Grandstream Networks GXV3662 series User manual

Grandstream Networks, Inc.
GXV3662 User Manual

GXV3662 IP Camera
Firmware 1.0.1.22 Page 2 of 36
Grandstream Networks, Inc. 03/2011
Safety Instructions
These instructions are intended to assist users with the operation of the GXV3662 and also to
instruct on how to avoid dangerous situations or damage to the device.
Warnings: Serious injury or death may be caused if any of the warnings below are neglected.
Cautions: Injury or damage to the equipment may occur if any of the following caution
messages are neglected.
Warnings Follow these safeguards to prevent
serious injury or death.
Cautions Follow these precautions to
prevent potential injury or material
damage.
Warnings:
Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power
Source with DC 12V according to the IEC60950-1 standard. Please refer to the technical
specifications for more details.
Do not use a third-party power adapter or power cord
When the device is installed on the wall or ceiling, make sure that it is firmly attached.
Notice：
Make sure that the power supply voltage is correct before using the camera.
Do not drop the device or expose it to physical shock.
Do not expose the device to temperatures outside the range of -30oC to +50oC PSU and PoE
mode when the device is in operation.
Do not expose the device to high electromagnetism radiation.
To avoid heat accumulation, make sure that your operating environment has proper
ventilation.
Do not attempt to open, disassemble, or modify the device
Afew parts (e.g. electrolytic capacitor) of the equipment shall be replaced regularly according
to their average life time. The average life time varies from the differences between operating
environments and usage history. Regular maintenance checks are recommended for all
users. Please contact your dealer for more details.

GXV3662 IP Camera
Firmware 1.0.1.22 Page 3 of 36
Grandstream Networks, Inc. 03/2011
Note：
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.

GXV3662 IP Camera
Firmware 1.0.1.22 Page 4 of 36
Grandstream Networks, Inc. 03/2011
Contents
Welcome .........................................................................................................................................................5
Package Contents............................................................................................................................................6
Product Overview...........................................................................................................................................7
GXV3662 Top View...............................................................................................................................7
GXV3662 Side View ..............................................................................................................................7
GXV3662 Bottom View .........................................................................................................................7
GXV3662 Inside connections.................................................................................................................8
GXV3662 Sample Connection Diagram...............................................................................................10
GXV3662 Key Features........................................................................................................................10
GXV3662 Lens Specification...............................................................................................................11
Minimum Recommended System Requirement ...................................................................................12
Connect your GXV3662.......................................................................................................................12
Configuring the GXV3662 via Web Browser...............................................................................................13
Access the GXV3662 Web Configuration Menu..................................................................................13
Connect the Camera to a DHCP server.................................................................................................13
Connect to the Camera Using a Static IP. .............................................................................................14
GXV3662 Home Web Page..................................................................................................................15
GXV3662 System Time and Name Page..............................................................................................16
GXV-3662 Video & Audio Page...........................................................................................................17
GXV3662 Networking Page –Assigning an IP to the GXV3662 .....................................................19
GXV3601 DDNS Page.........................................................................................................................20
GXV3662 SIP Page ..............................................................................................................................21
GXV3662 Status Page ..........................................................................................................................23
GXV3662 User Management Page.......................................................................................................24
GXV3662 Maintenance Page ...............................................................................................................24
GXV3662 SMTP Page..........................................................................................................................25
GXV3662 FTP Page.............................................................................................................................26
GXV3662Alarm Event.........................................................................................................................26
GXV3662 Motion Detection Page........................................................................................................29
Configure Motion Detection & AlarmActions.....................................................................................30
GXV3662 System Log..........................................................................................................................31
FAQ...............................................................................................................................................................32

GXV3662 IP Camera
Firmware 1.0.1.22 Page 5 of 36
Grandstream Networks, Inc. 03/2011
Welcome
The GXV3662 is a next generation IP camera for remote monitoring and surveillance over
your LAN or internet.
The GXV3662 combines best in class IP video technology and SIP protocols for a robust IP
surveillance solution. The product features H.264 video streams with up to 30 frames per
second at 720p resolution, delivering rich image clarity at rapid transmission rates. Integrated
SIP can pass alarms to the PSTN, mobile phones, SIP IP phones, SIP videophones and
enables 2-way VoIP communication.
The GXV3662 ensures ease of use, integration and deployment with a multilingual graphical
user interface. The GXV3662 can be quickly installed and connected to your network and
accessed from anywhere over the internet. Grandstream‘s flexible video management
software enables users to monitor multiple environments in one easy to use application. The
intuitive web interface lets users easily access, manage, view and record live video streams
from the device.
The GXV3662 is a powerful solution for small to medium sized offices, homes and storage
facilities looking to safeguard their valuables.

