
• Tighten the cable gland nut to seal the cable entry
(40-50 in-lbs.)
Power
• Follow the START UP PROCEDURE in the controller
IOM. Apply power to the controller. The AqWiFi
status LED will blink slow red indicating the device
is in Ofine Mode and ready for commissioning.
Connect to WiFi
• Install the AqWiFi app on
dealer device.
• Go to Wi-Fi settings and connect to AqWiFi.
Enter password Xylem12345.
• Open the AqWiFi app.
• Select Wi-Fi Setup
• Tap “AqWiFi-XXXXXX_Prov”
1. Select WPS Push Button and press Next
2. Follow the instructions on the app
a) Press PUSH
b) Press the WPS push
button on the
router within
2 minutes.
Create Dealer Account
NOTE: Skip to ADD DEVICE if dealer account was
already created.
• Open the AqWiFi app. • Select Register
• Select Dealer
• Fill in the account data and tap Submit
• Accept the Terms of Service by tapping I agree
• A conrmation email is sent to the email address
used to create the account.
AqWiFi
AqWiFi
SAFETY INSTRUCTIONS: Disconnect and lockout
electrical power before installing or servicing any
electrical equipment. All electrical work must be
performed by a qualied technician.
3. Press OK.
The app returns to the login screen.
For other connection options, see IOM.
Locate the WPS button on your
AP. Click on the “PUSH” button
below. Press the WPS button on
your AP within 2 minutes.
Please wait while we look for nearby
access points
Cancel
PUSH
The conguration is complete. Your
device will connect to the AP through
WPS. You may close this application.
OK