Grandview GPCN-D200 User manual

vertical tilt:±15°
The angle of
Instr uction Manual
GRANDVIEW REPRODUCING GENUINE COLORS
P roje c tor C e iling M ount
A pplic a ble M ode l
G P C N - D 2 0 0
G P C N - D 3 0 /4 0
G P C N - D 4 0 /6 0
P le a s e r e a d b e fo r e u s ing
Thank you for purchasing our
products. Please read the
instruction manual carefully
in order to ensure this
projector lift is suitable for
your projection equipment.
Cautious
Warning F o r s a fe ty , the m in imum of c e ilin g m us t be 1 0 K Gwe ig ht
Caution P le a s e do no t inc lin e the pr oje c tor the e x tre m e ly.
Please do not take apart the accessories of projector
ceiling mount.
Do not
take apart
D e ta ils o f ins ta lla tion
W ir e s c o lle c tio n
If th e v olume o f po we r w iv e s a r e le s s th a n dia m e te r o f m a in ba r ( 2 - 1 )
th a t ple a s e put this p ow e r w ir e s ins ide the m a in ba r dir e c tly . B u t if the
volum e is g re a te r tha n the dia me te r, ple a s e ta ke a pa r t b a c k orm a ne nt
bo a rd ( 2- 4 a n d 2 - 5 ) a n d p os ition in g butto n ( 2- 6 ) fr om m a in ba r ( 2 -
1 )a s figure 8 . A nd the n s ta y the p ow e r c or d in to the m a in b a r ( 2- 1 ) ,
figu re 9 F ina lly , re - ins ta ll the ba c k orna me nt bo a rd ( 2- 4 ) from th e
othe r e nd, a n d th e n in s ta ll pos itio ning butto n ( 2- 6 ) a nd ba c k or na m e nt
bo a rd ( 2 - 5 ) , f ig ur e 1 0 .
H e ig ht a dju s tme nt
A djus t the m a in ba r ( 2- 1 ) to re qu ir e d he ight a fte r ta kin g a pa r t th e fro nt
orna me nt boa r d ( 2- 3 ) a nd lo os e nin g th e fro nt pos itio ning s c re w. A n d
th e n, re - ins ta ll th e fro nt po s itio ning s c re w a nd the fr on t o rn a me nt
bo a r d ( 2 - 3 ) , f ig u re 1 1 . ( T he h e ig ht o f G P C N - D 2 0 0 c a n n o t b e
a djus te d ; the m a in b a r of G P C N - D 3 0 /4 0 is s e p e ra te d by 4 s e g me n ts ,
e a c h s e g me n t is 2 5 mm ; the m a in b a r of G P C N - D 4 0 /6 0 is s e pe ra te d by
8 s e gm e nts , e a c h s e g me nt is 2 5 mm)
A n g le a d ju s tm e n t
1 . L oo s e n the p os itio ning s c re ws ( fro nt a nd ba c k ) fo r a dju s ting the
a n gle , a nd the n rota te the s c r e wdr iv e r fo r fine tur ning to th e re quire d
a ngle a s f igu re 1 2 .
2 . L oos e n the pos itio ning s c r e ws (le ft a n d righ t) fo r a djus ting the a n gle ,
a n d the n r ota te th e s c re w driv e r for fine tur ning to th e r e quire d a n gle a s
figu re 1 3 .
The nagle of
horizontal tilt:±5°
In s ta lla tion o f m a in b a r
1 .F irs tly, ple a s e c onfirm how m a ny in s ta lla tion ho le s the pro je c tor ha s ?
3 o r 4
2 . If the re a re 3 h ole s , th e in s ta lla tion a rm s (4 - 2) n e e d to be ta k e n a pa rt
from Ins ta lla tio n bra c ke t fir s tly. C o nne c t 3 ins ta lla tion a rms (4 - 2) to th e
pro je c to r, a nd t he n c o nne ct the i n s ta lla tion a rm s ( 4 - 2) t o t he i ns ta lla tion
ba s e ( 4 - 5 ) H o we ve r ,th e ins ta lla tion ba s e ne e d s to be th e c e nte r o f
pro je c to r. F igu re 1 4 .