GXV3662 IP Camera
Firmware 1.0.1.22 Page 6 of 36
Grandstream Networks, Inc. 03/2011
Package Contents
Items in the package:
GXV3662 IP Camera
12V DC power Adapter attached to terminal block
8-pin terminal block connector –8-pin connector block for connecting external devices,
such as infrared detector, smoke detector, emergency lights, etc., to Alarm IN and
Alarm OUT. You can also connect microphones and powered speakers through the
audio in and audio out ports.
Quick installation guide
Alignment sticker
Tool set containing a hex key, 3 plastic anchors and 3 screws

GXV3662 IP Camera
Firmware 1.0.1.22 Page 7 of 36
Grandstream Networks, Inc. 03/2011
Product Overview
GXV3662 Top View
GXV3662 Side View
GXV3662 Bottom View

GXV3662 IP Camera
Firmware 1.0.1.22 Page 8 of 36
Grandstream Networks, Inc. 03/2011
GXV3662 Inside connections
Indicators and Connectors inside the camera
1
Internal temperature
regulator
It adjusts the temperature to ensure the camera works
normal under different weather.
2
SD card slot
SD card slot.
3
Reset
Press the Reset button for 6 seconds to perform a
factory reset.

GXV3662 IP Camera
Firmware 1.0.1.22 Page 9 of 36
Grandstream Networks, Inc. 03/2011
4
Alarm/Audio
NOTE: GXV3662 does not support zoom
Type
Port
Description
AUDIO
GND
Audio Output
OUT
IN+
Audio Input
IN-
ALARM
IN+
Alarm Input
IN-
O+
Alarm Output
O-
5
Network
10/100 Switch LAN port for connecting to Ethernet. The
indicator will be steady for connection and flashing for
network activity.
6
Power
Type
Description
12V
12 V DC input
GND
Ground
7
Lens
For adjusting the lens, unscrew the housing and adjust
the lens vertically/horizontally. Screw the housing back
when adjustment is done.
Note: Loosening the screws on both sides of axle might
be necessary for adjusting the lens vertically.

GXV3662 IP Camera
Firmware 1.0.1.22 Page 10 of 36
Grandstream Networks, Inc. 03/2011
GXV3662 Sample Connection Diagram
GXV3662 Key Features
The table below lists the key features the GXV3662 Supports.
Features
GXV3662
Image Sensor
1/3‖, 1.2 Megapixel CMOS, 1280H x 960V, day and night mode,
exceptionally low noise levels and low light sensitivity. Shutter time: 1/30 to
1/1000 seconds
Lens Type
1/3‖, 3.3-12mm, F1.6-F3.2 (F1.4-F2.9), DC-Iris, Manual focus: 50cm - ∞,
H: 89.8°‐ 23.9°, V: 63.6°‐ 17.9°
Day & Night
YES, CDS Sensor, mechanical IR Cut filter
Minimum
Illumination
0.05 lux
Responsitivity
6.0V/lux-sec (550nm)
Max Frame
Rate
1280 x960 @ 30fps
Pixel Dynamic
Range
Wide Dynamic Range of 120dB with SNRMAX 44dB
Supported
Video
Resolutions
30fps for 1280x960, 1280x720, 1024x768, 800x592, 800x480, 640x480,
640x368, 480x368, 480x272, 320x240, 320x176, 256x192 and 256x144 all
at 30 fps
Video Bit Rate
64 Kbps –8 Mbps, multi rate for preview and recording
Audio Input
LINE-IN
Audio Output
LINE-OUT
Alarm Input
VIN≤45V, IIN≤35mA

