Grandview GPCM-D3040 User manual

Details of installation
Height Adjustment
Take apart the ornament cap of main bar (2-3) and loosen the front
positioning screws. Adjust the subsidiary bar (2-3) to reqiured
position, and then install the ornament cap of main bar (2-3) as figure
9 (the main bar of GPCM-D3040 is seperated by 8 segments, each
segment is 16mm; the main bar of GPCM-D4060 is seperated by 15
segments, each segment is 16mm)
Installation of main bar
1.Firstly, please confirm how many installation holes the projector has
3 or 4.
2.If there are 3 holes, the installation arms (4-2) need to be taken apart
from Installation bracket firstly. Connect 3 installation arms(4-2) to the
projector, and then connect the installation arms (4-2) to the installation
base (4-5) However,the installation base needs to be the center of
projector. Figure 12.
3.Connect the installation arms to the projector conversely if the
distance of installation holes is less than 120mm. Connect the
installation arms (4-2) to the installation base (4-5) via sliding
installation button (4-4) as figure 13
4.Rotate the adjustable screw(4-3) for adjusting the height of instllation
arms (4-2) if the installation holes are not at the same level as figure 14.
5.The front or back of adjuster must be parallel to the surface of
projector as figure 15.
Angle Adjustment
1.Loosen the positioning screws (front and back) for adjusting the
angle, and then rotate the screwdriver for fine turning to the required
angle as figure 10.
2.Loosen the positioning screws (left and right) for adjusting the angle,
and then rotate the screwdriver for fine turning to the required angle as
figure 11.
Wires collection
Take apart the ornament cap of main bar (2-5) after connecting the
GPCM Main Bar Overview to the fixation (1-1), then stay the power
cord into the storage gap. At last, re-install the ornament cap of main
bar (2-5) as figure 6、 7 and 8.
Scope of
adjustment: 10mm
Instruction Manual
Projector Ceiling Mount
Applicable Model
GPCM-D3040
GPCM-D4060
Please read before using
Thank you for purchasing our
products. Please read the
instruction manual carefully
in order to ensure this
projector lift is suitable for
your projection equipment.
Cautious
Warnings For safety, the minimum of ceiling must be 20KGweight
Caution Please do not incline the projector the extremely.
Please do not take apart the accessories of projector
ceiling mount.
Do not
take apart
figure 6 figure 7 figure 8
figure 9
figure 10 figure 11
figure 12
figure 13 figure 14
figure 15
The front or back of
adjuster must be
parallel to the surface
of projector
vertical tilt:±15°
The angle of The nagle of
horizontal tilt:±5°
Weight The maximum weight of installation bracket is 20Kg
Grandview Crystal Screen
Canada Ltd.
#11- 3751 North Fraser Way,
Marine Way Business Centre,
Burnaby, BC, Canada V5J 5G4
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.ca
Guangzhou Grandview Crystal
Screen Co., Ltd.
No.43,Guomao Road South, Hualong Town,
Panyu District, Guangzhou City, China
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.com
www.grandviewscreen.com.cn

Parts
GPCM-D is combined by GPCM and GPD
GPCM Main Bar Overview
1-1 Fixation
1-2 Top Cap
2-1 Main Bar
2-2 Subsidiary Bar
2-3 Ornament Board of Main Bar
2-4 Ornament Board of Subsidiary Bar
2-5 Ornament Cap of Main Bar
GPD Adjusting Overview
3-1 Adjuster
3-2 Hanging Button
3-3 Horizontal Adjusting
Hole
4-1 Installation Bracket
4-2 Installation Arm
4-3 Adjustable Screw
4-4 Sliding Installation
Button
4-5 Installation Base
4-6 Vertical Adjusting
Button
Install the fixation on the ceiling (screws of accessory①)
as figure 1. GPCM-D can be installed to the concrete-
roof with ceiling or without ceiling,such as figure 2 and
figure 3.
1
3
Scope for installation (Installation hole of projector):
Maximum scope for installation:360mm diameter
Minimum scope for installation:50mm diameter
Note: Connect the installation arms to the projector conversely for different installation
holes of projector.
Maximum diameter: 360mm
Connect the GPCM Main Bar Overview to the fixation
(screws of accessory ②).Store the power wire, and then
fasten the front and back screws of main bar. Finally,
install the ornament board of main bar as figure 4.
2
Three steps of installation
Scope for installation (H is the distance between ceiling and projector)
The H of GPCM-D3040 is 300mm~400mm
The H of GPCM-D4060 is 400mm~600mm
GPCM-D3040 GPCM-D4060
Scope
Accessories:
① M6x25 Tapping Screw (3sets)
② M5x10 Philips Screw/
Washer/Spring Washer (4sets)
③ M4x8 Socket Cap Screw (6pcs)
④ M5x8 Philips Screw (2pcs)
⑤ M3x8 Philips Screw (4pcs)
⑥ M4x8 Philips Screw (4pcs)
⑦ M5x8 Philips Screw (4pcs)
1-1
1-2
2-1
2-4
2-3
3-1
3-3
2-2
3-2
2-5
figure 4
Fasten the front
and back screws
of main bar.
Minimum diameter: 50mm
Scope
Hang the installation bracket (projecter has been
installed) to the adjuster as figure 5. And then put in the
screws (accessory ④)，but do not faster.
Install the
top cap
Connect main bar
and adjuster (screws
of accessory ③)
figure 5
figure 1
figure 2
figure 3
Three steps of installation
4-1
4-2
4-3
4-4
4-5
4-6
H
H