Grange CONTEMPORARY PERGOLA User manual

CONTEMPORARY PERGOLA
PLAN
CONTEMPORARY PERGOLA (PKCPERGA)
1.83m
FOOTPRINT
1.83m
2.195m
1.83m
2.7m
Fig 1.
PLEASE SEE OVERLEAF FOR ASSEMBLY INSTRUCTIONS
GRANGE FENCING LIMITED
Halesfield 21, Telford TF7 4PA
Tel: [phone] Fax: [phone]
Email: [email protected] Web: www.grangefen.co.uk
OUT OF HOURS MESSAGE SERVICE:
01952 588088
JULY 2011 - ISSUE 2
NB. These instructions describe the concrete-in method of
fixing using 2.7m posts. Bolt Down Anchors or Spikes may
be used with 2.1m posts as alternative methods of fixing.
ALL PRODUCTS ARE MEASURED TO THE HIGHEST AND
WIDEST POINT AND ALL SIZES ARE APPROXIMATE
Grange Code: PKCPERGA
Contemporary Pergola Inst 8/7/11 09:59 Page 1

B
RAFTERS 2
C
RAFTERS 7
D
CURVED
BEAM
2
1. The Structure is spaced to allow standard
Grange panels to be inserted, if preferred, to
provide a screen. The distance between each of
the posts is therefore1830mm (see Fig.1).
2. The curved Beams (D) have to be fixed to the
Rafters (B). Mark the centres of the Rafter and
the Curved Beam and line up before fixing the
Curved Beam with screws (x)(see Fig.2).
3. Once this has been done, mark out the points
wherethe remaining rafters (C) will be fixed.
Two of the Rafters will locate in the top of the
posts to formasquarestructure. Therefore, two
points between the centre and the morticed
point need to be marked.
4. Beginning with two Posts for the front of the
structure, position them where they will be
fixed. Do NOT fix at this point.
5. Next, insert one of the Rafters with a Curved
Beam attached into the tops of the Posts (Fig.3).
6. The side Rafters locate within the tops of the
Posts and the Rafters with the Curved Beams
attached.
7. Locate the side Rafters into the assembled end
section, resting the free ends on the ground.
8. Assemble the other two Posts with a Rafter and
Curved Beam.
9. Locate the free ends of the side Rafters into the
Posts to create a square structure.
10.Fix the four corner points with screws (x).
11. Fix the remaining five Rafters at the points
previously marked starting at the centre.
12. Ensure the structure is vertical and square
before fixing the Posts in place (see Fig.4).
CONTEMPORARY PERGOLA
ASSEMBLY INSTRUCTIONS
Ref.
CROSS HEAD SCREWDRIVER
PARTS SUPPLIED
TOOLS REQUIRED (not supplied)
Description Qty.
A
POSTS 4
X
SCREWS 18
1x HARDWARE PACK & ACCESSORIES:
BEFORE YOU START
•Check the pack/s and make sure that you have
all of the parts listed above. If not, contact
your retailer who will be able to help you.
•When you are ready to start, make sure you
have the right tools to hand, plenty of space
and a clean, dryarea for assembly.
•It is advisable for two people to carry out
the work.
SITE PREPARATION
Excavate a 300mm square
hole (approx) for each
post to a depth of at least
300mm. (see Fig.A.right)
We would recommend
that you use MetCrete,
fast set post fixing
concrete to fix your posts.
Easy to use, it sets in just
10 minutes.
ASSEMBLY
Fig A.
300mm
Fig 2.
B
C D
A
=====
=
=
=
x
x
x
B
A
C
Fig 3.
Fig 4.
x
x
To ensure longevity of your structure it is
recommended that it is treated with a wood
preservative on a yearly basis.
AFTERCARE
Contemporary Pergola Inst 8/7/11 09:59 Page 2