GXV3662 IP Camera
Firmware 1.0.1.22 Page 11 of 36
Grandstream Networks, Inc. 03/2011
Alarm Output
125VAC/0.5A, 30VDC/2A, Normal Open
Audio
Compression
G.711a/u
Serial Ports
N/A
IRIS Control
DC-IRIS
Embedded
Analytics
Motion detection (up to 16 target areas), video loss
(pending)
Pre-/post-alarm
Buffer
24MB
Snapshots
Triggered upon events, send via email/FTP
Multi-streaming-
rate for Preview
& Recording
Yes
Security
Video watermark (pending), HTTPS, admin/anonymous
Network Port
10M/100M auto-sensing, RJ45
Network
Protocol
TCP/UDP/IP, RTP/RTCP, RTSP, DHCP, DDNS, HTTP,
HTTPS, SMTP, FTP, NTP
Power over
Ethernet (PoE)
IEEE 802.3af default class
Peripheral Ports
Internal SDHC 2.0 socket
SIP/VoIP
Support
Yes
Dimensions (D
x H)
153mm x 115mm
Weight
1.19kg
Temperature /
Humidity
-30C - +50C (-22F- +122F) for DC and PoE, With heater &
fan
Humidity 10-90% RH(non-condensing)
Power Adapter
Output: 12VDC/1A; Input: 100–240VAC, 50–60Hz
Casing
Vandal proof and weatherproof with IP66 standard
Compliance
FCC, CE, C-tick, IP66
GXV3662 Lens Specification
Parameters
GXV3662
Lens Format
1/3”
Image Sensor
1/3” CMOS
Focal Length
3.3mm –12mm
Aperture Ratio
F1.6 –F3.2
View Angle
D:125.7°- 29.9°
H: 89.8°-23.9°
V: 63.6°-17.9°
IRIS
DC AUTO
Minimum Object
Distance
50 cm
IR CUT Filter
Yes

GXV3662 IP Camera
Firmware 1.0.1.22 Page 12 of 36
Grandstream Networks, Inc. 03/2011
Minimum Recommended System Requirement
Windows 2000 Server Professional, Windows XP, Windows Vista.
CPU: Intel Pentium 4 or higher, 2 GHz.
RAM: 1 GB (4 GB recommended for larger systems).
Support for DirectX 8.0 and above.
.
Connect your GXV3662
Using the Power adapter as power supply
Connect an RJ-45 cable to the NETWORK port of the GXV3662.
Connect the other end of the RJ-45 cable to your network or PC.
Connect the power supply to the DC 12V connector block inside the GXV3662.
Connect the other end of the power supply to a wall outlet. The POWER LED will turn
solid green.
Using PoE as power supply:
Connect an RJ-45 to the NETWORK port of the GXV3662.
Connect the other end of the RJ-45 cable to a PoE switch. The POWER indicator will
turn solid green.
NOTE: If you are going to connect the device to a hub/switch/router, please use a
straight-through cable. Acrossover cable should be used if you are going to connect the
device directly to a PC.

GXV3662 IP Camera
Firmware 1.0.1.22 Page 13 of 36
Grandstream Networks, Inc. 03/2011
Configuring the GXV3662 via Web Browser
The GXV3662‘s embedded Web server responds to HTTP/HTTPS GET/POST requests.
Embedded HTML pages allow you to configure your IP camera through Microsoft Internet
Explorer.
Access the GXV3662 Web Configuration Menu
Connect the Camera to a DHCP server.
1. Navigate your browser to:
http://www.grandstream.com/support/gxv_series_surveillance/general/resources/gs_
search.zip
2. Run the Grandstream GS_Search tool, that you just downloaded.
3. Click on the button in order to begin device detection
4. The detected devices will appear in the Output field
5. Start Internet Explorer ® on your computer.
6. Enter device IP in the address bar of the browser.
7. Enter the administrator user name and password to access the Web Configuration
Interface
8. The default user name and password are both set to admin.
9. IE will indicate that ―This website wants to install the following add-on:
‗GSViewerX.cab‘ from ‗Grandstream Networks Inc‘.‖ Install this add-on by following
the instructions in IE.
10. You will see the home page.

GXV3662 IP Camera
Firmware 1.0.1.22 Page 14 of 36
Grandstream Networks, Inc. 03/2011
Connect to the Camera Using a Static IP.
If the camera does not get a response from the DHCP server after 3 minutes, it can be
accessed by the default IP 192.168.1.168.
1. Connect your PC to the same network as the GXV3662.
2. Configure the IP address of your PC to: 192.168.1.XXX (1<XXX<255) and configure
the subnet mask to 255.255.255.0.
3. Make sure that the device is turned on and connected to the network.
4. Start Internet Explorer on your computer.
5. Enter 192.168.1.168 in the address bar of the browser.
6. Enter the administrator user name and password to access the Web Configuration
Interface
7. The default user name and password are both set to admin.
8. IE will indicate that ―This website wants to install the following add-on:
‗GSViewerX.cab‘ from ‗Grandstream Networks Inc‘.‖ Install this add-on by following
the instructions in IE.
9. You will see the home page.