3 . C o nn e ct the in s ta lla tion a rm s to th e pro je c to r c on ve rs e ly if the
d is ta n c e of ins ta lla tio n ho le s is le s s tha n 12 0 m m. C on ne c t th e
in s ta lla tion a rms ( 4 - 2 ) to the in s ta lla tion ba s e ( 4- 5 ) v ia s liding
in s ta lla tion b utton ( 4 - 4) a s f igu re 1 5
4 .R ota te the a dju s ta ble nuts ( 4- 3 ) for a d jus ting the he ig ht of in s tlla tion
a rms ( 4 - 2 ) i f the i n s ta lla tion h o le s a r e n o t a t the s a me l e ve l a s f igur e 1 6 .
5 .T he fro nt or ba c k of a djus te r m us t be pa ra lle l to the s urfa c e of
pro je c to r a s f igure 1 7.
figure 1 4
figure 1 5 figure 1 6
figure 1 7
G randview C rystal
Screen C anada Ltd.
#11- 3751 North Fraser Way,
Marine Way Business Centre,
Burnaby, BC, Canada V5J 5G4
Tel: [phone]
Fax: [phone]
Website: www.grandviewscreen.ca
G uangzhou G randview
Crystal S creen C o. , L td.
P.O. 511400 Federal Ind. Zone No. 363,
Yushan West Road,Shiqiao, Panyu
District, Guangzhou, Guangdong, China
Tel: [phone]
Fax: [phone]
Website: www.grandviewscreen.com
The front or back of
adjuster must be
parallel to the surface
of projector
Scope of
adjustment: 10mm
figure 8 figure 9 figure 1 0
figure 1 1
figure 1 2 figure 1 3

1-1
1-2
1-3
2-1
2-2
2-3
3-1
3-2
3-3
4-1
4-2
4-3
4-5
4-6 4-4
2-6
2-4
2-5
1
3
2
Install on
the flat
ceiling
GPCN-D200 GPCN-D30/40 GPCN-D40/60
Connect
main bar
and adjuster
(screws of
accessory ④)
Parts
GPCN-D is combined by GPCN and GPD
GPCN Main Bar Overview
1-1 Top Cap
1-2 Fixation
1-3 Sliding Adjusting Hole
2-1 Main Bar
2-2 Subsidiary Bar
2-3 Front Ornament Board
2-4 Back Ornament Board of Main Bar
2-5 Back Ornament Board of Subsidiary Bar
2-6 Moving Button
GPD Adjustment Overview
3-1 Adjuster
3-2 Hanging Button
3-3 Horizontal Adjusting
Hole
4-1 Installation Bracket
4-2 Vertical Adjusting Hole
4-3 Installation Arm
4-4 Adjustable Nut
4-5 Sliding Installation
Button
4-6 Installation Base
Accessories:
① M6x25 Tapping Screw (4sets)
② 6x50 Wood Screw (4pcs)
③ M5x8 Philips Screw (2pcs)
④ M5x10 Philips Screw (6pcs)
⑤ M5x30 Philips Screw (4pcs)
⑥ M4x30 Philips Screw (4pcs)
⑦ M3x30 Philips Screw (4pcs)
Scope for installation (Installation hole of projector):
Maximum scope for installation:310mm diameter
Minimum scope for installation:40mm diameter
Note: Connect the installation arms to the projector conversely for different installation
holes of projector.
Scope
Maximum diameter: 310mm Minimum diameter: 40mm
Scope for installation (H is the distance between ceiling and projector)
The H of GPCN-D200 is 200mm
The H of GPCN-D30/40 is 300mm~400mm
The H of GPCN-D40/60 is 400mm~600mm
Scope
Three steps of installation
Install the fixation on the ceiling (screws of accessory ① or ⑧ )as
figure 1, and the fixation also can be installed on the ceiling which
angle is less than 15°as figure 2. GPCN-D can be installed to the
concrete-roof with ceiling or without ceiling, such as figure 3.
Connect the GPCN Main Bar Overview to the fixation (screws of
accessory ④ ). Store the power wire, and then fasten the front and
back screws of main bar. Finally, install the ornament board of
main bar as figure 4 and figure 5.
Hang the installation bracket (projecter has been installed) to the
adjuster as figure 6. And then put in the screws (accessory ④).but
do not fasten.Pull the top cup to the main bar, and then invaginate
the spring,figure 7
Install on
the ceiling
which angle
is less than
15°
Three steps of installation
figure 1
figure 2
figure 3
figure 4
figure 5
H
H
H
15°
figure 6
figure 7