Grace Company G Series User manual

Quilt Motion
QCT and Wiring Instructions
Copyright December 12, 2018
Grace Company
(Reproduction Prohibited)
Version 1.1

ii
?
X
Warranty
1-800-264-0644
Warranty Information for your Quilt Motion.
The Quilt Motion has a One-Year limited warranty on all parts. The Grace Company will repair or replace,
at its discretion, any part with problems due to our manufacturing or defects in materials. This warranty
does not cover parts damaged through misuse, improper storage, improper assembly, loss, natural
events, and willful destruction. Parts must be returned to the Grace Company, shipping prepaid, before
we can repair or replace them. We will promptly return the repaired/replaced part at our expense if done
within a year of the purchase date.
|Warranty Quilt Motion

iii
Q’nique 15
Turn to page 1
Q’nique 21
Turn to page 13 G-Series 2 Top Plate Turn to page 19
Q’nique 19
Turn to page 7
G-Series Top Plate Rev1
Turn to page 24
|Choose your Machine Quilt Motion
G-Series Top Plate Rev2
Turn to page 29
The G-Series Top Plate revision can be identified by the holes on the front of the handles.
Rev1 does not have holes on the front of the handles Rev2 has holes on the front of the handles

1
|Q’nique 15” Machine Quilt Motion
QCT Bracket
Step 1: Attaching the Tablet Mount - Q’nique 15”........................................................................ 2
Wiring Instructions
Step 2: Cord Setup for the Bottom Carriage............................................................................... 4

2
Step 1 - Attaching the Tablet Mount
Parts Needed:
1-1: Using the 2mm Allen Wrench loosen all (4) set
screws on the QCT Bracket Q’nique 15.
1-2: Place the QCT Bracket Q’nique 15 onto the
handle bars as shown until the locater tabs snap
into place.
1-3: Use the 2mm Allen Wrench to tighten the (2)
set screws on each side of the QCT Bracket Q’nique
15.
Tools Needed:
2mm Allen Wrench
|Q’nique 15” Machine Quilt Motion
Tablet Tray (1) QCT Bracket
Q’nique 15 (1)
3 Wing Plastic
Knob M6 (1) Set Screw
2mm Allen Wrench
QCT Bracket Q’nique 15
Set Screw
Push in
tab using
a flathead
screwdriver if
necessary

3
1-5: Install the Tablet Tray to the QCT Bracket
Q’nique 15 using the 3 Wing Knob M6.
1-6: Loosen the circled M4 x 10mm SBHCS in
order to adjust the arms of the Tablet Tray to t
your tablet.
1-4: Use the 2mm Allen Wrench to tighten the
(2) set screws on the front of the QCT Bracket
Q’nique 15.
1-7: Slide your tablet into the Tablet Tray.
Tighten the screws that were loosened in step
1-6.
|Q’nique 15” Machine Quilt Motion
M4 x 10mm SBHCS M4 x 10mm SBHCS
M4 x 10mm SBHCS
Set Screw
2mm Allen Wrench
3 Wing Knob M6
Tablet Tray
Tablet

4
Step 2 - Cord Setup for the Bottom Carriage
Parts Needed:
2-1: Connect the USB-A to USB-B Cable to the
Motor Plate Control Box. 2-2: Connect the opposite end of the USB-A to
USB-B Cable to the USB Port on the back of your
machine.
|Q’nique 15” Machine Quilt Motion
USB-A to USB-B
Cable (1) Quilt Motion Cable (1)
Zip Tie Mount (2) Cable Wrap (1)
Male to Male USB
Adapter Cable (1) Zip Tie (2)
USB-A to USB-B Cable
USB-A to USB-B Cable
Motor Plate Control Box

5
2-4: Connect the opposite end of the Quilt Motion
Cable to the Blue Port on the back of your machine.
2-3: Connect the Quilt Motion Cable to the Motor
Plate Control Box.
2-5: Connect the Male to Male USB Adapter Cable to the port on the top of your machine. Connect the
opposite end to your tablet.
|Q’nique 15” Machine Quilt Motion
Quilt Motion Cable
Quilt Motion Cable
Male to Male USB Adapter Cable

6
2-6: Secure Zip Tie Mounts to the Bottom Carriage. Wrap USB-A to USB-B Cable and Quilt Motion Cable
together in the Cable Wrap and route cables as shown.
Note: Be sure to leave enough slack in the cables to allow for full range of motion of the machine.
|Q’nique 15” Machine Quilt Motion
USB-A to USB-B Cable
Quilt Motion Cable
Male to Male USB Adapter Cable
Bottom Carriage
Zip Tie Mount Zip Tie Mount

7
QCT Bracket
Step 1: Attaching the Tablet Mount - Q’nique 19”........................................................................ 8
Wiring Instructions
Step 2: Cord Setup for the Bottom Carriage..............................................................................10
|Q’nique 19” Machine Quilt Motion