GXV3662 IP Camera
Firmware 1.0.1.22 Page 15 of 36
Grandstream Networks, Inc. 03/2011
GXV3662 Home Web Page
Figure 2: Home web page of GXV3662-HD
Items on GXV3662 Home Page
1
Motion Detection
If the motion detection alarm is triggered, the indicator will flash
red. Click on the indicator to turn off the alarm.
2
Alarm Event
If an alarm event is triggered, the indicator will flash red. Click
on the indicator to turn off the alarm.
3
Control Console
PTZ Console controller. PTZ is not supported in the GXV3662
4
ZOOM
NOTE: The GXV3662 does not support zoom
5
FOCUS
Adjusts the focus of images.
6
Default
Click this option to reset the video brightness, contrast, and
saturation to their factory default configuration.
7
SPEED
Adjusts the rotation speed of the console.
8
BRIGHTNESS
Adjusts the image brightness.
9
CONTRAST
Adjusts the image contrast.
10
SATURATION
Adjusts the image saturation.
11
View Size
Resize the image to fit into the window panel in the home
scream.
12
Language
Chose between English and Chinese

GXV3662 IP Camera
Firmware 1.0.1.22 Page 16 of 36
Grandstream Networks, Inc. 03/2011
13
Play
Displays the video in the main frame
14
Capture
Captures the image displayed and saves it to C:\GS_Capture
(default directory).
15
Record
Records the video and saves it to C:\GS_Record (default
directory).
16
Sound Off/On
Toggles the sound On or Off.
17
Talk
Establishes two-way audio.
18
Playback
Replays the saved video.
19
Config
Configures the Save Location for captured images and
recorded videos.
GXV3662 System Time and Name Page
This page allows you to configure the system settings on the GXV3662.
Current System Time - displays the
current date and time (24h clock).
Set the System Time
Update via NTP Server
- the camera will obtain
the time from an NTP
server, specify the NTP
server's IP address or
host name. And you can
select your time zone
from the drop-down list or define your own time zone setting.
NOTE: If using a host name for the NTP server, a DNS server must be configured under
Basic Settings -> Networking.
Synchronize with Local Computer - sets the time from the clock on your computer.
Set the Time Manually - this option allows you to manually set the time and date.
OSD Date Format - set the format of the
date on OSD
Device Name Setting -This
field lets you configure the name
of the GXV3662, which helps

GXV3662 IP Camera
Firmware 1.0.1.22 Page 17 of 36
Grandstream Networks, Inc. 03/2011
GSurf and GS_NVR to indentify the device when using GS_Search to search all the
Grandstream network cameras or digital video cameras in the same subnet.
GXV-3662 CMOS Settings Page
Flip –Enable this option to flip the image 180 degrees
Iris Setting –Select from either automatic, where the iris would open or close depending on
the environment conditions, or set it to manual where the user can select from having it open
100/80/60/40/20 percent
Shutter Speed –Select from either automatic shutter speed depending on the environment
conditions, or select one of the available shutter speeds from 1/30 to 1/1000th of a second.
IR CUT Setting –Select from either manual or automatic. If the user selects manual then
select from either daytime mode or night mode. If the user selects automatic, then select a
sensitivity value from 1 to 5 that adjusts the best to the environment conditions.
Color Mode –Select from either color, black and white or automatic
GXV-3662 Video & Audio Page
On Screen Display (OSD) Settings
OSD Time/ Text –The time stamp and channel name displayed on the screen.

GXV3662 IP Camera
Firmware 1.0.1.22 Page 18 of 36
Grandstream Networks, Inc. 03/2011
Video Settings
Preferred Video Codec –The GXV3662 supports the H.264 video codec.
Resolution –The higher the resolution is, the better the video quality is, and higher
bandwidth is required.
Low -----------------------High Resolution
QCIF CIF 2CIF 720p
Bit Rate –The number of bits that are
conveyed or processed per unit of time.
Maximum Frame Rate –The video frame
rate is adjustable based on network
conditions. Increasing the frame rate will
increase the amount of data significantly
therefore consuming more bandwidth. Video
will be impaired due to packet loss when
there is insufficient bandwidth.
Bit Rate Control –Variable Bit rate (VBR)
and Constant Bit Rate (CBR).
Variable Bit Rate - If VBR is selected, the codec varies the amount of output data per time
segment. VBR produces a better quality-to-space ratio. The bits available are used to enable
more flexibly and encode sound or video data more accurately, with fewer bits used in less
demanding passages and more bits used in difficult-to-encode passages.
Constant Bit Rate - If CBR is selected, the codec‘s output data is constant regardless of the
input data. The output bit rate is defined in ―Bit rate‖. CBR is useful for streaming multimedia
content on limited capacity channels. It is easier to calculate required bandwidth as well as
the required storage space using CBR.
Image Quality –If ‗Bit Rate Control‘ is set to ―VBR‖, ―Image quality‖ needs to be configured.
The better the video quality is, the higher the bit rate will be.
I-frame Interval –While streaming video over a network, compression technologies are used
to show the incremental difference between each frame. I-frames are used to help keep the
video looking normal. When intervals are shorter, the video quality is higher but uses more
bandwidth.
NOTE: The users might need to configure the Primary Stream and Secondary Stream
properly. Sometimes, the user might like to watch the live video stream from the web GUI in
low resolution mode while recording a copy via GSurf/GS_NVR in high resolution due to the
limitation of internet bandwidth. In this case, for example, primary stream can be configured
to have better resolution, and then the users can use primary stream to record while watching
secondary video streams.
Audio Settings
Preferred Audio Codec –The GXV3662 supports up to 2 different Vocoder types, a-law
(PCMA) and u-law (PCMU). The audio can also be turned off by switching the setting to
―Disabled‖

GXV3662 IP Camera
Firmware 1.0.1.22 Page 19 of 36
Grandstream Networks, Inc. 03/2011
Microphone Volume: The user can adjust the volume gain of the microphone on a range
from 1 to 5
Speaker Volume: The user can adjust the speaker volume on a range from 0 to 31
Power Frequency - this setting should match the power frequency used in the country to
avoid flickering in the image. Users can select between 50Hz indoor, 60Hz indoor and
outdoor.
GXV3662 Networking Page –Assigning an IP to the GXV3662
The GXV3662 supports IP version 4. The IP address can be set automatically via DHCP, or a
static IP address can be set manually. To make the GXV3662 work properly, the user needs
to set the DNS configuration properly. For security purposes, the user can also assign the
GXV3662 an HTTP Port other than 80.
IPAddress Configuration
The GXV3662 operates in two modes:
Dynamically Assigned via DHCP
–all the field values for the Static IP
mode are not used. The GXV3662
acquires its IP address from the first
DHCP server it discovers on its
LAN.
Statically Configured as –
configure all of the following fields:
IP address, Subnet Mask, Default
Gateway IP address. These fields

GXV3662 IP Camera
Firmware 1.0.1.22 Page 20 of 36
Grandstream Networks, Inc. 03/2011
are set to zero by default. Static IP addresses are recommended for the GXV3662
DNS Configuration
There are two methods of DNS
configuration on the GXV3662:
1. The GXV3662 can obtain the DNS
server automatically
2. Users can configure their own
preferred DNS server
HTTP Port
The GXV3662 supports user configured
http ports. If the HTTP port is changed, the
port number is needed to access the web
GUI, for instance: http://192.168.1.168:8080.
NOTE: If the HTTP Port is 80, when you add this device to GSurf or GS_NVR, the RTSP
port is 554. If the HTTP Port is changed, when you add this device to GSurf or GS_NVR,
please make sure the RTSP port number equals HTTP Port plus 2000.
GXV3601 DDNS Page
Dynamic DNS provides devices that have a variable, often changing IP address with a well
known hostname resolvable by network applications through standard DNS queries.
Set up DDNS
1. Apply for a domain name
from your service provider.
2. Login to the web
configuration page, click
Basic Settings > DDNS.
3. Enter the required
information
DDNS Active –If you
want to use DDNS, please
set this field to ―Enabled‖ .
DDNS ISP Type –Select
your DDNS ISP Type.
Self-Define DDNS Address –Self-define the DDNS server instead of using DDNS